| Age | Commit message (Collapse) | Author |
|---|
|
The Moorestown support was removed by commit 1a8359e411eb ("x86/mid: Remove
Intel Moorestown").
Remove this leftover.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The GPIO charger is using a mix of the legacy GPIO interface
and <linux/of_gpio.h> which is not the modern way to use GPIOs.
Refactor like this:
- Use a GPIO descriptor for the GPIO line used to monitor the
charger.
- Fetch the descriptor with devm_gpiod_get() as the first
method.
- If this fails and we are *not* using device tree, then
start looking to see if we can use platform data instead.
- After looking up and requesting a GPIO number with the
legacy API, convert it to a descriptor.
This way we can later isolate and drop the legacy code as
more platforms move over to using descriptors.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
trivial fix to spelling mistake in comments in the headers
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
pdata is being null checked twice, the 2nd check is redundant code
and can be removed.
Fixes CoverityScan CID 1392340 "Logically dead code"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Setting the irq_enable bits is taken care of by the irq chip when we
request the irqs and the driver should not be meddling with the
irq?_en registers itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
If there is no ti,ac-detect-gpios configured, it is normal to
have failed reads of the options register. So, hold back on the
log spamming.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
It is possible to verify AC adapter presence via a register read, without
any physical connection to the ACOK pin on the charger. Allow this.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Prior to this commit the code was using 1 notifier_block for all
types of charger cable, this is incorrect as the notifier_block
becomes part of a linked-list and now the same notifier_block
is part of 3 linked lists.
This commit fixes this by using a separate nb per extcon cable.
Note this happened to work fine sofar because axp288_charger was the only
listener, so when added to each of the 3 notifier chains, the next pointer
in the nb would be set to 0, so we've 3 heads pointing to the same nb,
with its next pointing to NULL. But as soon as we mix in a second extcon
consumer things will go boom.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Add a MODULE_DEVICE_TABLE to fix the module not auto-loading.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Setting the irq_enable bits is taken care of by the irq chip when we
request the irqs and the driver should not be meddling with the
irq?_en registers itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
To set a bit to 1 one needs to pass the mask for the bit to set
as second argument into regmap_update_bits, not "1".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Do not wait for an extcon notification before processing the cable
states, instead queue the otg / cable work on probe to make sure we
immediately process the initial hardware state.
Note this also requiree moving the getting of the USB_HOST cable state
from the extcon notifier to the workqueue function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Remove info->health, info->present and info->online caching, as no code
is reading the cached values.
Remove if (changed) check before calling power_supply_changed(), we
return early from axp288_charger_extcon_evt_worker if nothing has
changed, so the check is not needed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Deal with the charger type changing without a vbus-disconnect being
reported in between the 2 charger type states:
-Do not return from axp288_charger_extcon_evt_worker early in this case
(track old_chg_type)
-Make calling axp288_charger_enable_charger with the same value as before
a nop, to avoid the need for the caller to check this
-Do no do a dev_err when axp288_charger_enable_charger returns an error,
axp288_charger_enable_charger already returns an error itself
-Disable the charger before changing the charge-current setting (nop if
vbus was seen as disconnected before the change)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Nothing was setting info->otg.cable, so the extcon_get_cable_state_
calls on it would always return -EINVAL.
This commit fixes this by actually setting info->otg.cable using the new
extcon_get_extcon_dev_by_cable_id function.
This commit also makes failing to register the extcon notifier for the
USB_HOST cable an error rather then a warning, because we MUST have this
notfier to properly disable the VBUS path when in host mode so that we're
not drawing current from the 5V boost converter which is supplying power
to the otg port when in host mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Move the charger_init_hw_regs() above the power_supply_register call,
the axp288_charger_usb_set_property() uses axp288_chrg_info.max_cv and
.max_cc which get set by charger_init_hw_regs().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The extcon notifier work calls power_supply_changed on the power_supply
we register, so the extcon notifiers should be registered after we
register the power_supply.
While touching this code anyways, refactor the code for the 3 cable types
into a loop to avoid code repetition.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Use devm_power_supply_register instead of power_supply_register,
this avoids the need to do manual cleanup and results in quite
a nice code cleanup.
Note it may seem excessive to add a "struct device *dev" helper local
variable for the 1 time it is used in this patch, but future patches
in this series also use it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
|
|
This adds support for sbs-charger compilant chips as defined here:
http://sbs-forum.org/specs/sbc110.pdf
This was tested on a arm board connected to an LTC4100 battery charger
chip.
Signed-off-by: Nicolas Saenz Julienne <nicolas.saenz@prodys.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
So what if there is a status_gpio specified? bq24735_charger_is_present()
do have a working fallback for the case of no status_gpio.
Simplify this by not special casing setups w/o status_gpio, folding
two consecutive if-blocks in the process.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
During probe, it makes no sense to take care to first not issue any
i2c commands to verify if the connected part really is a bq24735, to
later simply fail the probe in the next step when trying to configure
the charger. So, delay configuration of the charging parameters until
the charger is accessible (i.e. when the AC adapter is present) as
part of enabling the charging.
This also fixes the rather serious issue that the charging parameters
are lost when the AC adapter is disconnected.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
bq24735_enable_charging() needs to call bq24735_config_charging(),
which is something to change later, this is just a preparatory patch.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
"tps65217-charger" is more appropriate name because the driver supports
not only AC but also USB charger.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Rename it as tps65217_charger_get_property().
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Replace 'ac_props' with 'charger_props'.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Replace 'ac' of tps65217_charger structure with 'psy'.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
This driver supports AC and USB chargers. Generic name is preferred.
Replace 'ac_online' with 'online'.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
TPS65217 has two charger interrupts - AC and USB power status change.
Interrupt number in the TPS65217 driver data:
IRQ number is only used on requesting the interrupt, so no need to keep
it inside the driver data.
Interrupt handler:
Check not only AC but also USB charger status.
In both cases, enable charging operation.
Interrupt request:
If an interrupt number is invalid, then use legacy polling thread.
Otherwise, create IRQ threads to handle AC and USB charger event.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Use the task_struct variable for running polling thread. If polling task
is activated, then use it to stop running thread.
This is a preceding step of supporting two interrupts of TPS65217 charger,
so checking single IRQ number is not appropriate when the module is removed.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
This patch replaces the deprecated extcon API as following:
- extcon_set_cable_state_() -> extcon_set_state_sync()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
This patch uses the resource-managed extcon API for extcon_register_notifier()
and replaces the deprecated extcon API as following:
- extcon_get_cable_state_() -> extcon_get_state()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Use managed resource function devm_power_supply_register instead of
power_supply_register to simplify the error path by allowing unregistering
to happen automatically on error and remove.
Removing max8997_battery_remove function also as it is now redundant.
Also removing out of memory printk message after kzalloc as there is
already enough information on failure.
Signed-off-by: Srikant Ritolia <s.ritolia@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The X-Powers AXP223 shares most of its behaviour with the AXP221 PMIC
but allows the VBUS power supply max current to be set to 100mA (like
the AXP209 PMIC).
This basically adds a new compatible to the VBUS power supply driver and
adds a check on the compatible when setting current max limit.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
AXP20X and AXP22X PMICs allow setting the min voltage and max current of
VBUS power supply. This adds entries in sysfs to allow to do so.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
device_is_compatible
This replaces calls to of_device_is_compatible to check data field of
of_device_id matched when probing the driver.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
If the ac-detect gpio does not support interrupts, provide a fallback
to poll the gpio at a configurable interval.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
In order for the MSB -> LSB latching to work correctly we must read the
2 8 bit registers of a 12 bit value in one consecutive read.
This fixes voltage_ocv reporting inconsistent values on my tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
In order for the MSB -> LSB latching to work correctly we must read the
2 8 bit registers of a 15 bit value in one consecutive read.
This fixes charge_full reporting 3498768 on some reads and 3354624 one
other reads on my tablet (for the 3354624 value the raw LSB is 0x00).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
If reading the register fails, return the actual error code, instead
of the uninitialized val variable;
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Providing value bits outside of the mask is pointless.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
When the axp288_faul_gauge driver was originally merged, it was
merged with a dependency on some other driver providing platform
data for it.
However the battery-data-framework which should provide that data
never got merged, resulting in x86 tablets / laptops with an axp288
having no working battery monitor, as before this commit the driver
would simply return -ENODEV if there is no platform data.
This commit removes the dependency on the platform_data instead
checking that the firmware has initialized the fuel-gauge and
reading the info back from the pmic.
What is missing from the read-back info is the table to map raw adc
values to temperature, so this commit drops the temperature and
temperature limits properties. The min voltage, charge design and
model name info is also missing. Note that none of these are really
important for userspace to have.
All other functionality is preserved and actually made available
by this commit.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=88471
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
When the axp288_charger driver was originally merged, it was merged with
a dependency on some other driver providing platform data for it.
However the battery-data-framework which should provide that data never
got merged, so the axp288_charger as merged upstream has never worked,
its probe method simply always returns -ENODEV.
This commit removes the dependency on the platform_data instead reading
back the charging current and charging voltage that the firmware has set
and using those values as the maximum values the user may set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Make charger_init_hw_regs propagate i2c errors, instead of only warning
about them and then ignoring them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The timer type simplifications caused a new gcc warning:
drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’:
drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized]
elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));
despite the actual use of "time_start" not having changed in any way.
It appears that simply changing the type of ktime_t from a union to a
plain scalar type made gcc check the use.
The variable wasn't actually used uninitialized, but gcc apparently
failed to notice that the conditional around the use was exactly the
same as the conditional around the initialization of that variable.
Add an unnecessary initialization just to shut up the compiler.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer type cleanups from Thomas Gleixner:
"This series does a tree wide cleanup of types related to
timers/timekeeping.
- Get rid of cycles_t and use a plain u64. The type is not really
helpful and caused more confusion than clarity
- Get rid of the ktime union. The union has become useless as we use
the scalar nanoseconds storage unconditionally now. The 32bit
timespec alike storage got removed due to the Y2038 limitations
some time ago.
That leaves the odd union access around for no reason. Clean it up.
Both changes have been done with coccinelle and a small amount of
manual mopping up"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP hotplug notifier removal from Thomas Gleixner:
"This is the final cleanup of the hotplug notifier infrastructure. The
series has been reintgrated in the last two days because there came a
new driver using the old infrastructure via the SCSI tree.
Summary:
- convert the last leftover drivers utilizing notifiers
- fixup for a completely broken hotplug user
- prevent setup of already used states
- removal of the notifiers
- treewide cleanup of hotplug state names
- consolidation of state space
There is a sphinx based documentation pending, but that needs review
from the documentation folks"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/armada-xp: Consolidate hotplug state space
irqchip/gic: Consolidate hotplug state space
coresight/etm3/4x: Consolidate hotplug state space
cpu/hotplug: Cleanup state names
cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
staging/lustre/libcfs: Convert to hotplug state machine
scsi/bnx2i: Convert to hotplug state machine
scsi/bnx2fc: Convert to hotplug state machine
cpu/hotplug: Prevent overwriting of callbacks
x86/msr: Remove bogus cleanup from the error path
bus: arm-ccn: Prevent hotplug callback leak
perf/x86/intel/cstate: Prevent hotplug callback leak
ARM/imx/mmcd: Fix broken cpu hotplug handling
scsi: qedi: Convert to hotplug state machine
|
|
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
|
|
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
|
|
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
|
