| Age | Commit message (Collapse) | Author |
|---|
|
This fix alters the ordering of the IRQ and device registrations in the RTC
driver probe function. This change will apply to the RTC driver that supports
both DA9052 and DA9053 PMICs.
A problem could occur with the existing RTC driver if:
A system is started from a cold boot using the PMIC RTC IRQ to initiate a
power on operation. For instance, if an RTC alarm is used to start a
platform from power off.
The existing driver IRQ is requested before the device has been properly
registered.
i.e.
ret = da9052_request_irq()
comes before
rtc->rtc = devm_rtc_device_register();
In this case, an interrupt exists before the device has been registered and
the IRQ handler can be called immediately: this can happen be before the
memory for rtc->rtc has been allocated. The IRQ handler da9052_rtc_irq()
contains the function call:
rtc_update_irq(rtc->rtc, 1, RTC_IRQF | RTC_AF);
which in turn tries to access the unavailable rtc->rtc.
The fix is to reorder the functions inside the RTC probe. The IRQ is
requested after the RTC device resource has been registered so that
da9052_request_irq() is the last thing to happen.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
enabled
If a previously-set alarm was disabled and then triggered, it may still
be pending when a new alarm is configured.
Then, if the alarm is enabled before the pending alarm is cleared, then
an interrupt is immediately raised.
Unfortunately, when the alarm is cleared and enabled during the same I²C
block write, the chip (at least the DS1339 I have) considers that the
alarm is enabled before it is cleared, and raises an interrupt.
This patch ensures that the pending alarm is cleared before the alarm is
enabled.
Signed-off-by: Nicolas Boullis <nboullis@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The i2c_smbus_read_i2c_block_data function returns 0 on success, not the
number of bytes written.
Hence, when there are 32 bytes or less to send, the
ds1307_native_smbus_write_block_data function returns 0 on success,
while it returns the number of bytes when there are more than 32.
The ds1307_write_block_data always returns the number of bytes on
success.
Signed-off-by: Nicolas Boullis <nboullis@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The valid range of day of week register for DS1302 is 1 to 7. But the
set_time callback for rtc-ds1302 attempts to write the value of
tm->tm_wday which is in the range 0 to 6. While the get_time callback
correctly decodes the register.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Sergey Yanovich <ynvich@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The set_time callback for rtc-ds1302 doesn't write clock registers
because the error check for the return value from spi_write_then_read()
is not correct. spi_write_then_read() which returns zero on success.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Sergey Yanovich <ynvich@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Handle the Oscillator Failure (OF) bit on each read of date-time.
If the OF is set, an error is returned (-EINVAL) instead of the date-time.
The OF bit is cleared each time the date is set.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
To enable the wakealarm, the device must be able to wakeup.
This is done by setting the device wakeup capability to true with
'device_init_wakeup' function.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Previous 'commit c3b79770e51a ("Expire alarms after the time is set")'
and 'commit 48e9766726eb ("remove disabled alarm functionality")' removed
the alarm support because the alarm irq was not functional.
Add the alarm IRQ functionality with newer functions than previous
code. Tested with 'rtctest' and the alarm is functional.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Replace the obsolete "simple_strtoul" function to "kstrtoul".
Remove some checkpatch's errors, warnings and checks :
- alignment with open parenthesis
- spaces around '<' and '<<'
- blank line after structure
- quoted string split across lines
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Replace bit shifts by BIT macro.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The driver used i2c_transfer methods to read and set date/time.
The smbus methods should be used.
This commit replaces i2c_transfer functions by i2c_smbus_XX_i2c_block_data
for reading and setting the datetime.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Remove the CONFIG_RTC_INTF_PROC and CONFIG_RTC_INTF_PROC_MODULE macro
which is not necessary anymore.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The driver used an old sysfs entry export.
Update it to use the DEVICE_ATTR_XX macro and remove the unnecessary
CONFIG_RTC_INTF_SYSFS macro.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Many drivers are defining a DRV_VERSION. This is often only used for
MODULE_VERSION and sometimes to print an info message at probe time. This
is kind of pointless as they are all versionned with the kernel anyway.
Also the core will print a message when a new rtc is found.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
mr is written twice with the same value, remove one of the
redundant assignments to mr.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
DS1302 is an half-duplex SPI device. The driver respects this fact now.
Pin configurations should be implemented using SPI subsystem.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Pull networking fixes from David Miller:
1) Fix mvneta/bm dependencies, from Arnd Bergmann.
2) RX completion hw bug workaround in bnxt_en, from Michael Chan.
3) Kernel pointer leak in nf_conntrack, from Linus.
4) Hoplimit route attribute limits not enforced properly, from Paolo
Abeni.
5) qlcnic driver NULL deref fix from Dan Carpenter.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
arm64: bpf: jit JMP_JSET_{X,K}
net/route: enforce hoplimit max value
nf_conntrack: avoid kernel pointer value leak in slab name
drivers: net: xgene: fix register offset
drivers: net: xgene: fix statistics counters race condition
drivers: net: xgene: fix ununiform latency across queues
drivers: net: xgene: fix sharing of irqs
drivers: net: xgene: fix IPv4 forward crash
xen-netback: fix extra_info handling in xenvif_tx_err()
net: mvneta: bm: fix dependencies again
bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)
bnxt_en: Add workaround to detect bad opaque in rx completion (part 1)
qlcnic: potential NULL dereference in qlcnic_83xx_get_minidump_template()
|
|
This patch fixes SG_RX_DV_GATE_REG_0_ADDR register offset
and ring state field lengths.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the race condition on updating the statistics
counters by moving the counters to the ring structure.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses ununiform latency across queues by adding
more queues to match with, upto number of CPU cores.
Also, number of interrupts are increased and the channel numbers
are reordered.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since hardware doesn't allow sharing of interrupts,
this patch fixes the same by removing IRQF_SHARED flag.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the crash observed during IPv4 forward test by
setting the drop field in the dbptr.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A small collection of driver specific fixes for the regulator
subsysetem:
- Fix handling of probe deferral for GPIO regulators
- Fix a typo in the module alias for DA9053
- Fix the definition of BUCK9 in the S2MPS11 driver. This change
looks larger than it is because an irregularity in the hardware
means that the macro used to define bucks 6-10 needs duplicating
and tweaking to have a separate macro for 9
- Fix a series of errors in the definitions of the LDOs the AXP20x
regulators, some of which had always been present and some of which
were introduced in the merge window"
* tag 'regulator-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: da9063: Correct module alias prefix to fix module autoloading
regulator: axp20x: Fix axp22x ldo_io registration error on cold boot
regulator: axp20x: Fix axp22x ldo_io voltage ranges
regulator: axp20x: Fix LDO4 linear voltage range
regulator: s2mps11: Fix invalid selector mask and voltages for buck9
regulator: gpio: check return value of of_get_named_gpio
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"This is rather too late so it'd be completely understandable if you
don't want to pull it at this point, I had thought I'd sent this
earlier but it seems I didn't. Everything has been in -next for some
time now.
The main set of fixes here are mopping up some more issues with MMIO,
fixing handling of endianness configuration in DT (which just wasn't
working at all) and cases where the register and value endianness are
different.
There is also a fix for bulk register reads on SPMI"
* tag 'regmap-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: spmi: Fix regmap_spmi_ext_read in multi-byte case
regmap: mmio: Explicitly say little endian is the defualt in the bus config
regmap: mmio: Parse endianness definitions from DT
regmap: Fix implicit inclusion of device.h
regmap: mmio: Fix value endianness selection
regmap: fix documentation to match code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"A revert fixing a breakage that caused an OOPS on all VB2-based DVB
drivers.
We already have a proper fix, but it sounds safer to keep it being
tested for a while and not hurry, to avoid the risk of another
regression, specially since this is meant to be c/c to stable. So,
for now, let's just revert the broken patch"
* tag 'media/v4.6-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
Revert "[media] videobuf2-v4l2: Verify planes array in buffer dequeueing"
|
|
Pull drm fixes from Dave Airlie:
"A bunch of radeon displayport mode setting fixes, and some misc i915
fixes.
There is one revert, the MST audio code in i915 was causing some
oopses, so we've decided just to drop it until next kernel when we can
fix it properly"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: fix DP mode validation
drm/radeon: fix DP mode validation
drm/i915: Bail out of pipe config compute loop on LPT
drm/radeon: fix PLL sharing on DCE6.1 (v2)
drm/radeon: fix DP link training issue with second 4K monitor
Revert "drm/i915: start adding dp mst audio"
drm/i915/bdw: Add missing delay during L3 SQC credit programming
drm/i915/lvds: separate border enable readout from panel fitter
drm/i915: Update CDCLK_FREQ register on BDW after changing cdclk frequency
|
|
'regulator/fix/da9063', 'regulator/fix/gpio' and 'regulator/fix/s2mps11' into regulator-linus
|
|
'regmap/fix/spmi' into regmap-linus
|
|
|
|
Patch 562abd39 "xen-netback: support multiple extra info fragments
passed from frontend" contained a mistake which can result in an in-
correct number of responses being generated when handling errors
encountered when processing packets containing extra info fragments.
This patch fixes the problem.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reported-by: Jan Beulich <JBeulich@suse.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I tried to fix this before, but my previous fix was incomplete
and we can still get the same link error in randconfig builds
because of the way that Kconfig treats the
default y if MVNETA=y && MVNETA_BM_ENABLE
line that does not actually trigger when MVNETA_BM_ENABLE=m,
unlike I intended.
Changing the line to use MVNETA_BM_ENABLE!=n however has
the desired effect and hopefully makes all configurations
work as expected.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 019ded3aa7c9 ("net: mvneta: bm: clarify dependencies")
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: twl6040-vibra - fix DT node memory management
Input: max8997-haptic - fix NULL pointer dereference
Input: byd - update copyright header
|
|
Switch the order of the loops to walk the rates on the top
so we exhaust all DP 1.1 rate/lane combinations before trying
DP 1.2 rate/lane combos.
This avoids selecting rates that are supported by the monitor,
but not the connector leading to valid modes getting rejected.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=95206
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Switch the order of the loops to walk the rates on the top
so we exhaust all DP 1.1 rate/lane combinations before trying
DP 1.2 rate/lane combos.
This avoids selecting rates that are supported by the monitor,
but not the connector leading to valid modes getting rejected.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=95206
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fix from Linus Walleij:
"A single last pin control fix for v4.6. t's tagged for stable and
only hits a single driver with two added lines so should be safe.
Tested in linux-next.
- The pull up/down logic for the AT91 PIO4 controller was tilted: we
need to mask the reverse pull when unmasking a pull direction.
Setting both pull up & pull down is illegal and makes no sense"
* tag 'pinctrl-v4.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: at91-pio4: fix pull-up/down logic
|
|
Add detection and recovery code when the hardware returned opaque value
does not match the expected consumer index. Once the issue is detected,
we skip the processing of all RX and LRO/GRO packets. These completion
entries are discarded without sending the SKB to the stack and without
producing new buffers. The function will be reset from a workqueue.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a rare hardware bug that can cause a bad opaque value in the RX
or TPA completion. When this happens, the hardware may have used the
same buffer twice for 2 rx packets. In addition, the driver will also
crash later using the bad opaque as the index into the ring.
The rx opaque value is predictable and is always monotonically increasing.
The workaround is to keep track of the expected next opaque value and
compare it with the one returned by hardware during RX and TPA start
completions. If they miscompare, we will not process any more RX and
TPA completions and exit NAPI. We will then schedule a workqueue to
reset the function.
This patch adds the logic to keep track of the next rx consumer index.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If qlcnic_fw_cmd_get_minidump_temp() fails then "fw_dump->tmpl_hdr" is
NULL or possibly freed. It can lead to an oops later.
Fixes: d01a6d3c8ae1 ('qlcnic: Add support to enable capability to extend minidump for iSCSI')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
into drm-fixes
Two some radeon display fixes.
* 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix PLL sharing on DCE6.1 (v2)
drm/radeon: fix DP link training issue with second 4K monitor
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
Misc intel fixes, reverting MST audio which was causing oops for now.
* tag 'drm-intel-fixes-2016-05-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Bail out of pipe config compute loop on LPT
Revert "drm/i915: start adding dp mst audio"
drm/i915/bdw: Add missing delay during L3 SQC credit programming
drm/i915/lvds: separate border enable readout from panel fitter
drm/i915: Update CDCLK_FREQ register on BDW after changing cdclk frequency
|
|
This patch causes a Kernel panic when called on a DVB driver.
This was also reported by David R <david@unsolicited.net>:
May 7 14:47:35 server kernel: [ 501.247123] BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
May 7 14:47:35 server kernel: [ 501.247239] IP: [<ffffffffa0222c71>] __verify_planes_array.isra.3+0x1/0x80 [videobuf2_v4l2]
May 7 14:47:35 server kernel: [ 501.247354] PGD cae6f067 PUD ca99c067 PMD 0
May 7 14:47:35 server kernel: [ 501.247426] Oops: 0000 [#1] SMP
May 7 14:47:35 server kernel: [ 501.247482] Modules linked in: xfs tun xt_connmark xt_TCPMSS xt_tcpmss xt_owner xt_REDIRECT nf_nat_redirect xt_nat ipt_MASQUERADE nf_nat_masquerade_ipv4 ts_kmp ts_bm xt_string ipt_REJECT nf_reject_ipv4 xt_recent xt_conntrack xt_multiport xt_pkttype xt_tcpudp xt_mark nf_log_ipv4 nf_log_common xt_LOG xt_limit iptable_mangle iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_filter ip_tables ip6table_filter ip6_tables x_tables pppoe pppox dm_crypt ts2020 regmap_i2c ds3000 cx88_dvb dvb_pll cx88_vp3054_i2c mt352 videobuf2_dvb cx8800 cx8802 cx88xx pl2303 tveeprom videobuf2_dma_sg ppdev videobuf2_memops videobuf2_v4l2 videobuf2_core dvb_usb_digitv snd_hda_codec_via snd_hda_codec_hdmi snd_hda_codec_generic radeon dvb_usb snd_hda_intel amd64_edac_mod serio_raw snd_hda_codec edac_core fbcon k10temp bitblit softcursor snd_hda_core font snd_pcm_oss i2c_piix4 snd_mixer_oss tileblit drm_kms_helper syscopyarea snd_pcm snd_seq_dummy sysfillrect snd_seq_oss sysimgblt fb_sys_fops ttm snd_seq_midi r8169 snd_rawmidi drm snd_seq_midi_event e1000e snd_seq snd_seq_device snd_timer snd ptp pps_core i2c_algo_bit soundcore parport_pc ohci_pci shpchp tpm_tis tpm nfsd auth_rpcgss oid_registry hwmon_vid exportfs nfs_acl mii nfs bonding lockd grace lp sunrpc parport
May 7 14:47:35 server kernel: [ 501.249564] CPU: 1 PID: 6889 Comm: vb2-cx88[0] Not tainted 4.5.3 #3
May 7 14:47:35 server kernel: [ 501.249644] Hardware name: System manufacturer System Product Name/M4A785TD-V EVO, BIOS 0211 07/08/2009
May 7 14:47:35 server kernel: [ 501.249767] task: ffff8800aebf3600 ti: ffff8801e07a0000 task.ti: ffff8801e07a0000
May 7 14:47:35 server kernel: [ 501.249861] RIP: 0010:[<ffffffffa0222c71>] [<ffffffffa0222c71>] __verify_planes_array.isra.3+0x1/0x80 [videobuf2_v4l2]
May 7 14:47:35 server kernel: [ 501.250002] RSP: 0018:ffff8801e07a3de8 EFLAGS: 00010086
May 7 14:47:35 server kernel: [ 501.250071] RAX: 0000000000000283 RBX: ffff880210dc5000 RCX: 0000000000000283
May 7 14:47:35 server kernel: [ 501.250161] RDX: ffffffffa0222cf0 RSI: 0000000000000000 RDI: ffff880210dc5014
May 7 14:47:35 server kernel: [ 501.250251] RBP: ffff8801e07a3df8 R08: ffff8801e07a0000 R09: 0000000000000000
May 7 14:47:35 server kernel: [ 501.250348] R10: 0000000000000000 R11: 0000000000000001 R12: ffff8800cda2a9d8
May 7 14:47:35 server kernel: [ 501.250438] R13: ffff880210dc51b8 R14: 0000000000000000 R15: ffff8800cda2a828
May 7 14:47:35 server kernel: [ 501.250528] FS: 00007f5b77fff700(0000) GS:ffff88021fc40000(0000) knlGS:00000000adaffb40
May 7 14:47:35 server kernel: [ 501.250631] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
May 7 14:47:35 server kernel: [ 501.250704] CR2: 0000000000000004 CR3: 00000000ca19d000 CR4: 00000000000006e0
May 7 14:47:35 server kernel: [ 501.250794] Stack:
May 7 14:47:35 server kernel: [ 501.250822] ffff8801e07a3df8 ffffffffa0222cfd ffff8801e07a3e70 ffffffffa0236beb
May 7 14:47:35 server kernel: [ 501.250937] 0000000000000283 ffff8801e07a3e94 0000000000000000 0000000000000000
May 7 14:47:35 server kernel: [ 501.251051] ffff8800aebf3600 ffffffff8108d8e0 ffff8801e07a3e38 ffff8801e07a3e38
May 7 14:47:35 server kernel: [ 501.251165] Call Trace:
May 7 14:47:35 server kernel: [ 501.251200] [<ffffffffa0222cfd>] ? __verify_planes_array_core+0xd/0x10 [videobuf2_v4l2]
May 7 14:47:35 server kernel: [ 501.251306] [<ffffffffa0236beb>] vb2_core_dqbuf+0x2eb/0x4c0 [videobuf2_core]
May 7 14:47:35 server kernel: [ 501.251398] [<ffffffff8108d8e0>] ? prepare_to_wait_event+0x100/0x100
May 7 14:47:35 server kernel: [ 501.251482] [<ffffffffa023855b>] vb2_thread+0x1cb/0x220 [videobuf2_core]
May 7 14:47:35 server kernel: [ 501.251569] [<ffffffffa0238390>] ? vb2_core_qbuf+0x230/0x230 [videobuf2_core]
May 7 14:47:35 server kernel: [ 501.251662] [<ffffffffa0238390>] ? vb2_core_qbuf+0x230/0x230 [videobuf2_core]
May 7 14:47:35 server kernel: [ 501.255982] [<ffffffff8106f984>] kthread+0xc4/0xe0
May 7 14:47:35 server kernel: [ 501.260292] [<ffffffff8106f8c0>] ? kthread_park+0x50/0x50
May 7 14:47:35 server kernel: [ 501.264615] [<ffffffff81697a5f>] ret_from_fork+0x3f/0x70
May 7 14:47:35 server kernel: [ 501.268962] [<ffffffff8106f8c0>] ? kthread_park+0x50/0x50
May 7 14:47:35 server kernel: [ 501.273216] Code: 0d 01 74 16 48 8b 46 28 48 8b 56 30 48 89 87 d0 01 00 00 48 89 97 d8 01 00 00 5d c3 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 55 <8b> 46 04 48 89 e5 8d 50 f7 31 c0 83 fa 01 76 02 5d c3 48 83 7e
May 7 14:47:35 server kernel: [ 501.282146] RIP [<ffffffffa0222c71>] __verify_planes_array.isra.3+0x1/0x80 [videobuf2_v4l2]
May 7 14:47:35 server kernel: [ 501.286391] RSP <ffff8801e07a3de8>
May 7 14:47:35 server kernel: [ 501.290619] CR2: 0000000000000004
May 7 14:47:35 server kernel: [ 501.294786] ---[ end trace b2b354153ccad110 ]---
This reverts commit 2c1f6951a8a82e6de0d82b1158b5e493fc6c54ab.
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org
Fixes: 2c1f6951a8a8 ("[media] videobuf2-v4l2: Verify planes array in buffer dequeueing")
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a couple of small fixes: one is a potential uninitialised
error variable in the alua code, potentially causing spurious failures
and the other is a problem caused by the conversion of SCSI to
hostwide tags which resulted in the qla1280 driver always failing in
host initialisation"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
qla1280: Don't allocate 512kb of host tags
scsi_dh_alua: uninitialized variable in alua_rtpg()
|
|
Pull networking fixes from David Miller:
"Hopefully the last round of fixes this release, fingers crossed :)
1) Initialize static nf_conntrack_locks_all_lock properly, from
Florian Westphal.
2) Need to cancel pending work when destroying IDLETIMER entries,
from Liping Zhang.
3) Fix TX param usage when sending TSO over iwlwifi devices, from
Emmanuel Grumbach.
4) NFACCT quota params not validated properly, from Phil Turnbull.
5) Resolve more glibc vs. kernel header conflicts, from Mikko
Tapeli.
6) Missing IRQ free in ravb_close(), from Geert Uytterhoeven.
7) Fix infoleak in x25, from Kangjie Lu.
8) Similarly in thunderx driver, from Heinrich Schuchardt.
9) tc_ife.h uapi header not exported properly, from Jamal Hadi Salim.
10) Don't reenable PHY interreupts if device is in polling mode, from
Shaohui Xie.
11) Packet scheduler actions late binding was not being handled
properly at all, from Jamal Hadi Salim.
12) Fix binding of conntrack entries to helpers in openvswitch, from
Joe Stringer"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
gre: do not keep the GRE header around in collect medata mode
openvswitch: Fix cached ct with helper.
net sched: ife action fix late binding
net sched: skbedit action fix late binding
net sched: simple action fix late binding
net sched: mirred action fix late binding
net sched: ipt action fix late binding
net sched: vlan action fix late binding
net: phylib: fix interrupts re-enablement in phy_start
tcp: refresh skb timestamp at retransmit time
net: nps_enet: bug fix - handle lost tx interrupts
net: nps_enet: Tx handler synchronization
export tc ife uapi header
net: thunderx: avoid exposing kernel stack
net: fix a kernel infoleak in x25 module
ravb: Add missing free_irq() call to ravb_close()
uapi glibc compat: fix compile errors when glibc net/if.h included before linux/if.h
netfilter: nfnetlink_acct: validate NFACCT_QUOTA parameter
iwlwifi: mvm: don't override the rate with the AMSDU len
netfilter: IDLETIMER: fix race condition when destroy the target
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A bunch of small driver specific fixes that have come up, none of them
remarkable in themselves. One fixes a regression introduced in the
merge window and another two are targetted at stable"
* tag 'spi-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: Do not detect number of enabled chip selects on Intel SPT
spi: spi-ti-qspi: Handle truncated frames properly
spi: spi-ti-qspi: Fix FLEN and WLEN settings if bits_per_word is overridden
spi: omap2-mcspi: Undo broken fix for dma transfer of vmalloced buffer
spi: spi-fsl-dspi: Fix cs_change handling in message transfer
|
|
If phy was suspended and is starting, current driver always enable
phy's interrupts, if phy works in polling, phy can raise unexpected
interrupt which will not be handled, the interrupt will block system
enter suspend again. So interrupts should only be re-enabled if phy
works in interrupt.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tx interrupt is of edge type, and in case such interrupt is triggered
while it is masked it will not be handled even after tx interrupts are
re-enabled in the end of NAPI poll.
This will cause tx network to stop in the following scenario:
* Rx is being handled, hence interrupts are masked.
* Tx interrupt is triggered after checking if there is some tx to handle
and before re-enabling the interrupts.
In this situation only rx transaction will release tx requests.
In order to handle the tx that was missed( if there was one ),
a NAPI reschdule was added after enabling the interrupts.
Signed-off-by: Elad Kanfi <eladkan@mellanox.com>
Acked-by: Noam Camus <noamca@mellanox.com>
Acked-by: Gilad Ben-Yossef <giladby@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Below is a description of a possible problematic
sequence. CPU-A is sending a frame and CPU-B handles
the interrupt that indicates the frame was sent. CPU-B
reads an invalid value of tx_packet_sent.
CPU-A CPU-B
----- -----
nps_enet_send_frame
.
.
tx_skb = skb
tx_packet_sent = true
order HW to start tx
.
.
HW complete tx
------> get tx complete interrupt
.
.
if(tx_packet_sent == true)
handle tx_skb
end memory transaction
(tx_packet_sent actually
written)
Furthermore there is a dependency between tx_skb and tx_packet_sent.
There is no assurance that tx_skb contains a valid pointer at CPU B
when it sees tx_packet_sent == true.
Solution:
Initialize tx_skb to NULL and use it to indicate that packet was sent,
in this way tx_packet_sent can be removed.
Add a write memory barrier after setting tx_skb in order to make sure
that it is valid before HW is informed and IRQ is fired.
Fixed sequence will be:
CPU-A CPU-B
----- -----
tx_skb = skb
wmb()
.
.
order HW to start tx
.
.
HW complete tx
------> get tx complete interrupt
.
.
if(tx_skb != NULL)
handle tx_skb
tx_skb = NULL
Signed-off-by: Elad Kanfi <eladkan@mellanox.com>
Acked-by: Noam Camus <noamca@mellanox.com>
Acked-by: Gilad Ben-Yossef <giladby@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Since v4.5, we've WARNed during resume if a PCI device, including a
Thunderbolt device, was added while we were suspended. A change we
merged for v4.6-rc1 turned that warning into a system hang. These
enumeration patches from Lukas Wunner fix this issue:
- Fix BUG on device attach failure
- Do not treat EPROBE_DEFER as device attach failure"
* tag 'pci-v4.6-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Do not treat EPROBE_DEFER as device attach failure
PCI: Fix BUG on device attach failure
|
|
s/paltform/platform/
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
LPT is pch, so might run into the fdi bandwidth constraint (especially
since it has only 2 lanes). But right now we just force pipe_bpp back
to 24, resulting in a nice loop (which we bail out with a loud
WARN_ON). Fix this.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=93477
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462264381-7573-1-git-send-email-daniel.vetter@ffwll.ch
(cherry picked from commit f58a1acc7e4a1f37d26124ce4c875c647fbcc61f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
