Age | Commit message (Collapse) | Author |
|
The xilinx_can driver assumes that the TXOK interrupt only clears after
it has been acknowledged as many times as there have been successfully
sent frames.
However, the documentation does not mention such behavior, instead
saying just that the interrupt is cleared when the clear bit is set.
Similarly, testing seems to also suggest that it is immediately cleared
regardless of the amount of frames having been sent. Performing some
heavy TX load and then going back to idle has the tx_head drifting
further away from tx_tail over time, steadily reducing the amount of
frames the driver keeps in the TX FIFO (but not to zero, as the TXOK
interrupt always frees up space for 1 frame from the driver's
perspective, so frames continue to be sent) and delaying the local echo
frames.
The TX FIFO tracking is also otherwise buggy as it does not account for
TX FIFO being cleared after software resets, causing
BUG!, TX FIFO full when queue awake!
messages to be output.
There does not seem to be any way to accurately track the state of the
TX FIFO for local echo support while using the full TX FIFO.
The Zynq version of the HW (but not the soft-AXI version) has watermark
programming support and with it an additional TX-FIFO-empty interrupt
bit.
Modify the driver to only put 1 frame into TX FIFO at a time on soft-AXI
and 2 frames at a time on Zynq. On Zynq the TXFEMP interrupt bit is used
to detect whether 1 or 2 frames have been sent at interrupt processing
time.
Tested with the integrated CAN on Zynq-7000 SoC. The 1-frame-FIFO mode
was also tested.
An alternative way to solve this would be to drop local echo support but
keep using the full TX FIFO.
v2: Add FIFO space check before TX queue wake with locking to
synchronize with queue stop. This avoids waking the queue when xmit()
had just filled it.
v3: Keep local echo support and reduce the amount of frames in FIFO
instead as suggested by Marc Kleine-Budde.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The xilinx_can driver contains no mechanism for propagating recovery
from CAN_STATE_ERROR_WARNING and CAN_STATE_ERROR_PASSIVE.
Add such a mechanism by factoring the handling of
XCAN_STATE_ERROR_PASSIVE and XCAN_STATE_ERROR_WARNING out of
xcan_err_interrupt and checking for recovery after RX and TX if the
interface is in one of those states.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If the device gets into a state where RXNEMP (RX FIFO not empty)
interrupt is asserted without RXOK (new frame received successfully)
interrupt being asserted, xcan_rx_poll() will continue to try to clear
RXNEMP without actually reading frames from RX FIFO. If the RX FIFO is
not empty, the interrupt will not be cleared and napi_schedule() will
just be called again.
This situation can occur when:
(a) xcan_rx() returns without reading RX FIFO due to an error condition.
The code tries to clear both RXOK and RXNEMP but RXNEMP will not clear
due to a frame still being in the FIFO. The frame will never be read
from the FIFO as RXOK is no longer set.
(b) A frame is received between xcan_rx_poll() reading interrupt status
and clearing RXOK. RXOK will be cleared, but RXNEMP will again remain
set as the new message is still in the FIFO.
I'm able to trigger case (b) by flooding the bus with frames under load.
There does not seem to be any benefit in using both RXNEMP and RXOK in
the way the driver does, and the polling example in the reference manual
(UG585 v1.10 18.3.7 Read Messages from RxFIFO) also says that either
RXOK or RXNEMP can be used for detecting incoming messages.
Fix the issue and simplify the RX processing by only using RXNEMP
without RXOK.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The xilinx_can driver performs a software reset when an RX overrun is
detected. This causes the device to enter Configuration mode where no
messages are received or transmitted.
The documentation does not mention any need to perform a reset on an RX
overrun, and testing by inducing an RX overflow also indicated that the
device continues to work just fine without a reset.
Remove the software reset.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
MCAN message ram should only be accessed once clocks are enabled.
Therefore, move the call to parse/init the message ram to after
clocks are enabled.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
pm_runtime_get_sync() returns a 1 if the state of the device is already
'active'. This is not a failure case and should return a success.
Therefore fix error handling for pm_runtime_get_sync() call such that
it returns success when the value is 1.
Also cleanup the TODO for using runtime PM for sleep mode as that is
implemented.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
of_iomap() can return NULL so that return needs to be checked and NULL
treated as failure. While at it also take care of the missing
of_node_put() in the error path.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: commit afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
checking can.ctrlmode
Inside m_can_chip_config(), when setting up the new value of the CCCR,
the CCCR_NISO bit is not cleared like the others, CCCR_TEST, CCCR_MON,
CCCR_BRSE and CCCR_FDOE, before checking the can.ctrlmode bits for
CAN_CTRLMODE_FD_NON_ISO.
This way once the controller was configured for CAN_CTRLMODE_FD_NON_ISO,
this mode could never be cleared again.
This fix is only relevant for controllers with version 3.1.x or 3.2.x.
Older versions do not support NISO.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The DMA logic in firmwares < v3.3.0 embedded in the PCAN-PCIe FD cards
family is not capable of handling a mix of 32-bit and 64-bit logical
addresses. If the board is equipped with 2 or 4 CAN ports, then such a
situation might lead to a PCIe Bus Error "Malformed TLP" packet
as well as "irq xx: nobody cared" issue.
This patch adds a workaround that requests only 32-bit DMA addresses
when these might be allocated outside of the 4 GB area.
This issue has been fixed in firmware v3.3.0 and next.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The dispatcher and the executer process the parse nodes During table
load. Error status from the evaluation confuses the AML parser. This
results in the parser failing to complete parsing of the current
scope op which becomes problematic. For the incorrect AML below, _ADR
never gets created.
definition_block(...)
{
Scope (\_SB)
{
Device (PCI0){...}
Name (OBJ1, 0x0)
OBJ1 = PCI0 + 5 // Results in an operand error.
} // \_SB not closed
// parser looks for \_SB._SB.PCI0, results in AE_NOT_FOUND error
// Entire scope block gets skipped.
Scope (\_SB.PCI0)
{
Name (_ADR, 0x0)
}
}
Fix the above error by properly completing the initial \_SB scope
after an error by clearing errors that occur during table load. In
the above case, this means that OBJ1 = PIC0 + 5 is skipped.
Fixes: 5088814a6e93 (ACPICA: AML parser: attempt to continue loading table after error)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200363
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull NVMe fixes from Christoph Hellwig:
- fix a regression in 4.18 that causes a memory leak on probe failure
(Keith Bush)
- fix a deadlock in the passthrough ioctl code (Scott Bauer)
- don't enable AENs if not supported (Weiping Zhang)
- fix an old regression in metadata handling in the passthrough ioctl
code (Roland Dreier)
* tag 'nvme-for-4.18' of git://git.infradead.org/nvme:
nvme: fix handling of metadata_len for NVME_IOCTL_IO_CMD
nvme: don't enable AEN if not supported
nvme: ensure forward progress during Admin passthru
nvme-pci: fix memory leak on probe failure
|
|
Pull vfs fixes from Al Viro:
"Fix several places that screw up cleanups after failures halfway
through opening a file (one open-coding filp_clone_open() and getting
it wrong, two misusing alloc_file()). That part is -stable fodder from
the 'work.open' branch.
And Christoph's regression fix for uapi breakage in aio series;
include/uapi/linux/aio_abi.h shouldn't be pulling in the kernel
definition of sigset_t, the reason for doing so in the first place had
been bogus - there's no need to expose struct __aio_sigset in
aio_abi.h at all"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
aio: don't expose __aio_sigset in uapi
ocxlflash_getfile(): fix double-iput() on alloc_file() failures
cxl_getfile(): fix double-iput() on alloc_file() failures
drm_mode_create_lease_ioctl(): fix open-coded filp_clone_open()
|
|
Prevent drivers from building on PPC32 if they use isa_bus_to_virt(),
isa_virt_to_bus(), or isa_page_to_bus(), which are not available and
thus cause build errors.
../drivers/net/ethernet/3com/3c515.c: In function 'corkscrew_open':
../drivers/net/ethernet/3com/3c515.c:824:9: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/lance.c: In function 'lance_rx':
../drivers/net/ethernet/amd/lance.c:1203:23: error: implicit declaration of function 'isa_bus_to_virt'; did you mean 'bus_to_virt'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/ni65.c: In function 'ni65_init_lance':
../drivers/net/ethernet/amd/ni65.c:585:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
../drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously only the neighbour state was checked to decide if an offloaded
entry should be removed. However, there can be situations when the entry
is dead but still marked as valid. This can lead to dead entries not
being removed from fw tables or even incorrect data being added.
Check the entry dead bit before deciding if it should be added to or
removed from fw neighbour tables.
Fixes: 8e6a9046b66a ("nfp: flower vxlan neighbour offload")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Problem:
In vxlan_newlink, a default fdb entry is added before register_netdev.
The default fdb creation function also notifies user-space of the
fdb entry on the vxlan device which user-space does not know about yet.
(RTM_NEWNEIGH goes before RTM_NEWLINK for the same ifindex).
This patch fixes the user-space netlink notification ordering issue
with the following changes:
- decouple fdb notify from fdb create.
- Move fdb notify after register_netdev.
- Call rtnl_configure_link in vxlan newlink handler to notify
userspace about the newlink before fdb notify and
hence avoiding the user-space race.
Fixes: afbd8bae9c79 ("vxlan: add implicit fdb entry for default destination")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new option do_notify to vxlan_fdb_destroy to make
sending netlink notify optional. Used by a later patch.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Add new vxlan_fdb_alloc helper
- rename existing vxlan_fdb_create into vxlan_fdb_update:
because it really creates or updates an existing
fdb entry
- move new fdb creation into a separate vxlan_fdb_create
Main motivation for this change is to introduce the ability
to decouple vxlan fdb creation and notify, used in a later patch.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Got crash report with following backtrace:
BUG: unable to handle kernel paging request at ffff8801869daffe
RIP: 0010:[<ffffffff816429c4>] [<ffffffff816429c4>] ip6_finish_output2+0x394/0x4c0
RSP: 0018:ffff880186c83a98 EFLAGS: 00010283
RAX: ffff8801869db00e ...
[<ffffffff81644cdc>] ip6_finish_output+0x8c/0xf0
[<ffffffff81644d97>] ip6_output+0x57/0x100
[<ffffffff81643dc9>] ip6_forward+0x4b9/0x840
[<ffffffff81645566>] ip6_rcv_finish+0x66/0xc0
[<ffffffff81645db9>] ipv6_rcv+0x319/0x530
[<ffffffff815892ac>] netif_receive_skb+0x1c/0x70
[<ffffffffc0060bec>] atl1c_clean+0x1ec/0x310 [atl1c]
...
The bad access is in neigh_hh_output(), at skb->data - 16 (HH_DATA_MOD).
atl1c driver provided skb with no headroom, so 14 bytes (ethernet
header) got pulled, but then 16 are copied.
Reserve NET_SKB_PAD bytes headroom, like netdev_alloc_skb().
Compile tested only; I lack hardware.
Fixes: 7b7017642199 ("atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
free_irq() waits until all handlers for this IRQ have completed. As the
relevant handler (mv88e6xxx_g1_irq_thread_fn()) takes the chip's reg_lock
it might never return if the thread calling free_irq() holds this lock.
For the same reason kthread_cancel_delayed_work_sync() in the polling case
must not hold this lock.
Also first free the irq (or stop the worker respectively) such that
mv88e6xxx_g1_irq_thread_work() isn't called any more before the irq
mappings are dropped in mv88e6xxx_g1_irq_free_common() to prevent the
worker thread to call handle_nested_irq(0) which results in a NULL-pointer
exception.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
- Fix interrupt type on ethernet switch for i.MX-based RDU2
- GPC on i.MX exposed too large a register window which resulted in
userspace being able to crash the machine.
- Fixup of bad merge resolution moving GPIO DT nodes under pinctrl on
droid4.
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: imx6: RDU2: fix irq type for mv88e6xxx switch
soc: imx: gpc: restrict register range for regmap access
ARM: dts: omap4-droid4: fix dts w.r.t. pwm
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two regression fixes, one for xmon disassembly formatting and the
other to fix the E500 build.
Two commits to fix a potential security issue in the VFIO code under
obscure circumstances.
And finally a fix to the Power9 idle code to restore SPRG3, which is
user visible and used for sched_getcpu().
Thanks to: Alexey Kardashevskiy, David Gibson. Gautham R. Shenoy,
James Clarke"
* tag 'powerpc-4.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Fix save/restore of SPRG3 on entry/exit from stop (idle)
powerpc/Makefile: Assemble with -me500 when building for E500
KVM: PPC: Check if IOMMU page is contained in the pinned physical page
vfio/spapr: Use IOMMU pageshift rather than pagesize
powerpc/xmon: Fix disassembly since printf changes
|
|
The situation described in the comment can occur also with
PHY_IGNORE_INTERRUPT, therefore change the condition to include it.
Fixes: f555f34fdc58 ("net: phy: fix auto-negotiation stall due to unavailable interrupt")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW hsi contains 256 approximation buckets which are split in ramrod into
eight u32 values, but driver is using eight 'unsigned long' variables.
This patch fixes the mcast logic by making the API utilize u32.
Fixes: 83aeb933 ("qed*: Trivial modifications")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's a possible race where driver can read link status in mid-transition
and see that virtual-link is up yet speed is 0. Since in this
mid-transition we're guaranteed to see a mailbox from MFW soon, we can
afford to treat this as link down.
Fixes: cc875c2e ("qed: Add link support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Apparently, MFW publishes EEE capabilities even for Fiber-boards that don't
support them, and later since qed internally sets adv_caps it would cause
link-flap avoidance (LFA) to fail when driver would initiate the link.
This in turn delays the link, causing traffic to fail.
Driver has been modified to not to ask MFW for any EEE config if EEE isn't
to be enabled.
Fixes: 645874e5 ("qed: Add support for Energy efficient ethernet.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For some time now, if you load the bonding driver and configure bond
parameters via sysfs using minimal config options, such as specifying
nothing but the mode, relying on defaults for everything else, modes
that cannot use arp monitoring (802.3ad, balance-tlb, balance-alb) all
wind up with both arp_interval=0 (as it should be) and miimon=0, which
means the miimon monitor thread never actually runs. This is particularly
problematic for 802.3ad.
For example, from an LNST recipe I've set up:
$ modprobe bonding max_bonds=0"
$ echo "+t_bond0" > /sys/class/net/bonding_masters"
$ ip link set t_bond0 down"
$ echo "802.3ad" > /sys/class/net/t_bond0/bonding/mode"
$ ip link set ens1f1 down"
$ echo "+ens1f1" > /sys/class/net/t_bond0/bonding/slaves"
$ ip link set ens1f0 down"
$ echo "+ens1f0" > /sys/class/net/t_bond0/bonding/slaves"
$ ethtool -i t_bond0"
$ ip link set ens1f1 up"
$ ip link set ens1f0 up"
$ ip link set t_bond0 up"
$ ip addr add 192.168.9.1/24 dev t_bond0"
$ ip addr add 2002::1/64 dev t_bond0"
This bond comes up okay, but things look slightly suspect in
/proc/net/bonding/t_bond0 output:
$ grep -i mii /proc/net/bonding/t_bond0
MII Status: up
MII Polling Interval (ms): 0
MII Status: up
MII Status: up
Now, pull a cable on one of the ports in the bond, then reconnect it, and
you'll see:
Slave Interface: ens1f0
MII Status: down
Speed: 1000 Mbps
Duplex: full
I believe this became a major issue as of commit 4d2c0cda0744, which for
802.3ad bonds, sets slave->link = BOND_LINK_DOWN, with a comment about
relying on link monitoring via miimon to set it correctly, but since the
miimon work queue never runs, the link just stays marked down.
If we simply tweak bond_option_mode_set() slightly, we can check for the
non-arp modes having no miimon value set, and insert BOND_DEFAULT_MIIMON,
which gets things back in full working order. This problem exists as far
back as 4.14, and might be worth fixing in all stable trees since, though
the work-around is to simply specify an miimon value yourself.
Reported-by: Bob Ball <ball@umich.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-07-18
The following series provides fixes to mlx5 core and net device driver.
Please pull and let me know if there's any problem.
For -stable v4.7
net/mlx5e: Don't allow aRFS for encapsulated packets
net/mlx5e: Fix quota counting in aRFS expire flow
For -stable v4.15
net/mlx5e: Only allow offloading decap egress (egdev) flows
net/mlx5e: Refine ets validation function
net/mlx5: Adjust clock overflow work period
For -stable v4.17
net/mlx5: E-Switch, UBSAN fix undefined behavior in mlx5_eswitch_mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on USB2.0 Spec Section 11.12.5,
"If a hub has per-port power switching and per-port current limiting,
an over-current on one port may still cause the power on another port
to fall below specific minimums. In this case, the affected port is
placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the
port, but PORT_OVER_CURRENT is not set."
so let's check C_PORT_OVER_CURRENT too for over current condition.
Fixes: 08d1dec6f405 ("usb:hub set hub->change_bits when over-current happens")
Cc: <stable@vger.kernel.org>
Tested-by: Alessandro Antenucci <antenucci@korg.it>
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull VFIO fix from Alex Williamson:
"Harden potential Spectre v1 issue (Gustavo A. R. Silva)"
* tag 'vfio-v4.18-rc6' of git://github.com/awilliam/linux-vfio:
vfio/pci: Fix potential Spectre v1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix DM writecache target to allow an optional offset to the start of
the data and metadata area.
This allows userspace tools (e.g. LVM2) to place a header and metadata
at the front of the writecache device for its use"
* tag 'for-4.18/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm writecache: support optional offset for start of device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of 8 obvious fixes.
Three (2 qla2xxx and the cxlflash oopses) are regressions, two from
4.17 and one from the merge window. The hpsa change is user visible,
but it fixes an error users have complained about"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxlflash: fix assignment of the backend operations
scsi: qedi: Send driver state to MFW
scsi: qedf: Send the driver state to MFW
scsi: hpsa: correct enclosure sas address
scsi: sd_zbc: Fix variable type and bogus comment
scsi: qla2xxx: Fix NULL pointer dereference for fcport search
scsi: qla2xxx: Fix kernel crash due to late workqueue allocation
scsi: qla2xxx: Fix inconsistent DMA mem alloc/free
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"Only one revert, for an an Intel VT-d patch that caused issues with
the i915 GPU driver"
* tag 'iommu-fixes-v4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
Revert "iommu/vt-d: Clean up pasid quirk for pre-production devices"
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
"The Dell laptop ACPI video brightness control is now back after fixing
a regression brought by SMM refactoring"
* tag 'platform-drivers-x86-v4.18-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: dell-laptop: Fix backlight detection
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a relatively old initialization issue in intel_pstate causing the
pcc-cpufreq driver to be used instead of it on some HP Proliant
systems.
This turned into a functional regression during the 4.17 cycle,
because pcc-cpufreq is a scalability disaster and that was amplified
by the idle loop rework done at that time (Rafael Wysocki).
* tag 'pm-4.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Register when ACPI PCCH is present
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Extend the recently added suspend-to-idle quirk for Thinkpad X1 Carbon
6th to other systems from that familiy which turned out to need it too
(Robin Johnson)"
* tag 'acpi-4.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / EC: Use ec_no_wakeup on more Thinkpad X1 Carbon 6th systems
|
|
If td_list is not empty the cfg_cmd will not be freed,
call xhci_free_command to free it.
Signed-off-by: Zheng Xiaowei <zhengxiaowei@ruijie.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The old code in nvme_user_cmd() passed the userspace virtual address
from nvme_passthru_cmd.metadata as the length of the metadata buffer
as well as the address to nvme_submit_user_cmd().
Fixes: 63263d60 ("nvme: Use metadata for passthrough commands")
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
There is a bug in the sink PDO search code when trying to select
a PPS APDO. The current code actually sets the starting index for
searching to whatever value 'i' is, rather than choosing index 1
to avoid the first PDO (always 5V fixed). As a result, for sources
which support PPS but whose PPS APDO index does not match with the
supporting sink PPS APDO index for the platform, no valid PPS APDO
will be found so this feature will not be permitted.
Sadly in testing, both Source and Sink capabilities matched up and
this was missed. Code is now updated to correctly set the start
index to 1, and testing with additional PPS capable sources show
this to work as expected.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Fixes: 2eadc33f40d4 ("typec: tcpm: Add core support for sink side PPS")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 1b9ba000 ("Allow function drivers to pause control
transfers") states that USB_GADGET_DELAYED_STATUS is only
supported if data phase is 0 bytes.
It seems that when the length is not 0 bytes, there is no
need to explicitly delay the data stage since the transfer
is not completed until the user responds. However, when the
length is 0, there is no data stage and the transfer is
finished once setup() returns, hence there is a need to
explicitly delay completion.
This manifests as the following bugs:
Prior to 946ef68ad4e4 ('Let setup() return
USB_GADGET_DELAYED_STATUS'), when setup is 0 bytes, ffs
would require user to queue a 0 byte request in order to
clear setup state. However, that 0 byte request was actually
not needed and would hang and cause errors in other setup
requests.
After the above commit, 0 byte setups work since the gadget
now accepts empty queues to ep0 to clear the delay, but all
other setups hang.
Fixes: 946ef68ad4e4 ("Let setup() return USB_GADGET_DELAYED_STATUS")
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix return code check for "max brightness" ACPI call.
The Dell laptop ACPI video brightness control is not present on dell
laptops anymore, but was present in older kernel versions.
The code that checks the return value is incorrect since the SMM
refactoring.
The old code was:
if (buffer->output[0] == 0)
Which was changed to:
ret = dell_send_request(...)
if (ret)
However, dell_send_request() will return 0 if buffer->output[0] == 0,
so we must change the check to:
if (ret == 0)
This issue was found on a Dell M4800 laptop, and the fix tested on it
as well.
Fixes: 549b4930f057 ("dell-smbios: Introduce dispatcher for SMM calls")
Signed-off-by: Damien Thébault <damien@dtbo.net>
Tested-by: Damien Thébault <damien@dtbo.net>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
This reverts commit ab96746aaa344fb720a198245a837e266fad3b62.
The commit ab96746aaa34 ("iommu/vt-d: Clean up pasid quirk for
pre-production devices") triggers ECS mode on some platforms
which have broken ECS support. As the result, graphic device
will be inoperable on boot.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107017
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The calculation of "wqe_size" is not correct when the tx queue is busy in
hinic_xmit_frame().
When there are no free WQEs, the tx flow will unmap the skb buffer, then
ring the doobell for the pending packets. But the "wqe_size" which used
to calculate the doorbell address is not correct. The wqe size should be
cleared to 0, otherwise, it will cause a doorbell error.
This patch fixes the problem.
Reported-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"Just two sets of driver fixes this week to follow up on the set from
earlier in the week and hopefully get me realigned schedule wise.
amdgpu:
- ACP fix for boards with multiple I2S instances
- DP fix for CZ, vega
- hybrid laptop fixes
- Resume regression fix
nouveau:
- large memory systems and Pascal fix
- MST race fixes
- runtime PM fix"
* tag 'drm-fixes-2018-07-20' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/fb/gp100-: disable address remapper
drm/amd/amdgpu: creating two I2S instances for stoney/cz (v2)
drm/amdgpu: add another ATPX quirk for TOPAZ
drm/amd/display: Fix DP HBR2 Eye Diagram Pattern on Carrizo
drm/amdgpu: Make sure IB tests flushed after IP resume
drm/nouveau: Set DRIVER_ATOMIC cap earlier to fix debugfs
drm/nouveau: Remove bogus crtc check in pmops_runtime_idle
drm/nouveau/drm/nouveau: Fix runtime PM leak in nv50_disp_atomic_commit()
drm/nouveau: Avoid looping through fake MST connectors
drm/nouveau: Use drm_connector_list_iter_* for iterating connectors
drm/nouveau/gem: off by one bugs in nouveau_gem_pushbuf_reloc_apply()
drm/nouveau/kms/nv50-: ensure window updates are submitted when flushing mst disables
|
|
- fix problem with pascal and large memory systems
- fix a bunch of MST problems
- fix a runtime PM interaction with MST
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CACAvsv79O8deSts2fxJ_oS6=q8yA+OgwBSEpp5R=BQBmWa+oyg@mail.gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.18, round 3:
- Restrict GPC driver on register range that is accessible by regmap,
so that we can avoid user space from triggering imprecise external
abort exception.
* tag 'imx-fixes-4.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: gpc: restrict register range for regmap access
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix crashes that happen when PHY drivers are left disabled in the V3
Semiconductor, MediaTek, Faraday, Aardvark, DesignWare, Versatile,
and X-Gene host controller drivers (Sergei Shtylyov)
- Fix a NULL pointer dereference in the endpoint library configfs
support (Kishon Vijay Abraham I)
- Fix a race condition in Hyper-V IRQ handling (Dexuan Cui)
* tag 'pci-v4.18-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: v3-semi: Fix I/O space page leak
PCI: mediatek: Fix I/O space page leak
PCI: faraday: Fix I/O space page leak
PCI: aardvark: Fix I/O space page leak
PCI: designware: Fix I/O space page leak
PCI: versatile: Fix I/O space page leak
PCI: xgene: Fix I/O space page leak
PCI: OF: Fix I/O space page leak
PCI: endpoint: Fix NULL pointer dereference error when CONFIGFS is disabled
PCI: hv: Disable/enable IRQs rather than BH in hv_compose_msi_msg()
|
|
The ec_no_wakeup matcher added for Thinkpad X1 Carbon 6th gen systems
beyond matched only a single DMI model (20KGS3JF01), that didn't cover
my laptop (20KH002JUS). Change to match based on DMI product family to
cover all X1 6th gen systems.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This was causing problems on a system with a large amount of RAM, where
display push buffers were being fetched incorrectly when placed in high
system memory addresses.
While this commit will resolve the issue on that particular system, the
issue will be avoided completely with another patch to more fully solve
problems with display and large amounts of system memory on Pascal.
It's still probably a good idea to disable this to prevent weird issues
in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Pull networking fixes from David Miller:
"Lots of fixes, here goes:
1) NULL deref in qtnfmac, from Gustavo A. R. Silva.
2) Kernel oops when fw download fails in rtlwifi, from Ping-Ke Shih.
3) Lost completion messages in AF_XDP, from Magnus Karlsson.
4) Correct bogus self-assignment in rhashtable, from Rishabh
Bhatnagar.
5) Fix regression in ipv6 route append handling, from David Ahern.
6) Fix masking in __set_phy_supported(), from Heiner Kallweit.
7) Missing module owner set in x_tables icmp, from Florian Westphal.
8) liquidio's timeouts are HZ dependent, fix from Nicholas Mc Guire.
9) Link setting fixes for sh_eth and ravb, from Vladimir Zapolskiy.
10) Fix NULL deref when using chains in act_csum, from Davide Caratti.
11) XDP_REDIRECT needs to check if the interface is up and whether the
MTU is sufficient. From Toshiaki Makita.
12) Net diag can do a double free when killing TCP_NEW_SYN_RECV
connections, from Lorenzo Colitti.
13) nf_defrag in ipv6 can unnecessarily hold onto dst entries for a
full minute, delaying device unregister. From Eric Dumazet.
14) Update MAC entries in the correct order in ixgbe, from Alexander
Duyck.
15) Don't leave partial mangles bpf program in jit_subprogs, from
Daniel Borkmann.
16) Fix pfmemalloc SKB state propagation, from Stefano Brivio.
17) Fix ACK handling in DCTCP congestion control, from Yuchung Cheng.
18) Use after free in tun XDP_TX, from Toshiaki Makita.
19) Stale ipv6 header pointer in ipv6 gre code, from Prashant Bhole.
20) Don't reuse remainder of RX page when XDP is set in mlx4, from
Saeed Mahameed.
21) Fix window probe handling of TCP rapair sockets, from Stefan
Baranoff.
22) Missing socket locking in smc_ioctl(), from Ursula Braun.
23) IPV6_ILA needs DST_CACHE, from Arnd Bergmann.
24) Spectre v1 fix in cxgb3, from Gustavo A. R. Silva.
25) Two spots in ipv6 do a rol32() on a hash value but ignore the
result. Fixes from Colin Ian King"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (176 commits)
tcp: identify cryptic messages as TCP seq # bugs
ptp: fix missing break in switch
hv_netvsc: Fix napi reschedule while receive completion is busy
MAINTAINERS: Drop inactive Vitaly Bordug's email
net: cavium: Add fine-granular dependencies on PCI
net: qca_spi: Fix log level if probe fails
net: qca_spi: Make sure the QCA7000 reset is triggered
net: qca_spi: Avoid packet drop during initial sync
ipv6: fix useless rol32 call on hash
ipv6: sr: fix useless rol32 call on hash
net: sched: Using NULL instead of plain integer
net: usb: asix: replace mii_nway_restart in resume path
net: cxgb3_main: fix potential Spectre v1
lib/rhashtable: consider param->min_size when setting initial table size
net/smc: reset recv timeout after clc handshake
net/smc: add error handling for get_user()
net/smc: optimize consumer cursor updates
net/nfc: Avoid stalls when nfc_alloc_send_skb() returned NULL.
ipv6: ila: select CONFIG_DST_CACHE
net: usb: rtl8150: demote allmulti message to dev_dbg()
...
|
|
GPC registers are NOT continuous, some registers are
reserved and accessing them from userspace will trigger
external abort, add regmap register access table to
avoid below abort:
root@imx6slevk:~# cat /sys/kernel/debug/regmap/20dc000.gpc/registers
[ 108.480477] Unhandled fault: imprecise external abort (0x1406) at 0xb6db5004
[ 108.487985] pgd = 42b54bfd
[ 108.490741] [b6db5004] *pgd=ba1b7831
[ 108.494386] Internal error: : 1406 [#1] SMP ARM
[ 108.498943] Modules linked in:
[ 108.502043] CPU: 0 PID: 389 Comm: cat Not tainted 4.18.0-rc1-00074-gc9f1f60-dirty #482
[ 108.509982] Hardware name: Freescale i.MX6 SoloLite (Device Tree)
[ 108.516123] PC is at regmap_mmio_read32le+0x20/0x24
[ 108.521031] LR is at regmap_mmio_read+0x40/0x60
[ 108.525586] pc : [<c059cf74>] lr : [<c059d1ac>] psr: 20060093
[ 108.531875] sp : eccf1d98 ip : eccf1da8 fp : eccf1da4
[ 108.537122] r10: ec2d3800 r9 : eccf1f60 r8 : ecfc0000
[ 108.542370] r7 : eccf1e2c r6 : eccf1e2c r5 : 00000028 r4 : ec338e00
[ 108.548920] r3 : 00000000 r2 : eccf1e2c r1 : f0980028 r0 : 00000000
[ 108.555474] Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none
[ 108.562720] Control: 10c5387d Table: acf4004a DAC: 00000051
[ 108.568491] Process cat (pid: 389, stack limit = 0xd4318a65)
[ 108.574174] Stack: (0xeccf1d98 to 0xeccf2000)
Fixes: 721cabf6c660 ("soc: imx: move PGC handling to a new GPC driver")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|