| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
Please pull this batch of fixes intended for the 3.10 stream...
Regarding the NFC bits, Samuel says:
"This is the first batch of NFC fixes for 3.10, and it contains:
- 3 fixes for the NFC MEI support:
* We now depend on the correct Kconfig symbol.
* We register an MEI event callback whenever we enable an NFC device,
otherwise we fail to read anything after an enable/disable cycle.
* We only disable an MEI device from its disable mey_phy_ops,
preventing useless consecutive disable calls.
- An NFC Makefile cleanup, as I forgot to remove a commented out line when
moving the LLCP code to the NFC top level directory."
As for the mac80211 bits, Johannes says:
"This time I have a fix from Stanislaw for a stupid mistake I made in the
auth/assoc timeout changes, a fix from Felix for 64-bit traffic counters
and one from Helmut for address mask handling in mac80211. I also have a
few fixes myself for four different crashes reported by a few people."
And Johannes says this about the iwlwifi bit:
"This fixes a brown paper-bag bug that we really should've caught in
review. More details in the changelog for the fix."
On top of that...
Arend van Spriel and Hante Meuleman cooperate to send a series of AP
and P2P mode fixes for brcmfmac.
Gabor Juhos corrects a register offset for AR9550, avoiding a bus
error.
Dan Carpenter provides a fixup to some dmesg output in the atmel
driver.
And, finally...
Felix Fietkau not only gives us a trio of small AR934x fixes, but
also refactors the ath9k aggregation session start/stop handling
(using the generic mac80211 support) in order to avoid a deadlock.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During a PCI EEH/AER error recovery flow, if the device did not successfully
restart, the error_detected() hook may be called a second time with a
"perm_failure" state. This patch skips over driver cleanup for the second
invocation of the callback.
Also, Lancer error recovery code is fixed-up to handle these changes.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW does not compute L4 checksum for IP Fragmented packets.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
We currently allow changing the mq flag (IFF_MULTI_QUEUE) for a persistent
device. This will result a mismatch between the number the queues in netdev and
tuntap. This is because we only allocate a 1q netdevice when IFF_MULTI_QUEUE was
not specified, so when we set the IFF_MULTI_QUEUE and try to attach more queues
later, netif_set_real_num_tx_queues() may fail which result a single queue
netdevice with multiple sockets attached.
Solve this by disallowing changing the mq flag for persistent device.
Bug was introduced by commit edfb6a148ce62e5e19354a1dcd9a34e00815c2a1
(tuntap: reduce memory using of queues).
Reported-by: Sriram Narasimhan <sriram.narasimhan@hp.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Accessing the OTP memory on AR9950 causes a data bus
like this:
Data bus error, epc == 801f7774, ra == 801f7774
Oops[#1]:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.10.0-rc3 #592
task: 87c28000 ti: 87c22000 task.ti: 87c22000
$ 0 : 00000000 00000061 deadc0de 00000000
$ 4 : b8115f18 00015f18 00000007 00000004
$ 8 : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c
$12 : 7c7c3c7c 80320a68 00000000 7c7c7c3c
$16 : 87cd8010 00015f18 00000007 00000000
$20 : 00000064 00000004 87c23c7c 8035210c
$24 : 00000000 801f3674
$28 : 87c22000 87c23b48 00000001 801f7774
Hi : 00000000
Lo : 00000064
epc : 801f7774 ath9k_hw_wait+0x58/0xb0
Not tainted
ra : 801f7774 ath9k_hw_wait+0x58/0xb0
Status: 1000cc03 KERNEL EXL IE
Cause : 4080801c
PrId : 00019750 (MIPS 74Kc)
Modules linked in:
Process swapper (pid: 1, threadinfo=87c22000, task=87c28000, ts=00000000)
Stack : 0000000f 00000061 00002710 8006240c 00000001 87cd8010 87c23bb0 87cd8010
00000000 00000004 00000003 80210c7c 000000b3 67fa8000 0000032a 000006fe
000003e8 00000002 00000028 87c23bf0 000003ff 80210d24 803e5630 80210e28
00000000 00000007 87cd8010 00007044 00000004 00000061 000003ff 000001ff
87c26000 87cd8010 00000220 87cd8bb8 80210000 8020fcf4 87c22000 87c23c08
...
Call Trace:
[<801f7774>] ath9k_hw_wait+0x58/0xb0
[<80210c7c>] ar9300_otp_read_word+0x80/0xd4
[<80210d24>] ar9300_read_otp+0x54/0xb0
[<8020fcf4>] ar9300_check_eeprom_header+0x1c/0x40
[<80210fe4>] ath9k_hw_ar9300_fill_eeprom+0x118/0x39c
[<80206650>] ath9k_hw_eeprom_init+0x74/0xb4
[<801f96d0>] ath9k_hw_init+0x7ec/0x96c
[<801e65ec>] ath9k_init_device+0x340/0x758
[<801f35d0>] ath_ahb_probe+0x21c/0x2c0
[<801c041c>] driver_probe_device+0xc0/0x1e4
[<801c05ac>] __driver_attach+0x6c/0xa4
[<801bea08>] bus_for_each_dev+0x64/0xa8
[<801bfa40>] bus_add_driver+0xcc/0x24c
[<801c0954>] driver_register+0xbc/0x17c
[<803f8fc0>] ath9k_init+0x5c/0x88
[<800608fc>] do_one_initcall+0xec/0x1a0
[<803e6a68>] kernel_init_freeable+0x13c/0x200
[<80309cdc>] kernel_init+0x1c/0xe4
[<80062450>] ret_from_kernel_thread+0x10/0x18
On the AR9550, the OTP registers are located at
the same address as on the AR9340. Use the correct
values to avoid the error.
Cc: stable@vger.kernel.org # 3.6+
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For p2p client mode powersave mode should be kept disabled. It is
working but inefficient. In general p2p links do no benefit from this
mode, because these links are setup temporarily to transfer data.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Multi channel support was disabled. This patch will enable it and
configure the P2P GO on the correct frequency when multi channel
is used.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Upon deleting a P2P_CLIENT/GO interface the vif and consequently
the wdev is freed before the net_device is actually being unregistered
but cfg80211 still needs to access the wdev. Using destructor field
to free the net_device and vif.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When registration fails the net device is no longer needed. Free
the net device and remove reference to private data from the
driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Pass the struct brcmf_cfg80211_info instance instead of obtaining
through vif itself using vif->wdev. This is needed as the netdev
associated with this vif is already unregistered.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The firmware requires that on p2p setup when net interfaces
are created or updated that they start initially with the same
channel as the channel in use for the current connection
(if any). If none exists take default channel 11.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ARP offloading should only be used in STA or P2P client mode. It
is currently configured once at init. When being configured for AP
ARP offloading should be turned off and when AP mode is left it can
be turned back on.
Cc: stable@vger.kernel.org
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
|
|
The phy_init_eee has to exit with an error when the
local device and its link partner both do not support EEE.
So this patch fixes a problem when verify this.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In 63b77bf489881747c5118476918cc8c29378ee63
iwlwifi: dvm: don't send zeroed LQ cmd
I tried to avoid to send zeroed LQ cmd, but I made a (very)
stupid mistake in the memcmp.
Since this patch has been ported to stable, the fix should
go to stable too.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58341
Cc: stable@vger.kernel.org
Reported-by: Hinnerk van Bruinehsen <h.v.bruinehsen@fu-berlin.de>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix to release resources when ptp_clock_register() fail instead
of return error code directly.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the missing free_netdev() before return from function
qlge_probe() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
AR934x v1.3 no longer needs the DCU backoff reduction workaround for
preventing rx overruns, but in turn needs the number of usable Tx
buffers to be reduced slightly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If a local bus timeout has been detected, the host interface needs to be
reset to clear the errors. AR934x uses a different synchronous interrupt
bit to indicate this, so the check needs to be fixed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Do not subtract spur power from noise floor on this chip, as it can lead
to packet loss and other connectivity issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Some more P8 related bits, a bunch of fixes for our P7+/P8 HW crypto
drivers, some added workarounds for those radeons that don't do proper
64-bit MSIs and a couple of other trivialities by myself."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries: Make 32-bit MSI quirk work on systems lacking firmware support
powerpc/powernv: Build a zImage.epapr
powerpc: Make radeon 32-bit MSI quirk work on powernv
powerpc: Context switch more PMU related SPRs
powerpc/powernv: Fix condition for when to invalidate the TCE cache
powerpc/pci: Fix bogus message at boot about empty memory resources
powerpc: Fix TLB cleanup at boot on POWER8
drivers/crypto/nx: Fixes for multiple races and issues
|
|
Pull networking fixes from David Miller:
"It's been a while since my last pull request so quite a few fixes have
piled up."
Indeed.
1) Fix nf_{log,queue} compilation with PROC_FS disabled, from Pablo
Neira Ayuso.
2) Fix data corruption on some tg3 chips with TSO enabled, from Michael
Chan.
3) Fix double insertion of VLAN tags in be2net driver, from Sarveshwar
Bandi.
4) Don't have TCP's MD5 support pass > PAGE_SIZE page offsets in
scatter-gather entries into the crypto layer, the crypto layer can't
handle that. From Eric Dumazet.
5) Fix lockdep splat in 802.1Q MRP code, also from Eric Dumazet.
6) Fix OOPS in netfilter log module when called from conntrack, from
Hans Schillstrom.
7) FEC driver needs to use netif_tx_{lock,unlock}_bh() rather than the
non-BH disabling variants. From Fabio Estevam.
8) TCP GSO can generate out-of-order packets, fix from Eric Dumazet.
9) vxlan driver doesn't update 'used' field of fdb entries when it
should, from Sridhar Samudrala.
10) ipv6 should use kzalloc() to allocate inet6 socket cork options,
otherwise we can OOPS in ip6_cork_release(). From Eric Dumazet.
11) Fix races in bonding set mode, from Nikolay Aleksandrov.
12) Fix checksum generation regression added by "r8169: fix 8168evl
frame padding.", from Francois Romieu.
13) ip_gre can look at stale SKB data pointer, fix from Eric Dumazet.
14) Fix checksum handling when GSO is enabled in bnx2x driver with
certain chips, from Yuval Mintz.
15) Fix double free in batman-adv, from Martin Hundebøll.
16) Fix device startup synchronization with firmware in tg3 driver, from
Nithin Sujit.
17) perf networking dropmonitor doesn't work at all due to mixed up
trace parameter ordering, from Ben Hutchings.
18) Fix proportional rate reduction handling in tcp_ack(), from Nandita
Dukkipati.
19) IPSEC layer doesn't return an error when a valid state is detected,
causing an OOPS. Fix from Timo Teräs.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits)
be2net: bug fix on returning an invalid nic descriptor
tcp: xps: fix reordering issues
net: Revert unused variable changes.
xfrm: properly handle invalid states as an error
virtio_net: enable napi for all possible queues during open
tcp: bug fix in proportional rate reduction.
net: ethernet: sun: drop unused variable
net: ethernet: korina: drop unused variable
net: ethernet: apple: drop unused variable
qmi_wwan: Added support for Cinterion's PLxx WWAN Interface
perf: net_dropmonitor: Remove progress indicator
perf: net_dropmonitor: Use bisection in symbol lookup
perf: net_dropmonitor: Do not assume ordering of dictionaries
perf: net_dropmonitor: Fix symbol-relative addresses
perf: net_dropmonitor: Fix trace parameter order
net: fec: use a more proper compatible string for MVF type device
qlcnic: Fix updating netdev->features
qlcnic: remove netdev->trans_start updates within the driver
qlcnic: Return proper error codes from probe failure paths
tg3: Update version to 3.132
...
|
|
Fixes a race on driver init with registering algorithms where the
driver status flag wasn't being set before self testing started.
Added the cra_alignmask field for CBC and ECB modes.
Fixed a bug in GCM where AES block size was being used instead of
authsize.
Removed use of blkcipher_walk routines for scatterlist processing.
Corner cases in the code prevent us from processing an entire
scatterlist at a time and walking the buffers in block sized chunks
turns out to be unecessary anyway.
Fixed off-by-one error in saving off extra data in the sha code.
Fixed accounting error for number of bytes processed in the sha code.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
In function be_get_nic_desc(), it will go through the descriptor array
returned from f/w. By comparing the desc_type field, it determines whether
there is a nic descriptor in the array or not. In the case of no nic
descriptor, this function should return NULL.
The code may return an invalide descriptor, when there is no nic descriptor
in the array and the desc_count is less than MAX_RESOURCE_DESC. In this case,
even there is no nic descriptor, it will still return the lase descriptor
since the i doesn't equal to MAX_RESOURCE_DESC.
This patch fix this issue by returning the descriptor when find it and return
NULL for other cases.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- An OMAP fix that makes ethernet work again.
- Fix for build problem when building the MCP23S08 driver as module.
- IRQ conflicts in the Langwell driver.
- Fix IRQ coherency issues in the MXS driver.
- Return correct errorcode on errorpath when removing GPIO chips.
* tag 'gpio-fixes-v3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Don't override the error code in probe error handling
gpio: mxs: Use set and clear capabilities of the gpio controller
gpio-langwell: fix irq conflicts when DT is not used
gpio: mcp23s08: Fix build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m
gpio/omap: ensure gpio context is initialised
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Here are some more fixes for v3.10. The Moorestown update broke Intel
Medfield devices, so I reverted it. The acpiphp change fixes a
regression: we broke hotplug notifications to host bridges when we
split acpiphp into the host-bridge related part and the
endpoint-related part.
Moorestown
Revert "x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0"
Hotplug
PCI: acpiphp: Re-enumerate devices when host bridge receives Bus Check"
* tag 'pci-v3.10-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0"
PCI: acpiphp: Re-enumerate devices when host bridge receives Bus Check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A few fixups to Wacom and eGalax touchscreen driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add an eraser to DTH2242/DTK2241
Input: wacom - add a few new styli for Cintiq series
Input: wacom - add three new display tablets
Input: egalax_ts - ABS_MT_POSITION_Y not reported well
|
|
This reverts commits:
c573972c111eb4c6b3f3250ad71e7c75cc799833
1a5904342c7380ceddd61c0b37544d752d0b1433
da2e2c214953f37c2a6be20226537ca5a329724c
They were meant for net-next not net.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg Kroah-Hartman:
"Here are some tty / serial driver fixes for 3.10-rc2.
Nothing huge, although the rocket driver fix looks large, it's just
moving the code around to fix the reported build issues in it. Other
than that, this has the fix for the of-reported lockdep warning from
the vt layer, as well as some other needed bugfixes.
All of these have been in linux-next for a while"
* tag 'tty-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: mxser: Fix build warning introduced by dfc7b837c7f9 (Re: linux-next: build warning after merge of the tty.current tree)
tty: mxser: fix usage of opmode_ioaddr
serial: 8250_dw: add ACPI ID for Intel BayTrail
TTY: Fix tty miss restart after we turn off flow-control
tty/vt: Fix vc_deallocate() lock order
TTY: ehv_bytechan: add missing platform_driver_unregister() when module exit
TTY: rocket, fix more no-PCI warnings
serial: mcf: missing uart_unregister_driver() on error in mcf_init()
tty: serial: mpc5xxx: fix error handing in mpc52xx_uart_init()
serial: samsung: add missing platform_driver_unregister() when module exit
serial: pl011: protect attribute read from NULL platform data struct
tty: nwpserial: Pass correct pointer to free_irq()
serial: 8250_dw: Add valid clk pointer check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg Kroah-Hartman:
"Here are some staging tree driver fixes for 3.10-rc2
The drivers/iio/ changes are here as they are still tied into
drivers/staging/iio/.
Nothing major, just a number of small bugfixes, and a larger
documentation update for the ramster code."
* tag 'staging-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
staging: dwc2: remove compile warning for USB_DWC2_TRACK_MISSED_SOFS
iio: exynos_adc: fix wrong structure extration in suspend and resume
iio:common:st: added disable function after read info raw data
iio: dac: Fix build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m
staging:iio:light:tsl2x7x: fix the error handling in tsl2x7x_probe()
staging/iio/mxs-lradc: fix preenable for multiple buffers
staging: imx-drm: imx-tve: Check the return value of 'regulator_enable()'
staging: video: imx: Select VIDEOMODE_HELPERS for parallel display
staging: ramster: add how-to document
staging: dwc2: Fix dma-enabled platform devices using a default dma_mask
staging: vt6656: [bug] Fix missing spin lock in iwctl_siwpower.
staging: Swap zram and zsmalloc in Kconfig
staging: android: logger: use kuid_t instead of uid_t
staging: zcache: Fix incorrect module_param_array types
staging/solo6x10: depend on CONFIG_FONTS
staging/drm: imx: add missing dependencies
staging: ste_rmi4: Suppress 'ignoring return value of ‘regulator_enable()' warning
staging: sep: fix driver build and kconfig
staging: nvec: cleanup childs on remove
staging: nvec: implement unregistering of notifiers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are 3 tiny driver core fixes for 3.10-rc2.
A needed symbol export, a change to make it easier to track down
offending sysfs files with incorrect attributes, and a klist bugfix.
All have been in linux-next for a while"
* tag 'driver-core-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
klist: del waiter from klist_remove_waiters before wakeup waitting process
driver core: print sysfs attribute name when warning about bogus permissions
driver core: export subsys_virtual_register
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg Kroah-Hartman:
"Here are some small char/misc driver fixes for 3.10-rc2.
Nothing major here, just a number of fixes for things that people have
reported, and a MAINTAINERS update for the recent changes for the
hyperv files that went into 3.10-rc1."
* tag 'char-misc-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
ttyprintk: Fix NULL pointer deref by setting tty_port ops after initializing port
uio: UIO_DMEM_GENIRQ should depend on HAS_DMA
MAINTAINERS: update Hyper-V file list
mei: bus: Reset event_cb when disabling a device
Drivers: hv: Fix a bug in get_vp_index()
mei: fix out of array access to me clients array
Char: lp, protect LPGETSTATUS with port_mutex
dummy-irq: require the user to specify an IRQ number
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of tiny USB bugfixes / new device ids for 3.10-rc2
The majority of these are USB gadget fixes, but they are all small.
Other than that, some USB host controller fixes, and USB serial driver
fixes for problems reported with them.
Also hopefully a fixed up USB_OTG Kconfig dependancy, that one seems
to be almost impossible to get right for all of the different
platforms these days."
* tag 'usb-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (56 commits)
USB: cxacru: potential underflow in cxacru_cm_get_array()
USB: ftdi_sio: Add support for Newport CONEX motor drivers
USB: option: add device IDs for Dell 5804 (Novatel E371) WWAN card
usb: ohci: fix goto wrong tag in err case
usb: isp1760-if: fix memleak when platform_get_resource fail
usb: ehci-s5p: fix memleak when fallback to pdata
USB: serial: clean up chars_in_buffer
USB: ti_usb_3410_5052: fix chars_in_buffer overhead
USB: io_ti: fix chars_in_buffer overhead
USB: ftdi_sio: fix chars_in_buffer overhead
USB: ftdi_sio: clean up get_modem_status
USB: serial: add generic wait_until_sent implementation
USB: serial: add wait_until_sent operation
USB: set device dma_mask without reference to global data
USB: Blacklisted Cinterion's PLxx WWAN Interface
usb: option: Add Telewell TW-LTE 4G
USB: EHCI: remove bogus #error
USB: reset resume quirk needed by a hub
USB: usb-stor: realtek_cr: Fix compile error
usb, chipidea: fix link error when USB_EHCI_HCD is a module
...
|
|
plus send begin and end of express keys events for
Cintiq 13HD and DTH2242/DTK2241
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit 55257d72bd1c51f25106350f4983ec19f62ed1fa (virtio-net: fill only rx
queues which are being used) only does the napi enabling during open for
curr_queue_pairs. This will break multiqueue receiving since napi of new queues
were still disabled after changing the number of queues.
This patch fixes this by enabling napi for all possible queues during open.
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit bfd428d ("net: ethernet: sun: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit e998fd4 ("net: ethernet: korina: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 3b0aaef ("net: ethernet: apple: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull MIPS update from Ralf Baechle:
- Fix a build error if <linux/printk.h> is included without
<linux/linkage.h> having been included before.
- Cleanup and fix the damage done by the generic idle loop patch.
- A kprobes fix that brings the MIPS code in line with what other
architectures are for quite a while already.
- Wire up the native getdents64(2) syscall for 64 bit - for some reason
it was only for the compat ABIs. This has been reported to cause an
application issue. This turned out bigger than I meant but the wait
instruction support code was driving me nuts.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: N64: Wire getdents64(2)
kprobes/mips: Fix to check double free of insn slot
MIPS: Idle: Break r4k_wait into two functions and fix it.
MIPS: Idle: Do address fiddlery in helper functions.
MIPS: Idle: Consolidate all declarations in <asm/idle.h>.
MIPS: Idle: Don't call local_irq_disable() in cpu_wait() implementations.
MIPS: Idle: Re-enable irqs at the end of r3081, au1k and loongson2 cpu_wait.
MIPS: Idle: Make call of function pointer readable.
MIPS: Idle: Consistently reformat inline assembler.
MIPS: Idle: cleaup SMTC idle hook as per Linux coding style.
MIPS: Consolidate idle loop / WAIT instruction support in a single file.
MIPS: clock.h: Remove declaration of cpu_wait.
Add include dependencies to <linux/printk.h>.
MIPS: Rewrite pfn_valid to work in modules, too.
|
|
Remove the compile-time warning for this config option, and instead
warn that it is experimental in the Kconfig text
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added support for Cinterion's PLxx WWAN Interface by adding QMI_FIXED_INTF with
Cinterion's Vendor ID as well as Product ID and WWAN Interface Number.
Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
Signed-off-by: Christian Schmiedl <christian.schmiedl@gemalto.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MVF is a family while MVF600 is a particular SoC in the family. We
generally prefer to use SoC rather than family name in compatible string
to define a particular type of fec device. And this is how fec_dt_ids
works for all those IMX fec variants. Let's change mvf to mvf600 to
have it work in the same way.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o After change in EPORT features of 82xx adapter, netdev->features needs to
be updated to reflect EPORT feature updates but driver was manipulating
netdev->features at wrong place.
o This patch uses netdev_update_features() and .ndo_fix_features() to
update netdev->features properly.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code is removed because netdev->trans_start updates made by the driver
will be ignored by the kernel.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix error paths in probe to assign proper error codes to probe return value.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After resetting the device, the driver waits for a signature to be
updated to know that firmware has completed initialization. However, the
call to tg3_poll_fw() is being done too late and we're writing to the
GRC_MODE register before it has completely initialized, causing
contention with firmware. This logic has existed since day one but is
causing PCIE link to go down randomly at startup on one platform once
every few hundred reboots.
Move the tg3_poll_fw() up to before we write to the GRC_MODE register
after reset.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The exynos_adc device structure was wrongly extracted from the dev*
correcting the same.
Using the regular conversion of
struct device* -> struct platform_device* -> struct exynos_adc* seems wrong.
Instead we should be doing
struct device* -> struct iio_dev* -> struct exynos_adc*
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
