Age | Commit message (Collapse) | Author |
|
"flash" is a very generic name for a platform_driver that is only
available on SA11x0.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nicolas Pitre <nico@marvell.com>
|
|
Currently we use a spin-lock to serialise statistics fetches and also
to inhibit them for short periods of time, plus a flag to
enable/disable statistics fetches for longer periods of time, during
online reset. This was apparently insufficient to deal with the several
reasons for stats being disabled.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All 10Xpress PHYs require autonegotiation all the time; enforce this
in the set_settings() method and do not treat it as a workaround.
Remove claimed support for 100M HD mode since it is not supported by
current firmware.
Do not set speed override bits when AN is enabled, and do not use
register 1.49192 for AN configuration as it can override what we set
elsewhere.
Always set the AN selector bits to 1 (802.3).
Fix confusion between Next Page and Extended Next Page.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This workaround is not specific to rev A.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depending on the loopback mode, there may be no pertinent link state
bits. In this case we test the PHYXS RX fault bit instead. Make
sure to do this in all cases where there are no link state bits.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In particular, set pause advertising bits properly.
A PHY reset is not necessary to recover from the register self-test,
so use a "invisible" reset there instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify falcon_switch_mac() to always set NIC_STAT_REG, even if the the
MAC is the same as it was before. This ensures that the value is
correct after an online reset.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change sfn4111t_reset() to change only GPIO output enables so that it
doesn't break subsequent I2C operations.
Update comments to explain exactly what we're doing.
Add a short sleep to make sure the FLASH_CFG_1 value is latched before
any subsequent I2C operations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of disabling AN in loopback, just prevent restarting AN and
override the speed in sft9001_get_settings().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Early versions of the SFX7101 firmware could complete link training in
a state where it would not adequately cancel noise (Solarflare bug
10750). We previously worked around this by resetting the PHY after
seeing many Ethernet CRC errors. This workaround is unsafe since it
takes no account of the interval between errors; it also appears to
be unnecessary with production firmware. Therefore remove it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable a firmware option that appears to be necessary for reliable
operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Printing anything over netconsole before hw is up and running is,
of course, not going to work.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix bounds checking of wm8350->pmic.led
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
This workaround was needed when regulator/ was not linked before both
power/ and usb/otg/ in drivers/Makefile. Now that it is even linked
before mfd/, this patch makes sure that bq24022 isn't probed before the
GPIO expander is set up.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
tulip: fix 21142 with 10Mbps without negotiation
drivers/net/skfp: if !capable(CAP_NET_ADMIN): inverted logic
gianfar: Fix Wake-on-LAN support
smsc911x: timeout reaches -1
smsc9420: fix interrupt signalling test failures
ucc_geth: Change uec phy id to the same format as gianfar's
wimax: fix build issue when debugfs is disabled
netxen: fix memory leak in drivers/net/netxen_nic_init.c
tun: Add some missing TUN compat ioctl translations.
ipv4: fix infinite retry loop in IP-Config
net: update documentation ip aliases
net: Fix OOPS in skb_seq_read().
net: Fix frag_list handling in skb_seq_read
netxen: revert jumbo ringsize
ath5k: fix locking in ath5k_config
cfg80211: print correct intersected regulatory domain
cfg80211: Fix sanity check on 5 GHz when processing country IE
iwlwifi: fix kernel oops when ucode DMA memory allocation failure
rtl8187: Fix error in setting OFDM power settings for RTL8187L
mac80211: remove Michael Wu as maintainer
...
|
|
This fixes a crash observed when non-existant enable_ms function is
called for jsm driver.
Signed-off-by: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Paul Larson <pl@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit e57db7b (SATA Sil: Blacklist system that spins off disks during ACPI power off)
breaks build like the following, in both cases when CONFIG_DMI set or not.
drivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a cast
sata_sil.c should include dmi.h
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move DMA-mapping.txt to Documentation/PCI/.
DMA-mapping.txt was supposed to be moved from Documentation/ to
Documentation/PCI/. The 00-INDEX files in those two directories
were updated, along with a few other text files, but the file
itself somehow escaped being moved, so move it and update more
text files and source files with its new location.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: poch: fix verification of memory area
Staging: usbip: usbip_start_threads(): handle kernel_thread failure
staging: agnx: drivers/staging/agnx/agnx.h needs <linux/io.h>
Staging: android: task_get_unused_fd_flags: fix the wrong usage of tsk->signal
Staging: android: Add lowmemorykiller documentation.
Staging: android: fix build error on 64bit boxes
Staging: android: timed_gpio: Fix build to build on kernels after 2.6.25.
Staging: android: binder: fix arm build errors
Staging: meilhaus: fix Kbuild
Staging: comedi: fix Kbuild
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver-core: fix kernel-doc parameter name
UIO: Add missing documentation of features added recently
Sync patch for jp_JP/stable_kernel_rules.txt
|
|
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: allow direct user-space I/O
UBI: fix resource de-allocation
UBI: remove unused variable
UBI: use nicer 64-bit math
UBI: add ioctl compatibility
UBI: constify file operations
UBI: allow all ioctls
UBI: remove unnecessry header inclusion
UBI: improve ioctl commentaries
UBI: add ioctl for is_mapped operation
UBI: add ioctl for unmap operation
UBI: add ioctl for map operation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: document difference between hid_blacklist and hid_ignore_list
HID: add antec-branded soundgraph imon devices to blacklist
HID: fix reversed logic in disconnect testing of hiddev
HID: adjust report descriptor fixup for MS 1028 receiver
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: Fix a memory leak with the lg object during launcher close
lguest: disable the FORTIFY for lguest.
lguest: typos fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: sbp2: add workarounds for 2nd and 3rd generation iPods
firewire: sbp2: add workarounds for 2nd and 3rd generation iPods
firewire: sbp2: fix DMA mapping leak on the failure path
firewire: sbp2: define some magic numbers as macros
firewire: sbp2: fix payload limit at S1600 and S3200
ieee1394: sbp2: don't assume zero model_id or firmware_revision if there is none
ieee1394: sbp2: fix payload limit at S1600 and S3200
ieee1394: sbp2: update a help string
ieee1394: support for speeds greater than S800
firewire: core: optimize card shutdown
ieee1394: ohci1394: increase AT req. retries, fix ack_busy_X from Panasonic camcorders and others
firewire: ohci: increase AT req. retries, fix ack_busy_X from Panasonic camcorders and others
firewire: ohci: change "context_stop: still active" log message
firewire: keep highlevel drivers attached during brief connection loss
firewire: unnecessary BM delay after generation rollover
firewire: insist on successive self ID complete events
|
|
s/unlock/lock/
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=12575
Reported-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If the initial state is not set when the input device is set up, the first
docking event after the module is loaded will be lost.
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
MacPro 3 have more temperature sensors than the previous MacPro's also the
sensor THTG has been removed. This patch add supports for the newer
temperature sensors in the MacPro3.
Signed-off-by: Bharath Ramesh <bramesh@vt.edu>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Bump hpilo module version to indicate that the open/close bug is fixed.
Signed-off-by: David Altobelli <david.altobelli@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Error was introduced in commit fe8e4e039dc3 ("hp-wmi: handle
rfkill_register() failure").
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix request-already-requested handling in gpio_request().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Clean up the stale DBUG_ON checks and add a couple new ones.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If the bte copy fails, the attempt to retrieve payloads merely returns a
null pointer deref and not NULL as was expected.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The clearing of the msg->flags needs a barrier between it and the notify
of the channel threads that the messages are cleaned and ready for use.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
with current kernels, tulip 21142 ethernet controllers fail to connect
to a 10Mbps only (i.e. without negotiation-partner) network. It used
to work in 2.4 kernels. Fix that. Tested on a 21142 Rev 0x11.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix inverted logic
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 0f0ca340e57bd7446855fefd07a64249acf81223 ("phy: power
management support") caused a regression in the gianfar driver.
Now phylib turns off PHY power during suspend, and thus WOL
doesn't work anymore.
This patch workarounds the issue by enabling wakeup in the MDIO
device, i.e. just restores the old behaviour for the gianfar
driver. Note that this way all PHYs on a given MDIO bus won't
be turned off during suspend, which isn't good from the power
saving point of view.
A proper, per netdevice wakeup management support will need
a bit reworked phylib suspend/resume logic.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With a postfix decrement the timeout will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smsc9420 performs an interrupt signalling test when the interface is
brought up. The current code mistakenly sets its test flag to false
AFTER enabling the software interrupt source, making failure quite
likely.
This patch changes the code to set the test flag BEFORE enabling
interrupts. I've also removed an smp_wmb because the following spinlock
provides an implicit memory barrier.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit b31a1d8b41513b96e9c7ec2f68c5734cef0b26a4 ("gianfar: Convert
gianfar to an of_platform_driver") changes the gianfar's phy id to the
format like "mdio@xxxx:xx", but uec still uses the old format like
"xxxxxxxx:xx". For the board whose UEC uses gianfar-mdio like
MPC8568MDS, the phy can not be attached because of the incompatible
phy id format. This patch changes uec's phy id to the same format as
gianfar's.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As reported by Toralf Förster and Randy Dunlap.
- http://linuxwimax.org/pipermail/wimax/2009-January/000460.html
- http://lkml.org/lkml/2009/1/29/279
The definitions needed for the wimax stack and i2400m driver debug
infrastructure was, by mistake, compiled depending on CONFIG_DEBUG_FS
(by them being placed in the debugfs.c files); thus the build broke in
2.6.29-rc3 when debugging was enabled (CONFIG_WIMAX_DEBUG) and
DEBUG_FS was disabled.
These definitions are always needed if debug is enabled at compile
time (independently of DEBUG_FS being or not enabled), so moving them
to a file that is always compiled fixes the issue.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a memory leak identified by Rusty Russell during LCA09 by
kfree'ing the lg object instead of just clearing it when the
launcher closes.
Signed-off-by: Mark Wallis <mwallis@serialmonkey.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
3 points
lguest_asm.S => i386_head.S
LHCALL_BREAK => LHREQ_BREAK
perferred => preferred
Signed-off-by: Atsushi SAKAI <sakaia@jp.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
For kernel bugzilla #12537:
http://bugzilla.kernel.org/show_bug.cgi?id=12537
Free memory.
Signed-off-by: Daniel Marjamäki <danielm77@spray.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reducing jumbo ring size below 1024 reduces throughput for old
firmwares (3.4.216 and older) running on older (NX2031) chip,
so restore it back to 1024.
This was reduced in commit 32ec803348b4d5f1353e1d7feae30880b8b3e342
("netxen: reduce memory footprint").
Raising jumbo ring size from 512 to 1024, adds ~4MB per port, but
there's still big saving because of original patch (~20MB per port).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
ath5k_config updates the software context without taking sc->lock.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The patch fixes memcpy to NULL address when the ucode DMA allocation failure.
This is a fix to bug
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1861
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
After reports of poor performance, a review of the latest vendor driver
(rtl8187_linux_26.1025.0328.2007) for RTL8187L devices was undertaken.
A difference was found in the code used to index the OFDM power tables. When
the Linux driver was changed, my unit works at a much greater range than
before. I think this fixes Bugzilla #12380 and has been tested by at least
two other users.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Martín Ernesto Barreyro <barreyromartin@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|