| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas
Pull SH driver fix from Simon Horman:
"Confine SH_INTC to platforms that need it"
* tag 'renesas-sh-drivers-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
sh: intc: Confine SH_INTC to platforms that need it
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A couple of EFI fixes, plus misc fixes all around the map"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm64: Store Runtime Services revision
firmware: Do not use WARN_ON(!spin_is_locked())
x86_32, entry: Clean up sysenter_badsys declaration
x86/doc: Fix the 'tlb_single_page_flush_ceiling' sysconfig path
x86/mm: Fix sparse 'tlb_single_page_flush_ceiling' warning and make the variable read-mostly
x86/mm: Fix RCU splat from new TLB tracepoints
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes from this week, it's been pretty quiet and
nothing really stands out as particularly noteworthy here -- mostly
minor fixes across the field:
- ODROID booting was fixed due to PMIC interrupts missing in DT
- a collection of i.MX fixes
- minor Tegra fix for regulators
- Rockchip fix and addition of SoC-specific mailing list to make it
easier to find posted patches"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
bus: arm-ccn: Fix warning message
ARM: shmobile: koelsch: Remove non-existent i2c6 pinmux
ARM: tegra: apalis/colibri t30: fix on-module 5v0 supplies
MAINTAINERS: add new Rockchip SoC list
ARM: dts: rockchip: readd missing mmc0 pinctrl settings
ARM: dts: ODROID i2c improvements
ARM: dts: Enable PMIC interrupts on ODROID
ARM: dts: imx6sx: fix the pad setting for uart CTS_B
ARM: dts: i.MX53: fix apparent bug in VPU clks
ARM: imx: correct gpu2d_axi and gpu3d_axi clock setting
ARM: dts: imx6: edmqmx6: change enet reset pin
ARM: dts: vf610-twr: Fix pinctrl_esdhc1 pin definitions.
ARM: imx: remove unnecessary ARCH_HAS_OPP select
ARM: imx: fix TLB missing of IOMUXC base address during suspend
ARM: imx6: fix SMP compilation again
ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
- a largeish fix for the IRQ handling in the new Zynq driver. The
quite verbose commit message gives the exact details.
- move some defines for gpiod flags outside an ifdef to make stub
functions work again.
- various minor fixes that we can accept for -rc1.
* tag 'gpio-v3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio-lynxpoint: enable input sensing in resume
gpio: move GPIOD flags outside #ifdef
gpio: delete unneeded test before of_node_put
gpio: zynq: Fix IRQ handlers
gpiolib: devres: use correct structure type name in sizeof
MAINTAINERS: Change maintainer for gpio-bcm-kona.c
|
|
Pull drm fixes from Dave Airlie:
"Intel and radeon fixes.
Post KS/LC git requests from i915 and radeon stacked up. They are all
fixes along with some new pci ids for radeon, and one maintainers file
entry.
- i915: display fixes and irq fixes
- radeon: pci ids, and misc gpuvm, dpm and hdp cache"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
MAINTAINERS: Add entry for Renesas DRM drivers
drm/radeon: add additional SI pci ids
drm/radeon: add new bonaire pci ids
drm/radeon: add new KV pci id
Revert "drm/radeon: Use write-combined CPU mappings of ring buffers with PCIe"
drm/radeon: fix active_cu mask on SI and CIK after re-init (v3)
drm/radeon: fix active cu count for SI and CIK
drm/radeon: re-enable selective GPUVM flushing
drm/radeon: Sync ME and PFP after CP semaphore waits v4
drm/radeon: fix display handling in radeon_gpu_reset
drm/radeon: fix pm handling in radeon_gpu_reset
drm/radeon: Only flush HDP cache for indirect buffers from userspace
drm/radeon: properly document reloc priority mask
drm/i915: don't try to retrain a DP link on an inactive CRTC
drm/i915: make sure VDD is turned off during system suspend
drm/i915: cancel hotplug and dig_port work during suspend and unload
drm/i915: fix HPD IRQ reenable work cancelation
drm/i915: take display port power domain in DP HPD handler
drm/i915: Don't try to enable cursor from setplane when crtc is disabled
drm/i915: Skip load detect when intel_crtc->new_enable==true
...
|
|
A message warning a user about wrong vc value was printing
out port instead.
Reported-by: Drew Richardson <drew.richardson@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fix from Thierry Reding:
"Just one bugfix for the PWM lookup table code that would cause a PWM
channel to be set to the wrong period and polarity for non-perfect
matches"
* tag 'pwm/for-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: Fix period and polarity in pwm_get() for non-perfect matches
|
|
Pull networking fixes from David Miller:
"Here are some bug fixes that have piled up during ksummit/linuxcon.
1) Fix endian problems in ibmveth, from Anton Blanchard.
2) IPV6 routing code does GFP_KERNEL allocation in atomic, fix from
Benjamin Block.
3) SCTP association fixes from Daniel Borkmann.
4) When multiple VLAN headers are present we have to make sure the
second and subsequent ones are pullable in the SKB otherwise we
blindly dereference garbage. From Jiri Benc.
5) The argument adjustment of the signature of hlist_add_after*()
introduced a regression in the batman-adv code, fix from Sven
Eckelmann.
6) Fix TX hang handling to avoid a panic in i40e, from Anjali Singhai
Jain.
7) PTP flag test is inverted in i40e driver, from Jesse Brandeburg.
8) ATM LEC driver needs to hold RTNL mutex over MTU changes, from
Chas Williams.
9) Truncate packets larger then the TPACKET_V3 format configured
buffers, otherwise we overwrite past the end of said buffers.
From Eric Dumazet.
10) Fix endianness bugs in qlcnic firmware handling, from Rajesh
Borundia and Shahed Shaikh.
11) CXGB4 sometimes doesn't get all of the TX completion events it
should resulting in SKBs getting stuck in the TX queue, from
Hariprasad Shenai.
12) When the FEC chip's PTP clock is disabled, you can't access the
register. Add necessary checks to avoid the resulting hang, from
Fugang Duan"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
drivers: isdn: eicon: xdi_msg.h: Fix typo in #ifndef
net: sctp: fix suboptimal edge-case on non-active active/retrans path selection
net: sctp: spare unnecessary comparison in sctp_trans_elect_best
net: ethernet: broadcom: bnx2x: Remove redundant #ifdef
ibmveth: Fix endian issues with rx_no_buffer statistic
net: xgene: fix possible NULL dereference in xgene_enet_free_desc_rings()
openvswitch: fix panic with multiple vlan headers
net: ipv6: fib: don't sleep inside atomic lock
net: fec: ptp: avoid register access when ipg clock is disabled
cxgb4: Free completed tx skbs promptly
cxgb4: Fix race condition in cleanup
sctp: not send SCTP_PEER_ADDR_CHANGE notifications with failed probe
bnx2x: Revert UNDI flushing mechanism
qlcnic: Fix endianess issue in firmware load from file operation
qlcnic: Fix endianess issue in FW dump template header
qlcnic: Fix flash access interface to application
MAINTAINERS: Add section for MRF24J40 IEEE 802.15.4 radio driver
macvlan: Allow setting multicast filter on all macvlan types
packet: handle too big packets for PACKET_V3
MAINTAINERS: add entry for ec_bhf driver
...
|
|
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Test for definedness of the macro which is actually defined (the
change is hard to see: it is s/SSS/SSA/).
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nothing defines _ASM_GENERIC_INT_L64_H, it is a weird way to check for
64 bit longs, and u64 should be printed using %llx anyway.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hidden away in the last 8 bytes of the buffer_list page is a solitary
statistic. It needs to be byte swapped or else ethtool -S will
produce numbers that terrify the user.
Since we do this in multiple places, create a helper function with a
comment explaining what is going on.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A NULL pointer dereference is possible for the argument ring->buf_pool
which is passed to xgene_enet_free_desc_ring(), as ring could be NULL.
And now since NULL pointers are being checked for before the calls to
xgene_enet_free_desc_ring(), might as well take advantage of them and
not call the function if the argument would be NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current kernel hang on i.MX6SX with rootfs mount from MMC.
The root cause is that ptp uses a periodic timer to access enet register
even if ipg clock is disabled.
FEC ptp driver start one period timer to read 1588 counter register in the
ptp init function that is called after FEC driver is probed.
To save power, after FEC probe finish, FEC driver disable all clocks including
ipg clock that is needed for register access.
i.MX5x, i.MX6q/dl/sl FEC register access don't cause system hang when ipg clock
is disabled, just return zero value. But for i.MX6sx SOC, it cause system hang.
To avoid the issue, we need to check ptp clock status before ptp timer count access.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"The fixes include:
- fix a crash in the VT-d driver when devices with a driver attached
are hot-unplugged
- fix a AMD IOMMU driver crash with device assignment of 32 bit PCI
devices to KVM guests
- fix for a copy&paste error in generic IOMMU code. Now the right
function pointer is checked before calling"
* tag 'iommu-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/core: Check for the right function pointer in iommu_map()
iommu/amd: Fix cleanup_domain for mass device removal
iommu/vt-d: Defer domain removal if device is assigned to a driver
|
|
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=82912
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
spin_is_locked() always returns false for uniprocessor configurations
in several architectures, so do not use WARN_ON with it.
Use lockdep_assert_held() instead to also reduce overhead in
non-debug kernels.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
Description of problem:
The NIC card is not reporting back to the driver the transmitted skbs,
so they get stuck in the TX ring causing issues with reference
counters in other kernel components.
Developed a new Automatic Egress Queue Update firmware facility to slowly tick
through Egress Queues and send back any outstanding CIDX Updates which are
laying around.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2014-08-21
The first patch is from Mirza Krak, it fixes the initialization of the hardware
in the sja1000 driver. The next patch is contributed by Dan Carpenter, it fixes
the error handling in the c_can's probe function. Then there are two patches
for the flexcan driver, one by Alexander Stein, which fixes the resetting of
the bus error interrupt mask, the other one by Sebastian Andrzej Siewior which
adds an additional error state transition message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a possible race condition when we unregister the PCI Driver and then
flush/destroy the global "workq". This could lead to situations where there
are tasks on the Work Queue with references to now deleted adapter data
structures. Instead, have per-adapter Work Queues which were instantiated and
torn down in init_one() and remove_one(), respectively.
v2: Remove unnecessary call to flush_workqueue() before destroy_workqueue()
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the sh-intc driver is compiled on all SuperH and
non-multiplatform SH-Mobile platforms, while it's only used on a limited
number of platforms:
- SuperH: SH2(A), SH3(A), SH4(A)(L) (all but SH5)
- ARM: sh7372, sh73a0
Drop the "default y" on SH_INTC, make all CPU platforms that use it
select it, and protect all sub-options by "if SH_INTC" to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Commit 91ebb929b6f8 ("bnx2x: Add support for Multi-Function UNDI") [which was
later supposedly fixed by de682941eef3 ("bnx2x: Fix UNDI driver unload")]
introduced a bug in which in some [yet-to-be-determined] scenarios the
alternative flushing mechanism which was to guarantee the Rx buffers are
empty before resetting them during device probe will fail.
If this happens, when device will be loaded once more a fatal attention will
occur; Since this most likely happens in boot from SAN scenarios, the machine
will fail to load.
Notice this may occur not only in the 'Multi-Function' scenario but in the
regular scenario as well, i.e., this introduced a regression in the driver's
ability to perform boot from SAN.
The patch reverts the mechanism and applies the old scheme to multi-function
devices as well as to single-function devices.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware binary file is in little endian. On big-endian architecture, while
writing this binary FW file to adapters memory, writel() swaps the data resulting into
corruption of FW image. So, swap the data before writing into adapters memory.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware dump template header is read from adapter using
readl() which swaps the data. So, adjust structure
element on the boundary of 32bit dword.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Application expects flash data in little endian, but driver reads/writes
flash data using readl()/writel() APIs which swaps data on big endian machine.
So, swap the data after reading from and before writing to flash memory.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, macvlan code restricts multicast and unicast
filter setting only to passthru devices. As a result,
if a guest using macvtap wants to receive multicast
traffic, it has to set IFF_ALLMULTI or IFF_PROMISC.
This patch makes it possible to use the fdb interface
to add multicast addresses to the filter thus allowing
a guest to receive only targeted multicast traffic.
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://anongit.freedesktop.org/drm-intel
Display fixes from Ville and Imre, all cc: stable.
* tag 'drm-intel-fixes-2014-08-21' of git://anongit.freedesktop.org/drm-intel:
drm/i915: don't try to retrain a DP link on an inactive CRTC
drm/i915: make sure VDD is turned off during system suspend
drm/i915: cancel hotplug and dig_port work during suspend and unload
drm/i915: fix HPD IRQ reenable work cancelation
drm/i915: take display port power domain in DP HPD handler
drm/i915: Don't try to enable cursor from setplane when crtc is disabled
drm/i915: Skip load detect when intel_crtc->new_enable==true
drm/i915: Fix locking for intel_enable_pipe_a()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Nothing drastic but pushing out early due to build breakage in the new
tegra platform.
Additionally:
- M550 tagged trim blacklist pattern is widened so that it matches
the new 1TB model
- three controller specific fixes"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: widen Crucial M550 blacklist matching
pata_scc: propagate return value of scc_wait_after_reset
ata: ahci_tegra: Change include to fix compilation
pata_samsung_cf: change ret type to signed
ahci_xgene: Removing NCQ support from the APM X-Gene SoC AHCI SATA Host Controller driver.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fixes for a couple potential memory corruption problems (the HW would
have to be manufactured to be deliberately evil to trigger those)
found by Ben Hawkes
- fix for potential infinite loop when using sysfs interface of
logitech driver, from Simon Wood
- a couple more simple driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix a couple of off-by-ones
HID: logitech: perform bounds checking on device_id early enough
HID: logitech: fix bounds checking on LED report size
HID: logitech: Prevent possibility of infinite loop when using /sys interface
HID: rmi: print an error if F11 is not found instead of stopping the device
HID: hid-sensor-hub: use devm_ functions consistently
HID: huion: Use allocated buffer for DMA
HID: huion: Fail on parameter retrieval errors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here is the fixup for the 'lowlight' of my last pull request. I2C is
not selected anymore by I2C_ACPI. Instead, the code in question now
depends on I2C=y.
Also, Mika has agreed to support me and be the maintainer for I2C-ACPI
related patches. Finally, a new-ID-patch came along last week"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer for ACPI parts of I2C
i2c: i801: Add PCI ID for Intel Braswell
i2c: rework kernel config I2C_ACPI
|
|
There are a few very theoretical off-by-one bugs in report descriptor size
checking when performing a pre-parsing fixup. Fix those.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
device_index is a char type and the size of paired_dj_deivces is 7
elements, therefore proper bounds checking has to be applied to
device_index before it is used.
We are currently performing the bounds checking in
logi_dj_recv_add_djhid_device(), which is too late, as malicious device
could send REPORT_TYPE_NOTIF_DEVICE_UNPAIRED early enough and trigger the
problem in one of the report forwarding functions called from
logi_dj_raw_event().
Fix this by performing the check at the earliest possible ocasion in
logi_dj_raw_event().
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The check on report size for REPORT_TYPE_LEDS in logi_dj_ll_raw_request()
is wrong; the current check doesn't make any sense -- the report allocated
by HID core in hid_hw_raw_request() can be much larger than
DJREPORT_SHORT_LENGTH, and currently logi_dj_ll_raw_request() doesn't
handle this properly at all.
Fix the check by actually trimming down the report size properly if it is
too large.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
It appears that input sensing bit might be reset during
suspend/resume. Set input sensing again for all requested gpios
in resume
Tested-by: Jerome Blin <jerome.blin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Once the CAN-bus is open and a packet is sent, the controller switches
into the PASSIVE state. Once the BUS is closed again it goes the back
err-warning. The TX error counter goes 0 -> 0x80 -> 0x7f.
This patch makes sure that the user learns about this state chang
(CAN_STATE_ERROR_WARNING => CAN_STATE_ERROR_PASSIVE)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Matthias Klein <matthias.klein@optimeas.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In case we don't have FLEXCAN_HAS_BROKEN_ERR_STATE and the user set
CAN_CTRLMODE_BERR_REPORTING once it can not be unset again until reboot.
So in case neither hardware nor user wants the error interrupt disable
the bit.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
devm_ioremap() returns NULL on error, not an ERR_PTR().
Fixes: 33cf75656923 ('can: c_can_platform: Fix raminit, use devm_ioremap() instead of devm_ioremap_resource()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When sja1000 is not compiled as module the SJA1000 chip is only
initialized during device registration on kernel boot. Should the chip
get a hardware reset there is no way to reinitialize it without re-
booting the Linux kernel.
This patch adds a check in sja1000_start if the chip is initialized, if
not we initialize it.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Pull x86 platform driver revert from Matthew Garrett:
"This clearly shouldn't have been merged. No excuse on my part"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
Revert "platform/x86/toshiba-apci.c possible bad if test?"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"These are the two bug fixes I mentioned in the final merge window
pull. One is a reversed logic check in the device busy tests which
can cause a nasty hang and another crash seen in the new SCSI pool
support if the use count ever goes to zero"
[ The device busy test already got merged from a patch earlier, so is
now duplicated. ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] save command pool address of Scsi_Host
[SCSI] fix qemu boot hang problem
|
|
Make sure plane rotation is reset correctly when restoring the fbdev
configuration by using drm_mode_plane_set_obj_prop which calls the
driver's set_property callback.
The rotation reset feature was introduced in commit 9783de2 (drm:
Resetting rotation property) and the callback issue was originally
addressed in a previous version of the patch, but the fix was not
present in the final version.
v2: Fix documentation warning
Add some more details to the commit message (Daniel Vetter)
Testcase: igt/kms_rotation_crc
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82236
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This reverts commit bdc3ae7221213963f438faeaa69c8b4a2195f491.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
We still have a few missing bits and pieces to have execlists enabled by
default eg. the error capture or the render state initialization and so
it wouldn't be wise to enable it by default on BDW just yet.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82740
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The time has come, the Walrus said, to talk of many things.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Add theory of operation notes to intel_lrc.c and comments to externally
visible functions.
v2: Add notes on logical ring context creation.
v3: Use kerneldoc.
v4: Integrate it in the DocBook template.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com> (v1)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com> (v2, v3)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Drop hunk about render ring init function since that's not
yet merged.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This has turned out to be really handy in debug so far.
Update:
Since writing this patch, I've gotten similar code upstream for error
state. I've used it quite a bit in debugfs however, and I'd like to keep
it here at least until preemption is working.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
This patch was accidentally dropped in the first Execlists version, and
it has been very useful indeed. Put it back again, but as a standalone
debugfs file.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
v2: Take the device struct_mutex rather than mode_config mutex for
atomic state capture.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
v2: Warn and return if LRCs are not enabled.
v3: Grab the Execlists spinlock (noticed by Daniel Vetter).
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
v4: Lock the struct mutex for atomic state capture
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Up until recently, semaphores weren't enabled in BDW so we didn't care
about them. But then Rodrigo came and enabled them:
commit 521e62e49a42661a4ee0102644517dbe2f100a23
Author: Rodrigo Vivi <rodrigo.vivi@intel.com>
drm/i915: Enable semaphores on BDW
So now we have to explicitly disable them for Execlists until both
features play nicely.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If we reset a ring after a hang, we have to make sure that we clear
out all queued Execlists requests.
v2: The ring is, at this point, already being correctly re-programmed
for Execlists, and the hangcheck counters cleared.
v3: Daniel suggests to drop the "if (execlists)" because the Execlists
queue should be empty in legacy mode (which is true, if we do the
INIT_LIST_HEAD).
v4: Do the pending intel_runtime_pm_put
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
