| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver patchset for 3.18-rc1.
Lots of little things in here, some good work from Peter Hurley on the
tty core, and in lots of drivers. There are also lots of other driver
updates in here as well, full details in the changelogs.
All have been in the linux-next tree for a while"
* tag 'tty-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (99 commits)
Revert "serial/core: Initialize the console pm state"
tty: serial: 8250: use 32bit variable for rpm_tx_active
tty: serial: msm: Add earlycon support
serial/core: Initialize the console pm state
serial: asc: Conditionally use readl_relaxed (COMPILE_TEST)
serial: of-serial: add PM suspend/resume support
m68k: AMIGA_BUILTIN_SERIAL should depend on TTY
asm/uapi: Add definition of TIOC[SG]RS485
tty/metag_da: Add console_poll module parameter
serial: 8250_pci: remove rts_n override from Baytrail quirk
serial: cadence: Add generic earlycon support
serial: imx: change the wait even to interruptiable
serial: imx: terminate the RX DMA when the UART is suspending
serial: imx: fix throttle/unthrottle callbacks for hardware assisted flow control
serial: 8250: Add Quark X1000 to 8250_pci.c
tty: omap-serial: pull out calculation from baud_is_mode16
tty: omap-serial: fix division by zero
xen_hvc: no reason to write the type key on xenstore
tty: serial: 8250_core: remove UART_IER_RDI in serial8250_stop_rx()
tty: serial: 8250_core: use the ->line argument as a hint in serial8250_find_match_or_unused()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging updates from Greg KH:
"Here is the big staging patch set for 3.18-rc1.
Once again, we are deleting more code than we added, with something
like 150000 lines deleted overall. Some of this is due to drivers
being added to the networking tree, so the old versions are removed
here, but even then, the overall difference is quite good.
Other than driver deletions, lots and lots and lots of minor cleanups
all over the place. Full details are in the changelog"
* tag 'staging-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1481 commits)
staging: et131x: Remove et131x driver from drivers/staging
staging: emxx_udc: Use min_t instead of min
staging: emxx_udc: Fix replace printk(KERN_DEBUG ..) with dev_dbg
staging: media: Fixed else after return or break warning
staging: media: omap4iss: Fixed else after return or break warning
staging: rtl8712: Fixed else not required after return
staging: rtl8712: Fix missing blank line warning
staging: rtl8192e: rtl8192e: Remove spaces before the semicolons
staging: rtl8192e: rtl8192e: Remove unnecessary return statements
staging: rtl8192e: Remove unneeded void return
staging: rtl8192e: Fix void function return statements style
staging: rtl8712: Fix unnecessary parentheses style warning
staging: rtl8192e: Fix unnecessary space before function pointer arguments
staging: rtl8192e: Array was made static const char * const
staging: ft1000: ft1000-usb: Removed unnecessary else statement.
staging: ft1000: ft1000-usb: Removed unnecessary else statement.
staging: ft1000: ft1000-usb: Removed unnecessary parentheses.
staging: ft1000: ft1000-usb: Added new line after declarations.
staging: vt6655: Fixed C99 // comment errors in wpactl.c
staging: speakup: Fixed warning <linux/serial.h> instead of <asm/serial.h>
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 3.18-rc1. Also in here is the PHY
tree, as it seems to fit well with the USB tree for various reasons...
Anyway, lots of little changes in here, all over the place, full
details in the changelog
All have been in the linux-next tree for a while with no issues"
* tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (244 commits)
USB: host: st: fix typo 'CONFIG_USB_EHCI_HCD_ST'
uas: Reduce number of function arguments for uas_alloc_foo functions
xhci: Allow xHCI drivers to be built as separate modules
xhci: Export symbols used by host-controller drivers
xhci: Check for XHCI_COMP_MODE_QUIRK when disabling D3cold
xhci: Introduce xhci_init_driver()
usb: hcd: add generic PHY support
usb: rename phy to usb_phy in HCD
usb: gadget: uvc: fix up uvcg_v4l2_get_unmapped_area typo
USB: host: st: fix ehci/ohci driver selection
usb: host: ehci-exynos: Remove unnecessary usb-phy support
usb: core: return -ENOTSUPP for all targeted hosts
USB: Remove .owner field for driver
usb: core: log higher level message on malformed LANGID descriptor
usb: Add LED triggers for USB activity
usb: Rename usb-common.c
usb: gadget: Refactor request completion
usb: gadget: Introduce usb_gadget_giveback_request()
usb: dwc2/gadget: move phy bus legth initialization
phy: remove .owner field for drivers using module_platform_driver
...
|
|
Pull crypto update from Herbert Xu:
- add multibuffer infrastructure (single_task_running scheduler helper,
OKed by Peter on lkml.
- add SHA1 multibuffer implementation for AVX2.
- reenable "by8" AVX CTR optimisation after fixing counter overflow.
- add APM X-Gene SoC RNG support.
- SHA256/SHA512 now handles unaligned input correctly.
- set lz4 decompressed length correctly.
- fix algif socket buffer allocation failure for 64K page machines.
- misc fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (47 commits)
crypto: sha - Handle unaligned input data in generic sha256 and sha512.
Revert "crypto: aesni - disable "by8" AVX CTR optimization"
crypto: aesni - remove unused defines in "by8" variant
crypto: aesni - fix counter overflow handling in "by8" variant
hwrng: printk replacement
crypto: qat - Removed unneeded partial state
crypto: qat - Fix typo in name of tasklet_struct
crypto: caam - Dynamic allocation of addresses for various memory blocks in CAAM.
crypto: mcryptd - Fix typos in CRYPTO_MCRYPTD description
crypto: algif - avoid excessive use of socket buffer in skcipher
arm64: dts: add random number generator dts node to APM X-Gene platform.
Documentation: rng: Add X-Gene SoC RNG driver documentation
hwrng: xgene - add support for APM X-Gene SoC RNG support
crypto: mv_cesa - Add missing #define
crypto: testmgr - add test for lz4 and lz4hc
crypto: lz4,lz4hc - fix decompression
crypto: qat - Use pci_enable_msix_exact() instead of pci_enable_msix()
crypto: drbg - fix maximum value checks on 32 bit systems
crypto: drbg - fix sparse warning for cpu_to_be[32|64]
crypto: sha-mb - sha1_mb_alg_state can be static
...
|
|
Pull arch/tile updates from Chris Metcalf:
"The only substantive pieces in this batch are some more vDSO support,
and removing the reference to &platform_bus in tile-srom.c.
The rest are minor issues reported to me"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: add clock_gettime support to vDSO
tile: switch to using seqlocks for the vDSO time code
tile gxio: use better string copy primitive
char: tile-srom: Add real platform bus parent
Removed repeated word in comments
tilegx: Enable ARCH_SUPPORTS_ATOMIC_RMW
tile: Remove tile-specific _sinitdata and _einitdata
tile: use ARRAY_SIZE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- eBPF JIT compiler for arm64
- CPU suspend backend for PSCI (firmware interface) with standard idle
states defined in DT (generic idle driver to be merged via a
different tree)
- Support for CONFIG_DEBUG_SET_MODULE_RONX
- Support for unmapped cpu-release-addr (outside kernel linear mapping)
- set_arch_dma_coherent_ops() implemented and bus notifiers removed
- EFI_STUB improvements when base of DRAM is occupied
- Typos in KGDB macros
- Clean-up to (partially) allow kernel building with LLVM
- Other clean-ups (extern keyword, phys_addr_t usage)
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (51 commits)
arm64: Remove unneeded extern keyword
ARM64: make of_device_ids const
arm64: Use phys_addr_t type for physical address
aarch64: filter $x from kallsyms
arm64: Use DMA_ERROR_CODE to denote failed allocation
arm64: Fix typos in KGDB macros
arm64: insn: Add return statements after BUG_ON()
arm64: debug: don't re-enable debug exceptions on return from el1_dbg
Revert "arm64: dmi: Add SMBIOS/DMI support"
arm64: Implement set_arch_dma_coherent_ops() to replace bus notifiers
of: amba: use of_dma_configure for AMBA devices
arm64: dmi: Add SMBIOS/DMI support
arm64: Correct ftrace calls to aarch64_insn_gen_branch_imm()
arm64:mm: initialize max_mapnr using function set_max_mapnr
setup: Move unmask of async interrupts after possible earlycon setup
arm64: LLVMLinux: Fix inline arm64 assembly for use with clang
arm64: pageattr: Correctly adjust unaligned start addresses
net: bpf: arm64: fix module memory leak when JIT image build fails
arm64: add PSCI CPU_SUSPEND based cpu_suspend support
arm64: kernel: introduce cpu_init_idle CPU operation
...
|
|
Pull KVM updates from Paolo Bonzini:
"Fixes and features for 3.18.
Apart from the usual cleanups, here is the summary of new features:
- s390 moves closer towards host large page support
- PowerPC has improved support for debugging (both inside the guest
and via gdbstub) and support for e6500 processors
- ARM/ARM64 support read-only memory (which is necessary to put
firmware in emulated NOR flash)
- x86 has the usual emulator fixes and nested virtualization
improvements (including improved Windows support on Intel and
Jailhouse hypervisor support on AMD), adaptive PLE which helps
overcommitting of huge guests. Also included are some patches that
make KVM more friendly to memory hot-unplug, and fixes for rare
caching bugs.
Two patches have trivial mm/ parts that were acked by Rik and Andrew.
Note: I will soon switch to a subkey for signing purposes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (157 commits)
kvm: do not handle APIC access page if in-kernel irqchip is not in use
KVM: s390: count vcpu wakeups in stat.halt_wakeup
KVM: s390/facilities: allow TOD-CLOCK steering facility bit
KVM: PPC: BOOK3S: HV: CMA: Reserve cma region only in hypervisor mode
arm/arm64: KVM: Report correct FSC for unsupported fault types
arm/arm64: KVM: Fix VTTBR_BADDR_MASK and pgd alloc
kvm: Fix kvm_get_page_retry_io __gup retval check
arm/arm64: KVM: Fix set_clear_sgi_pend_reg offset
kvm: x86: Unpin and remove kvm_arch->apic_access_page
kvm: vmx: Implement set_apic_access_page_addr
kvm: x86: Add request bit to reload APIC access page address
kvm: Add arch specific mmu notifier for page invalidation
kvm: Rename make_all_cpus_request() to kvm_make_all_cpus_request() and make it non-static
kvm: Fix page ageing bugs
kvm/x86/mmu: Pass gfn and level to rmapp callback.
x86: kvm: use alternatives for VMCALL vs. VMMCALL if kernel text is read-only
kvm: x86: use macros to compute bank MSRs
KVM: x86: Remove debug assertion of non-PAE reserved bits
kvm: don't take vcpu mutex for obviously invalid vcpu ioctls
kvm: Faults which trigger IO release the mmap_sem
...
|
|
Commit 7bced397510a ("net_dma: simple removal") removed the long-dead
net_dma code, but unintentionally broke the build for the qualcomm
crypto engine (qce) that had accidentally depended on the inclusion of
<linux/dmaengine.h> through the networking header files that used to
have it.
Add the required dmaengine.h include explicitly to fix the breakage.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (megaraid_sas,
arcmsr, be2iscsi, lpfc, mpt2sas, mpt3sas, qla2xxx, ufs) plus several
assorted fixes and miscellaneous updates (including the
pci_msix_enable_range() changes that have been pending for a while)"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (202 commits)
scsi: add a CONFIG_SCSI_MQ_DEFAULT option
ufs: definitions for phy interface
ufs: tune bkops while power managment events
ufs: Add support for clock scaling using devfreq framework
ufs: Add freq-table-hz property for UFS device
ufs: Add support for clock gating
ufs: refactor configuring power mode
ufs: add UFS power management support
ufs: introduce well known logical unit in ufs
ufs: manually add well known logical units
ufs: Active Power Mode - configuring bActiveICCLevel
ufs: improve init sequence
ufs: refactor query descriptor API support
ufs: add voting support for host controller power
ufs: Add clock initialization support
ufs: Add regulator enable support
ufs: Allow vendor specific initialization
scsi: don't add scsi_device if its already visible
scsi: fix the type for well known LUs
scsi: fix comment in struct Scsi_Host definition
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A few new haptic/button drivers, a rudimentary support for laptops
using FocalTech touchpads; xpad driver will bind to more devices, and
a few other driver fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: soc_button_array - convert to platform bus
Input: palmas-pwrbutton - fix typo in the license string
Input: palmas-pwrbutton - use IRQF_ONESHOT
Input: psmouse - add support for detecting FocalTech PS/2 touchpads
Input: psmouse - add psmouse_matches_pnp_id helper function
Input: joystick - use ktime for measuring timing
Input: add haptic driver on max77693
Input: introduce palmas-pwrbutton
Input: add support for the DRV2667 haptic driver
Input: xpad - sync device IDs with xboxdrv
Input: xpad - add VID/PID for Razer Sabertooth
Input: cros_ec_keyb - optimize ghosting algorithm
Input: drv260x - fix binding document
Input: drv260x - add check for ERM mode and LRA Libraries
Input: drv260x - remove unused defines
Input: drv260x - add TI drv260x haptics driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- quirk for devices that need to be pulled in much more aggresive way
than mandated, by Johan Hovold
- robustification of sanity checking of incoming reports in RMI driver,
by Benjamin Tissoires
- fixes, updates, and new HW support to SONY driver, by Frank Praznik
- port of uHID to the new transport layer layout, by David Herrmann
- robustification of Clear-Halt/reset in USB HID, by Alan Stern
- native support for hopefully any future HID compliant wacom tablet.
Those found on the various laptops (ISDv4/5) already are HID
compliant and they should work in the future without any modification
of the kernel. Written by Benjamin Tissoires.
- a lot more simple fixes and device ID additions all over the place
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (45 commits)
HID: uHID: fix excepted report type
HID: usbhid: add another mouse that needs QUIRK_ALWAYS_POLL
HID: wacom: implement the finger part of the HID generic handling
HID: wacom: implement generic HID handling for pen generic devices
HID: wacom: move allocation of inputs earlier
HID: wacom: split out input allocation and registration
HID: wacom: rename failN with some meaningful information
HID: sony: Update the DualShock 4 touchpad resolution
HID: wacom: fix timeout on probe for some wacoms
HID: sony: Set touchpad bits in the input_configured callback
HID: sony: Update file header and correct comments
HID: sony: Corrections for the DualShock 4 HID descriptor
HID: rmi: check sanity of the incoming report
HID: wacom: make the WL connection friendly for the desktop
HID: wacom - enable LED support for Wireless Intuos5/Pro
HID: wacom - remove report_id from wacom_get_report interface
HID: wacom - Clean up of sysfs
HID: wacom - Add default permission defines for sysfs attributes
HID: usbhid: fix PIXART optical mouse
HID: Add Holtek USB ID 04d9:a0c2 ETEKCITY Scroll
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull "trivial tree" updates from Jiri Kosina:
"Usual pile from trivial tree everyone is so eagerly waiting for"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
Remove MN10300_PROC_MN2WS0038
mei: fix comments
treewide: Fix typos in Kconfig
kprobes: update jprobe_example.c for do_fork() change
Documentation: change "&" to "and" in Documentation/applying-patches.txt
Documentation: remove obsolete pcmcia-cs from Changes
Documentation: update links in Changes
Documentation: Docbook: Fix generated DocBook/kernel-api.xml
score: Remove GENERIC_HAS_IOMAP
gpio: fix 'CONFIG_GPIO_IRQCHIP' comments
tty: doc: Fix grammar in serial/tty
dma-debug: modify check_for_stack output
treewide: fix errors in printk
genirq: fix reference in devm_request_threaded_irq comment
treewide: fix synchronize_rcu() in comments
checkstack.pl: port to AArch64
doc: queue-sysfs: minor fixes
init/do_mounts: better syntax description
MIPS: fix comment spelling
powerpc/simpleboot: fix comment
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/doc
Pull documentation updates from Jiri Kosina:
"Updates to kernel documentation.
I took this over (hopefully temporarily) from Randy who was not
willing to maintain it any longer. This pile mostly is a relay of
queue that Randy already had in his tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/doc:
Documentation: fix broken v4l-utils URL
Documentation: update include path for mpssd
Documentation: correct parameter error for dma_mapping_error
MAINTAINERS: update location of linux-doc tree
Documentation: remove networking/.gitignore
tools: add more endian.h macros
Make Documenation depend on headers_install
Docs: this_cpu_ops: remove redundant add forms
Documentation: disable vdso_test to avoid breakage with old glibc
Documentation: update vDSO makefile to build portable examples
Documentation: update .gitignore files
Documentation: support glibc versions without htole macros
v4l2-pci-skeleton: Only build if PCI is available
Documentation: fix misc. warnings
Documentation: make functions static to avoid prototype warnings
Documentation: add makefiles for more targets
Documentation: use subdir-y to avoid unnecessary built-in.o files
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A quiet release for SPI, mainly driver updates and not too many of
them:
- Support for dummy transfers (for delays on startup) in drivers
using transfer_one().
- Lots of enhancements to the Designware driver to support new Intel
SoCs.
- Support for newer Renesas chips.
- DMA support for the i.MX driver.
- One new driver for Broadcom BCM53xx chips"
* tag 'spi-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (64 commits)
spi: spi-mxs: fix a tiny typo in a comment
spi: dw-mid: follow new DMAengine workflow
spi: dw-mid: convert to use DMAengine wrappers
spi: dw-mid: change magic numbers to the constants
spi: orion: support armada extended baud rates
spi: fsl: Sort include headers alphabetically
spi: bcm53xx: Add missing module information
spi: bcm53xx: Fix module dependency
spi/rockchip: fix bug that cause the failure to read data in DMA mode
spi: fsl-dspi: Remove probe info message
spi: pl022: Add support for chip select extension
spi: Fix possible ZERO_SIZE_PTR pointer dereferencing error.
spi: dw: fix style of code in few places
spi: dw: introduce support of loopback mode
spi: dw-mid: terminate ongoing transfers at exit
spi: dw-mid: respect 8 bit mode
spi: clps711x: Migrate to the new clk subsystem
spi: pl022: Add missing error check for devm_kzalloc
spi: spi-imx: add DMA support
spi: davinci: add support for adding delay between word's transmissions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This time around most of the changes are a lot of new drivers along
with the standard set of fixes and cleanups (thanks again largely to
Axel Lin). We do have one nice new feature in the core which factors
out the disappointingly tricky code around DT parsing, only a couple
of drivers have been converted so far:
- Factor out the code for parsing the standard bindings for a set of
regulators out of DT, making the probe part of a lot of drivers
simplier.
- New drivers for Dialog DA9213, HiSilicon HI6420, Intersil
ISL9305/H, Ricoh RN5T618, Rockchip RK808, Skyworks SKY81452,
Silergy SYR82x, and Qualcomm RPM"
* tag 'regulator-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (71 commits)
regulator: da9211: Fix a bug in update of mask bit
regulator: pwm-regulator: add devicetree bindings for pwm regulator
regulator: pwm-regulator: get voltage and duty table from dts
regulator: qcom_rpm: Fix FORCE_MODE_IS_2_BITS macro
regulator: qcom_rpm: Don't explicitly initialise the first field of config
regulator: ltc3589: fix broken voltage transitions
regulator: qcom-rpm: Regulator driver for the Qualcomm RPM
regulator: axp20x: Use parent device as regulator configuration device
regulator: fan53555: Fix null pointer dereference
regulator: fan53555: Fixup report wrong vendor message
regulator: fan53555: fix wrong cast in probe
regulator: fan53555: add support for Silergy SYR82x regulators
regulator: fan53555: add devicetree support
regulator: add devicetree bindings for Fairchild FAN53555 regulators
regulator: rk808: Add function for ramp delay for buck1/buck2
regulator: fan53555: use set_ramp_delay to set the ramp up slew rate
regulator: fan53555: enable vin supply
regulator: rk808: Fix missing of_node_put
regulator: rk808: Remove unused variables
regulator: of: Add stub OF match function for !OF case
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"The main update this time around is the addition of a standard DT
binding for specifying the endianness of devices. This allows drivers
to support any endianness of device register map without any code,
useful for configurable IP blocks.
There's also a few bug fixes that I didn't get round to sending, none
of them terribly severe or new, and a reduction in size for struct
regmap"
* tag 'regmap-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix debugfs-file 'registers' mode
regmap: fix possible ZERO_SIZE_PTR pointer dereferencing error.
regmap: debugfs: fix possbile NULL pointer dereference
regmap: fix NULL pointer dereference in _regmap_write/read
regmap: fix NULL pointer dereference in regmap_get_val_endian
regmap: cache: Do not fail silently from regcache_sync calls
regmap: change struct regmap's internal locks as union
regmap: Split regmap_get_endian() in two functions
regmap: of_regmap_get_endian() cleanup
regmap: Fix DT endianess parsing logic
regmap: Add explicit dependencies to catch "select" misuse
regmap: Restore L: linux-kernel@vger.kernel.org entry
regmap: Add the DT binding documentation for endianness
regmap: add DT endianness binding support.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"This is the bulk of pin control changes for the v3.18 development
series:
- New drivers for the Freescale i.MX21, Qualcomm APQ8084 pin
controllers.
- Incremental new features on the Rockchip, atlas 6, OMAP, AM437x,
APQ8064, prima2, AT91, Tegra, i.MX, Berlin and Nomadik.
- Push Freescale drivers down into their own subdirectory.
- Assorted sprays of syntax and semantic fixes"
* tag 'pinctrl-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: specify bindings for pins and groups
pinctrl: nomadik: improve GPIO debug prints
pinctrl: abx500: refactor DT parser to take two paths
pinctrl: abx500: use helpers for map allocation/free
pinctrl: alter device tree bindings for functions
pinctrl: nomadik: refactor DT parser to take two paths
pinctrl: nomadik: use utils map free function
pinctrl: nomadik: use util function to reserve maps
pinctrl: qcom: use restart_notifier mechanism for ps_hold
pinctrl: sh-pfc: sh73a0: Remove unnecessary SoC data allocation
pinctrl: berlin: fix the dt_free_map function
pinctrl: at91: disable PD or PU before enabling PU or PD
pinctrl: st: remove gpiochip in failure cases
pinctrl: at91: Fix error handling while doing gpiochio_irqchip_add
pinctrl: at91: Fix failure path in at91_gpio_probe path
pinctrl: lantiq: Release gpiochip resources in fail case
pinctrl: imx: detect uninitialized pins
pinctrl: tegra: Add MIPI pad control
pinctrl: at91: Switch to using managed clk_get
pinctrl: adi2: Remove duplicate gpiochip_remove_pin_ranges
...
|
|
Pull EDAC fixes from Borislav Petkov:
"Misc small fixes/improvements accumulated from the summer months,
nothing earth-shattering.
The mpc85xx_edac fix is tagged for stable but since it got confirmed
only days before the final 3.17 release, I didn't rush a last minute
pull request to you. I hope that's ok as it will trickle down to
stable anyway and we'll make sure it lands in 3.17-stable too"
* tag 'edac_for_3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
mpc85xx_edac: Make L2 interrupt shared too
amd64_edac: Modify usage of amd64_read_dct_pci_cfg()
ppc4xx_edac: Fix build error caused by wrong member access
EDAC: Fix mem_types strings type
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine updates from Dan Williams:
"Even though this has fixes marked for -stable, given the size and the
needed conflict resolutions this is 3.18-rc1/merge-window material.
These patches have been languishing in my tree for a long while. The
fact that I do not have the time to do proper/prompt maintenance of
this tree is a primary factor in the decision to step down as
dmaengine maintainer. That and the fact that the bulk of drivers/dma/
activity is going through Vinod these days.
The net_dma removal has not been in -next. It has developed simple
conflicts against mainline and net-next (for-3.18).
Continuing thanks to Vinod for staying on top of drivers/dma/.
Summary:
1/ Step down as dmaengine maintainer see commit 08223d80df38
"dmaengine maintainer update"
2/ Removal of net_dma, as it has been marked 'broken' since 3.13
(commit 77873803363c "net_dma: mark broken"), without reports of
performance regression.
3/ Miscellaneous fixes"
* tag 'dmaengine-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
net: make tcp_cleanup_rbuf private
net_dma: revert 'copied_early'
net_dma: simple removal
dmaengine maintainer update
dmatest: prevent memory leakage on error path in thread
ioat: Use time_before_jiffies()
dmaengine: fix xor sources continuation
dma: mv_xor: Rename __mv_xor_slot_cleanup() to mv_xor_slot_cleanup()
dma: mv_xor: Remove all callers of mv_xor_slot_cleanup()
dma: mv_xor: Remove unneeded mv_xor_clean_completed_slots() call
ioat: Use pci_enable_msix_exact() instead of pci_enable_msix()
drivers: dma: Include appropriate header file in dca.c
drivers: dma: Mark functions as static in dma_v3.c
dma: mv_xor: Add DMA API error checks
ioat/dca: Use dev_is_pci() to check whether it is pci device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"Nothing major: support for compressing modules, and auto-tainting
params.
PS. My virtio-next tree is empty: DaveM took the patches I had. There
might be a virtio-rng starvation fix, but so far it's a bit voodoo
so I will get to that in the next two days or it will wait"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
moduleparam: Resolve missing-field-initializer warning
kbuild: handle module compression while running 'make modules_install'.
modinst: wrap long lines in order to enhance cmd_modules_install
modsign: lookup lines ending in .ko in .mod files
modpost: simplify file name generation of *.mod.c files
modpost: reduce visibility of symbols and constify r/o arrays
param: check for tainting before calling set op.
drm/i915: taint the kernel if unsafe module parameters are set
module: add module_param_unsafe and module_param_named_unsafe
module: make it possible to have unsafe, tainting module params
module: rename KERNEL_PARAM_FL_NOARG to avoid confusion
|
|
|
|
This patch fixes a bug on hotmod removing.
After ipmi interface is removed using hotmod, kernel panic occurs when
rmmod impi_si. For example, try this:
# echo "remove,"`cat /proc/ipmi/0/params` > \
/sys/module/ipmi_si/parameters/hotmod
# rmmod ipmi_si
Then, rmmod fails with the following messages.
------------[ cut here ]------------
WARNING: CPU: 12 PID: 10819 at /mnt/repos/linux/lib/list_debug.c:53 __list_del_entry+0x63/0xd0()
CPU: 12 PID: 10819 Comm: rmmod Not tainted 3.17.0-rc1 #19
Hardware name: FUJITSU-SV PRIMERGY BX920 S2/D3030, BIOS 080015 Rev.3D81.3030 02/10/2012
Call Trace:
dump_stack+0x45/0x56
warn_slowpath_common+0x7d/0xa0
warn_slowpath_fmt+0x4c/0x50
__list_del_entry+0x63/0xd0
list_del+0xd/0x30
cleanup_one_si+0x2a/0x230 [ipmi_si]
ipmi_pnp_remove+0x15/0x20 [ipmi_si]
pnp_device_remove+0x24/0x40
__device_release_driver+0x7f/0xf0
driver_detach+0xb0/0xc0
bus_remove_driver+0x55/0xd0
driver_unregister+0x2c/0x50
pnp_unregister_driver+0x12/0x20
cleanup_ipmi_si+0xbc/0xf0 [ipmi_si]
SyS_delete_module+0x132/0x1c0
system_call_fastpath+0x16/0x1b
---[ end trace 70b4377268f85c23 ]---
list_del in cleanup_one_si() fails because the smi_info is already
removed when hotmod removing.
When ipmi interface is removed by hotmod, smi_info is removed by
cleanup_one_si(), but is is still set in drvdata. Therefore when rmmod
ipmi_si, ipmi_pnp_remove tries to remove it again and fails.
By this patch, a pointer to smi_info in drvdata is cleared when hotmod
removing so that it will be not accessed when rmmod.
changelog:
v2:
- Clear drvdata in cleanup_one_si
- Change subject
v1:
https://lkml.org/lkml/2014/9/8/741
Signed-off-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Building ipmi on arm with gcc-4.9 results in this warning for an
allmodconfig build:
drivers/char/ipmi/ipmi_si_intf.c: In function 'ipmi_thread':
include/linux/time.h:28:5: warning: 'busy_until.tv_sec' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (lhs->tv_sec > rhs->tv_sec)
^
drivers/char/ipmi/ipmi_si_intf.c:1007:18: note: 'busy_until.tv_sec' was declared here
struct timespec busy_until;
^
The warning is bogus and this case can not occur. Apparently this is a
false positive resulting from gcc getting a little smarter about
tracking assignments but not smart enough.
Marking the ipmi_thread_busy_wait function as inline gives the gcc
optimization logic enough information to figure out for itself that the
case cannot happen, which gets rid of the warning without adding any
fake initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If an IPMI controller is used by the firmware and as such marked with
a reserved status, we shouldn't use it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The code to send the channel config errors was missing an error report
in one place and needed some more information in another, and had an
extraneous bit of code. Clean all that up.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
'for-3.18/picolcd', 'for-3.18/rmi', 'for-3.18/sony', 'for-3.18/uhid', 'for-3.18/upstream' and 'for-3.18/wacom' into for-linus
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of two small fixes, both to code which went in during
the merge window: cxgb4i has a scheduling in atomic bug in its new
ipv6 code and uas fails to work properly with the new scsi-mq code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] uas: disable use of blk-mq I/O path
[SCSI] cxgb4i: avoid holding mutex in interrupt context
|
|
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Fixes: 905e300e1043 ("USB: host: st: fix ehci/ohci driver selection")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The stream_id and pipe are already present in uas_cmd_info resp uas_dev_info,
so there is no need to pass a copy along.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of building all of the xHCI code into a single module, separate
it out into the core (xhci-hcd), PCI (xhci-pci, now selected by the new
config option CONFIG_USB_XHCI_PCI), and platform (xhci-plat) drivers.
Also update the PCI/platform drivers with module descriptions/licenses
and have them register their respective drivers in their initcalls.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In preparation for allowing the xHCI host controller drivers to be built
as separate modules, export symbols from the xHCI core that may be used
by the host controller drivers.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of calling xhci_compliance_mode_recovery_timer_quirk_check() again
in the PCI suspend path, just check for XHCI_COMP_MODE_QUIRK which will
have been set based on xhci_compliance_mode_recovery_timer_quirk_check()
in xhci_init().
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since the struct hc_driver is mostly the same across the xhci-pci,
xhci-plat, and the upcoming xhci-tegra driver, introduce the function
xhci_init_driver() which will populate the hc_driver with the default
xHCI operations. The caller must supply a setup function which will
be used as the hc_driver's reset callback.
Note that xhci-plat also overrides the default ->start() callback so
that it can do rcar-specific initialization.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Two i2c driver bugfixes"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: qup: Fix order of runtime pm initialization
i2c: rk3x: fix 0 length write transfers
|
|
The current version of the et131x driver has been accepted into the
main tree at /drivers/net/ethernet, so it can now be removed from
staging.
The MAINTAINERS entry has not been touched here, as the patch to
add the driver to drivers/net modifies it correctly.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Prepare first round of input updates for 3.18.
|
|
Pull raid5 discard fix from Neil Brown:
"One fix for raid5 discard issue"
* tag 'md/3.17-final-fix' of git://neil.brown.name/md:
md/raid5: disable 'DISCARD' by default due to safety concerns.
|
|
|
|
'spi/topic/rspi', 'spi/topic/sh-msiof' and 'spi/topic/sirf' into spi-next
|
|
'spi/topic/mxs', 'spi/topic/omap-100k' and 'spi/topic/orion' into spi-next
|
|
'spi/topic/dw' and 'spi/topic/fsl' into spi-next
|
|
'spi/topic/checkpatch' and 'spi/topic/clps711x' into spi-next
|
|
|
|
|
|
|
|
Pull drm fixes from Dave Airlie:
"Nothing too major or scary.
One i915 regression fix, nouveau has a tmds regression fix, along with
a regression fix for the runtime pm code for optimus laptops not
restoring the display hw correctly"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: make sure display hardware is reinitialised on runtime resume
drm/nouveau: punt fbcon resume out to a workqueue
drm/nouveau: fix regression on original nv50 board
drm/nv50/disp: fix dpms regression on certain boards
drm/i915: Flush the PTEs after updating them before suspend
|
|
This replaces http://git.linuxtv.org/v4l-utils/ (broken link)
by http://git.linuxtv.org/cgit.cgi/v4l-utils.git/
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The uas driver uses the block layer tag for USB3 stream IDs. With
blk-mq we can get larger tag numbers that the queue depth, which breaks
this assumption. A fix is under way for 3.18, but sits on top of
large changes so can't easily be backported. Set the disable_blk_mq
path so that a uas device can't easily crash the system when using
blk-mq for SCSI.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This reverts commit a86713b1536c818972675e6dd8c6e738f0379f1d.
Kevin Hilman writes:
Multiple boot failures on ARM[1] were bisected down to this
patch.
How was this patch tested, and on which platforms?
Also, the changelog states that this should be done only for
UART_CAP_SLEEP, but the patch does it for every UART.
Greg, I suggest this patch be dropped from tty-next until it has
been better described and tested.
[1] http://lists.linaro.org/pipermail/kernel-build-reports/2014-October/005550.html
Reported-by: Kevin Hilman <khilman@kernel.org>
Cc: Sudhir Sreedharan <ssreedharan@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
