| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit 923b93e451db876d1479d3e4458fce14fec31d1c.
Make sure consumers do not overwrite gpio flags for pins that have
already been claimed.
While adding support for gpio drivers to refuse a request using
unsupported flags, the order of when the requested flag was checked and
the new flags were applied was reversed to that consumers could
overwrite flags for already requested gpios.
This not only affects device-tree setups where two drivers could request
the same gpio using conflicting configurations, but also allowed user
space to clear gpio flags for already claimed pins simply by attempting
to export them through the sysfs interface. By for example clearing the
FLAG_ACTIVE_LOW flag this way, user space could effectively change the
polarity of a signal.
Reverting this change obviously prevents gpio drivers from doing sanity
checks on the flags in their request callbacks. Fortunately only one
recently added driver (gpio-tps65218 in v4.6) appears to do this, and a
follow up patch could restore this functionality through a different
interface.
Cc: stable <stable@vger.kernel.org> # 4.4
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This fixes the issue descirbe in bug 117531
(https://bugzilla.kernel.org/show_bug.cgi?id=117531).
It's a regression introduced in linux 4.5 that causes a Oops at load of
gpio_sch and prevents powering off the computer.
The issue is that sch_gpio_reg_set is called in sch_gpio_probe before
gpio_chip data is initialized with the pointer to the sch_gpio struct. As
sch_gpio_reg_set calls gpiochip_get_data, it returns NULL which causes
the Oops.
The patch follows Mika's advice (https://lkml.org/lkml/2016/5/9/61) and
consists in modifying sch_gpio_reg_get and sch_gpio_reg_set to take a
sch_gpio struct directly instead of a gpio_chip, which avoids the call to
gpiochip_get_data.
Thanks Mika for your patience with me :-)
Cc: stable@vger.kernel.org
Signed-off-by: Colin Pitrat <colin.pitrat@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Snooze is a poll idle state in powernv and pseries platforms. Snooze
has a timeout so that if a CPU stays in snooze for more than target
residency of the next available idle state, then it would exit
thereby giving chance to the cpuidle governor to re-evaluate and
promote the CPU to a deeper idle state. Therefore whenever snooze
exits due to this timeout, its last_residency will be target_residency
of the next deeper state.
Commit e93e59ce5b85 "cpuidle: Replace ktime_get() with local_clock()"
changed the math around last_residency calculation. Specifically,
while converting last_residency value from nano- to microseconds, it
carries out right shift by 10. Because of that, in snooze timeout
exit scenarios last_residency calculated is roughly 2.3% less than
target_residency of the next available state. This pattern is picked
up by get_typical_interval() in the menu governor and therefore
expected_interval in menu_select() is frequently less than the
target_residency of any state other than snooze.
Due to this we are entering snooze at a higher rate, thereby
affecting the single thread performance.
Fix this by using more precise division via ktime_us_delta().
Fixes: e93e59ce5b85 "cpuidle: Replace ktime_get() with local_clock()"
Reported-by: Anton Blanchard <anton@samba.org>
Bisected-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Per VT-d spec Section 10.4.2 ("Capability Register"), the maximum
number of possible domains is 64K; indeed this is the maximum value
that the cap_ndoms() macro will expand to. Since the value 65536
will not fix in a u16, the 'did' variable must be promoted to an
int, otherwise the test for < 65536 will always be true and the
loop will never end.
The symptom, in my case, was a hung machine during suspend.
Fixes: 3bd4f9112f87 ("iommu/vt-d: Fix overflow of iommu->domains array")
Signed-off-by: Aaron Campbell <aaron@monkey.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When initializing the PHY control register, the FIFO depth bits are
written without reading the previous register value, i.e. all other
bits are overwritten with zero. This disables automatic MDI-X
configuration, which is enabled by default. Fix initialization by doing
a read/modify/write operation.
Signed-off-by: Stefan Hauser <stefan@shauser.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interrupt worker code for the enc28j60 relies only on the TXIF flag to
determinate if the packet transmission was completed. However the datasheet
specifies in section 12.1.3 that TXERIF will clear the TXRTS after a
transmit abort. Also in section 12.1.4 that TXIF will be set
when TXRTS transitions from '1' to '0'. Therefore the TXIF flag is enabled
during transmission errors.
This causes a race condition, since the worker code will invoke
enc28j60_tx_clear() -> netif_wake_queue(), potentially invoking the
ndo_start_xmit function to send a new packet. The enc28j60_send_packet function
uses a workqueue that invokes enc28j60_hw_tx(). In between this function is
called, the worker from the interrupt handler will enter the path for error
handler because of the TXERIF flag, causing to invoke enc28j60_tx_clear() again
and releasing the packet scheduled for transmission, causing a kernel crash with
due a NULL pointer.
These crashes due a NULL pointer were observed under stress conditions of the
device. A BUG_ON() sequence was used to validate the issue was fixed, and has
been running without problems for 2 years now.
Signed-off-by: Diego Dompe <dompe@hpe.com>
Acked-by: Sergio Valverde <sergio.valverde@hpe.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(resent due to overhelpful mail client corrupting patch)
At least on Meson GXBB, the CORE_IRQ_MTL_RX_OVERFLOW interrupt is thrown
with the stmmac1000 driver, which does not support set_rx_tail_ptr. With
this patch and the clock fixes, 1G ethernet works on ODROID-C2.
Signed-off-by: Matt Corallo <git@bluematt.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes frlm Dave Airlie:
"Just some AMD and Intel fixes, the AMD ones are further production
Polaris fixes, and the Intel ones fix some early timeouts, some PCI ID
changes and a couple of other fixes.
Still a bit Internet challenged here, hopefully end of next week will
solve it"
* tag 'drm-fixes-for-v4.7-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Fix missing unlock on error in i915_ppgtt_info()
drm/amd/powerplay: workaround for UVD clock issue
drm/amdgpu: add ACLK_CNTL setting for polaris10
drm/amd/powerplay: fix issue uvd dpm can't enabled on Polaris11.
drm/amd/powerplay: Workaround for Memory EDC Error on Polaris10.
drm/i915: Removing PCI IDs that are no longer listed as Kabylake.
drm/i915: Add more Kabylake PCI IDs.
drm/i915: Avoid early timeout during AUX transfers
drm/i915/hsw: Avoid early timeout during LCPLL disable/restore
drm/i915/lpt: Avoid early timeout during FDI PHY reset
drm/i915/bxt: Avoid early timeout during PLL enable
drm/i915: Refresh cached DP port register value on resume
drm/amd/powerplay: Update CKS on/ CKS off voltage offset calculation
drm/amd/powerplay: disable FFC.
drm/amd/powerplay: add some definition for FFC feature on polaris.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few small driver-specific fixes for SPI, all in the normal important
if you hit them category especially the rockchip driver fix which
addresses a race which has been exposed more frequently with some
recent performance improvements"
* tag 'spi-fix-v4.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: sunxi: fix transfer timeout
spi: sun4i: fix FIFO limit
spi: rockchip: Signal unfinished DMA transfers
spi: spi-ti-qspi: Suspend the queue before removing the device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Two small fixes for the regulator subsystem - one fixing a crash with
one of the devices supported by the max77620 driver, another fixing
startup for the anatop regulator when it starts up with the regulator
in bypass mode"
* tag 'regulator-fix-v4.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: max77620: check for valid regulator info
regulator: anatop: allow regulator to be in bypass mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A small fix for the newly added oxnas clk driver and a handful of
rockchip clk driver fixes for newly added rk3399 support"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: Fix return value check in oxnas_stdclk_probe()
clk: rockchip: release io resource when failing to init clk on rk3399
clk: rockchip: fix cpuclk registration error handling
clk: rockchip: Revert "clk: rockchip: reset init state before mmc card initialization"
clk: rockchip: fix incorrect parent for rk3399's {c,g}pll_aclk_perihp_src
clk: rockchip: mark rk3399 GIC clocks as critical
clk: rockchip: initialize flags of clk_init_data in mmc-phase clock
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
here's a batch of i915 fixes for 4.7.
* tag 'drm-intel-fixes-2016-06-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix missing unlock on error in i915_ppgtt_info()
drm/i915: Removing PCI IDs that are no longer listed as Kabylake.
drm/i915: Add more Kabylake PCI IDs.
drm/i915: Avoid early timeout during AUX transfers
drm/i915/hsw: Avoid early timeout during LCPLL disable/restore
drm/i915/lpt: Avoid early timeout during FDI PHY reset
drm/i915/bxt: Avoid early timeout during PLL enable
drm/i915: Refresh cached DP port register value on resume
|
|
into drm-fixes
Just a few more late fixes for Polaris cards.
* 'drm-fixes-4.7' of git://people.freedesktop.org/~agd5f/linux:
drm/amd/powerplay: workaround for UVD clock issue
drm/amdgpu: add ACLK_CNTL setting for polaris10
drm/amd/powerplay: fix issue uvd dpm can't enabled on Polaris11.
drm/amd/powerplay: Workaround for Memory EDC Error on Polaris10.
drm/amd/powerplay: Update CKS on/ CKS off voltage offset calculation
drm/amd/powerplay: disable FFC.
drm/amd/powerplay: add some definition for FFC feature on polaris.
|
|
Since commit 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
the penalty values are calculated on the fly rather than at boot time.
This works fine for PCI interrupts but not so well for ISA interrupts.
The information on whether or not an ISA interrupt is in use is not
available to the pci_link.c code directly. That information is
obtained from the outside via acpi_penalize_isa_irq(). [If its
"active" argument is true, then the IRQ is in use by ISA.]
Since the current code relies on PCI Link objects for determination
of penalties, we are factoring in the PCI penalty twice after
acpi_penalize_isa_irq() function is called.
To avoid that, limit the newly added functionality to just PCI
interrupts so that old behavior is still maintained.
Fixes: 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Trying to make the ISA and PCI init functionality common turned out
to be a bad idea, because the ISA path depends on external
functionality.
Restore the previous behavior and limit the refactoring to PCI
interrupts only.
Fixes: 1fcb6a813c4f "ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()"
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The change introduced in commit 103544d86976 (ACPI,PCI,IRQ: reduce
resource requirements) omitted the initially applied PCI_POSSIBLE
penalty when the IRQ is active.
Incorrect calculation of the penalty leads the ACPI code to assigning
a wrong interrupt number to a PCI INTx interrupt.
This would not be as bad as it sounds in theory. It would just cause
the interrupts to be shared and result in performance penalty.
However, some drivers (like the parallel port driver) don't like
interrupt sharing and in the above case they will causes all of
the PCI drivers wanting to share the interrupt to be unable to
request it.
The issue has not been caught in testing because the behavior is
platform-specific and depends on the peripherals ending up sharing
the IRQ and their drivers.
Before the above commit the code would add the PCI_POSSIBLE value
divided by the number of possible IRQ users to the IRQ penalty
during initialization.
Later in that code path, if the IRQ is chosen as the active IRQ or
if it is used by ISA; additional penalties are added.
Fixes: 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix an expression in the ACPI PCI IRQ management code added by a
recent commit that overlooked missing parens in it, so the result of
the computation is incorrect in some cases (Sinan Kaya)"
* tag 'acpi-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI,PCI,IRQ: correct operator precedence
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Three cpufreq fixes, one in the core (stable-candidate) and two in
drivers (intel_pstate and cpufreq-dt).
Specifics:
- Fix a recent intel_pstate regression that caused the number of
wakeups to increase significantly on an idle system in some cases
due to excessive synchronize_sched() invocations (Rafael Wysocki).
- Fix unnecessary invocations of WARN_ON() in the cpufreq core after
cpufreq has been suspended introduced during the 4.6 cycla (Rafael
Wysocki).
- Fix an error code path in the cpufreq-dt-platdev driver that
forgets to drop a reference to a DT node (Masahiro Yamada)"
* tag 'pm-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Avoid false-positive WARN_ON()s in cpufreq_update_policy()
cpufreq: dt: call of_node_put() before error out
intel_pstate: Do not clear utilization update hooks on policy changes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull more MFD fixes from Lee Jones:
"Apologies for missing these from the first pull request.
Final patches fixing Reset API change"
* tag 'mfd-fixes-4.7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
usb: dwc3: st: Use explicit reset_control_get_exclusive() API
phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
phy: miphy28lp: Inform the reset framework that our reset line may be shared
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"1/ Two regression fixes since v4.6: one for the byte order of a sysfs
attribute (bz121161) and another for QEMU 2.6's NVDIMM _DSM (ACPI
Device Specific Method) implementation that gets tripped up by new
auto-probing behavior in the NFIT driver.
2/ A fix tagged for -stable that stops the kernel from
clobbering/ignoring changes to the configuration of a 'pfn'
instance ("struct page" driver). For example changing the
alignment from 2M to 1G may silently revert to 2M if that value is
currently stored on media.
3/ A fix from Eric for an xfstests failure in dax. It is not
currently tagged for -stable since it requires an 8-exabyte file
system to trigger, and there appear to be no user visible side
effects"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: fix format interface code byte order
dax: fix offset overflow in dax_io
acpi, nfit: fix acpi_check_dsm() vs zero functions implemented
libnvdimm, pfn, dax: fix initialization vs autodetect for mode + alignment
|
|
On 64bits kernels, device stats are 64bits wide, not 32bits.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid recursions of dev_queue_xmit() to the wrong net device when
frames are unprotected, since at that time skb->dev still points to
our own macsec dev and unlike macsec_encrypt_finish() dev pointer
doesn't get updated to real underlying device.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO fixes from Greg KH:
"Here are a few small staging and iio driver fixes for 4.7-rc6.
Nothing major here, just a number of small fixes, all have been in
linux-next for a while, and the full details are in the shortlog"
* tag 'staging-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio:ad7266: Fix probe deferral for vref
iio:ad7266: Fix support for optional regulators
iio:ad7266: Fix broken regulator error handling
iio: accel: kxsd9: fix the usage of spi_w8r8()
staging: iio: accel: fix error check
staging: iio: ad5933: fix order of cycle conditions
staging: iio: fix ad7606_spi regression
iio: inv_mpu6050: Fix use-after-free in ACPI code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fixes from Greg KH:
"Here are two tty fixes for some reported issues. One resolves a crash
in devpts, and the other resolves a problem with the fbcon cursor
blink causing lockups.
Both have been in linux-next with no reported problems"
* tag 'tty-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
devpts: fix null pointer dereference on failed memory allocation
tty: vt: Fix soft lockup in fbcon cursor blink timer.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY fixes from Greg KH:
"Here are a number of small USB and PHY driver fixes for 4.7-rc6.
Nothing major here, all are described in the shortlog below. All have
been in linux-next with no reported issues"
* tag 'usb-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: don't free bandwidth_mutex too early
USB: EHCI: declare hostpc register as zero-length array
phy-sun4i-usb: Fix irq free conditions to match request conditions
phy: bcm-ns-usb2: checking the wrong variable
phy-sun4i-usb: fix missing __iomem *
phy: phy-sun4i-usb: Fix optional gpios failing probe
phy: rockchip-dp: fix return value check in rockchip_dp_phy_probe()
phy: rcar-gen3-usb2: fix unexpected repeat interrupts of VBUS change
usb: common: otg-fsm: add license to usb-otg-fsm
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Three fixes:
- Fix use of smp_processor_id() in preemptible code in the IOVA
allocation code. This got introduced with the scalability
improvements in this release cycle.
- A VT-d fix for out-of-bounds access of the iommu->domains array.
The bug showed during suspend/resume.
- AMD IOMMU fix to print the correct device id in the ACPI parsing
code"
* tag 'iommu-fixes-v4.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Initialize devid variable before using it
iommu/vt-d: Fix overflow of iommu->domains array
iommu/iova: Disable preemption around use of this_cpu_ptr()
|
|
'regulator/fix/max77620' into regulator-linus
|
|
Add Link UP/Down prints to kernel log when link state changes
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Valid weight assigned to ETS TClass values are 1-100
Fixes: 08fb1dacdd76 ('net/mlx5e: Support DCBNL IEEE ETS')
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default fallback function used by mlx5e select queue can return
any TX queues in range [0..dev->num_real_tx_queues).
The current implementation assumes that the fallback function returns
a number in the range [0.. number of channels). Actually
dev->num_real_tx_queues = (number of channels) * dev->num_tc;
which is more than the expected range if num_tc is configured and could
lead to crashes.
To fix this we test if num_tc is not configured we can safely return the
fallback suggestion, if not we will reciprocal_scale the fallback
result and normalize it to the desired range.
Fixes: 08fb1dacdd76 ('net/mlx5e: Support DCBNL IEEE ETS')
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ConnectX4-Lx uses an inline wqe mode that currently defaults to
requiring the entire L2 header be included in the wqe.
This patch fixes mlx5e_get_inline_hdr_size() to account for
all L2 headers (VLAN, QinQ, etc) using skb_network_offset(skb).
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a timeout to avoid an infinite loop waiting for RQ's to flush. This
occurs during AER/EEH and will also happen if the device stops posting
completions due to internal error or reset, or if moving the RQ to the
error state fails. Also cleanup posted receive resources when closing
the RQ.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add callback to handle TX timeouts.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid an infinite loop by timing out waiting for the SQ to flush. Also
clean up the TX descriptors if that happens.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation does not handle timeout in case of command
with callback request, and this can lead to deadlock if the command
doesn't get fw response.
Add delayed callback timeout work before posting the command to fw.
In case of real fw command completion we will cancel the delayed work.
In case of fw command timeout the callback timeout handler will be
called and it will simulate fw completion with timeout error.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call command completion handler in case of timeout when working in
interrupts mode.
Avoid flushing the commands workqueue after acquiring the semaphores to
prevent a potential deadlock.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device ID for VFs is in a different location than PFs. This results
in the poll always timing out for VFs. There's no good way to read the
VF device ID without using the PF's configuration space. Switch to waiting
for the health poll to start incrementing. Also remove the 1s sleep
at the beginning.
fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core
driver')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change page cleanup flow when in internal error to properly decrement
the page counts when reclaiming pages. The prevents timing out waiting
for extra pages that were actually cleaned up previously.
fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In internal error state the health poll thread will eventually call
synchronize_irq() (to safely trigger command completions) which might
sleep, so we are calling sleeping function from atomic context which is
invalid.
Here we move trigger_cmd_completions(dev) to enter error state which is
the earliest stage in error state handling.
This way we won't need to wait for next health poll to trigger command
completions and will solve the scheduling while atomic issue.
mlx5_enter_error_state can be called from two contexts, protect it with
dev->intf_state_lock
Fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of internal error state we will simulate the commands status
through the return value translation function, but we need to simulate
all the teardown fw commands as successful so we will not have fw
command failure prints.
This also fix memory leaks that happen because we skip teardown stages
due to failed fw commands.
Fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ether_addr_equal_64bits() requires some care about its arguments,
namely that 8 bytes might be read, even if last 2 byte values are not
used.
KASan detected a violation with null_mac_addr and lacpdu_mcast_addr
in bond_3ad.c
Same problem with mac_bcast[] and mac_v6_allmcast[] in bond_alb.c :
Although the 8-byte alignment was there, KASan would detect out
of bound accesses.
Fixes: 815117adaf5b ("bonding: use ether_addr_equal_unaligned for bond addr compare")
Fixes: bb54e58929f3 ("bonding: Verify RX LACPDU has proper dest mac-addr")
Fixes: 885a136c52a8 ("bonding: use compare_ether_addr_64bits() in ALB")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If mvneta_mdio_probe() fails, a kernel warning is triggered due to
missing cleanup in the error path. Add the necessary cleanup.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 281 at kernel/irq/manage.c:1814 __free_percpu_irq+0xfc/0x130
percpu IRQ 38 still enabled on CPU0!
Modules linked in: bnep bluetooth xhci_plat_hcd xhci_hcd marvell_cesa armada_thermal des_generic ehci_orion mcp3021 spi_orion sfp mdio_i2c evbug fuse
CPU: 1 PID: 281 Comm: connmand Not tainted 4.7.0-rc2+ #53
Hardware name: Marvell Armada 380/385 (Device Tree)
Backtrace:
[<c0013488>] (dump_backtrace) from [<c00137d0>] (show_stack+0x18/0x1c)
r6:60010093 r5:ffffffff r4:00000000 r3:dc8ba500
[<c00137b8>] (show_stack) from [<c02c6fe0>] (dump_stack+0xa4/0xdc)
[<c02c6f3c>] (dump_stack) from [<c002d4ec>] (__warn+0xd8/0x104)
r6:c081e6a0 r5:00000000 r4:edfe5d50 r3:dc8ba500
[<c002d414>] (__warn) from [<c002d5d0>] (warn_slowpath_fmt+0x40/0x48)
r10:a0010013 r8:c09356f8 r7:00000026 r6:ef11a260 r5:edd7b980 r4:ef11a200
[<c002d594>] (warn_slowpath_fmt) from [<c008c8e0>] (__free_percpu_irq+0xfc/0x130)
r3:00000026 r2:c081e7ac
[<c008c7e4>] (__free_percpu_irq) from [<c008c95c>] (free_percpu_irq+0x48/0x74)
r10:00008914 r8:00000000 r7:ffffffed r6:c09356f8 r5:00000026 r4:ef11a200
[<c008c914>] (free_percpu_irq) from [<c043dd70>] (mvneta_open+0x118/0x134)
r6:ffffffed r5:ef01e640 r4:ef01e000 r3:ef01e000
[<c043dc58>] (mvneta_open) from [<c055f5b4>] (__dev_open+0xa4/0x108)
r7:ef01e030 r6:c06ff3d8 r5:ffff9003 r4:ef01e000
[<c055f510>] (__dev_open) from [<c055f844>] (__dev_change_flags+0x94/0x150)
r7:00001002 r6:00000001 r5:ffff9003 r4:ef01e000
[<c055f7b0>] (__dev_change_flags) from [<c055f938>] (dev_change_flags+0x20/0x50)
r8:00000000 r7:c09334c8 r6:00001002 r5:00000148 r4:ef01e000 r3:00008914
[<c055f918>] (dev_change_flags) from [<c05de044>] (devinet_ioctl+0x6f4/0x7e0)
r8:00000000 r7:c09334c8 r6:00000000 r5:ee87200c r4:00000000 r3:00008914
[<c05dd950>] (devinet_ioctl) from [<c05e0168>] (inet_ioctl+0x1b8/0x1c8)
r10:beb4499c r9:edfe4000 r8:ecf13280 r7:c096cf00 r6:beb4499c r5:eef7c240
r4:00008914
[<c05dffb0>] (inet_ioctl) from [<c053c898>] (sock_ioctl+0x78/0x300)
[<c053c820>] (sock_ioctl) from [<c0155ecc>] (do_vfs_ioctl+0x98/0xa60)
r7:00000011 r6:00008914 r5:00000011 r4:c01568d0
[<c0155e34>] (do_vfs_ioctl) from [<c01568d0>] (SyS_ioctl+0x3c/0x60)
r10:00000000 r9:edfe4000 r8:beb4499c r7:00000011 r6:00008914 r5:ecf13280
r4:ecf13280
[<c0156894>] (SyS_ioctl) from [<c000fe60>] (ret_fast_syscall+0x0/0x1c)
r8:c0010004 r7:00000036 r6:00000011 r5:000a2978 r4:00000000 r3:00009003
---[ end trace 711f625d5b04b3a7 ]---
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LINK_OFF_WAKE_EN should be cleared after autoresume, otherwise after
system suspend, the system would wake up when linking off occurs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We're making all reset line users specify whether their lines are
shared with other IP or they operate them exclusively. In this case
the line is exclusively used only by this IP, so use the *_exclusive()
API accordingly.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We're making all reset line users specify whether their lines are
shared with other IP or they operate them exclusively. In this case
the line is exclusively used only by this IP, so use the *_exclusive()
API accordingly.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
On the STiH410 B2120 development board the MiPHY28lp shares its reset
line with the Synopsys DWC3 SuperSpeed (SS) USB 3.0 Dual-Role-Device
(DRD). New functionality in the reset subsystems forces consumers to
be explicit when requesting shared/exclusive reset lines.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Call wmb() to ensure writes are complete before
hardware fetches updated Tx descriptors.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far, we were missing to send the vblank event when disabling the CRTC,
making us never report the last vblank event.
This was causing a time out on the page flip, which should be solved now.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The sun4i display engine doesn't have any vblank counter. Use the proper
helper for that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
"Contained are some standard fixes and unusually an extension to the
Reset API. Some of those changes are required to fix a bug introduced
in -rc1, which introduces extra 'reset line checks' i.e. whether the
line is shared or not. If a line is shared and the new *_shared() API
is not used, the request fails with an error. This breaks USB in v4.7
for ST's platforms.
Admittedly, there are some patches contained in our (MFD/Reset)
immutable branch which are not true -fixes, but there isn't anything I
can do about that. Rest assured though, there aren't any API
'changes'. Everything is the same from the consumer's perspective.
- Use new reset_*_get_shared() variant to prevent reset line
obtainment failure (Fixes commit 0b52297f2288: "reset: Add support
for shared reset controls")
- Fix unintentional switch() fall-through into error path
- Fix uninitialised variable compiler warning"
* tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: da9053: Fix compiler warning message for uninitialised variable
mfd: max77620: Fix FPS switch statements
phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
usb: dwc3: st: Inform the reset framework that our reset line may be shared
usb: host: ehci-st: Inform the reset framework that our reset line may be shared
usb: host: ohci-st: Inform the reset framework that our reset line may be shared
reset: TRIVIAL: Add line break at same place for similar APIs
reset: Supply *_shared variant calls when using *_optional APIs
reset: Supply *_shared variant calls when using of_* API
reset: Ensure drivers are explicit when requesting reset lines
reset: Reorder inline reset_control_get*() wrappers
|
