| Age | Commit message (Collapse) | Author |
|---|
|
DSI contains three separate blocks: protocol engine, PHY and PLL. At the
moment, all these are memory mapped in one big chunk. We need to split
that memory map into smaller pieces so that we can add proper 'reg'
properties into the DT data for each block.
This patch changes the driver to map the blocks separately. It first
tries to get the memory resource using name, used when booting with DT,
and if that fails, it gets the memory resource by ID, in which case the
driver gets the big chunk from platform data. That big chunk is then
split into the smaller blocks manually.
After DSS DT code has been merged and the old platform code removed, we
can clean up the memory resource management.
Instead of changing the driver in all the places where a register is
read or written, this patch takes a shortcut: it adds an additional
number to the struct which represents the register index. This number is
used to decide which base address to use. In the future we should
consider other approaches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
HDMI_IRQ_CORE was not defined in the hdmi.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
HDMI_WP_CLK was wrongly defined as HDMI_WP_WP_CLK. Fix that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
hdmi_wait_for_bit_change() has two issues:
The register index was passed as u16, even if the register index may be
u32. Fix the index to u32.
The function was copied from wait_for_bit_change() which waits for a
single bit to change, but the hdmi version was changed to wait for a bit
field. This change was not done correctly.
The function is supposed to return the (last) value of the bit field,
but it returned !val in case of timeout. This was correct for the single
bit version, but not for the hdmi version. Fix the function to return
the actual value in the register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
DISPC_MSTANDBY_CTRL register is used in the driver, but it's not
restored in dispc_restore_context(), causing problems after resume.
Instead of adding DISPC_MSTANDBY_CTRL to dispc_restore_context(), let's
call _omap_dispc_initial_config() as the first thing in
dispc_runtime_resume(). This will initialize the DISPC core registers
properly, and will avoid similar issues in the future.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
For some reason the hdmi driver first turns off the video output when
it's about to enable the video output. This serves no purpose, and can
be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The hdmi4 driver currently rejects any timing which is not from the CEA or VESA
standards. This leads hdmi rejecting any non-standard mode. A non standard
timing may not have a valid code corresponding to it. In such cases, the HDMI
spec suggests to set the code to 0.
Modify the driver to check if the timings fall within the range of the DISPC
TV overlay manager, and remove the check for an invalid code. Add a debug print
specifying the mode and code in hdmi_display_set_timing.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
DSI has separate TX and RX fifos. However, the current code only has one
field where the fifo size is stored, and the code for both TX and RX
config write to the same field. This has not caused issues, as we've
been using the same fifo sizes.
Fix this bug by creating separate fields for TX and RX fifo sizes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
omapdss in compat mode creates some sysfs files into the device's sysfs
directory, including a 'name' file. This works fine for
platform_devices, but breaks with i2c or spi devices, as those already
have a 'name' file.
Fix this by renaming the omapdss's 'name' file to 'display_name'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
OMAP5 has MFLAG feature in DISPC. Add the register definition and dump
it. The register is not used yet, though.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
When omapfb does ovl->get_overlay_info, ovl->set_overlay_info, the set
function may fail even if the info has not been changed. This is because
omapdss doesn't initialize the info, but expect the caller to set valid
values.
Normally that is the case, but there is at least one corner case: if
omapfb has not allocated memory for the overlay yet, and the user uses
ioctl to disable the overlay to make sure it's disabled. In this case
get_overlay_info returns invalid data, but the user is only interested
in setting the overlay to disabled, not configuring it, and
set_overlay_info fails.
The issue is made possible by the omapfb's setup_plane ioctl, which
groups overlay configuration and overlay enable/disable bit into the
same struct. Thus, when you are disabling an overlay, you are also
configuring it.
This is a bit counter intuitive, so I think it's better to initialize
the info to some valid values.
The fields requiring initialization are color_mode and rotation_type,
and also we need to remove the check for (paddr == 0), as paddr is 0 for
unallocated overlay (but it's still fine to disable the overlay).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Fix debug prints all over omapdss:
* add missing linefeeds
* change pr_err/pr_debug to DSSERR/DSSDBG
* add missing DSS_SUBSYS_NAMEs
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Functions dispc_ovl_set_fifo_threshold and
dispc_ovl_compute_fifo_thresholds need to be exported. Add the
EXPORT_SYMBOLs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"There is a small EFI fix and a big power regression fix in this batch.
My queue also had a fix for downing a CPU when there are insufficient
number of IRQ vectors available, but I'm holding that one for now due
to recent bug reports"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Don't select EFI from certain special ACPI drivers
x86 idle: Repair large-server 50-watt idle-power regression
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes and new device IDs from Rafael Wysocki:
- Fix for a cpufreq regression causing stale sysfs files to be left
behind during system resume if cpufreq_add_dev() fails for one or
more CPUs from Viresh Kumar.
- Fix for a bug in cpufreq causing CONFIG_CPU_FREQ_DEFAULT_* to be
ignored when the intel_pstate driver is used from Jason Baron.
- System suspend fix for a memory leak in pm_vt_switch_unregister()
that forgot to release objects after removing them from
pm_vt_switch_list. From Masami Ichikawa.
- Intel Valley View device ID and energy unit encoding update for the
(recently added) Intel RAPL (Running Average Power Limit) driver from
Jacob Pan.
- Intel Bay Trail SoC GPIO and ACPI device IDs for the Low Power
Subsystem (LPSS) ACPI driver from Paul Drews.
* tag 'pm+acpi-3.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap / RAPL: add support for ValleyView Soc
PM / sleep: Fix memory leak in pm_vt_switch_unregister().
cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
cpufreq: remove sysfs files for CPUs which failed to come back after resume
ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs
|
|
* powercap:
powercap / RAPL: add support for ValleyView Soc
* acpi-lpss:
ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs
|
|
* pm-cpufreq:
cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
cpufreq: remove sysfs files for CPUs which failed to come back after resume
* pm-sleep:
PM / sleep: Fix memory leak in pm_vt_switch_unregister().
|
|
Pull block fixes from Jens Axboe:
- fix for a memory leak on certain unplug events
- a collection of bcache fixes from Kent and Nicolas
- a few null_blk fixes and updates form Matias
- a marking of static of functions in the stec pci-e driver
* 'for-linus' of git://git.kernel.dk/linux-block:
null_blk: support submit_queues on use_per_node_hctx
null_blk: set use_per_node_hctx param to false
null_blk: corrections to documentation
null_blk: warning on ignored submit_queues param
null_blk: refactor init and init errors code paths
null_blk: documentation
null_blk: mem garbage on NUMA systems during init
drivers: block: Mark the functions as static in skd_main.c
bcache: New writeback PD controller
bcache: bugfix for race between moving_gc and bucket_invalidate
bcache: fix for gc and writeback race
bcache: bugfix - moving_gc now moves only correct buckets
bcache: fix for gc crashing when no sectors are used
bcache: Fix heap_peek() macro
bcache: Fix for can_attach_cache()
bcache: Fix dirty_data accounting
bcache: Use uninterruptible sleep in writeback
bcache: kthread don't set writeback task to INTERUPTIBLE
block: fix memory leaks on unplugging block device
bcache: fix sparse non static symbol warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"There's one interseting commit - "libata, freezer: avoid block device
removal while system is frozen". It's an ugly hack working around a
deadlock condition between driver core resume and block layer device
removal paths through freezer which was made more reproducible by
writeback being converted to workqueue some releases ago. The bug has
nothing to do with libata but it's just an workaround which is easy to
backport. After discussion, Rafael and I seem to agree that we don't
really need kernel freezables - both kthread and workqueue. There are
few specific workqueues which constitute PM operations and require
freezing, which will be converted to use workqueue_set_max_active()
instead. All other kernel freezer uses are planned to be removed,
followed by the removal of kthread and workqueue freezer support,
hopefully.
Others are device-specific fixes. The most notable is the addition of
NO_NCQ_TRIM which is used to disable queued TRIM commands to Micro
M500 SSDs which otherwise suffers data corruption"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata, freezer: avoid block device removal while system is frozen
libata: implement ATA_HORKAGE_NO_NCQ_TRIM and apply it to Micro M500 SSDs
libata: disable a disk via libata.force params
ahci: bail out on ICH6 before using AHCI BAR
ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Last batch of InfiniBand/RDMA changes for 3.13 / 2014:
- Additional checks for uverbs to ensure forward compatibility,
handle malformed input better.
- Fix potential use-after-free in iWARP connection manager.
- Make a function static"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/uverbs: Check access to userspace response buffer in extended command
IB/uverbs: Check input length in flow steering uverbs
IB/uverbs: Set error code when fail to consume all flow_spec items
IB/uverbs: Check reserved fields in create_flow
IB/uverbs: Check comp_mask in destroy_flow
IB/uverbs: Check reserved field in extended command header
IB/uverbs: New macro to set pointers to NULL if length is 0 in INIT_UDATA()
IB/core: const'ify inbuf in struct ib_udata
RDMA/iwcm: Don't touch cm_id after deref in rem_ref
RDMA/cxgb4: Make _c4iw_write_mem_dma() static
|
|
Pull drm fixes from Dave Airlie:
"Xmas fixes pull, all small nothing major, intel, radeon, one ttm
regression, and one build fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: Fix swapin regression
gpu: fix qxl missing crc32_le
drm/radeon: fix asic gfx values for scrapper asics
drm/i915: Use the correct GMCH_CTRL register for Sandybridge+
drm/radeon: check for 0 count in speaker allocation and SAD code
drm/radeon/dpm: disable ss on Cayman
drm/radeon/dce6: set correct number of audio pins
drm/i915: get a PC8 reference when enabling the power well
drm/i915: change CRTC assertion on LCPLL disable
drm/i915: Fix erroneous dereference of batch_obj inside reset_status
drm/i915: Prevent double unref following alloc failure during execbuffer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio balloon driver fixes from Rusty Russell:
"Refactoring broke the balloon driver, and fixing kallsyms on ARM broke
some (non-ARM) MMUless setups, so we're making that fix ARM-only for
now.
Unfortunately, the ARM refactoring which broke kallsyms/perf was
CC:stable, so the fix (which broken non-ARM) was also CC:stable, so
now the partial reversion is also CC:stable..."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
scripts/link-vmlinux.sh: only filter kernel symbols for arm
virtio_balloon: update_balloon_size(): update correct field
|
|
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Besides the 2 fixes for tricky corner cases in gem from Chris I've
promised already two patche from Paulo to fix pc8 warnings (both ported
from -next, bug report from Dave Jones) and one patch from to fix vga
enable/disable on snb+. That one is a really old bug, but apparently it
can cause machine hangs if you try hard enough with vgacon/efifb handover.
* tag 'drm-intel-fixes-2013-12-18' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Use the correct GMCH_CTRL register for Sandybridge+
drm/i915: get a PC8 reference when enabling the power well
drm/i915: change CRTC assertion on LCPLL disable
drm/i915: Fix erroneous dereference of batch_obj inside reset_status
drm/i915: Prevent double unref following alloc failure during execbuffer
|
|
into drm-fixes
- fix for a long standing corruption bug on some Trinity/Richland parts.
- Stability fix for cayman dpm
- audio fixes for dce6+
* 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix asic gfx values for scrapper asics
drm/radeon: check for 0 count in speaker allocation and SAD code
drm/radeon/dpm: disable ss on Cayman
drm/radeon/dce6: set correct number of audio pins
|
|
Commit "drm/ttm: Don't move non-existing data" didn't take the
swapped-out corner case into account. This patch corrects that.
Fixes blank screen after attempted suspend / hibernate on vmwgfx.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fix build error: qxl uses crc32 functions so it needs to select
CRC32.
Also use angle quotes around a kernel header file name.
drivers/built-in.o: In function `qxl_display_read_client_monitors_config':
(.text+0x19d754): undefined reference to `crc32_le'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Much smaller batch of fixes this week.
Biggest one is a revert of an OMAP display change that removed some
non-DT pinmux code that was still needed for 3.13 to get DSI displays
to work.
There's also a fix that resolves some misdescribed GPIO controller
resources on shmobile. The rest are mostly smaller fixes, a couple of
MAINTAINERS updates, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
Revert "ARM: OMAP2+: Remove legacy mux code for display.c"
MAINTAINERS: Add keystone clock drivers
MAINTAINERS: Add keystone git tree information
ARM: s3c64xx: dt: Fix boot failure due to double clock initialization
ARM: shmobile: r8a7790: Fix GPIO resources in DTS
irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fixlet from Stefan Richter:
"A one-liner to reenable WRITE SAME over SBP-2 like in v3.8...v3.12.
Buggy targets which could malfunction when being subjected to this
command are already sufficiently protected by a scsi_level check in sd
+ SCSI core"
* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: sbp2: bring back WRITE SAME support
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor items this time around, the most notable being a FILEIO
backend change to enforce hw_max_sectors based upon the current
block_size to address a bug where large sized I/Os (> 1M) where being
rejected"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
target: Remove extra percpu_ref_init
target/file: Update hw_max_sectors based on current block_size
iser-target: Move INIT_WORK setup into isert_create_device_ib_res
iscsi-target: Fix incorrect np->np_thread NULL assignment
qla2xxx: Fix schedule_delayed_work() for target timeout calculations
iser-target: fix error return code in isert_create_device_ib_res()
iscsi-target: Fix-up all zero data-length CDBs with R/W_BIT set
target: Remove write-only stats fields and lock from struct se_node_acl
iscsi-target: return -EINVAL on oversized configfs parameter
|
|
This patch adds support for RAPL on Intel ValleyView based SoC
platforms, such as Baytrail.
Besides adding CPU ID, special energy unit encoding is handled
for ValleyView.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
drivers
When configuring a default governor (via CONFIG_CPU_FREQ_DEFAULT_*) with the
intel_pstate driver, the desired default policy is not properly set. For
example, setting 'CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE' ends up with the
'powersave' policy being set.
Fix by configuring the correct default policy, if either 'powersave' or
'performance' are requested. Otherwise, fallback to what the driver originally
set via its 'init' routine.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There are cases where cpufreq_add_dev() may fail for some CPUs
during system resume. With the current code we will still have
sysfs cpufreq files for those CPUs and struct cpufreq_policy
would be already freed for them. Hence any operation on those
sysfs files would result in kernel warnings.
Example of problems resulting from resume errors (from Bjørn Mork):
WARNING: CPU: 0 PID: 6055 at fs/sysfs/file.c:343 sysfs_open_file+0x77/0x212()
missing sysfs attribute operations for kobject: (null)
Modules linked in: [stripped as irrelevant]
CPU: 0 PID: 6055 Comm: grep Tainted: G D 3.13.0-rc2 #153
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
0000000000000009 ffff8802327ebb78 ffffffff81380b0e 0000000000000006
ffff8802327ebbc8 ffff8802327ebbb8 ffffffff81038635 0000000000000000
ffffffff811823c7 ffff88021a19e688 ffff88021a19e688 ffff8802302f9310
Call Trace:
[<ffffffff81380b0e>] dump_stack+0x55/0x76
[<ffffffff81038635>] warn_slowpath_common+0x7c/0x96
[<ffffffff811823c7>] ? sysfs_open_file+0x77/0x212
[<ffffffff810386e3>] warn_slowpath_fmt+0x41/0x43
[<ffffffff81182dec>] ? sysfs_get_active+0x6b/0x82
[<ffffffff81182382>] ? sysfs_open_file+0x32/0x212
[<ffffffff811823c7>] sysfs_open_file+0x77/0x212
[<ffffffff81182350>] ? sysfs_schedule_callback+0x1ac/0x1ac
[<ffffffff81122562>] do_dentry_open+0x17c/0x257
[<ffffffff8112267e>] finish_open+0x41/0x4f
[<ffffffff81130225>] do_last+0x80c/0x9ba
[<ffffffff8112dbbd>] ? inode_permission+0x40/0x42
[<ffffffff81130606>] path_openat+0x233/0x4a1
[<ffffffff81130b7e>] do_filp_open+0x35/0x85
[<ffffffff8113b787>] ? __alloc_fd+0x172/0x184
[<ffffffff811232ea>] do_sys_open+0x6b/0xfa
[<ffffffff811233a7>] SyS_openat+0xf/0x11
[<ffffffff8138c812>] system_call_fastpath+0x16/0x1b
To fix this, remove those sysfs files or put the associated kobject
in case of such errors. Also, to make it simple, remove the cpufreq
sysfs links from all the CPUs (except for the policy->cpu) during
suspend, as that operation won't result in a loss of sysfs file
permissions and we can create those links during resume just fine.
Fixes: 5302c3fb2e62 ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Reported-and-tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In the case of both the submit_queues param and use_per_node_hctx param
are used. We limit the number af submit_queues to the number of online
nodes.
If the submit_queues is a multiple of nr_online_nodes, its trivial. Simply map
them to the nodes. For example: 8 submit queues are mapped as node0[0,1],
node1[2,3], ...
If uneven, we are left with an uneven number of submit_queues that must be
mapped. These are mapped toward the first node and onward. E.g. 5
submit queues mapped onto 4 nodes are mapped as node0[0,1], node1[2], ...
Signed-off-by: Matias Bjorling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The defaults for the module is to instantiate itself with blk-mq and a
submit queue for each CPU node in the system.
To save resources, initialize instead with a single submit queue.
Signed-off-by: Matias Bjorling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Some pstore backing devices use on board flash as persistent
storage. These have limited numbers of write cycles so it
is a poor idea to use them from high frequency operations.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine fixes from Dan Williams:
- deprecation of net_dma to be removed in 3.14
- crash regression fix in pl330 from the dmaengine_unmap rework
- crash regression fix for any channel running raid ops without
CONFIG_ASYNC_TX_DMA from dmaengine_unmap
- memory leak regression in mv_xor from dmaengine_unmap
- build warning regressions in mv_xor, fsldma, ppc4xx, txx9, and
at_hdmac from dmaengine_unmap
- sleep in atomic regression in dma_async_memcpy_pg_to_pg
- new fix in mv_xor for handling channel initialization failures
* tag 'dmaengine-fixes-3.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
net_dma: mark broken
dma: pl330: ensure DMA descriptors are zero-initialised
dmaengine: fix sleep in atomic
dmaengine: mv_xor: fix oops when channels fail to initialise
dma: mv_xor: Use dmaengine_unmap_data for the self-tests
dmaengine: fix enable for high order unmap pools
dma: fix build warnings in txx9
dmatest: fix build warning on mips
dma: fix fsldma build warnings
dma: fix build warnings in ppc4xx
dmaengine: at_hdmac: remove unused function
dma: mv_xor: remove mv_desc_get_dest_addr()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Renesas ARM based SoC fixes for v3.13
* r8a7790 (R-Car H1) SoC
- Correct GPIO resources in DT.
This problem has been present since GPIOs were added to the r8a7790 SoC
by f98e10c88aa95bf7 ("ARM: shmobile: r8a7790: Add GPIO controller
devices to device tree") in v3.12-rc1.
* irqchip renesas-intc-irqpin
- Correct register bitfield shift calculation
This bug has been present since the renesas-intc-irqpin driver was
introduced by 443580486e3b9657 ("irqchip: Renesas INTC External IRQ pin
driver") in v3.10-rc1
* Lager board
- Do not build the phy fixup unless CONFIG_PHYLIB is enabled
This problem was introduced by 48c8b96f21817aad
* tag 'renesas-fixes-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: Fix GPIO resources in DTS
irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
This patch adds a check on the output buffer with access_ok(VERIFY_WRITE, ...)
to ensure the whole buffer is in userspace memory before using the
pointer in uverbs functions. If the buffer or a subset of it is not
valid, returns -EFAULT to the caller.
This will also catch invalid buffer before the final call to
copy_to_user() which happen late in most uverb functions.
Just like the check in read(2) syscall, it's a sanity check to detect
invalid parameters provided by userspace. This particular check was added
in vfs_read() by Linus Torvalds for v2.6.12 with following commit message:
https://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/commit/?id=fd770e66c9a65b14ce114e171266cf6f393df502
Make read/write always do the full "access_ok()" tests.
The actual user copy will do them too, but only for the
range that ends up being actually copied. That hides
bugs when the range has been clamped by file size or other
issues.
Note: there's no need to check input buffer since vfs_write() already does
access_ok(VERIFY_READ, ...) as part of write() syscall.
Link: http://marc.info/?i=cover.1387273677.git.ydroneaud@opteya.com
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Since ib_copy_from_udata() doesn't check yet the available input data
length before accessing userspace memory, an explicit check of this
length is required to prevent:
- reading past the user provided buffer,
- underflow when subtracting the expected command size from the input
length.
This will ensure the newly added flow steering uverbs don't try to
process truncated commands.
Link: http://marc.info/?i=cover.1386798254.git.ydroneaud@opteya.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
If the flow_spec items parsed count does not match the number of items
declared in the flow_attr command, or if not all bytes are used for
flow_spec items (eg. trailing garbage), a log message is reported and
the function leave through the error path. Unfortunately the error
code is currently not set.
This patch set error code to -EINVAL in such cases, so that the error
is reported to userspace instead of silently fail.
Link: http://marc.info/?i=cover.1386798254.git.ydroneaud@opteya.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
As noted by Daniel Vetter in its article "Botching up ioctls"[1]
"Check *all* unused fields and flags and all the padding for whether
it's 0, and reject the ioctl if that's not the case. Otherwise
your nice plan for future extensions is going right down the
gutters since someone *will* submit an ioctl struct with random
stack garbage in the yet unused parts. Which then bakes in the ABI
that those fields can never be used for anything else but garbage."
It's important to ensure that reserved fields are set to known value,
so that it will be possible to use them latter to extend the ABI.
The same reasonning apply to comp_mask field present in newer uverbs
command: per commit 22878dbc9173 ("IB/core: Better checking of
userspace values for receive flow steering"), unsupported values in
comp_mask are rejected.
[1] http://blog.ffwll.ch/2013/11/botching-up-ioctls.html
Link: http://marc.info/?i=cover.1386798254.git.ydroneaud@opteya.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Just like the check added to create_flow in 22878dbc9173 ("IB/core:
Better checking of userspace values for receive flow steering"),
comp_mask must be checked in destroy_flow too.
Since only empty comp_mask is currently supported, any other value
must be rejected.
This check was silently added in a previous patch[1] to move comp_mask
in extended command header, part of previous patchset[2] against
create/destroy_flow uverbs. The idea of moving comp_mask to the header
was discarded for the final patchset[3].
Unfortunately the check added in destroy_flow uverb was not integrated
in the final patchset.
[1] http://marc.info/?i=40175eda10d670d098204da6aa4c327a0171ae5f.1381510045.git.ydroneaud@opteya.com
[2] http://marc.info/?i=cover.1381510045.git.ydroneaud@opteya.com
[3] http://marc.info/?i=cover.1383773832.git.ydroneaud@opteya.com
Cc: Matan Barak <matanb@mellanox.com>
Link: http://marc.info/?i=cover.1386798254.git.ydroneaud@opteya.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
As noted by Daniel Vetter in its article "Botching up ioctls"[1]
"Check *all* unused fields and flags and all the padding for whether
it's 0, and reject the ioctl if that's not the case. Otherwise
your nice plan for future extensions is going right down the
gutters since someone *will* submit an ioctl struct with random
stack garbage in the yet unused parts. Which then bakes in the ABI
that those fields can never be used for anything else but garbage."
It's important to ensure that reserved fields are set to known value,
so that it will be possible to use them latter to extend the ABI.
The same reasonning apply to comp_mask field present in newer uverbs
command: per commit 22878dbc9173 ("IB/core: Better checking of
userspace values for receive flow steering"), unsupported values in
comp_mask are rejected.
[1] http://blog.ffwll.ch/2013/11/botching-up-ioctls.html
Link: http://marc.info/?i=cover.1386798254.git.ydroneaud@opteya.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Trying to have a ternary operator to choose between NULL (or 0) and the
real pointer value in invocations leads to an impossible choice between
a sparse error about a literal 0 used as a NULL pointer, and a gcc
warning about "pointer/integer type mismatch in conditional expression."
Rather than clutter the source with more casts, move the ternary
operator into a new INIT_UDATA_BUF_OR_NULL() macro, which makes it
easier to use and simplifies its callers.
Reported-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Fix balloon driver for auto-translate guests (PVHVM, ARM) to not use
scratch pages.
- Fix block API header for ARM32 and ARM64 to have proper layout
- On ARM when mapping guests, stick on PTE_SPECIAL
- When using SWIOTLB under ARM, don't call swiotlb functions twice
- When unmapping guests memory and if we fail, don't return pages which
failed to be unmapped.
- Grant driver was using the wrong address on ARM.
* tag 'stable/for-linus-3.13-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: Seperate the auto-translate logic properly (v2)
xen/block: Correctly define structures in public headers on ARM32 and ARM64
arm: xen: foreign mapping PTEs are special.
xen/arm64: do not call the swiotlb functions twice
xen: privcmd: do not return pages which we have failed to unmap
XEN: Grant table address, xen_hvm_resume_frames, is a phys_addr not a pfn
|
|
Fixes gfx corruption on certain TN/RL parts.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=60389
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This patch fixes a possible scsi_host reference leak in qlt_lport_register(),
when a non zero return from the passed (*callback) does not call drop the
local reference via scsi_host_put() before returning.
This currently does not effect existing tcm_qla2xxx code as the passed callback
will never fail, but fix this up regardless for future code.
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
lun->lun_ref is also initialized in core_tpg_post_addlun, so it doesn't
need to be done in core_tpg_setup_virtual_lun0.
(nab: Drop left-over percpu_ref_cancel_init in failure path)
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Commit 7ea6c6c1 ("Move cper.c from drivers/acpi/apei to
drivers/firmware/efi") results in CONFIG_EFI being enabled even
when the user doesn't want this. Since ACPI APEI used to build
fine without UEFI (and as far as I know also has no functional
depency on it), at least in that case using a reverse dependency
is wrong (and a straight one isn't needed).
Whether the same is true for ACPI_EXTLOG I don't know - if there
is a functional dependency, it should depend on EFI rather than
selecting it. It certainly has (currently) no build dependency.
Adjust Kconfig and build logic so that the bad dependency gets
avoided.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/52AF1EBC020000780010DBF9@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
