| Age | Commit message (Collapse) | Author |
|---|
|
Add a new helper to_hid_driver() and use it in hid-core.c.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Use to_hid_device() instead of container_of().
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
to_hid_device() macro is defined in both hid-lg4ff.c and
hid-logitech-hidpp.c. So I move it to include/linux/hid.h.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Ensure that the G920 is not given the default deadzones.
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The Logitech G920 uses a couple of vendor specific usage pages,
which results in incorrect number of axis/buttons being detected.
This patch adds these pages to the 'ignore' list.
Reported-by: Elias Vanderstuyft <elias.vds@gmail.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The G920 can adjust the amount of 'turn' it permits, this patch adds
a sysfs file 'range' to control this.
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch adds basic support for the Logitech G920 wheel when in HID
mode. This wheel 'speaks' the HID++ protocol, and therefor is driven
with hid-logitech-hidpp.
At this stage the driver only shows that it can communicate with the
wheel by outputting the name discovered over HID++.
The normal HID functions work to give input functionality using
joystick/event interface.
Note: in 'hidpp_probe()' we have to start the hardware to get packets
flowing, the same might apply in future for other devices which don't
use the unifying protocol.
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Patch add support for the 'very long' HID++ packets, which are
64 bytes in length.
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Pull the branch that has been established to be jointly merged to both hid.git
and input.git, because both trees have different depending patches on top.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
When plugged in the Logitech G920 wheel starts with USBID 046d:c261
and behaviors as a vendor specific class. If a 'magic' byte sequence
is sent the wheel will detach and reconnect as a HID device with the
USBID 046d:c262.
Signed-off-by: Simon Wood <simon@mungewell.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
"Two functional fixes for wacom HID driver from Ping Cheng and Jiri
Kosina"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: fixup quirks setup for WACOM_DEVICETYPE_PAD
HID: wacom: Add outbounding area for DTU1141
|
|
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.4 rc2. It's based on a commit
prior rc1 as I wanted to get them a bit more tested in next before
sending you the pull request.
MMC core:
- Improve reliability when selecting HS200 mode
- Improve reliability when selecting HS400 mode
- mmc: remove bondage between REQ_META and reliable write
MMC host:
- pxamci: Fix read-only gpio detection polarity
- mtk-sd: Preinitialize delay_phase to fix the case when delay is zero
- android-goldfish: Fix build dependency by adding HAS_DMA
- dw_mmc: Remove Seungwon Jeon from MAINTAINERS"
* tag 'mmc-v4.4-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: remove bondage between REQ_META and reliable write
mmc: MMC_GOLDFISH should depend on HAS_DMA
mmc: mediatek: Preinitialize delay_phase in get_best_delay()
MAINTAINERS: mmc: Remove Seungwon Jeon from dw_mmc
mmc: mmc: Improve reliability of mmc_select_hs400()
mmc: mmc: Move mmc_switch_status()
mmc: mmc: Fix HS setting in mmc_select_hs400()
mmc: mmc: Improve reliability of mmc_select_hs200()
mmc: pxamci: fix read-only gpio detection polarity
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Assorted bug fixes, the mlock2 system call gets added, and one
improvement. The boot from dasd devices is now possible from a wider
range of devices"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: remove SALIPL loader
s390: wire up mlock2 system call
s390: remove g5 elf platform support
s390: avoid cache aliasing under z/VM and KVM
s390/sclp: _sclp_wait_int(): retain full PSW mask
s390/zcrypt: Fix initialisation when zcrypt is built-in
s390/zcrypt: Fix kernel crash on systems without AP bus support
s390: add support for ipl devices in subchannel sets > 0
s390/ipl: fix out of bounds access in scpdata_write
s390/pci_dma: improve debugging of errors during dma map
s390/pci_dma: handle dma table failures
s390/pci_dma: unify label of invalid translation table entries
s390/syscalls: remove system call number calculation
s390/cio: simplify css_generate_pgid
s390/diag: add a s390 prefix to the diagnose trace point
s390/head: fix error message on unsupported hardware
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix build issues in scpi and ina2xx drivers, update scpi driver to
support recent firmware, and fix an uninitialized variable warning in
applesmc driver"
* tag 'hwmon-for-linus-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (scpi) skip unsupported sensors properly
hwmon: (scpi) add thermal-of dependency
hwmon : (applesmc) Fix uninitialized variables warnings
hwmon: (ina2xx) Fix build issue by selecting REGMAP_I2C
|
|
Pull networking fixes from David Miller:
1) Fix list tests in netfilter ingress support, from Florian Westphal.
2) Fix reversal of input and output interfaces in ingress hook
invocation, from Pablo Neira Ayuso.
3) We have a use after free in r8169, caught by Dave Jones, fixed by
Francois Romieu.
4) Splice use-after-free fix in AF_UNIX frmo Hannes Frederic Sowa.
5) Three ipv6 route handling bug fixes from Martin KaFai Lau:
a) Don't create clone routes not managed by the fib6 tree
b) Don't forget to check expiration of DST_NOCACHE routes.
c) Handle rt->dst.from == NULL properly.
6) Several AF_PACKET fixes wrt transport header setting and SKB
protocol setting, from Daniel Borkmann.
7) Fix thunder driver crash on shutdown, from Pavel Fedin.
8) Several Mellanox driver fixes (max MTU calculations, use of correct
DMA unmap in TX path, etc.) from Saeed Mahameed, Tariq Toukan, Doron
Tsur, Achiad Shochat, Eran Ben Elisha, and Noa Osherovich.
9) Several mv88e6060 DSA driver fixes (wrong bit definitions for
certain registers, etc.) from Neil Armstrong.
10) Make sure to disable preemption while updating per-cpu stats of ip
tunnels, from Jason A. Donenfeld.
11) Various ARM64 bpf JIT fixes, from Yang Shi.
12) Flush icache properly in ARM JITs, from Daniel Borkmann.
13) Fix masking of RX and TX interrupts in ravb driver, from Masaru
Nagai.
14) Fix netdev feature propagation for devices not implementing
->ndo_set_features(). From Nikolay Aleksandrov.
15) Big endian fix in vmxnet3 driver, from Shrikrishna Khare.
16) RAW socket code increments incorrect SNMP counters, fix from Ben
Cartwright-Cox.
17) IPv6 multicast SNMP counters are bumped twice, fix from Neil Horman.
18) Fix handling of VLAN headers on stacked devices when REORDER is
disabled. From Vlad Yasevich.
19) Fix SKB leaks and use-after-free in ipvlan and macvlan drivers, from
Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
MAINTAINERS: Update Mellanox's Eth NIC driver entries
net/core: revert "net: fix __netdev_update_features return.." and add comment
af_unix: take receive queue lock while appending new skb
rtnetlink: fix frame size warning in rtnl_fill_ifinfo
net: use skb_clone to avoid alloc_pages failure.
packet: Use PAGE_ALIGNED macro
packet: Don't check frames_per_block against negative values
net: phy: Use interrupts when available in NOLINK state
phy: marvell: Add support for 88E1540 PHY
arm64: bpf: make BPF prologue and epilogue align with ARM64 AAPCS
macvlan: fix leak in macvlan_handle_frame
ipvlan: fix use after free of skb
ipvlan: fix leak in ipvlan_rcv_frame
vlan: Do not put vlan headers back on bridge and macvlan ports
vlan: Fix untag operations of stacked vlans with REORDER_HEADER off
via-velocity: unconditionally drop frames with bad l2 length
ipg: Remove ipg driver
dl2k: Add support for IP1000A-based cards
snmp: Remove duplicate OUTMCAST stat increment
net: thunder: Check for driver data in nicvf_remove()
...
|
|
The NOLINK state will poll the phy once a second to see if the link
has come up. If the phy has an interrupt line, this polling can be
skipped, since the phy should interrupt when the link returns.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 88E1540 can be found embedded in the Marvell 88E6352 switch. It
is compatible with the 88E1510, so add support for it, using the
88E1510 specific functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reset pskb in macvlan_handle_frame in case skb_share_check returned a
clone.
Fixes: 8a4eb5734e8d ("net: introduce rx_handler results and logic around that")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipvlan_handle_frame is a rx_handler, and when it returns a value other
than RX_HANDLER_CONSUMED (here, NET_RX_DROP aka RX_HANDLER_ANOTHER),
__netif_receive_skb_core expects that the skb still exists and will
process it further, but we just freed it.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass a **skb to ipvlan_rcv_frame so that if skb_share_check returns a
new skb, we actually use it during further processing.
It's safe to ignore the new skb in the ipvlan_xmit_* functions, because
they call ipvlan_rcv_frame with local == true, so that dev_forward_skb
is called and always takes ownership of the skb.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By default the driver allowed incorrect frames to be received. What is
worse the code does not handle very short frames correctly. The FCS
length is unconditionally subtracted, and the underflow can cause
skb_put to be called with large number after implicit cast to unsigned.
And indeed, an skb_over_panic() was observed with via-velocity.
This removes the module parameter as it does not work in it's
current state, and should be implemented via NETIF_F_RXALL if needed.
Suggested-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a bug in the qat driver where a user-space pointer is
dereferenced"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: qat - don't use userspace pointer
|
|
Given that INTUOSHT < BAMBOO_PT
features->type >= INTUOSHT || features->type <= BAMBOO_PT
condition is always true, and therefore device_type is under certain
circumstances wrongly set with WACOM_DEVICETYPE_PAD bit set.
Fix the condition so that it actually represents the range as intended.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Now that IP1000A chips are supported by dl2k driver, the buggy ipg
driver can be removed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.
This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.
Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
vendor=0x13f0 device=0x1023 (rev 0x41)
subsystem vendor=0x1043 device=0x8180
MAC address registers access needed to be changed from 8-bit to 16-bit
because 8-bit does not work on IP1000A. 8-bit access is not even
allowed in the TC9020 datasheet (although it worked). 16-bit access
works on both.
Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
a rebranded TC9020):
vendor=0x1186 device=0x4000 (rev 0x0c)
subsystem vendor=0x1186 device=0x4000
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases the crash is caused by nicvf_remove() being called from
outside. For example, if we try to feed the device to vfio after the
probe has failed for some reason. So, move the check to better place.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 05cc5a39ddb7 "bnx2x: add vlan filtering offload" introduced
a regression in regard for vlans for 57710, 57711 adapters -
Loading 8021q module on a machine with such an adapter would cause
a null pointer dereference, as the driver mistakenly publishes it
has capabilities for vlan CTAG filtering.
Reported-by: Otto Sabart <osabart@redhat.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver does not handle the AVB-DMAC Receive FIFO Warning interrupt
now, so the interrupt should not be enabled.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Reported-by: Masao Uebayashi <uebayasi@gmail.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since Dell DW5580 is a 3G modem, this patch adds the device as a
mobile broadband adapter
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove rsstable array and its initialization from be_set_rss_hash_opts().
The array became unused after "e255787 be2net: Support for configurable
RSS hash key". The initial RSS table is now filled and stored for later
usage during Rx queue creation.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When RX/TX interrupt for Network Control queue and Best Effort queue
is issued at the same time, the interrupt mask of Network Control
queue will be reset when the mask of Best Effort queue is set.
This patch fixes this problem.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On certain hardware after software reboot the chip may get stuck and fail
to reinitialize during reset. This can be fixed by ensuring that PHY is
reset too.
Old PHY resetting method required operational MDIO interface, therefore
the chip should have been already set up. In order to be able to function
during probe, it is changed to use PMT_CTRL register.
The problem could be observed on SMDK5410 board.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the Vitesse VSC8601 PHY. Generic functions are
used for everything except interrupt handling.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 77a993942 "phy/at8031: enable at8031 to work on interrupt mode"
added interrupt support for the 8031 PHY but left out the other two
chips supported by this driver.
This patch sets the .ack_interrupt and .config_intr functions for the
8030 and 8035 drivers as well.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently it's assumed that firmware exports only the class of sensors
supported by the driver. However with newer firmware or SCPI protocol
revision, support for newer classes of sensors can be present.
The driver fails to probe with the following warning if an unsupported
class of sensor is encountered in the firmware.
sysfs: cannot create duplicate filename
'/devices/platform/scpi/scpi:sensors/hwmon/hwmon0/'
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:31
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u12:0 Not tainted 4.3.0-rc7 #137
Hardware name: ARM Juno development board (r0) (DT)
Workqueue: deferwq deferred_probe_work_func
PC is at sysfs_warn_dup+0x54/0x78
LR is at sysfs_warn_dup+0x54/0x78
This patch fixes the above issue by skipping through the unsupported
class of SCPI sensors.
Fixes: 68acc77a2d51 ("hwmon: Support thermal zones registration for SCP temperature sensors")
Fixes: ea98b29a05e9 ("hwmon: Support sensors exported via ARM SCP interface")
Cc: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The newly added scpi thermal support is broken when the scpi driver
is built-in but the thermal driver is a loadable module:
drivers/built-in.o: In function `scpi_hwmon_probe':
(.text+0x444d70): undefined reference to `thermal_zone_of_sensor_unregister'
(.text+0x444d94): undefined reference to `thermal_zone_of_sensor_register'
drivers/built-in.o: In function `scpi_hwmon_remove':
(text+0x444e6c): undefined reference to `thermal_zone_of_sensor_unregister'
This uses the same Kconfig trick that we have in a couple of other
drivers already to ensure we can only select the driver in valid
configurations when either THERMAL_OF is disabled, or when with a
dependency on CONFIG_THERMAL that can force SCPI to be a loadable
module in the case I was hitting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 68acc77a2d51 ("hwmon: Support thermal zones registration for SCP temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix the following "maybe used uninitialized" warnings by
initializing the variables to keep the compiler quiet.
There is no "used uninitialized" in this case.
CC [M] drivers/hwmon/applesmc.o
drivers/hwmon/applesmc.c: In function ‘applesmc_init_smcreg’:
drivers/hwmon/applesmc.c:595:43: warning: ‘right_light_sensor’
may be used uninitialized in this function [-Wmaybe-uninitialized]
s->num_light_sensors = left_light_sensor + right_light_sensor;
^
drivers/hwmon/applesmc.c:540:26: note: ‘right_light_sensor’ was
declared here
bool left_light_sensor, right_light_sensor;
^
drivers/hwmon/applesmc.c:595:43: warning: ‘left_light_sensor’ may
be used uninitialized in this function [-Wmaybe-uninitialized]
s->num_light_sensors = left_light_sensor + right_light_sensor;
^
drivers/hwmon/applesmc.c:540:7: note: ‘left_light_sensor’ was
declared here
bool left_light_sensor, right_light_sensor;
^
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since a0de56c81fcf ("hwmon: (ina2xx) convert driver to using regmap")
the driver requires REGMAP_I2C to build. Select it by default
in Kconfig.
Reported-by: Guo Chunrong <B40290@freescale.com>
Cc: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Fixes: a0de56c81fcf ("hwmon: (ina2xx) convert driver to using regmap")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
To align with the mv88e6xxx code, use the register defines to
access all the register addresses and bit fields.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To align with the mv88e6xxx code, add a similar header file
with all the register defines.
The file is based on the mv88e6xxx header for coherency.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the mv88e6060 datasheet, the first mac byte must
be at position 9 instead of 8 since the bit 8 is used to select
if the mac address must differ for each port for Pause frames.
Use the correct shift and set the same mac address for all port.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the mv88e6060 datasheet, the MaxFrameSize bit position
is 10 instead of 11 which is reserved.
Use the bit correctly to setup max frame size to 1536.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the mv88e6060 datasheet, the InitReady bit position
is 11 and the polarity is inverted.
Use the bit correctly to detect the end of initialization.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As of mv88e6xxx remove the poll_link callback since the link
state change polling is now handled by the phylib.
Tested on a mv88e6060 B0 device with a TI DM816X SoC.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The err variable wasn't set with the correct error value in some cases.
Fixes: 47605df95398 ('mlx4: Modify proxy/tunnel QP mechanism [..]')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When cleaning slave's counter resources, we hold a spinlock that
protects the slave's counters list. As part of the clean, we call
__mlx4_clear_if_stat which calls mlx4_alloc_cmd_mailbox which is a
sleepable function.
In order to fix this issue, hold the spinlock, and copy all counter
indices into a temporary array, and release the spinlock. Afterwards,
iterate over this array and free every counter. Repeat this scenario
until the original list is empty (a new counter might have been added
while releasing the counters from the temporary array).
Fixes: b72ca7e96acf ("net/mlx4_core: Reset counters data when freed")
Reported-by: Moni Shoua <monis@mellanox.com>
Tested-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
