Age | Commit message (Collapse) | Author |
|
This patch is to let ethtool enable/disable the tc flower offload
features. Hardware ENETC has the feature of PSFP which is for per-stream
policing. When enable the tc hw offloading feature, driver would enable
the IEEE 802.1Qci feature. It is only set the register enable bit for
this feature not enable for any entry of per stream filtering and stream
gate or stream identify but get how much capabilities for each feature.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The side band interrupt service routine is not available on chips
like 7211, or rather, it does not permit the signaling of wake-up
events due to the complex interrupt hierarchy.
Move the wake-up event accounting into a .resume_noirq function,
account for possible wake-up events and clear the MPD/HFB interrupts
from there, while leaving the hardware untouched until the resume
function proceeds with doing its usual business.
Because bcmgenet_wol_power_down_cfg() now enables the MPD and HFB
interrupts, it is invoked by a .suspend_noirq function to prevent
the servicing of interrupts after the clocks have been disabled.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible for a GSI channel's state to be changed as a result
of an action by a different execution environment. Specifically,
the modem is able to issue a GSI generic command that causes a state
change on a GSI channel associated with the AP.
A channel's state only needs to be known when a channel is allocated
or deallocaed, started or stopped, or reset. So there is little
value in caching the state anyway.
Stop recording a copy of the channel's last known state, and instead
fetch the true state from hardware whenever it's needed. In such
cases, *do* record the state in a local variable, in case an error
message reports it (so the value reported is the value seen).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass a channel pointer rather than a GSI pointer and channel ID to
gsi_channel_state().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for reading and reporting the 10G link status on the
88e6390 in addition to the 1000BASE-X/2500BASE-X/SGMII status.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The private MV88E6390_PCS_CONTROL_1 definitions in serdes.h reflects
the IEEE 802.3 standard PCS control register 1 definitions, only
offset by 0x1000 in the PHYXS register space. Rather than inventing
our own, use those that already exist, and name the register
MV88E6390_10G_CTRL1.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Chip generations are mostly compatible register-wise, but there are still
some differences. Therefore we've made some of first generation (A1) code
non-static to re-use it where possible.
Some pieces are A2 specific, in which case we redefine/extend such APIs.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds basic A2 HW initialization / deinitialization.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Co-developed-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds common functions (mostly FW-related), which are
needed for basic A2 HW initialization / deinitialization.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Co-developed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds A2 register definitions for basic A2 HW
initialization / deinitialization.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Co-developed-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Co-developed-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds RPF-related hw_ops, which are needed for basic
functionality.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Co-developed-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RPF is one of the modules which has been significantly
changed/extended on A2.
This patch adds the necessary A2 register definitions
for RPF, which are used in follow-up patches.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Co-developed-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds basic hw_ops layout for A2.
Actual implementation will be added in the follow-up patches.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the minimum set of FW ops for A2.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Co-developed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the bare minimum of A2 HW bindings required to
get fw_ops working.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the driver<->firmware interface for A2
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IS_CHIP feature will be used to differentiate between A1 and A2,
where necessary. Thus, move it to aq_hw.h, rename it and make
it accept the 'hw' pointer.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes potential crash in case if hw_get_regs is NULL.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hw_get_fw_version() never fails, so this patch simplifies its
usage by utilizing return value instead of output argument.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A2 will have a different implementation of these 2 APIs, so
this patch moves them to hw_ops in preparation for A2.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Co-developed-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds defines for 10M and EEE 100M link modes, which are
supported by A2.
10M support is added in this patch series.
EEE is out of scope, but will be added in a follow-up series.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding device ids for the new generation of atlantic nic.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Aquantia is now part of Marvell. Thus, update the driver description.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
davinci_mdio_probe()
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
since devm_ioremap() does not check input parameters for null.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = \(platform_get_resource\|platform_get_resource_byname\)(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: 03f66f067560 ("net: ethernet: ti: davinci_mdio: use devm_ioremap()")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No new feature, just to simplify stm32 part to be easier to use.
Add by default all Ethernet clocks in DT, and activate or not in function
of phy mode, clock frequency, if property "st,ext-phyclk" is set or not.
Keep backward compatibility
--------------------------------------------------------------------------
|PHY_MODE | Normal | PHY wo crystal| PHY wo crystal | No 125Mhz |
| | | 25MHz | 50MHz | from PHY |
--------------------------------------------------------------------------
| MII | - | eth-ck | n/a | n/a |
| | | st,ext-phyclk | | |
--------------------------------------------------------------------------
| GMII | - | eth-ck | n/a | n/a |
| | | st,ext-phyclk | | |
--------------------------------------------------------------------------
| RGMII | - | eth-ck | n/a | eth-ck |
| | | st,ext-phyclk | |st,eth-clk-sel|
| | | | | or |
| | | | | st,ext-phyclk|
----------------==--------------------------------------------------------
| RMII | - | eth-ck | eth-ck | n/a |
| | | st,ext-phyclk | st,eth-ref-clk-sel | |
| | | | or st,ext-phyclk | |
--------------------------------------------------------------------------
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Considering the few messages we have in the driver, there's not really
a benefit in being able to control them on a message type level.
Therefore simplify the code and switch to the netdev_xxx message
functions. In addition add net_ratelimit() to messages that can be
printed from a hot path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When preparing an unrelated change, checkpatch complained about this
redundant out-of-memory message. Therefore remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The counter handling functions can only fail if rtl8169_do_counters()
times out. In the poll function we emit an error message in case of
timeout, therefore we don't have to propagate the timeout all the
way up just to print another message basically saying the same.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Net core - __dev_set_promiscuity - prints a message already when
promiscuous mode in entered/left, therefore we don't have to do this
in the driver too. Also the driver message would be misleading
(would be because "link" message level is disabled per default)
because it would print "promisc mode enabled" even if it's being
left. Reason is that __dev_change_flags() calls dev_set_rx_mode()
before touching the promisc flag.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark tables as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- add a document title;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- mark lists as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- add a document title;
- comment out text-only TOC from html/pdf output;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;
- use copyright symbol;
- use :field: markup;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;
- use copyright symbol;
- use :field: markup;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- mark code blocks and literals as such;
- mark lists as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- add a document title;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- use copyright symbol;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;
- mark code blocks and literals as such;
- add notes markups;
- mark tables as such;
- mark lists as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- add a document title;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- use copyright symbol;
- adjust titles and chapters, adding proper markups;
- mark tables as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- use copyright symbol;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove a not needed parameter in rtl8169_set_magic_reg.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes coccicheck warnings:
drivers/net/ethernet/huawei/hinic/hinic_hw_mbox.c:452:17-24: WARNING opportunity for kmemdup
drivers/net/ethernet/huawei/hinic/hinic_hw_mbox.c:458:23-30: WARNING opportunity for kmemdup
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix sparse warnings:
drivers/net/ethernet/huawei/hinic/hinic_hw_mbox.c:601:6: warning: symbol 'dump_mox_reg' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This PHY has two PHY IDs depending on its mode. Adjust the mask so that
it includes both IDs.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The lower three bits of the phy_id specifies the chip stepping. The
workaround is specifically for the B0 stepping. Apply it only on these
chips.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Broadcom defines the bits for this PHY as follows:
{ oui[24:3], model[6:0], revision[2:0] }
Thus we have to mask the lower three bits only.
Fixes: 6937602ed3f9 ("net: phy: add Broadcom BCM54140 support")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|