Age | Commit message (Collapse) | Author |
|
The existing devlink.c code is going to be extended to represent asic
device on a bus. As this is about more than just devlink,
rename the file. Do appropriate prefix renaming alongside with that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently there is one devlink instance created per network namespace.
That is quite odd considering the fact that devlink instance should
represent an ASIC. The following patches are going to move the devlink
instance even more down to a bus device, but until then, have one
devlink instance per netdevsim instance. Struct nsim_devlink is
introduced to hold fib setting.
The changes in the fib code are only related to holding the
configuration per devlink instance instead of network namespace.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a dependency of the subsequent patch, mode device registration to be
done earlier, directly in nsim_newlink().
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-04-25
Here's the main bluetooth-next pull request for the 5.2 kernel.
- Added support for Mediatek SDIO controllers
- Added support for Broadcom BCM2076B1 UART controller
- Added support for Marvel SD8987 chipset
- Fix buffer overflow bug in hidp protocol
- Various other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two easy cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"Just the usual assortment of small'ish fixes:
1) Conntrack timeout is sometimes not initialized properly, from
Alexander Potapenko.
2) Add a reasonable range limit to tcp_min_rtt_wlen to avoid
undefined behavior. From ZhangXiaoxu.
3) des1 field of descriptor in stmmac driver is initialized with the
wrong variable. From Yue Haibing.
4) Increase mlxsw pci sw reset timeout a little bit more, from Ido
Schimmel.
5) Match IOT2000 stmmac devices more accurately, from Su Bao Cheng.
6) Fallback refcount fix in TLS code, from Jakub Kicinski.
7) Fix max MTU check when using XDP in mlx5, from Maxim Mikityanskiy.
8) Fix recursive locking in team driver, from Hangbin Liu.
9) Fix tls_set_device_offload_Rx() deadlock, from Jakub Kicinski.
10) Don't use napi_alloc_frag() outside of softiq context of socionext
driver, from Ilias Apalodimas.
11) MAC address increment overflow in ncsi, from Tao Ren.
12) Fix a regression in 8K/1M pool switching of RDS, from Zhu Yanjun.
13) ipv4_link_failure has to validate the headers that are actually
there because RAW sockets can pass in arbitrary garbage, from Eric
Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add sanity checks in ipv4_link_failure()
net/rose: fix unbound loop in rose_loopback_timer()
rxrpc: fix race condition in rxrpc_input_packet()
net: rds: exchange of 8K and 1M pool
net: vrf: Fix operation not supported when set vrf mac
net/ncsi: handle overflow when incrementing mac address
net: socionext: replace napi_alloc_frag with the netdev variant on init
net: atheros: fix spelling mistake "underun" -> "underrun"
spi: ST ST95HF NFC: declare missing of table
spi: Micrel eth switch: declare missing of table
net: stmmac: move stmmac_check_ether_addr() to driver probe
netfilter: fix nf_l4proto_log_invalid to log invalid packets
netfilter: never get/set skb->tstamp
netfilter: ebtables: CONFIG_COMPAT: drop a bogus WARN_ON
Documentation: decnet: remove reference to CONFIG_DECNET_ROUTE_FWMARK
dt-bindings: add an explanation for internal phy-mode
net/tls: don't leak IV and record seq when offload fails
net/tls: avoid potential deadlock in tls_set_device_offload_rx()
selftests/net: correct the return value for run_afpackettests
team: fix possible recursive locking when add slaves
...
|
|
It allows some of the code to be simplified.
Tested on Turris Omnia.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vrf device is not able to change mac address now because lack of
ndo_set_mac_address. Complete this in case some apps need to do
this.
Reported-by: Hui Wang <wanghui104@huawei.com>
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm regression fixes from Dave Airlie:
"We interrupt your regularly scheduled drm fixes for a regression
special.
The first is for a fix in i915 that had unexpected side effects
fallout in the userspace X.org modesetting driver where X would no
longer start. I got tired of the nitpicking and issued a large hammer
on it. The X.org driver is buggy, but blackscreen regressions are
worse.
The second was an oversight that myself and Gerd should have noticed
better, Gerd is trying to fix this properly, but the regression is too
large to leave, even if the original behaviour is bad in some cases,
it's clearly bad to break a bunch of working use cases.
I'll likely have a regular fixes pull later, but I really wanted to
highlight these"
* tag 'drm-fixes-2019-04-24' of git://anongit.freedesktop.org/drm/drm:
Revert "drm/virtio: drop prime import/export callbacks"
Revert "drm/i915/fbdev: Actually configure untiled displays"
|
|
append
mlxsw currently does not support v6 gateways with v4 routes. Commit
19a9d136f198 ("ipv4: Flag fib_info with a fib_nh using IPv6 gateway")
prevents a route from being added, but nothing stops the replace or
append. Add a catch for them too.
$ ip ro add 172.16.2.0/24 via 10.99.1.2
$ ip ro replace 172.16.2.0/24 via inet6 fe80::202:ff:fe00:b dev swp1s0
Error: mlxsw_spectrum: IPv6 gateway with IPv4 route is not supported.
$ ip ro append 172.16.2.0/24 via inet6 fe80::202:ff:fe00:b dev swp1s0
Error: mlxsw_spectrum: IPv6 gateway with IPv4 route is not supported.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netdev variant is usable on any context since it disables interrupts.
The napi variant of the call should only be used within softirq context.
Replace napi_alloc_frag on driver init with the correct netdev_alloc_frag
call
Changes since v1:
- Adjusted commit message
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Fixes: 4acb20b46214 ("net: socionext: different approach on DMA")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are spelling mistakes in structure elements, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the R-Car Gen3 Hardware Manual Rev 1.50 of Nov 30, 2018, the
TX clock internal delay mode isn't supported on R-Car E3 (r8a77990) or D3
(r8a77995). And by extension it is also not supported by RZ/G2E (r9a774c0).
This matches all ES versions of the affected SoCs as it is
not clear if this problem will be resolved in newer chips.
This can be revisited, as necessary.
This patch does not error-out if PHY_INTERFACE_MODE_RGMII_ID or
PHY_INTERFACE_MODE_RGMII_TXID are used on SoCs where TX clock delay
mode is not supported as there is a risk of introducing a regression
when used in conjunction with older DT blobs present in the field.
Rather, a warning is logged in such cases.
Based on work by Kazuya Mizuguchi.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pointers should be printed with %p or %px rather than
cast to (u_long) and printed with %lx.
Change %lx to %p to print the pointer.
Change %lx to %pad to print the dma_addr_t.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pointers should be printed with %p or %px rather than
cast to (u_long) type and printed with %lX.
As the function seems to be for debug purpose.
Change %lX to %px to print the pointer value.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch does more harm than good, as it breaks both Xwayland and
gnome-shell with X11.
Xwayland requires DRI3 & DRI3 requires PRIME.
X11 crash for obscure double-free reason which are hard to debug
(starting X11 by hand doesn't trigger the crash).
I don't see an apparent problem implementing those stub prime
functions, they may return an error at run-time, and it seems to be
handled fine by GNOME at least.
This reverts commit b318e3ff7ca065d6b107e424c85a63d7a6798a69.
[airlied:
This broke userspace for virtio-gpus, and regressed things from DRI3 to DRI2.
This brings back the original problem, but it's better than regressions.]
Fixes: b318e3ff7ca065d6b107e424c85a63d7a6798a ("drm/virtio: drop prime import/export callbacks")
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This reverts commit d179b88deb3bf6fed4991a31fd6f0f2cad21fab5.
This commit is documented to break userspace X.org modesetting driver in certain configurations.
The X.org modesetting userspace driver is broken. No fixes are available yet. In order for this patch to be applied it either needs a config option or a workaround developed.
This has been reported a few times, saying it's a userspace problem is clearly against the regression rules.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109806
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: <stable@vger.kernel.org> # v3.19+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-04-22
This series includes updates to mlx5e driver RX data path and some
significant XDP RX/TX improvements to overcome/mitigate HW and PCIE
bottlenecks.
From Tariq:
1) Some Enhancements in rq->flags
2) Stabilize RX packet rate (on Striding RQ) with
multiple outstanding UMR posts
In this patch, we add support for multiple outstanding UMR posts,
to allow faster gap closure between consuming MPWQEs and reposting
them back into the WQ.
Performance test:
As expected, huge improvement in large-scale (48 cores).
xdp_redirect_map, 64B UDP multi-stream.
Redirect from ConnectX-5 100Gbps to ConnectX-6 100Gbps.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz.
Before: Unstable, 7 to 30 Mpps
After: Stable, at 70.5 Mpps
From Shay:
3) XDP, Inline small packets into the TX MPWQE in XDP xmit flow
Upon high packet rate with multiple CPUs TX workloads, much of the HCA's
resources are spent on prefetching TX descriptors, thus affecting
transmission rates.
This patch comes to mitigate this problem by moving some workload to the
CPU and reducing the HW data prefetch overhead for small packets (<= 256B).
When forwarding packets with XDP, a packet that is smaller
than a certain size (set to ~256 bytes) would be sent inline within
its WQE TX descrptor (mem-copied), when the hardware tx queue is congested
beyond a pre-defined water-mark.
Performance:
Tested packet rate for UDP 64Byte multi-stream
over two dual port ConnectX-5 100Gbps NICs.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
* Tested with hyper-threading disabled
XDP_TX:
| | before | after | |
| 24 rings | 51Mpps | 116Mpps | +126% |
| 1 ring | 12Mpps | 12Mpps | same |
XDP_REDIRECT:
** Below is the transmit rate, not the redirection rate
which might be larger, and is not affected by this patch.
| | before | after | |
| 32 rings | 64Mpps | 92Mpps | +43% |
| 1 ring | 6.4Mpps | 6.4Mpps | same |
As we can see, feature significantly improves scaling, without
hurting single ring performance.
From Maxim:
4) Some trivial refactoring and code improvements prior to a larger series
to support AF_XDP.
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qca_set_baudrate() calls serdev_device_wait_until_sent() assuming that
the HCI is always associated with a serdev device. This isn't true for
ROME controllers instantiated through ldisc, where the call causes a
crash due to a NULL pointer dereferentiation. Only call the function
when we have a serdev device. The timeout for ROME devices at the end
of qca_set_baudrate() is long enough to be reasonably sure that the
command was sent.
Fixes: fa9ad876b8e0 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990")
Reported-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reported-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Rocky Liao <rjliao@codeaurora.org>
Tested-by: Rocky Liao <rjliao@codeaurora.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Create a #define for the timeout of mlx5e_wait_for_min_rx_wqes to
clarify the meaning of a magic number.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Remove the no longer used page_reuse stat of RQs.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
mlx5e_trigger_irq posts a NOP to the ICO SQ just to trigger an IRQ and
enter the NAPI poll on the right CPU according to the affinity. Use it
in mlx5e_activate_rq.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
mdev is unused in mlx5e_rx_is_linear_skb.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
mlx5e_mpwqe_get_log_rq_size calculates the number of WQEs (N) based on
the requested number of frames in the RQ (F) and the number of packets
per WQE (P). It ensures that N is not less than the minimum number of
WQEs in an RQ (N_min). Arithmetically, it means that F / P >= N_min
should be true. This function deals with logarithms, so it should check
that log(F) - log(P) >= log(N_min). However, if F < P, this expression
will cause an unsigned underflow. Check log(F) >= log(P) + log(N_min)
instead.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This commit moves the parameter calculation functions to a separate file
for better modularity and code sharing with future features.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If the channels fail to reopen after setting an XDP program, return the
error code instead of 0. A proper fix is still needed, as now any error
while reopening the channels brings the interface down. This patch only
adds error reporting.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
params is unused in mlx5e_init_di_list.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Upon high packet rate with multiple CPUs TX workloads, much of the HCA's
resources are spent on prefetching TX descriptors, thus affecting
transmission rates.
This patch comes to mitigate this problem by moving some workload to the
CPU and reducing the HW data prefetch overhead for small packets (<= 256B).
When forwarding packets with XDP, a packet that is smaller
than a certain size (set to ~256 bytes) would be sent inline within
its WQE TX descrptor (mem-copied), when the hardware tx queue is congested
beyond a pre-defined water-mark.
This is added to better utilize the HW resources (which now makes
one less packet data prefetch) and allow better scalability, on the
account of CPU usage (which now 'memcpy's the packet into the WQE).
To load balance between HW and CPU and get max packet rate, we use
watermarks to detect how much the HW is congested and move the work
loads back and forth between HW and CPU.
Performance:
Tested packet rate for UDP 64Byte multi-stream
over two dual port ConnectX-5 100Gbps NICs.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
* Tested with hyper-threading disabled
XDP_TX:
| | before | after | |
| 24 rings | 51Mpps | 116Mpps | +126% |
| 1 ring | 12Mpps | 12Mpps | same |
XDP_REDIRECT:
** Below is the transmit rate, not the redirection rate
which might be larger, and is not affected by this patch.
| | before | after | |
| 32 rings | 64Mpps | 92Mpps | +43% |
| 1 ring | 6.4Mpps | 6.4Mpps | same |
As we can see, feature significantly improves scaling, without
hurting single ring performance.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This counter tracks how many TX MPWQE sessions are started in XDP SQ
in XDP TX/REDIRECT flow. It counts per-channel and global stats.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The XDP redirect flush indication belongs to the receive queue,
not to its XDP send queue.
For this, use a new bit on rq->flags.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Values in enum mlx5e_rq_flag are used as bit indixes.
Intention was to use them with no BIT(i) wrapping.
No functional bug fix here, as the same (shifted)flag bit
is used for all set, test, and clear operations.
Fixes: 121e89275471 ("net/mlx5e: Refactor RQ XDP_TX indication")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The buffers mapping of the Multi-Packet WQEs (of Striding RQ)
is done via UMR posts, one UMR WQE per an RX MPWQE.
A single MPWQE is capable of serving many incoming packets,
usually larger than the budget of a single napi cycle.
Hence, posting a single UMR WQE per napi cycle (and handling its
completion in the next cycle) works fine in many common cases,
but not always.
When an XDP program is loaded, every MPWQE is capable of serving less
packets, to satisfy the packet-per-page requirement.
Thus, for the same number of packets more MPWQEs (and UMR posts)
are needed (twice as much for the default MTU), giving less latency
room for the UMR completions.
In this patch, we add support for multiple outstanding UMR posts,
to allow faster gap closure between consuming MPWQEs and reposting
them back into the WQ.
For better SW and HW locality, we combine the UMR posts in bulks of
(at least) two.
This is expected to improve packet rate in high CPU scale.
Performance test:
As expected, huge improvement in large-scale (48 cores).
xdp_redirect_map, 64B UDP multi-stream.
Redirect from ConnectX-5 100Gbps to ConnectX-6 100Gbps.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz.
Before: Unstable, 7 to 30 Mpps
After: Stable, at 70.5 Mpps
No degradation in other tested scenarios.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
|
|
Add support for VSC8514 in Microsemi driver (mscc.c)
with more features.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X, can communicate with the MAC via QSGMII.
The MAC interface protocol for each port within QSGMII can
be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is
connecting to supports this functionality.
VSC8514 also supports SGMII MAC-side autonegotiation on each individual
port, downshifting, can set the blinking pattern of each of its 4 LEDs,
SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection.
This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T,
QSGMII link with the MAC, downshifting, HP Auto-MDIX detection
and blinking pattern for its 4 LEDs.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
After this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
alias: of:N*T*Cst,st95hfC*
alias: of:N*T*Cst,st95hf
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
alias: of:N*T*Cmicrel,ksz8795C*
alias: of:N*T*Cmicrel,ksz8795
alias: of:N*T*Cmicrel,ksz8864C*
alias: of:N*T*Cmicrel,ksz8864
alias: of:N*T*Cmicrel,ks8995C*
alias: of:N*T*Cmicrel,ks8995
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default m88e151x LED configuration is 0x1177, used LED[0]
for 1000M link, LED[1] for 100M link, and LED[2] for active.
But for some boards, which use LED[0] for link, and LED[1] for
active, prefer to be 0x1040. To be compatible with this case,
this patch defines a new dev_flag, and set it before connect
phy in HNS3 driver. When phy initializing, using the new
LED configuration if this dev_flag is set.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables enough time to ROME controller to bootup
after we bring the enable pin out of reset.
Fixes: 05ba533c5c11 ("Bluetooth: hci_qca: Add serdev support").
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Rocky Liao <rjliao@codeaurora.org>
Tested-by: Rocky Liao <rjliao@codeaurora.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The code path for Macs goes through bcm_apple_get_resources(), which
skips over the code that sets up the regulator supplies. As a result,
the call to regulator_bulk_enable() / regulator_bulk_disable() results
in a NULL pointer dereference.
This was reported on the kernel.org Bugzilla, bug 202963.
Unbreak Broadcom Bluetooth support on Intel Macs by checking if the
supplies were set up before enabling or disabling them.
The same does not need to be done for the clocks, as the common clock
framework API checks for NULL pointers.
Fixes: 75d11676dccb ("Bluetooth: hci_bcm: Add support for regulator supplies")
Cc: <stable@vger.kernel.org> # 5.0.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add the device ID for the BT/FM/GPS combo chip BCM2076 (rev B1)
used in the AMPAK AP6476 WiFi/BT/FM/GPS module.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The BCM43341B has the default MAC address 43:34:1B:00:1F:AC if none
is given. This address was found when enabling Bluetooth on multiple
Intel Edison modules. It also contains the sequence 43341B, the name
the chip identifies itself as. Using the same BD_ADDR is problematic
when having multiple Intel Edison modules in each others range.
The default address also has the LAA (locally administered address)
bit set which prevents a BNEP device from being created, needed for
BT tethering.
Add this to the list of black listed default MAC addresses and let
the user configure a valid one using f.i.
`btmgmt -i hci0 public-addr xx:xx:xx:xx:xx:xx`
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds support for Marvell 88W8987 chipset with SDIO interface.
Register offsets and supported feature flags are updated. The corresponding
firmware image file shall be "mrvl/sd8987_uapsta.bin".
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add runtime PM support to btmtksdio. With this way, there will be the
benefit of the device entering the more power saving state once it is
been a while data traffic is idle.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Accumulate hdev->stat.byte_rx only for valid packets as btmtkuart doing.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add a register bit definition about CHLPCR bit 8 because the bit is quite
different in the meaning between reading and writing that bit.
The patch adds a definition particularly for the bit read to avoid the
confusion about using write definition to read the bit.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
bt_dev logging macros already include a newline at each output
so drop these unnecessary additional newlines in the driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
There is a spelling mistake in a BT_DBG debug message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fixed warning: incorrect type in assignment reported by kbuild test robot.
The detailed warning is shown as below.
make ARCH=x86_64 allmodconfig
make C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__'
All warnings (new ones prefixed by >>):
btmtkuart.c:671:18: sparse: warning: incorrect type in assignment
(different base types)
btmtkuart.c:671:18: sparse: expected unsigned int [usertype] baudrate
btmtkuart.c:671:18: sparse: got restricted __le32 [usertype]
sparse warnings: (new ones prefixed by >>)
btmtkuart.c:671:18: sparse: warning: incorrect type in assignment
(different base types)
btmtkuart.c:671:18: sparse: expected unsigned int [usertype] baudrate
btmtkuart.c:671:18: sparse: got restricted __le32 [usertype]
vim +671 drivers/bluetooth/btmtkuart.c
659
660 static int btmtkuart_change_baudrate(struct hci_dev *hdev)
661 {
662 struct btmtkuart_dev *bdev = hci_get_drvdata(hdev);
663 struct btmtk_hci_wmt_params wmt_params;
664 u32 baudrate;
665 u8 param;
666 int err;
667
668 /* Indicate the device to enter the probe state the host is
669 * ready to change a new baudrate.
670 */
> 671 baudrate = cpu_to_le32(bdev->desired_speed);
672 wmt_params.op = MTK_WMT_HIF;
Fixes: 22eaf6c9946a ("Bluetooth: mediatek: add support for MediaTek MT7663U and MT7668U UART devices")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fixed all the below warnings. They would probably cause the following
error handling path would use the uninitialized value and then produce
unexpected behavior.
drivers/bluetooth/btmtksdio.c:470:2: warning: ‘old_len’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
print_hex_dump(KERN_ERR, "err sdio rx: ", DUMP_PREFIX_NONE, 4, 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
old_data, old_len, true);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtksdio.c:376:15: note: ‘old_len’ was declared here
unsigned int old_len;
^~~~~~~
drivers/bluetooth/btmtksdio.c:470:2: warning: ‘old_data’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
print_hex_dump(KERN_ERR, "err sdio rx: ", DUMP_PREFIX_NONE, 4, 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
old_data, old_len, true);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtksdio.c:375:17: note: ‘old_data’ was declared here
unsigned char *old_data;
^~~~~~~~
v2: Remove old_len and old_data because the error path for sdio_readsb also
seems wrong. And change the prefix from "mediatek" to "btmtksdio".
Fixes: d74eef2834b5 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|