| Age | Commit message (Collapse) | Author |
|---|
|
Only use the read sge lkey/addr and the remote rkey/addr if the
length of the read is not zero. Otherwise the read response might
be treated as the RTR read response and not delivered to the
application. Or worse Terminator hardware will fail a 0B read
if the STAG is 0 even if the read length is 0.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
CM REQs cannot be successfully retried, because a new pv_cm_id is
created for each request, without checking if one already exists.
By checking if an id exists before creating one, the bug is fixed.
This bug can be provoked by running an RDMA CM user-land application,
but inserting a five seconds delay before the rdma_accept() call on
the passive side. This delay is larger than the default CMA timeout,
and triggers a retry from the active side. The retried REQ will use
another pv_cm_id (the cm_id on the wire). This confuses the CM
protocol and two REJs are sent from the passive side.
Here is an excerpt from ibdump running without the patch:
3.285092 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
7.382711 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
7.382861 LID: 4 -> LID: 4 InfiniBand 290 CM: ConnectReject
7.387644 LID: 4 -> LID: 4 InfiniBand 290 CM: ConnectReject
and here is the same with bug fix applied:
3.251010 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
7.349387 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
8.258443 LID: 4 -> LID: 4 SDP 290 CM: ConnectReply(SDP Hello)
8.259890 LID: 4 -> LID: 4 InfiniBand 290 CM: ReadyToUse
Suggested-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reported-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Tested-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Current computation of qp->timeout_jiffies in rvt_modify_qp() will cause
overflow due to the fact that the input to the function usecs_to_jiffies
is only 32-bit ( unsigned int). Overflow will occur when attr->timeout is
equal to or greater than 30. The consequence is unnecessarily excessive
retry and thus degradation of the system performance.
This patch fixes the problem by limiting the input to 5-bit and calling
usecs_to_jiffies() before multiplying the scaling factor.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Delete unused variables to prevent sparse warnings.
Fixes: db1b5ddd5336 ("IB/core: Rename uverbs event file structure")
Fixes: fd3c7904db6e ("IB/core: Change idr objects to use the new schema")
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Local ack delay exposed by the driver is 0 which means infinite QP
timeout. Reporting the default value to 16 (approx 260ms)
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
While invoking the req_notify_cq hook, ULPs can request
whether the CQs have any CQEs pending. If CQEs are pending,
drivers can indicate it by returning 1 for req_notify_cq.
The stack will poll CQ again till CQ is empty.
This patch peeks the CQ for any valid entries and return accordingly.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Fix the incorrect reporting of number of polled
entries by taking into account the max CQ depth
in the driver.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Driver shall check if the host system bios has enabled
Atomic operations capability in PCI Device Control 2
register of the pci-device. Expose the ATOMIC_HCA
flag only if the Atomic operations capability is set.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Starting FW version 20.6.47, firmware is keeping separate statistics
for L2 and RDMA. However, driver needs to specify RDMA or not when
allocating stat_ctx.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There's a couple of bugs in the support of max_rd_atomic and
max_dest_rd_atomic. In the modify_qp, if the requested max_rd_atomic,
which is the ORRQ size, is greater than what the chip can support,
then we have to cap the request to chip max as we can't have the HW
overflow the ORRQ. Capping the max_rd_atomic support internally is okay
to do as the remaining read/atomic WRs will still be sitting in the SQ.
However, for the max_dest_rd_atomic, the driver has to error out as
this dictates the IRRQ size and we can't control what the remote
side sends.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
- Report supported value for max_mr_size to IB stack in query_device.
Also, check and log if MR size requested by application in
reg_user_mr() is greater than value currently supported by driver.
- Report only 4K page size support for now
- Fix Max_QP value returned by ibv_devinfo -vv.
In case of PF, FW reserves 129 QPs for creating QP1s of VFs
and PF. So the max_qp value reported by FW for PF doesn'tt include
the QP1. Fixing this issue by adding 1 with the value reported
by FW.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This fix is added only to avoid system crash in some a
specific scenario. When bnxt_re driver is loaded and if
user tries to change interface mac address, delete GID
fails because QP1 is still associated with existing MAC
(default GID). If the above command fails GID tables are
not modified in the h/w or driver, but the GID context memory
is freed. Now, if the user changes the mac back to the original
value, another add_gid comes to the driver where the driver
reports that the GID is already present in its table
and tries to access the context which was already freed.
So, in this case, in order to avoid NULL pointer de-reference,
this patch removes the context memory free if delete_gid fails
and the same context memory is re-used in new add_gid.
Memory cleanup will be taken care during driver unload, while
deleting the GID table.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Posting WQE size of 2 results in a WQE_FORMAT_ERROR
thrown by the HW as it requires host to supply WQE Size with room
for atleast one SGE so that the resulting WQE size be atleast 3.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The driver must free the DPI during the dealloc_ucontext
instead of freeing it during dealloc_pd. However, the DPI
allocation scheme remains unchanged.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
"umem" is a valid pointer. We intended to print "*umem" or even just
"err" instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
If either of these allocations fail then we return ERR_PTR(0). That's
equivalent to NULL and results in a NULL pointer dereference in the
caller.
Fixes: fe2caefcdf58 ("RDMA/ocrdma: Add driver for Emulex OneConnect IBoE RDMA adapter")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
We should preserve the original "status" error code instead of resetting
it to zero. Returning ERR_PTR(0) is the same as NULL and results in a
NULL dereference in the callers. I added a printk() on error instead.
Fixes: 45e86b33ec8b ("RDMA/ocrdma: Cache recv DB until QP moved to RTR")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
We accidentally don't set the error code on some error paths. It means
return ERR_PTR(0) which is NULL and results in a NULL dereference in the
caller.
Fixes: 13a239330abd ("RDMA/cxgb3: Don't ignore insert_handle() failures")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
If one of these kmalloc() calls fails then we return ERR_PTR(0) which is
NULL. It results in a NULL dereference in the callers.
Fixes: cfdda9d76436 ("RDMA/cxgb4: Add driver for Chelsio T4 RNIC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
We accidentally forgot to set the error code if ib_copy_from_udata()
fails. It means we return ERR_PTR(0) which is NULL and results in a
NULL dereference in the callers.
Fixes: d37498417947 ("i40iw: add files for iwarp interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
We accidentally don't see the error code on some of these error paths.
It means we return ERR_PTR(0) which is NULL and it results in a NULL
dereference in the caller.
This bug dates to pre-git days.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
bnxt_re_alloc_mw() doesn't return NULL, it returns error pointers.
Fixes: 9152e0b722b2 ("RDMA/bnxt_re: HW workarounds for handling specific conditions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
If the physical buffer list entries (PBLEs) of a QP are freed
up at i40iw_dereg_mr, they can be assigned to a newly
created QP before the previous QP is destroyed. Fix this
by freeing PBLEs only when the QP is destroyed.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Control Queue Pair (CQP) request objects, which have
not received a completion upon interface close, remain
in memory.
To fix this, identify and free all pending CQP request
objects during destroy CQP OP.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
To avoid infinite loop, in i40iw_ieq_handle_exception, update
plist inside while loop.
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add missing write memory barrier before writing the
header containing valid bit to the WQE in i40iw_puda_send.
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Current flow leaves software QP structures in memory if
Control Queue Pair (CQP) destroy QP OP fails. To fix this,
free QP resources on fail of CQP destroy QP OP.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
On PCI function reset, cm_id reference is not released
which causes an application hang, as it waits on the
cm_id to be released on rdma_destroy.
To fix this, call i40iw_cm_disconn during a PCI function
reset to clean-up resources and release cm_id reference.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Utilize iwdev->reset on a PCI function reset notification
instead of passing in reset flag for resource clean-up.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Control Queue Pair (CQP) OPs, in this case - Update SDs,
cannot poll the Control Completion Queue (CCQ) after CCQ is
destroyed. Instead, poll via registers.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The order for calling i40iw_destroy_pble_pool is incorrect.
Also, add PBLE_CHUNK_MEM init state to track pble pool
creation and destruction.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Playing with IP-O-IB interface can trigger a warning message:
"ib0: Failed to modify QP to ERROR state" to be logged.
This happens when the QP is in IB_QPS_RESET state and the stack
is trying to transition it to IB_QPS_ERR state in ipoib_ib_dev_stop().
According to the IB spec, Table 91 - "QP State Transition Properties"
it looks like the transition from reset to error is valid:
Transition: Any State to Error
Required Attributes: None
Optional Attributes: None allowed
Actions: Queue processing is stopped. Work Requests pending or in
process are completed in error, when possible.
This patch allows the transition and quiets the message.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch correct the comment style warnings caught by
checkpatch.pl script.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When modified the MAC address used hns_roce_mac function, we release and create
reserved qp again, It is not necessary to use spin_lock_bh and spin_unlock_bh in
handle_en_event, Otherwise, it will occur a error. This patch mainly fixes it.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When opcode of work request is RDMA read and write, it
should use rdma_wr to get remote_addr and rkey. This
patch fixes it.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When destroyed rc qp, the hr_qp will be used after freed. This patch
will fix it.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In hip06 SoC, RoCE driver creates 8 reserved loopback QPs to
ensure zero wqe when free mr. However, if the enabled phy
port number is less than 6, it will fail in polling cqe with
8 reserved loopback QPs.
In order to solve this problem, the number of loopback Qps
will be adjusted based on the number of enabled phy port.
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The RXE coupled with dummy device causes to the kernel panic attached
below. The panic happens when ib_register_device tries to set dma_mask
by accessing a NULLed parent device.
The RXE does not actually use DMA, so we can set the dma_mask
to architecture value.
[16240.199689] RIP: 0010:ib_register_device+0x468/0x5a0 [ib_core]
[16240.205289] RSP: 0018:ffffc9000220fc10 EFLAGS: 00010246
[16240.209909] RAX: 0000000000000024 RBX: ffff880220d1a2a8 RCX: 0000000000000000
[16240.212244] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000009
[16240.214385] RBP: ffffc9000220fcb0 R08: 0000000000000000 R09: 000000000000023f
[16240.254465] R10: 0000000000000007 R11: 0000000000000000 R12: 0000000000000000
[16240.259467] R13: 0000000000000000 R14: 0000000000000000 R15: ffff880220d1a2a8
[16240.263314] FS: 00007fd8ecca0740(0000) GS:ffff8802364c0000(0000) knlGS:0000000000000000
[16240.267292] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[16240.273503] CR2: 0000000000000218 CR3: 00000002253ba000 CR4: 00000000000006e0
[16240.277066] Call Trace:
[16240.281836] ? __kmalloc+0x26f/0x280
[16240.286596] rxe_register_device+0x297/0x300 [rdma_rxe]
[16240.291377] rxe_add+0x535/0x5b0 [rdma_rxe]
[16240.297586] rxe_net_add+0x3e/0xc0 [rdma_rxe]
[16240.302375] rxe_param_set_add+0x65/0x144 [rdma_rxe]
[16240.307769] param_attr_store+0x68/0xd0
[16240.311640] module_attr_store+0x1d/0x30
[16240.316421] sysfs_kf_write+0x3a/0x50
[16240.317802] kernfs_fop_write+0xff/0x180
[16240.322989] __vfs_write+0x37/0x140
[16240.328164] ? handle_mm_fault+0xce/0x240
[16240.333340] vfs_write+0xb2/0x1b0
[16240.335013] SyS_write+0x55/0xc0
[16240.340632] entry_SYSCALL_64_fastpath+0x1a/0xa9
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In the time between rxe_send has finished and skb destructor
called, the QP's ref count might be 0, leading to a possible
QP destruction. This will lead to a kernel panic when the destructor
dereferences the QP.
The operation of incrementing QP ref count at rxe_send and decrementing
from skb destructor will prevent this crash.
BUG: unable to handle kernel NULL pointer dereference at 000000000000072c
IP: [<ffffffffa05df765>] rxe_skb_tx_dtor+0x15/0x50 [rdma_rxe]
PGD 0 [16240.211178]
Oops: 0002 [#1] SMP
CPU: 3 PID: 0 Comm: swapper/3 Tainted: G OE 4.9.0-mlnx #1
Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011
task: ffff88042d6b1480 task.stack: ffffc90001904000
RIP: 0010:[<ffffffffa05df765>] [<ffffffffa05df765>] rxe_skb_tx_dtor+0x15/0x50 [rdma_rxe]
RSP: 0018:ffff88043fcc3df0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff880429684700 RCX: ffff88042d248200
RDX: 00000000ffffffff RSI: 00000000fffffe01 RDI: ffff880429684700
RBP: ffff88043fcc3e00 R08: ffff88043fcda240 R09: 00000000ff2d1de6
R10: 0000000000000000 R11: 00000000f49cf6fe R12: ffff880429684700
R13: ffffffff81893f96 R14: ffffffff817d66f0 R15: ffff880427f74200
FS: 0000000000000000(0000) GS:ffff88043fcc0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000072c CR3: 000000041d3df000 CR4: 00000000000006e0
Stack:
ffffffff817b29cf ffff880429684700 ffff88043fcc3e18 ffffffff817b42c2
ffff880429684700 ffff88043fcc3e40 ffffffff817b4332 ffff880429684700
ffff880427f74238 ffff880427f74228 ffff88043fcc3e58 ffffffff81893f96
Call Trace:
<IRQ> [16240.336345] [<ffffffff817b29cf>] ? skb_release_head_state+0x4f/0xb0
[<ffffffff817b42c2>] skb_release_all+0x12/0x30
[<ffffffff817b4332>] kfree_skb+0x32/0x90
[<ffffffff81893f96>] ndisc_error_report+0x36/0x40
[<ffffffff817d4de1>] neigh_invalidate+0x81/0xf0
[<ffffffff817d68f7>] neigh_timer_handler+0x207/0x2b0
[<ffffffff81109295>] call_timer_fn+0x35/0x120
[<ffffffff81109db7>] run_timer_softirq+0x1d7/0x460
[<ffffffff8106155e>] ? kvm_sched_clock_read+0x1e/0x30
[<ffffffff810366b9>] ? sched_clock+0x9/0x10
[<ffffffff810cfed2>] ? sched_clock_cpu+0x72/0xa0
[<ffffffff818dd537>] __do_softirq+0xd7/0x289
[<ffffffff810a6c95>] irq_exit+0xb5/0xc0
[<ffffffff818dd372>] smp_apic_timer_interrupt+0x42/0x50
[<ffffffff818dc682>] apic_timer_interrupt+0x82/0x90
<EOI> [16240.395776] [<ffffffff818da156>] ? native_safe_halt+0x6/0x10
[<ffffffff818d9e6e>] default_idle+0x1e/0xd0
[<ffffffff8103797f>] arch_cpu_idle+0xf/0x20
[<ffffffff818da2c5>] default_idle_call+0x35/0x40
[<ffffffff810e3eb5>] cpu_startup_entry+0x185/0x210
[<ffffffff81050433>] start_secondary+0x103/0x130
RIP [<ffffffffa05df765>] rxe_skb_tx_dtor+0x15/0x50 [rdma_rxe]
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The driver checks if the lower level driver supports get_stats, and if
so calls it to get the updated statistics, otherwise takes from the
current netdevice stats object.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Currently the RoCE GID management uses the ib_wq to do add and delete new GIDs
according to the netdev events.
The ib_wq isn't an ordered workqueue and thus two work elements can be executed
concurrently which will result in unexpected behavior and inconsistency of the
GIDs cache content.
Example:
ifconfig eth1 11.11.11.11/16 up
This command will invoke the following netdev events in the following order:
1. NETDEV_UP
2. NETDEV_DOWN
3. NETDEV_UP
If (2) and (3) will be executed concurrently or in reverse order, instead of
having a new GID with 11.11.11.11 IP, we will end up without any new GIDs.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The failure in creation of debugfs entries for mr_cache left entries,
which were already created.
It caused to mismatch and misguiding for the end users. The solution
is to clean mr_cache debugfs root, so no leftovers will be in the
system. In addition, let's document why the error is not needed to be
forwarded to user in case of failure.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The caller to the driver marks GFP_NOIO allocations with help
of memalloc_noio-* calls now. This makes redundant to pass down
to the driver gfp flags, which can be GFP_KERNEL only.
The patch removes the gfp flags argument and updates all driver paths.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The caller to the driver marks GFP_NOIO allocations with help
of memalloc_noio-* calls now. This makes redundant to pass down
to the driver gfp flags, which can be GFP_KERNEL only.
The patch removes the gfp flags argument and updates all driver paths.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Commit 21caf2fc1931 ("mm: teach mm by current context info to not do I/O
during memory allocation") added the memalloc_noio_(save|restore) functions
to enable people to modify the MM behavior by disabling I/O during memory
allocation. This was further extended in Fixes: 934f3072c17c ("mm: clear
__GFP_FS when PF_MEMALLOC_NOIO is set"). memalloc_noio_* functions prevent
allocation paths recursing back into the filesystem without explicitly
changing the flags for every allocation site.
However the IPoIB hasn't been keeping up with the changes and missed
completely these memalloc_noio_* calls. This led to update of
allocation site with special QP creation flag, see commit 09b93088d750
("IB: Add a QP creation flag to use GFP_NOIO allocations"), while this
flag is supported by small number of drivers in IB stack.
Let's change it by updating to memalloc_noio_* calls and allow
for every driver underneath enjoy NOIO allocations.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch checks if there is a driver below that
needs to be updated on the new MTU and calls it
accordingly.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The msleep(1) may do not sleep 1 ms as expected
and will sleep longer. The simple conversion from
msleep to usleep_range between 1ms and 2ms can solve an
issue.
The full and comprehensive explanation can be found at [1] and [2].
[1] https://lkml.org/lkml/2007/8/3/250
[2] Documentation/timers/timers-howto.txt
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch makes use of IB core's ib_modify_qp_with_udata function that
also resolves the DMAC and handles udata.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch adds new function ib_modify_qp_with_udata so that
uverbs layer can avoid handling L2 mac address at verbs layer
and depend on the core layer to resolve the mac address consistently
for all required QPs.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When resolving an IP address that is on the host of the caller the
result from querying the routing table is the loopback device. This is
not a valid response, because it doesn't represent the RDMA device and
the port.
Therefore, callers need to check the resolved device and if it is a
loopback device find an alternative way to resolve it. To avoid this we
make sure that the response from rdma_resolve_ip() will not be the
loopback device.
While that, we fix an static checker warning about dereferencing an
unintitialized pointer using the same solution as in commit abeffce90c7f
("net/mlx5e: Fix a -Wmaybe-uninitialized warning") as a reference.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
