| Age | Commit message (Collapse) | Author |
|---|
|
Cleanup by making local functions static.
The code to load config file is unreachable in net-next, probably came
from some out of tree driver.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When adding a new vxlan device to an "underlying carrier" (here:
dst->remote_ifindex), the MTU size assigned to the vxlan device
is the MTU at setup time of the carrier - needed headroom, when
adding a vxlan device w/o explicit carrier, then it defaults
to 1500.
In case of an explicit carrier that supports jumbo frames, we
currently cannot change vxlan MTU via ip(8) to > 1500 in
post-setup time, as vxlan driver uses eth_change_mtu() as default
method for manually setting MTU.
Hence, use a custom implementation that only falls back to
eth_change_mtu() in case we didn't use a dev parameter on device
setup time, and otherwise allow a max MTU setting of the carrier
incl. adjustment for headroom.
Reported-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
OMAP's ti_hecc driver is used to support the CAN controller on many omap2plus
SoCs (OMAP2430, OMAP3, OMAP4, OMAP5 and AM335x), so it's wrong to make this
depend on OMAP3 only. Take an extra step, to get wider build coverage, and make
the driver depend on ARM.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds Device Tree support to the Microchip MCP251X driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The ADM6996L switch and some Broadcom switches with two MII interfaces
like the BCM5325F connected to two MACs on the SoC, used on some
routers do not return a valid value when reading the PHY id register
and Linux thinks there is no PHY at all, but that is wrong.
This patch registers a fixed phy in the arch code and then searches it
when there is no other phy in the Ethernet driver code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
b44_phy_reset() will fail for an external PHY and only work with the
internal PHY, this was an old workaround when the detection of an
external switch based on the PHY address failed and it is not needed
any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this patch we can not access the PHY when the MAC is switched
off. This PHY access is needed to configure the switch, which is done
through PHY registers.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the older home routers based on the Broadcom BCM47XX SoC series
are using a MAC that is supported by b44. On most of these routers not
the internal PHY of this MAC core is used, but a switch sometimes on an
external chip or integrated into the same SoC as the Ethernet core.
For this switch a special PHY driver is needed which should not be
integrated into b44 as the same switches are also used by other
Broadcom home networking SoCs which are using different Ethernet MAC
drivers. This was tested with the b53 switch driver which is currently
on its way to mainline.
If the internal PHY is not used, b44 will now search on the MDIO bus
for a phy and use the Linux phylib subsystem to register a driver.
Support for the internal PHY must stay here, because there are some
device which are suing the internal phy.
With this patch we scan the mdio bus when the sprom or nvram says that
the PHY address is 30, if a PHY was found at this address b44 uses it.
This was tested with a BCM4704, BCM4712 and BCM5354.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patch will add these functions for phylib, and we should
rename the old ones before. This now indicates that these functions are
used for the mdio registers and on the mii interface.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the phy address is 31, this means that there is no PHY connected
to this MAC at all, no internal and no external PHY. Reading these PHY
registers causes a system reset on some routers.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY address 30 means there is no local PHY, but there could be an
external PHY like a switch connected via MII. This is the case on most
embedded home routers where this driver is used.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Ethernet core supported by b44 supports an internal PHY integrated
into the mac core, which is supported by the b44 driver and an external
PHY to which the mac core is connected. This external PHY could be a
switch connected through MII, which is often the case when this core is
used on home routers. The usage of an external PHY was assumed when the
PHY address 30 was used and an internal PHY was assumed when the PHY
address was different. To verify that b44_phy_reset() was called and
checked if it worked, otherwise PHY address 30 was assumed, an external
PHY. It is better to check the register which says which PHY is
connected to the MAC instead of checking the PHY address.
The interface to an external PHY was only activated when this register
was set.
This also changes B44_FLAG_INTERNAL_PHY to B44_FLAG_EXTERNAL_PHY, it is
easier to check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Save pkt_hash_types in tpa structure.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's no need anymore to call phy_init_hw() to reset/resume the PHY from the
driver, as the call chain in phylib already has reached it, and so reset/resumed
the PHY (even resuming it twice). This duplicate reset is not only needless, it
e.g. clears the PHY's interrupt enables just setup by phylib and so prevents the
expected IRQs from the PHY.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow the platform code to pass PHY's IRQ to the driver. Print this IRQ along
with the other PHY datails in sh_eth_phy_init().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to validate port number at mlx4_promisc_qp() before use.
Since port number is extracted from gid, as a cooked or corrupted gid
could lead to a crash.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add NAPI for TX side,
implement its support and provide NAPI callback.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MLX4_DEV_EVENT_SLAVE_INIT and MLX4_DEV_EVENT_SLAVE_SHUTDOWN
events used by Hypervisor to inform the PPF IB driver that
IB para-virtualization must be initialized/destroyed for a slave.
If this event is catched by ETH VF annoying but harmless error message
is printed into dmesg. Remove dmesg prints for these events.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To achieve out of the box performance default is to use 64 byte CQE/EQE.
In tests that we conduct in our labs, we achieved a performance
improvement of twice the message rate. For older VF/libmlx4 support,
enable_64b_cqe_eqe must be set to 0 (disabled).
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only TX rings of User Piority 0 are mapped.
TX rings of other UP's are using UP 0 mapping.
XPS is not in use when num_tc is set.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the port GUID read from the firmware to identify the physical port.
This port identifier is available via ndo_get_phys_port_id for both PF
and VF net-devices.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the infrastructure needed to support ndo_get_phys_port_id which
allows users to identify to which physical port a net-device is connected
to by reading a unique port id.
This will work for VFs and PFs.
The driver uses a new device capability - phys_port_id, The PF driver
reads the port phys_port_id from Firmware and stores it. The VF driver
reads the port phys_port_id from the PF using QUERY_FUNC_CAP command.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set nic_info field in QUERY_FUNC_CAP, which designates
supplementary NIC information is provided by the hypervisor.
When set, the following fields are valid: nic_num_rings,
nic_indirection_tbl_sz, cur_mac and phys_port_id.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use correct names for QUERY_FUNC_CAP fields: flags0 and flags1.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All mailboxes are already zeroed by commit:
571b8b9 net/mlx4_core: Initialize all mailbox buffers to zero before use
Remove explicit zero set for force mac and force vlan fields in
mlx4_QUERY_FUNC_CAP_wrapper
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch marks the function il_clear_traffic_stats() in debug.c as
static because they are not used outside this file.
Thus, it also removes the following warnings in
wireless/iwlegacy/debug.c:
drivers/net/wireless/iwlegacy/debug.c:35:1: warning: no previous prototype for ‘il_clear_traffic_stats’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch marks the function il4965_ucode_rx_stats_read(),
il4965_ucode_tx_stats_read() and il4965_ucode_general_stats_read() in
4965-debug.c as static because they are not used outside this file.
Thus, it also removes the following warnings in
wireless/iwlegacy/4965-debug.c:
drivers/net/wireless/iwlegacy/4965-debug.c:59:1: warning: no previous prototype for ‘il4965_ucode_rx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/4965-debug.c:471:1: warning: no previous prototype for ‘il4965_ucode_tx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/4965-debug.c:637:1: warning: no previous prototype for ‘il4965_ucode_general_stats_read’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch marks the function il3945_ucode_rx_stats_read(),
il3945_ucode_tx_stats_read() and il3945_ucode_general_stats_read() in
3945-debug.c as static because they are not used outside this file.
Thus, it also removes the following warnings in
wireless/iwlegacy/3945-debug.c:
drivers/net/wireless/iwlegacy/3945-debug.c:52:1: warning: no previous prototype for ‘il3945_ucode_rx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/3945-debug.c:317:1: warning: no previous prototype for ‘il3945_ucode_tx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/3945-debug.c:407:1: warning: no previous prototype for ‘il3945_ucode_general_stats_read’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a new header file include/net/Space.h which contains
prototype declaration of sbni_probe().
Include the new header file in drivers/net/Space.c and
drivers/net/wan/sbni.c because they use this function.
This eliminates the following warning in wan/sbni.c:
drivers/net/wan/sbni.c:224:12: warning: no previous prototype for ‘sbni_probe’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch marks the function stmmac_pltfr_freeze() and
stmmac_pltfr_restore() in stmmac_platform.c as static because they are
not used outside this file.
Thus, it also removes the following warnings in
ethernet/stmicro/stmmac/stmmac_platform.c:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:222:5: warning: no previous prototype for ‘stmmac_pltfr_freeze’ [-Wmissing-prototypes]
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:236:5: warning: no previous prototype for ‘stmmac_pltfr_restore’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch marks the function qlcnic_83xx_clear_legacy_intr_mask(),
qlcnic_83xx_set_legacy_intr_mask() and
qlcnic_83xx_enable_legacy_msix_mbx_intr() in qlcnic_83xx_hw.c as static
because they are not used outside this file.
Thus, it also removes the following warnings
in ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:318:13: warning: no previous prototype for ‘qlcnic_83xx_clear_legacy_intr_mask’ [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:323:13: warning: no previous prototype for ‘qlcnic_83xx_set_legacy_intr_mask’ [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:343:13: warning: no previous prototype for ‘qlcnic_83xx_enable_legacy_msix_mbx_intr’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch marks the function qlcnic_enable_tx_intr(),
qlcnic_83xx_enable_tx_intr() and qlcnic_83xx_disable_tx_intr() in
qlcnic_io.c as static because they are not used outside this file.
Thus, it also removes the following warnings in
ethernet/qlogic/qlcnic/qlcnic_io.c:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c:130:13: warning: no previous prototype for ‘qlcnic_enable_tx_intr’ [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c:147:13: warning: no previous prototype for ‘qlcnic_83xx_enable_tx_intr’ [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c:153:13: warning: no previous prototype for ‘qlcnic_83xx_disable_tx_intr’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IFLA_BOND_PACKETS_PER_SLAVE to allow get/set of bonding parameter
packets_per_slave via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IFLA_BOND_LP_INTERVAL to allow get/set of bonding parameter
lp_interval via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IFLA_BOND_MIN_LINKS to allow get/set of bonding parameter
min_links via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IFLA_BOND_ALL_SLAVES_ACTIVE to allow get/set of bonding parameter
all_slaves_active via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IFLA_BOND_NUM_PEER_NOTIF to allow get/set of bonding parameter
num_grat_arp via netlink. Bonding parameter num_unsol_na is
synonymous with num_grat_arp, so add only one netlink attribute
to represent both bonding parameters.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
this is a pull request of four patches for net-next/master.
There is one patch by Markus Pargmann, which speeds up the c_can
driver, a patch by John Whitmore which updates the in tree
documentation. A patch by Jeff Kirsher which replaces the FSF's address
by a link and a patch by Alexander Shiyan which converts the mcp251x
driver to make use of managed resources.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netback already has code which parses IPv4 and v6 headers to set up checksum
offsets and these are always applied to GSO packets being sent from
frontends. It's therefore suboptimal that GSOs are being marked
SKB_GSO_DODGY to defer the gso_segs calculation when netback already has all
necessary information to hand to do the calculation. This patch adds that
calculation.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warning:
drivers/net/ethernet/sfc/falcon.c:2601:6: warning:
symbol 'falcon_pull_nic_stats' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added software timestamping ability. Tested with linuxptp and synchronized
clocks to an average of less than 200 microseconds on 10 megabit ethernet.
Tested on both Vortex and Boomerang models.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I don't think the in-kernel drivers ever hit this strcpy() so this
doesn't change how the code works. But strlcpy() is safer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
