summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2019-03-04sky2: Disable MSI on Dell Inspiron 1545 and Gateway P-79Kai-Heng Feng
Some sky2 chips fire IRQ after S3, before the driver is fully resumed: [ 686.804877] do_IRQ: 1.37 No irq handler for vector This is likely a platform bug that device isn't fully quiesced during S3. Use MSI-X, maskable MSI or INTx can prevent this issue from happening. Since MSI-X and maskable MSI are not supported by this device, fallback to use INTx on affected platforms. BugLink: https://bugs.launchpad.net/bugs/1807259 BugLink: https://bugs.launchpad.net/bugs/1809843 Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04net/mlx5e: Update tx reporter status in case channels were successfully openedEran Ben Elisha
Once channels were successfully opened, update tx reporter health state to healthy. This is needed for the following scenario: - SQ has an un-recovered error reported to the devlink health, resulting tx reporter state to be error. - Current channels (including this SQ) are closed - New channels are opened After that flow, the original error was "solved", and tx reporter state should be healthy. However, as it was resolved as a side effect, and not via tx reporter recover method, driver needs to inform devlink health about it. Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04team: Free BPF filter when unregistering netdevIdo Schimmel
When team is used in loadbalance mode a BPF filter can be used to provide a hash which will determine the Tx port. When the netdev is later unregistered the filter is not freed which results in memory leaks [1]. Fix by freeing the program and the corresponding filter when unregistering the netdev. [1] unreferenced object 0xffff8881dbc47cc8 (size 16): comm "teamd", pid 3068, jiffies 4294997779 (age 438.247s) hex dump (first 16 bytes): a3 00 6b 6b 6b 6b 6b 6b 88 a5 82 e1 81 88 ff ff ..kkkkkk........ backtrace: [<000000008a3b47e3>] team_nl_cmd_options_set+0x88f/0x11b0 [<00000000c4f4f27e>] genl_family_rcv_msg+0x78f/0x1080 [<00000000610ef838>] genl_rcv_msg+0xca/0x170 [<00000000a281df93>] netlink_rcv_skb+0x132/0x380 [<000000004d9448a2>] genl_rcv+0x29/0x40 [<000000000321b2f4>] netlink_unicast+0x4c0/0x690 [<000000008c25dffb>] netlink_sendmsg+0x929/0xe10 [<00000000068298c5>] sock_sendmsg+0xc8/0x110 [<0000000082a61ff0>] ___sys_sendmsg+0x77a/0x8f0 [<00000000663ae29d>] __sys_sendmsg+0xf7/0x250 [<0000000027c5f11a>] do_syscall_64+0x14d/0x610 [<000000006cfbc8d3>] entry_SYSCALL_64_after_hwframe+0x49/0xbe [<00000000e23197e2>] 0xffffffffffffffff unreferenced object 0xffff8881e182a588 (size 2048): comm "teamd", pid 3068, jiffies 4294997780 (age 438.247s) hex dump (first 32 bytes): 20 00 00 00 02 00 00 00 30 00 00 00 28 f0 ff ff .......0...(... 07 00 00 00 00 00 00 00 28 00 00 00 00 00 00 00 ........(....... backtrace: [<000000002daf01fb>] lb_bpf_func_set+0x45c/0x6d0 [<000000008a3b47e3>] team_nl_cmd_options_set+0x88f/0x11b0 [<00000000c4f4f27e>] genl_family_rcv_msg+0x78f/0x1080 [<00000000610ef838>] genl_rcv_msg+0xca/0x170 [<00000000a281df93>] netlink_rcv_skb+0x132/0x380 [<000000004d9448a2>] genl_rcv+0x29/0x40 [<000000000321b2f4>] netlink_unicast+0x4c0/0x690 [<000000008c25dffb>] netlink_sendmsg+0x929/0xe10 [<00000000068298c5>] sock_sendmsg+0xc8/0x110 [<0000000082a61ff0>] ___sys_sendmsg+0x77a/0x8f0 [<00000000663ae29d>] __sys_sendmsg+0xf7/0x250 [<0000000027c5f11a>] do_syscall_64+0x14d/0x610 [<000000006cfbc8d3>] entry_SYSCALL_64_after_hwframe+0x49/0xbe [<00000000e23197e2>] 0xffffffffffffffff Fixes: 01d7f30a9f96 ("team: add loadbalance mode") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Amit Cohen <amitc@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04isdn: mISDN: Fix potential NULL pointer dereference of kzallocAditya Pakki
Allocating memory via kzalloc for phi may fail and causes a NULL pointer dereference. This patch avoids such a scenario. Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04net: dsa: mv88e6xxx: support in-band signalling on SGMII ports with external ↵Heiner Kallweit
PHYs If an external PHY is connected via SGMII and uses in-band signalling then the auto-negotiated values aren't propagated to the port, resulting in a broken link. See discussion in [0]. This patch adds this propagation. We need to call mv88e6xxx_port_setup_mac(), therefore export it from chip.c. Successfully tested on a ZII DTU with 88E6390 switch and an Aquantia AQCS109 PHY connected via SGMII to port 9. [0] https://marc.info/?t=155130287200001&r=1&w=2 Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04cxgb4/chtls: Prefix adapter flags with CXGB4Arjun Vynipadath
Some of these macros were conflicting with global namespace, hence prefixing them with CXGB4. Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04mellanox: Switch to bitmap_zalloc()Andy Shevchenko
Switch to bitmap_zalloc() to show clearly what we are allocating. Besides that it returns pointer of bitmap type instead of opaque void *. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03mlxsw: i2c: Extend initialization by querying resources dataVadim Pasternak
Extend initialization flow by query requests for chip resources data in order to obtain chip's specific capabilities, like the number of ports. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03mlxsw: i2c: Extend input parameters list of command APIVadim Pasternak
Extend input parameters list of command API in mlxsw_i2c_cmd() in order to support initialization commands. Up until now, only access commands were supported by I2C driver. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03mlxsw: i2c: Modify input parameter name in initialization APIVadim Pasternak
Change input parameter name "resource" to "res" in mlxsw_i2c_init() in order to align it with mlxsw_pci_init(). Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03mlxsw: i2c: Fix comment misspellingVadim Pasternak
Fix comment for mlxsw_i2c_write_cmd(). Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03mlxsw: core: Move resource query API to common locationVadim Pasternak
Move mlxsw_pci_resources_query() to a common location to allow reuse by the different drivers and over all the supported physical buses. Rename it to mlxsw_core_resources_query(). Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03mlxsw: minimal: Add ethtool supportVadim Pasternak
The minimal driver is chip independent and uses I2C bus for chip access. Its purpose is to support chassis management on systems equipped with Mellanox switch ASICs. For example from BMC (Board Management Controller) device. Expose a dummy netdev for each front panel port and implement basic ethtool operations to obtain QSFP/SFP module info through ethtool. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03mlxsw: minimal: Make structures and variables names shorterVadim Pasternak
Replace "mlxsw_minimal" by "mlxsw_m" in order to improve code readability. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03mlxsw: core: Move ethtool module callbacks to a common locationVadim Pasternak
Move the implementation of ethtool module callbacks - .get_module_info() and .get_module_eeprom() - to a common location to allow reuse by the different mlxsw drivers. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03net: phy: remove gen10g_no_soft_resetHeiner Kallweit
genphy_no_soft_reset and gen10g_no_soft_reset are both the same no-ops, one is enough. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03net: phy: don't export gen10g_read_statusHeiner Kallweit
gen10g_read_status is deprecated, therefore stop exporting it. We don't want to encourage anybody to use it. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03net: phy: remove gen10g_config_initHeiner Kallweit
ETHTOOL_LINK_MODE_10000baseT_Full_BIT is set anyway in the supported and advertising bitmap because it's part of PHY_10GBIT_FEATURES. And all users of gen10g_config_init use PHY_10GBIT_FEATURES. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03net: phy: remove gen10g_suspend and gen10g_resumeHeiner Kallweit
phy_suspend() and phy_resume() are no-ops anyway if no callback is defined. Therefore we don't need these stubs. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03net: phy: use genphy_c45_aneg_done in genphy_aneg_doneHeiner Kallweit
Now that we have it let's use genphy_c45_aneg_done() in phy_aneg_done(). Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03fsl/fman: Use vsprintf extension %pMJoe Perches
Make logging of an ethernet address more consistent with the rest of the kernel. Miscellanea: The %02hx use also did not quite match the u8 definition of addr though that did not actually matter given normal integer promotion rules. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03dpaa2-eth: add XDP_REDIRECT supportIoana Radulescu
Implement support for the XDP_REDIRECT action. The redirected frame is transmitted and confirmed on the regular Tx/Tx conf queues. Frame is marked with the "XDP" type in the software annotation, since it requires special treatment. We don't have good hardware support for TX batching, so the XDP_XMIT_FLUSH flag doesn't make a difference for now; ndo_xdp_xmit performs the actual Tx operation on the spot. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03dpaa2-eth: Add software annotation typesIoana Radulescu
We write different metadata information in the software annotation area of Tx frames, depending on frame type. Make this more explicit by introducing a type field and separate structures for single buffer and scatter-gather frames. Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03net: macb: Add support for suspend/resume with full power downHarini Katakam
When macb device is suspended and system is powered down, the clocks are removed and hence macb should be closed gracefully and restored upon resume. This patch does the same by switching off the net device, suspending phy and performing necessary cleanup of interrupts and BDs. Upon resume, all these are reinitialized again. Reset of macb device is done only when GEM is not a wake device. Even when gem is a wake device, tx queues can be stopped and ptp device can be closed (tsu clock will be disabled in pm_runtime_suspend) as wake event detection has no dependency on this. Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com> Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03net: macb: Add pm runtime supportHarini Katakam
Add runtime pm functions and move clock handling there. Add runtime PM calls to mdio functions to allow for active mdio bus. Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03net: macb: Support clock management for tsu_clkHarini Katakam
TSU clock needs to be enabled/disabled as per support in devicetree and it should also be controlled during suspend/resume (WOL has no dependency on this clock). Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03net: macb: Check MDIO state before read/write and use timeoutsHarini Katakam
Replace the while loop in MDIO read/write functions with a timeout. In addition, add a check for MDIO bus busy before initiating a new operation as well to make sure there is no ongoing MDIO operation. Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com> Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03net: dsa: microchip: add KSZ9893 switch supportTristram Ha
Add KSZ9893 switch support in KSZ9477 driver. This switch is similar to KSZ9477 except the ingress tail tag has 1 byte instead of 2 bytes, so KSZ9893 tagging will be used. The XMII register that governs how the host port communicates with the MAC also has different register definitions. Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02Merge tag 'mlx5-updates-2019-03-01' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5-updates-2019-03-01 This series adds multipath offload support and contains some small updates to mlx5 driver. Multipath offload support from Roi Dayan: We are going to track SW multipath route and related nexthops and reflect that as port affinity to the HW. 1) Some patches are preparation. 2) add the multipath mode and fib events handling. 3) add support to handle offload failure for net error, i.e. port down. 4) Small updates to match the behavior of multipath Two small updates from Eran Ben Elisha, 5) Make a function static 6) Update PCIe supported devices list. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02Merge branch 'for-upstream' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Johan Hedberg says: ==================== pull request: bluetooth-next 2019-03-02 Here's one more bluetooth-next pull request for the 5.1 kernel: - Added support for MediaTek MT7663U and MT7668U UART devices - Cleanups & fixes to the hci_qca driver - Fixed wakeup pin behavior for QCA6174A controller Please let me know if there are any issues pulling. Thanks. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2019-03-02Bluetooth: mediatek: add support for MediaTek MT7663U and MT7668U UART devicesSean Wang
This adds the support of enabling MT7663U and MT7668U Bluetooth function running on the top of btmtkuart driver. There are a few differences between MT766[3,8]U and MT7622 where MT766[3,8]U are standalone devices based on UART transport while MT7622 bluetooth is a built-in device on MediaTek SoC communicating with the host through BTIF serial transport. Thus, extra setup sequence is necessary for these standalone devices such as remote regulator and reset control via GPIO, baud rate changing handshake between the host and device and so on. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-03-02Bluetooth: hci_qca: Reduce delay after sending baudrate request for WCN3990Matthias Kaehlcke
The current 300ms delay after a baudrate change is extremely long. For WCN3990 it is sufficient to wait 10ms after the baudrate change request has been sent over the wire. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-03-02Merge tag 'wireless-drivers-next-for-davem-2019-03-01' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 5.1 Last set of patches. A new hardware support for mt76 otherwise quite normal. Major changes: mt76 * add driver for MT7603E/MT7628 ath10k * more preparation for SDIO support wil6210 * support up to 20 stations in AP mode ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02net: dsa: mv88e6xxx: Fix statistics on mv88e6161Andrew Lunn
Despite what the datesheet says, the silicon implements the older way of snapshoting the statistics. Change the op. Reported-by: Chris.Healy@zii.aero Tested-by: Chris.Healy@zii.aero Fixes: 0ac64c394900 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: set the GMAC, XLG MAC, XPCS and MPCS in reset when a port is downAntoine Tenart
This patch adds calls in the stop() helper to ensure both MACs and both PCS blocks are set in reset when the user manually sets a port down. This is done so that we have the exact same block reset states at boot time and when a port is set down. Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: set the XPCS and MPCS in reset when not usedAntoine Tenart
This patch sets both the XPCS and MPCS blocks in reset when they aren't used. This is done both at boot time and when reconfiguring a port mode. The advantage now is that only the PCS used is set out of reset when the port is configured (10GKR uses the MCPS while RXAUI uses the XPCS). Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: reset the MACs when reconfiguring a portAntoine Tenart
This patch makes sure both PPv2 MACs (GMAC + XLG MAC) are set in reset while a port is reconfigured. This is done so that we make sure a MAC is in a reset state when not used, as only one of the two will be set out of reset after the port is configured properly. Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: rework the XLG MAC reset handlingAntoine Tenart
This patch reworks the way the XLG MAC is set in reset: the XLG MAC is set in reset at probe time and taken out of this state only when used. The idea is to move forward a situation where only the blocks used are taken out of reset. This also has the effect to handle the GMAC and the XLG MAC in a similar way (the GMAC already is set in reset at boot time). Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: force the XLG MAC link up or down when not using in-bandAntoine Tenart
This patch force the XLG MAC link state in the phylink link_up() and link_down() helpers when not using in-band auto-negotiation. This mimics what's already done for the GMAC and follows what's advised in the phylink documentation. Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: only update the XLG configuration when neededAntoine Tenart
This patch improves the XLG configuration function, to only update the XLG configuration register when a change is needed. This helps not writing over and over the same XLG configuration each time phylink request the MAC to be configured. This mimics the GMAC configuration function. Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: always disable both MACs when disabling a portAntoine Tenart
This patch modifies the port_disable() helper to always disable both the GMAC and the XLG MAC when called. At boot time we do not know of a port was enabled in the firmware/bootloader, and if so what mode was used (hence which of the two MACs was used). This also help in implementing a logic where all blocks are disabled when not used, and only enabled regarding the current mode used on a given port. Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: some AN fields require the link to be down when updatedAntoine Tenart
The GMAC configuration helper modifies values in the auto-negotiation register. Some of its values require the port to be forced down when modifying their values. This patches fixes the check made on the bit to be updated in this register, so that the port is forced down when needed. This fix cases where some of those parameters were updated, but not taken into account, such as when using RGMII interfaces. Fixes: d14e078f23cc ("net: marvell: mvpp2: only reprogram what is necessary on mac_config") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: fix the computation of the RXQsAntoine Tenart
The patch fixes the computation of RXQs being used by the PPv2 driver, which is set depending on the PPv2 engine version and the queue mode used. There are three cases: - PPv2.1: 1 RXQ per CPU. - PPV2.2 with MVPP2_QDIST_MULTI_MODE: 1 RXQ per CPU. - PPv2.2 with MVPP2_QDIST_SINGLE_MODE: 1 RXQ is shared between the CPUs. The PPv2 engine supports a maximum of 32 queues per port. This patch adds a check so that we do not overstep this maximum. It appeared the calculation was broken for PPv2.1 engines since f8c6ba8424b0, as PPv2.1 ports ended up with a single RXQ while they needed 4. This patch fixes it. Fixes: f8c6ba8424b0 ("net: mvpp2: use only one rx queue per port per CPU") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: fix validate for PPv2.1Antoine Tenart
The Phylink validate function is the Marvell PPv2 driver makes a check on the GoP id. This is valid an has to be done when using PPv2.2 engines but makes no sense when using PPv2.1. The check done when using an RGMII interface makes sure the GoP id is not 0, but this breaks PPv2.1. Fixes it. Fixes: 0fb628f0f250 ("net: mvpp2: fix phylink handling of invalid PHY modes") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: reconfiguring the port interface is PPv2.2 specificAntoine Tenart
This patch adds a check on the PPv2 version in-use not to reconfigure the port mode when an interface is updated when using PPv2.1 as the functions called are PPv2.2 specific. Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: a port can be disabled even if we use the link IRQAntoine Tenart
We had a check in the mvpp2_mac_link_down() function (called by phylink) to avoid disabling the port when link interrupts are used. It turned out the interrupt can still be used with the port disabled. We can thus remove this check. Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: fix alignment of MVPP2_GMAC_CONFIG_MII_SPEED definitionAntoine Tenart
Cosmetic patch fix the alignment of the MVPP2_GMAC_CONFIG_MII_SPEED macro definition. Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: update the port documentation regarding the GoPAntoine Tenart
The Marvell PPv2 port structure stores the GoP id of a given port. This information is specific to PPv2.2, but cannot be used by PPv2.1. Update its comment to denote this specificity. Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01net: mvpp2: fix a typo in the headerAntoine Tenart
This cosmetic patch fixes a typo made in a comment in the Marvell PPv2 Ethernet driver header. Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-24 22:41:55 +0000