| Age | Commit message (Collapse) | Author |
|---|
|
Since the RX path on USB devices is handled in process context we can
use GFP_KERNEL for RX buffer allocation. This should reduce the
likelihood of allocation failures.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Tested-By: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We're already using BBP for values > 128. Make that explicit and allow
debugfs access.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch supports Avastar 88W8797 chipset with USB interface.
The corresponding firmware image file is located at:
"mrvl/usb8797_uapsta.bin"
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The current code unconditionally reads the target
power values for all modes from the EEPROM. However
In 'ar9003_hw_set_power_per_rate_table' the regulatory
caps are applied only on a mode specific subset of the
power values.
The reported TX power level is calculated from the
maximum of the power values. Because some of these
values are uncapped in certain cases, the reported
TX power will be wrong.
On the older chipset, we don't have such problems
because only the mode specific subset of the power
levels are retrieved from the EEPROM on those. Do
the same for the AR9003 chips to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Daniel Drake <dsd@laptop.org>
Tested-by: Dan Williams <dcbw@redhat.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes two compile warnings, and removes a useless
cast when assigning the 'sc' variable.
Reported-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
found in 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO
RT3070:
(0x2019,0x5201) Planex Communications, Inc. RT8070
(0x7392,0x4085) 2L Central Europe BV 8070
7392 is Edimax
RT35xx:
(0x1690,0x0761) Askey
was Fujitsu Stylistic 550, but 1690 is Askey
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
They were taken from ralink drivers:
2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO
2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO
0x1eda,0x2210 RT3070 Airties
0x083a,0xb511 RT3370 Panasonic
0x0471,0x20dd RT3370 Philips
0x1690,0x0764 RT35xx Askey
0x0df6,0x0065 RT35xx Sitecom
0x0df6,0x0066 RT35xx Sitecom
0x0df6,0x0068 RT35xx Sitecom
0x2001,0x3c1c RT5370 DLink
0x2001,0x3c1d RT5370 DLink
2001 is D-Link not Alpha
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It can be moved to iwl-dev.h since it is op_mode specific.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Having cmd[], meta[] and skbs[] as separate arrays
in the TX queue structure is cache inefficient as
we need the data for a given entry together.
To improve this, create an array with these three
members (allocate meta as part of that struct) so
we have the data we need together located together
improving cache footprint.
The downside is that we need to allocate a lot of
memory in one chunk, about 10KiB (on 64-bit) which
isn't very efficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
This allows not to notify the transport about aggregation stopped
while aggregation haven't been started.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Remove declaration of iwl_alloc_traffic_mem from iwl-agn.h,
from methods that was exposed to support MVM.
MVM doesn't have to use this declaration.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Please merge this with "iwlwifi: op_mode holds its pointer
to the config"
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Changed disable calibration bit field defines to enum.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
It is not needed any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Each modules will hold a pointer to struct device instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Instead of using the shared area that we be killed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Instead of using the shared area that we be killed.
Remove the pointer to config from shared since it is not
used any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Instead of using the shared area that will be killed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Instead of using the shared area that we be killed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Instead of using the shared area that we be killed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
The driver layer now holds a pointer to the transport,
and shrd->drv is not needed any more, so kill it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
We get two timing related fields for each bss from firmware in scan
results.
1) timestamp - Actual timestamp information in probe response/beacon
2) network_tsf - firmware's TSF value at the time the beacon or probe
response was received.
Both are needed while associating by firmware.
The patch takes care of following things.
1) We should pass "timestamp" to cfg80211_inform_bss(), but currently
"network_tsf" is being provided. This error is corrected here.
2) Rename "network_tsf" to "fw_tsf"
3) Make use of u64 variable instead of an array of u8/u32 to save
parsed "timestamp" information.
4) Use timestamp provided to stack in scan results using
cfg80211_inform_bss() while associating. (bss->tsf)
5) Allocate space to save fw_tsf in "priv" of cfg80211_bss
and retrieve it while associating.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rearrange some code to save extra parameters to the functions.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
As described at
http://article.gmane.org/gmane.linux.kernel.wireless.general/86084
libertas is taking a long time to load because it loads firmware
during module loading.
Add a new API for interface drivers to load their firmware
asynchronously. The same semantics of the firmware table are followed
like before.
Interface drivers will be converted in follow-up patches, then we can
remove the old, synchronous firmware loading function.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
These simple sanity check avoids extra complexity in error paths when
moving to asynchronous firmware loading (which means the device may fail to
init some time after its creation).
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove the ability to pass module parameters with firmware filenames
for USB and SDIO interfaces.
Remove the ability to pass custom "user" filenames to lbs_get_firmware().
Remove the ability to reprogram internal device memory with a different
firmware from the USB driver (we don't know of any users), and simplify
the OLPC firmware loading quirk to simply placing the OLPC firmware
at the top of the list (we don't know of any users other than OLPC).
Move lbs_get_firmware() into its own file.
These simplifications should have no real-life effect but make the
upcoming transition to asynchronous firmware loading considerably less
painful.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There are connection stalls or very poor throughputs with rt2800
hardware using 802.11n in AP mode since patch "mac80211: retry sending
failed BAR frames later instead of tearing down aggr"[1][2].
Since rt2800 hardware is not able to correctly report the tx status of
BAR frames, this patch removes as workaround the existing error handling
on AP side, which lets mac80211 send a BAR when an AMPDU subframe fails.
As a result, most wifi clients (aside from Intel STAs on Windows)
instead will timeout now the reorder buffer and request the lost frame
again.
The correct solution would be, to tear down BA session on AP side.
This patch was born on the basis of "[RFT] rt2x00: Tear down BA
session on QoS frame failure"[3].
Thanks to Helmut Schaa for his support!
[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/83297/focus=83304
[2] http://git.kernel.org/?p=linux/kernel/git/linville/wireless-testing.git;a=commit;h=f0425beda4d404a6e751439b562100b902ba9c98
[3] http://thread.gmane.org/gmane.linux.drivers.rt2x00.user/569
Signed-off-by: Andreas Hartmann <andihartmann@01019freenet.de>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The FBIN2FREQ macro and the ath9k_hw_fbin2freq function
does the same thing. Remove the macro, and use the inline
function instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Both eeprom.c and ar9003_eeprom.c has an indentical
'ath9k_hw_fbin2freq' function. Move the function to
a common place and remove the duplicates.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The existing constants are used for reduction/increase
tx power level on devices with 2x2 and 3x3 chainmask.
Both reduction and increase must use the same value, so
it makes no sense to use separate constants for them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add a corresponding leave call on error failure.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The command strings are needed through the layers for
debug and error messages, but can differ with opmode.
As a result, we need to give the command names to the
transport layer as configuration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Having a u32 before a potential 64-bit value is
not very efficient, move it last.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
To support hybrid state of MVM op_mode, most of the functioanallity
will be done using DVM functions.
When MVM will have independant live, the declarations will be removed
and the functions will be static back.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Implement mapping of channel to TX power channel group,
for sending channel specific data before add context.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Add a variable for disabling specific calibrations.
Merged old variables for calibrations disabling.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Set size of firmware section in mvm bundle format.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
The declaration isn't needed as the struct is only
used in code that includes the right header file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
The code has been changed, move the definitions to the proper file
being used by the code.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
This register is used to enable some debug mechanisms.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
The HCMD_ACTIVE bit is only used in trans.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
When WiMax takes over the RF, inform the op_mode.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
