| Age | Commit message (Collapse) | Author |
|---|
|
http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: PXA: fix includes in pxa2xx_cm_x2xx PCMCIA driver
ARM: PXA: fix gpio-pxa.h build errors
ARM: 7142/1: davinci: mark GPIO implementation complex
ARM: 7134/1: Revert "EXYNOS4: Fix routing timer interrupt to offline CPU"
ARM: PXA: eseries: fix eseries_register_clks section mismatch warning
ARM: PXA: fix lubbock PCMCIA driver build error
|
|
Use kstrdup rather than duplicating its implementation
The semantic patch that makes this output is available
in scripts/coccinelle/api/kstrdup.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Commit 2265cef2 (hwmon: (w83627ehf) Properly report PECI and AMD-SI
sensor types) results in kernel panic if data->temp_label was not
initialized.
The problem was found with chip W83627DHG-P.
Add check if data->temp->label was set before use.
Based on incomplete patch by Alexander Beregalov.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The definition of TO_ATTR_NO in the non-SMP case is wrong. As the SMP
definition resolves to the correct value, just use this for both
cases.
Without this fix the temperature attributes are named temp0_* instead
of temp2_*, so libsensors won't pick them. Broken since kernel 3.0.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Phil Sutter <phil@nwl.cc>
Cc: stable@kernel.org
Acked-by: Durgadoss R <Durgadoss.r@intel.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
* 'next/devel2' of git://git.linaro.org/people/arnd/arm-soc: (30 commits)
ARM: mmp: register internal sram bank
ARM: mmp: register audio sram bank
ARM: mmp: add sram allocator
gpio/samsung: Complain loudly if we don't know the SoC
ARM: S3C64XX: Fix SoC identification for S3C64xx devices
ARM: S3C2443: Remove redundant s3c_register_clocks call for init_clocks
ARM: S3C24XX: Add devname for hsmmc1 pclk
ARM: S3C24XX: use clk_get_rate to init fclk in common_setup_clocks
ARM: S3C2443: Accommodate cpufreq frequency scheme in armdiv
ARM: S3C2443: handle unset armdiv values gracefully
ARM: S3C2443: Add get_rate operation for clk_armdiv
ARM: S3C2416: Add comment describing the armdiv/armclk
ARM: S3C2443: Move clk_arm and clk_armdiv to common code
ARM: S3C24XX: Add infrastructure to transmit armdiv to common code
ARM: S3C2416: Add armdiv_mask constant
ARM: EXYNOS4: Add support for M-5MOLS camera on Nuri board
ARM: EXYNOS4: Enable MFC on ORIGEN
ARM: SAMSUNG: Add support s3c2416-adc for S3C2416/S3C2450
ARM: SAMSUNG: Add support s3c2443-adc for S3C2443
ARM: SAMSUNG: Allow overriding of adc device name for S3C24XX
...
|
|
* 'next/cleanup3' of git://git.linaro.org/people/arnd/arm-soc: (79 commits)
ARM: SAMSUNG: Move fimc plat. device from board files to plat-samsung
ARM: SAMSUNG: Cleanup resources by using macro
ARM: SAMSUNG: Cleanup plat-samsung/devs.c and devs.h
ARM: S5P: To merge devs.c files to one devs.c
ARM: S3C64XX: To merge devs.c files to one devs.c
ARM: S3C24XX: To merge s3c24xx devs.c files to one devs.c
ARM: S5P64X0: Add Power Management support
ARM: S5P: Make the sleep code common for S5P series SoCs
ARM: S5P: Make the common S5P PM code conditionally compile
ARM: SAMSUNG: Move S5P header files to plat-samsung
ARM: SAMSUNG: Move S3C24XX header files to plat-samsung
ARM: SAMSUNG: Moving each SoC support header files
ARM: SAMSUNG: Consolidate plat/pll.h
ARM: SAMSUNG: Consolidate plat/pwm-clock.h
ARM: SAMSUNG: Cleanup mach/clkdev.h
ARM: SAMSUNG: remove sdhci default configuration setup platform helper
ARM: EXYNOS4: Add FIMC device on SMDKV310 board
ARM: EXYNOS4: Add header file protection macros
ARM: EXYNOS4: Add usb ehci device to the SMDKV310
ARM: S3C2443: Add hsspi-clock from pclk and rename S3C2443 hsspi sclk
...
Fix up conflicts in
- arch/arm/mach-exynos4/{Kconfig,clock.c}
ARM_CPU_SUSPEND, various random device tables (gah!)
- drivers/gpio/Makefile
sa1100 gpio added, samsung gpio drivers merged
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Freezer: Revert 27920651fe "PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too"
PM / Freezer: Reimplement wait_event_freezekillable using freezer_do_not_count/freezer_count
USB: Update last_busy time after autosuspend fails
PM / Runtime: Automatically retry failed autosuspends
PM / QoS: Remove redundant check
PM / OPP: Fix build when CONFIG_PM_OPP is not set
PM / Runtime: Fix runtime accounting calculation error
PM / Sleep: Update freezer documentation
PM / Sleep: Remove unused symbol 'suspend_cpu_hotplug'
PM / Sleep: Fix race between CPU hotplug and freezer
ACPI / PM: Add Sony VPCEB17FX to nonvs blacklist
|
|
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: Convert wm831x driver to watchdog core
watchdog: s3c2410: convert to use the watchdog framework
Documentation: watchdog: add guide how to convert drivers to new framework
watchdog: iTCO_wdt.c - problems with newer hardware due to SMI clearing
watchdog: Add WDIOC_GETTIMELEFT ioctl support to w83627 watchdog driver
watchdog: irq: Remove IRQF_DISABLED
watchdog: Octeon: Mark octeon_wdt interrupt as IRQF_NO_THREAD
watchdog: sc520_wdt: Remove unnecessary cast.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (45 commits)
[SCSI] Fix block queue and elevator memory leak in scsi_alloc_sdev
[SCSI] scsi_dh_alua: Fix the time inteval for alua rtpg commands
[SCSI] scsi_transport_iscsi: Fix documentation os parameter
[SCSI] mv_sas: OCZ RevoDrive3 & zDrive R4 support
[SCSI] libfc: improve flogi retries to avoid lport stuck
[SCSI] libfc: avoid exchanges collision during lport reset
[SCSI] libfc: fix checking FC_TYPE_BLS
[SCSI] edd: Treat "XPRS" host bus type the same as "PCI"
[SCSI] isci: overriding max_concurr_spinup oem parameter by max(oem, user)
[SCSI] isci: revert bcn filtering
[SCSI] isci: Fix hard reset timeout conditions.
[SCSI] isci: No need to manage the pending reset bit on pending requests.
[SCSI] isci: Remove redundant isci_request.ttype field.
[SCSI] isci: Fix task management for SMP, SATA and on dev remove.
[SCSI] isci: No task_done callbacks in error handler paths.
[SCSI] isci: Handle task request timeouts correctly.
[SCSI] isci: Fix tag leak in tasks and terminated requests.
[SCSI] isci: Immediately fail I/O to removed devices.
[SCSI] isci: Lookup device references through requests in completions.
[SCSI] ipr: add definitions for additional adapter
...
|
|
The includes in the pxa2xx_cm_x2xx PCMCIA driver are rather random;
the driver doesn't require anything from these headers except the
cpu_is_xxx() macros which come from another include.
The concern is that it's getting these definitions via mach/system.h,
which is supposed to only be included by arch/arm/kernel/process.c.
As this header is scheduled for cleanup (and elimination) keeping
the status quo will cause build errors. So lets fix properly and
independent of the future work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fairly large code churn but not much doing with that and the overall
result is a definite win.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Make this driver a user of the watchdog framework and remove now
centrally handled parts. Tested on a mini2440.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Redhat Bugzilla: Bug 727875 - TCO_EN bit is disabled by TCO driver
Jiri Slaby: 28d41f53f broke temperature sensors on a ICH10 chipset
The iTCO_wdt driver disables the SMI. This breaks good working of newer hardware.
The disabling of the SMI by the TCO logic dates back from the i810-tco driver
from Nils Faerber (around 28 July 2000). The reason for this was that some BIOSes
install handlers reset or disable the watchdog timer instead of resetting the system.
The trick to fix this was to disable the SMI (by clearing the SMI_TCO_EN bit of the
SMI_EN register) to prevent this from happening.
This however has strange effects on newer hardware. So we are in a situation that
a fix for broken old hardware affects newer hardware.
The correct solution is to make this fix an option (with the new module parameter:
turn_SMI_watchdog_clear_off) so that the default behaviour is the unfixed version.
the next patch will be to move this in the start and stop functions of the driver
and to add a new module parameter for the global_smi_en bit and to get rid of the
vendor_support code.
This fix can have an effect on old (typical ICH & ICH2 chipsets) motherboards that
have a broken BIOS implementation concerning TCO logic. In these case the module
parameter turn_SMI_watchdog_clear_off=1 will need to be added.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add WDIOC_GETTIMELEFT ioctl allowing you to check how much time is left
on the watchdog counter before a reset occurs.
Signed-off-by: Greg Lee <glee [at] swspec.com>
Signed-off-by: Padraig Brady <P@draigbrady.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@google.com>
|
|
This flag is a NOOP and can be removed now.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This is to exclude it from force threading to allow RT patch set to work.
The watchdog timers are per-CPU and the addresses of register that reset
the timer are calculated based on the current CPU. Therefore we cannot
allow it to run on a thread on a different CPU. Also we only do a
single register write, which is much faster than scheduling a handler
thread.
And while on this line remove IRQF_DISABLED as this flag is a NOP.
Signed-off-by: Venkat Subbiah<venkat.subbiah@cavium.com>
Acked-by: David Daney<david.daney@cavium.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Fix:
ERROR: "pxa2xx_configure_sockets" [drivers/pcmcia/pxa2xx_lubbock_cs.ko] undefined!
by exporting the required function.
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (63 commits)
dmaengine: mid_dma: mask_peripheral_interrupt only when dmac is idle
dmaengine/ep93xx_dma: add module.h include
pch_dma: Reduce wasting memory
pch_dma: Fix suspend issue
dma/timberdale: free_irq() on an error path
dma: shdma: transfer based runtime PM
dmaengine: shdma: protect against the IRQ handler
dmaengine i.MX DMA/SDMA: add missing include of linux/module.h
dmaengine: delete redundant chan_id and chancnt initialization in dma drivers
dmaengine/amba-pl08x: Check txd->llis_va before freeing dma_pool
dmaengine/amba-pl08x: Add support for sg len greater than one for slave transfers
serial: sh-sci: don't filter on DMA device, use only channel ID
ARM: SAMSUNG: Remove Samsung specific enum type for dma direction
ASoC: Samsung: Update DMA interface
spi/s3c64xx: Merge dma control code
spi/s3c64xx: Add support DMA engine API
ARM: SAMSUNG: Remove S3C-PL330-DMA driver
ARM: S5P64X0: Use generic DMA PL330 driver
ARM: S5PC100: Use generic DMA PL330 driver
ARM: S5PV210: Use generic DMA PL330 driver
...
Fix up fairly trivial conflicts in
- arch/arm/mach-exynos4/{Kconfig,clock.c}
- arch/arm/mach-s5p64x0/dma.c
|
|
* 'for-3.2/drivers' of git://git.kernel.dk/linux-block: (30 commits)
virtio-blk: use ida to allocate disk index
hpsa: add small delay when using PCI Power Management to reset for kump
cciss: add small delay when using PCI Power Management to reset for kump
xen/blkback: Fix two races in the handling of barrier requests.
xen/blkback: Check for proper operation.
xen/blkback: Fix the inhibition to map pages when discarding sector ranges.
xen/blkback: Report VBD_WSECT (wr_sect) properly.
xen/blkback: Support 'feature-barrier' aka old-style BARRIER requests.
xen-blkfront: plug device number leak in xlblk_init() error path
xen-blkfront: If no barrier or flush is supported, use invalid operation.
xen-blkback: use kzalloc() in favor of kmalloc()+memset()
xen-blkback: fixed indentation and comments
xen-blkfront: fix a deadlock while handling discard response
xen-blkfront: Handle discard requests.
xen-blkback: Implement discard requests ('feature-discard')
xen-blkfront: add BLKIF_OP_DISCARD and discard request struct
drivers/block/loop.c: remove unnecessary bdev argument from loop_clr_fd()
drivers/block/loop.c: emit uevent on auto release
drivers/block/cpqarray.c: use pci_dev->revision
loop: always allow userspace partitions and optionally support automatic scanning
...
Fic up trivial header file includsion conflict in drivers/block/loop.c
|
|
* 'for-3.2/core' of git://git.kernel.dk/linux-block: (29 commits)
block: don't call blk_drain_queue() if elevator is not up
blk-throttle: use queue_is_locked() instead of lockdep_is_held()
blk-throttle: Take blkcg->lock while traversing blkcg->policy_list
blk-throttle: Free up policy node associated with deleted rule
block: warn if tag is greater than real_max_depth.
block: make gendisk hold a reference to its queue
blk-flush: move the queue kick into
blk-flush: fix invalid BUG_ON in blk_insert_flush
block: Remove the control of complete cpu from bio.
block: fix a typo in the blk-cgroup.h file
block: initialize the bounce pool if high memory may be added later
block: fix request_queue lifetime handling by making blk_queue_cleanup() properly shutdown
block: drop @tsk from attempt_plug_merge() and explain sync rules
block: make get_request[_wait]() fail if queue is dead
block: reorganize throtl_get_tg() and blk_throtl_bio()
block: reorganize queue draining
block: drop unnecessary blk_get/put_queue() in scsi_cmd_ioctl() and blk_get_tg()
block: pass around REQ_* flags instead of broken down booleans during request alloc/free
block: move blk_throtl prototypes to block/blk.h
block: fix genhd refcounting in blkio_policy_parse_and_set()
...
Fix up trivial conflicts due to "mddev_t" -> "struct mddev" conversion
and making the request functions be of type "void" instead of "int" in
- drivers/md/{faulty.c,linear.c,md.c,md.h,multipath.c,raid0.c,raid1.c,raid10.c,raid5.c}
- drivers/staging/zram/zram_drv.c
|
|
slave->duplex is a u8 type so the in bond_info_show_slave() when we
check "if (slave->duplex == -1)", it's always false.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changes to support other Optima types, introduced an accidental
regression that caused 88E8059 to come up in 10Mbit/sec.
The Yukon Optima supports a reverse auto-negotiation feature that
was incorrectly setup, and not needed. The feature could be used to
allow wake-on-lan at higher speeds. But doing it correctly would require
other changes to initialization.
Reported-by: Pavel Mateja <pavel@netsafe.cz>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
i825xx and xscale are "sub" Kconfigs to NET_VENDOR_INTEL, so
NET_VENDOR_INTEL should contain ALL the dependencies of the
"sub" Kconfigs.
Same with 8390 is a "sub" Kconfig to NET_VENDOR_NATSEMI, so
NET_VENDOR_NATSEMI needs to contains ALL the dependencies.
Freescale Kconfig only had fs_enet as a sub Kconfig, and already
contained the needed dependencies, just cleaned up the dependencies.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When implementing VRRP v2 using macvlan several problems were
discovered. VRRP is weird in that all routers participating
in a redundant group use the same virtual MAC address.
Macvlan is a natural driver to use for this but it doesn't
work. The problem is that packets with a macvlan device's
source address are not received.
The problem is actually a regression that date back almost 2 years now.
The original problems started with:
commit 618e1b7482f7a8a4c6c6e8ccbe140e4c331df4e9
Author: Arnd Bergmann <arnd@arndb.de>
Date: Thu Nov 26 06:07:10 2009 +0000
macvlan: implement bridge, VEPA and private mode
This patches restores the original 2.6.32 behavior. Allowing multicast
packets received with the VRRP source address to be received.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the tg3 version to 3.121.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During shutdown, it is impossible to reliably disable the timer and
reset_task threads. Each thread can schedule the other, which leads to
shutdown code that chases its tail.
To fix the problem, this patch removes the ability of tg3_reset_task to
schedule a new timer thread. To support this change, tg3_timer no
longer terminates itself, but rather goes into a polling mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible for multiple threads in the tg3 driver to each attempt to
schedule a run of tg3_reset_task(). The multiple tg3_reset_task
executions could all wind up on the same queue (and execute serially) or
wind up on the queues of another processor (which could execute in
parallel). Either scenario is not what was truly desired.
This patch adds a new flag, TG3_FLAG_RESET_TASK_PENDING, and uses it to
determine whether or not to schedule another run of tg3_reset_task().
With the new flag comes two new functions to facilitate scheduling and
descheduling of tg3_reset_task().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds code to attempt to obtain the PCI function number from
the device rather than accept the number handed by the kernel. In
pass-through scenarios, the function number handed by the kernel may not
reflect the true function of the device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a bug where the irq error cleanup path did not free all
the resources it allocated.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Ben Li <benli@broadcom.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the error recovery resource unwind path, it is possible for the
driver to attempt to unmap a fragment that hadn't been mapped. This
patch fixes the problem by correcting the "last" parameter supplied.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new 4k tx bd segmentation code had a bug in the error cleanup path.
If the driver did not map all the physical fragments, the abort path
would wind up advancing the producer index beyond the point where the
setup code stopped. This would ultimately turn into a tx recovery error
where the driver would expect the skb pointer to be set when it isn't.
This patch fixes the problem, and then makes the code a little easier to
understand.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
APE mutex register blocks are shared by all ports of multiport devices.
For some mutexing purposes, each function is assigned their own
register. For other cases, each function is assigned its own request
and grant bits of a single register. For the latter cases, the tg3
driver is incorrectly allowing each function to use the same set of
grant / request bits. This patch fixes the code so that each function
uses the appropriate bitset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed. The idle callback routine could
then schedule a delayed suspend for some time later.
However this behavior was changed by commit
f71648d73c1650b8b4aceb3856bebbde6daa3b86 (PM / Runtime: Remove idle
notification after failing suspend). No notifications were sent, and
there was no clear mechanism to retry failed suspends.
This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down. A companion
patch changes the PM core's behavior, but we also need to change the
USB core. In particular, this patch (as1493) updates the device's
last_busy time when an autosuspend fails, so that the PM core will
retry the autosuspend in the future when the delay time expires
again.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: <stable@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed. The idle callback routine could
then schedule a delayed suspend for some time later.
However this behavior was changed by commit
f71648d73c1650b8b4aceb3856bebbde6daa3b86 (PM / Runtime: Remove idle
notification after failing suspend). No notifications were sent, and
there was no clear mechanism to retry failed suspends.
This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down. Therefore
this patch (as1492) adds a mechanism for retrying failed
autosuspends. If the callback routine updates the last_busy field so
that the next autosuspend expiration time is in the future, the
autosuspend will automatically be rescheduled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: <stable@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
With delta type being int, its value is made zero
for all values of now > 0x80000000.
Hence fixing it.
Signed-off-by: venu byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Another entry for the nonvs blacklist, as noted by a user in
https://bugzilla.redhat.com/show_bug.cgi?id=641789#c12
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Fix panic in RC error flushing logic
IB/iser: DMA unmap TX bufs used for iSCSI/iSER headers
IB/iser: Use separate buffers for the login request/response
IB/mthca: Fix buddy->num_free allocation size
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
|
|
The following panic can occur when flushing a QP:
RIP: 0010:[<ffffffffa0168e8b>] [<ffffffffa0168e8b>] qib_send_complete+0x3b/0x190 [ib_qib]
RSP: 0018:ffff8803cdc6fc90 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff8803d84ba000 RCX: 0000000000000000
RDX: 0000000000000005 RSI: ffffc90015a53430 RDI: ffff8803d84ba000
RBP: ffff8803cdc6fce0 R08: ffff8803cdc6fc90 R09: 0000000000000001
R10: 00000000ffffffff R11: 0000000000000000 R12: ffff8803d84ba0c0
R13: ffff8803d84ba5cc R14: 0000000000000800 R15: 0000000000000246
FS: 0000000000000000(0000) GS:ffff880036600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000034 CR3: 00000003e44f9000 CR4: 00000000000406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process qib/0 (pid: 1350, threadinfo ffff8803cdc6e000, task ffff88042728a100)
Stack:
53544c5553455201 0000000100000005 0000000000000000 ffff8803d84ba000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000000000000000 0000000000000001 ffff8803cdc6fd30 ffffffffa0165d7a
Call Trace:
[<ffffffffa0165d7a>] qib_make_rc_req+0x36a/0xe80 [ib_qib]
[<ffffffffa0165a10>] ? qib_make_rc_req+0x0/0xe80 [ib_qib]
[<ffffffffa01698b3>] qib_do_send+0xf3/0xb60 [ib_qib]
[<ffffffff814db757>] ? thread_return+0x4e/0x777
[<ffffffffa01697c0>] ? qib_do_send+0x0/0xb60 [ib_qib]
[<ffffffff81088bf0>] worker_thread+0x170/0x2a0
[<ffffffff8108e530>] ? autoremove_wake_function+0x0/0x40
[<ffffffff81088a80>] ? worker_thread+0x0/0x2a0
[<ffffffff8108e1c6>] kthread+0x96/0xa0
[<ffffffff8100c1ca>] child_rip+0xa/0x20
[<ffffffff8108e130>] ? kthread+0x0/0xa0
[<ffffffff8100c1c0>] ? child_rip+0x0/0x20
RIP [<ffffffffa0168e8b>] qib_send_complete+0x3b/0x190 [ib_qib]
The RC error state flush logic in qib_make_rc_req() could return all
of the acked wqes and potentially have emptied the queue. It would
then unconditionally try return a flush completion via
qib_send_complete() for an invalid wqe, or worse a valid one that is
not queued. The panic results when the completion code tries to
maintain an MR reference count for a NULL MR.
This fix modifies logic to only send one completion per
qib_make_rc_req() call and changing the completion status from
IB_WC_SUCCESS to IB_WC_WR_FLUSH_ERR as the completions progress.
The outer loop will call as many times as necessary to flush the queue.
Reviewed-by: Ram Vepa <ram.vepa@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The current driver never does DMA unmapping on these buffers. Fix that
by adding DMA unmapping to the task cleanup callback, and DMA mapping to
the task init function (drop the headers_initialized micro-optimization).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The driver counted on the transactional nature of iSCSI login/text
flows and used the same buffer for both the request and the response.
We also went further and did DMA mapping only once, with
DMA_FROM_DEVICE, which violates the DMA mapping API. Fix that by
using different buffers, one for requests and one for responses, and
use the correct DMA mapping direction for each.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Enable IRQ_TYPE_EDGE_BOTH on all R/SH-Mobile ARM SoCs.
This hardware feature is supported by sh7367, sh7377,
sh7372 and sh73a0.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (144 commits)
[media] saa7134.h: Suppress compiler warnings when CONFIG_VIDEO_SAA7134_RC is not set
[media] it913x [VER 1.07] Support for single ITE 9135 devices
[media] Support for Terratec G1
[media] cx25821: off by one in cx25821_vidioc_s_input()
[media] media: tea5764: reconcile Kconfig symbol and macro
[media] omap_vout: Add poll() support
[media] omap3isp: preview: Add crop support on the sink pad
[media] omap3isp: preview: Rename min/max input/output sizes defines
[media] omap3isp: preview: Remove horizontal averager support
[media] omap3isp: Report the ISP revision through the media controller API
[media] omap3isp: ccdc: remove redundant operation
[media] omap3isp: Fix memory leaks in initialization error paths
[media] omap3isp: Add missing mutex_destroy() calls
[media] omap3isp: Move *_init_entities() functions to the init/cleanup section
[media] omap3isp: Move media_entity_cleanup() from unregister() to cleanup()
[media] MFC: Change MFC firmware binary name
[media] vb2: add vb2_get_unmapped_area in vb2 core
[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor
[media] v4l: Add AUTO option for the V4L2_CID_POWER_LINE_FREQUENCY control
[media] media: ov6650: stylistic improvements
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (w83627ehf) Add support for the W83627UHG
hwmon: (w83627ehf) Clean up probe function
hwmon: (w83627ehf) Properly report PECI and AMD-SI sensor types
hwmon: Use i2c_smbus_{read,write}_word_swapped
hwmon: (smsc47b397) Fix checkpatch errors
hwmon: (lm90) Make code more readable
hwmon: (lm90) Fix warnings
hwmon: (ibmaem) Avoid repeated memory allocations
hwmon: (ibmaem) Make instance initializations independent
hwmon: (ibmaem) Fix error paths
hwmon: (lm73) Make detection less problematic
hwmon: Avoid building drivers for powerpc that read/write ISA addresses
|
|
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
dt: add empty of_machine_is_compatible
ahci: add DT binding for Calxeda AHCI controller
dt/platform: minor cleanup
dt: add empty of_alias_get_id() for non-dt builds
|
|
This is essentially a stripped down version of the W83627DHG. Noticeable
difference is that it is still powered with +5V, as older models, even
though the ADC resolution is 8 mV as newer models have.
Thanks to Ulf Bruman (Saab Group) for doing all the testing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The probe function has grown pretty large, I think it's time for some
cleanups, starting with these two simple ones:
* Move temp3/in6 check for the W83667HG later in the function, where
it is done for all other chip types.
* Move temperature register setting to a separate function, to avoid
code duplication.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
