| Age | Commit message (Collapse) | Author |
|---|
|
When chip's temperature is changed, RF characters are changed. To keep the
characters to be consistent, 8723d uses thermal meter to assist in
calibrating LCK, IQK, crystal and TX power.
A base thermal value is programmed in efuse, all calibration data in
MP process is based on this thermal value. So we calucate the delta of
thermal value between the base value, and use this delta to reference XTAL
and TX power offset tables to know how much we need to adjust.
For IQK and LCK, driver checks if delta of thermal value is over 8, then
they are triggered.
For crystal adjustment, when delta of thermal value is changed, we check
XTAL tables to get offset of XTAL value. If thermal value is larger than
base value, positive table (_p as suffix) is used. Otherwise, we use
negative table (_n as suffix). Then, we add offset to XTAL default value
programmed in efuse, and write sum value to register.
To compensate TX power, there are two hierarchical tables. First level use
delta of thermal value to access eight tables to yield delta of TX power
index. Then, plus base TX power index to get index of BB swing table
(second level tables) where register value is induced.
BB swing table can't deal with all cases, if index of BB swing table is
over the size of the table. In this case, TX AGC is used to compensate the
remnant part. Assume 'upper' is the upper bound of BB swing table, and
'target' is the desired index. Then, we can illustrate them as
compensation method BB swing TX AGC
------------------- -------- --------------
target > upper upper target - upper
target < 0 0 target
otherwise target 0
For debug purpose, add a column 'rem' to tx_pwr_tbl entry, and it looks
like
path rate pwr base (byr lmt ) rem
A CCK_1M 32(0x20) 34 -2 ( 0 -2) 0
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-4-yhchuang@realtek.com
|
|
IQ calibration is used to calibrate RF characteristic to yield expected
performance. Basically, we do calibration twice and compare the similarity
to determine calibration is good or not, if not we do the third
calibration, and then compare with the results of first and second
calibration. If it still not similar, IQK is failed.
Before doing calibration, we need to backup registers that will be
modified in calibration procedure, and restore these registers after
calibration is done.
A calibration procedure can divided into four sub-procedures that are
S1-TX, S1-RX, S0-TX and S0-RX. Where, S1 and S0 represent to path A and B
respectively. Each sub-procedure configure proper registers, and then
rigger one-shot calibration and poll until completion. For RX calibration,
it needs to do twice one-shot calibration, first one is to yield parameter
used by second one.
The result of TX part is stored for TX power tracking that adjusts TX AGC
to output expected power.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-3-yhchuang@realtek.com
|
|
LC calibration is done by hardware circuit. Driver sets the LCK bit to kick
start, and then poll the bit to check if it's done.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-2-yhchuang@realtek.com
|
|
An incorrect value of use_fwsup is set for 4-way handshake offload for
WPA//WPA2-PSK, caused by commit 3b1e0a7bdfee ("brcmfmac: add support for
SAE authentication offload"). It results in missing bit
BRCMF_VIF_STATUS_EAP_SUCCESS set in brcmf_is_linkup() and causes the
failure. This patch correct the value for the case.
Also setting bit BRCMF_VIF_STATUS_EAP_SUCCESS for SAE offload case in
brcmf_is_linkup() to fix SAE offload failure.
Fixes: 3b1e0a7bdfee ("brcmfmac: add support for SAE authentication offload")
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1589277788-119966-1-git-send-email-chi-hsien.lin@cypress.com
|
|
Correct name of constant is CLOCK_BOOTTIME and not CLOCK_BOOTIME.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200508195139.20078-1-pali@kernel.org
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507192647.GA16710@embeddedor
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507191926.GA15970@embeddedor
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507190210.GA15375@embeddedor
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507185914.GA15124@embeddedor
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507185529.GA14639@embeddedor
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507185451.GA14603@embeddedor
|
|
caps_buf is always of size sizeof(*caps) because
sizeof(caps->auth_encr_pair) * 16 is always zero. Notice
that when using zero-length arrays, sizeof evaluates to zero[1].
So, the code introduced by
commit 0308383f9591 ("rndis_wlan: get max_num_pmkids from device")
is logically dead, hence is never executed and can be removed. As a
consequence, the rest of the related code can be refactored a bit.
Notice that this code has been out there since March 2010.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200505235205.GA18539@embeddedor
Link: https://lore.kernel.org/r/20200507110741.37757-1-yanaijie@huawei.com
|
|
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1785:5-8:
WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200508074351.19193-1-yanaijie@huawei.com
|
|
Fix sparse warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2206:5:
warning: symbol 'brcmf_p2p_get_conn_idx' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200508013249.95196-1-chenzhou10@huawei.com
|
|
(GTK) keys
When plumbing rxiv for (GTK) keys, current code does not use seq/seq_len
when present nor set iv_initialized for iovar wsec_key. This could
result in missing broadcast traffic after GTK rekey. The fix is setting
iv_initialized and using seq/seq_len for iovar wsec_key.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-4-git-send-email-wright.feng@cypress.com
|
|
The driver sends an action frame down and waits for dwell time to be
completed or aborted before sending out the next action frame.
Driver issues "scan abort" to cancel the current time slot, but this
doesn't have any effect because, we are not using scan engine for
sending action frame.
Fix is to use "actframe_abort" to cancels the current action frame.
Signed-off-by: Ryohei Kondo <ryohei.kondo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-3-git-send-email-wright.feng@cypress.com
|
|
Host driver parses and sets security params into FW passed by
supplicant. This has to be done after reiniting interface in the
firmware.
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-2-git-send-email-wright.feng@cypress.com
|
|
802.1d defines 0,3 for BE and 1,2 for BK. In pcie dongles, 0 & 3 are
mapped to 0 and 1,2 are mapped to 1. This change corrects this mapping,
so that BE & BK are given access precedence accordingly by pcie dongles.
Signed-off-by: Pramod Prakash <pramod.prakash@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588661487-21884-3-git-send-email-chi-hsien.lin@cypress.com
|
|
In WLAN, priority among various access categories of traffic is
always set by the AP using WMM parameters and this may not always
follow the standard 802.1d priority.
In this change, priority is adjusted based on the AP WMM params
received as part of the Assoc Response and the same is later used
to map the priority of all incoming traffic.
In a specific scenario where EDCA parameters are configured to be same
for all ACs, use the default FW priority definition to avoid queuing
packets of all ACs to the same priority queue.
This change fixes the following 802.11 certification tests:
* 11n - 5.2.31 ACM Bit Conformance test
* 11n - 5.2.32 AC Parameter Modification test
* 11ac - 5.2.33 TXOP Limit test
Signed-off-by: Saravanan Shanmugham <saravanan.shanmugham@cypress.com>
Signed-off-by: Justin Li <justin.li@cypress.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588661487-21884-2-git-send-email-chi-hsien.lin@cypress.com
|
|
Currently, bonding always returns NETDEV_TX_OK to its caller.
It is worth trying to be more accurate : TCP for instance
can have different recovery strategies if it can have more
precise status, if packet was dropped by slave qdisc.
This is especially important when host is under stress.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netpoll_send_skb() callers seem to leak skb if
the np pointer is NULL. While this should not happen, we
can make the code more robust.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The unsigned variable val is being checked for an error by checking
if it is less than zero. This can never occur because val is unsigned.
Fix this by making val a plain int.
Addresses-Coverity: ("Unsigned compared against zero")
Fixes: bdbdac7649fa ("ethtool: provide UAPI for PHY master/slave configuration.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NL_SET_ERR_MSG_MOD macro is used to report a string describing an
error message to userspace via the netlink extended ACK structure. It
should not have a trailing newline.
Add a cocci script which catches cases where the newline marker is
present. Using this script, fix the handful of cases which accidentally
included a trailing new line.
I couldn't figure out a way to get a patch mode working, so this script
only implements context, report, and org.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MCU CPSW expected to populate only MDIO device, but follow up patches
will add "compatible" property to the MCU CPSW CPTS node which will cause
creation of CPTS device and MCU CPSW init failure. Hence, switch to use
of_platform_device_create() instead of of_platform_populate() for MDIO
device population.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create an independent function that takes a particular frame queue and
an array of frame descriptors and tries to enqueue them until it hits
the maximum number fo retries. The same function will be used in the
next patch also on the XDP_TX path.
Also, create the dpaa2_eth_xdp_fds structure to incorporate the array of
FDs as well as the number of FDs already populated.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mask the consumer index before using it. Without this, we would be
writing frame descriptors beyond the ring size supported by the QBMAN
block.
Fixes: 3b2abda7d28c ("soc: fsl: dpio: Replace QMAN array mode with ring mode enqueue")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Restrict the TTEthernet hardware support on this switch to operate as
closely as possible to IEEE 802.1Qci as possible. This means that it can
perform PTP-time-based ingress admission control on streams identified
by {DMAC, VID, PCP}, which is useful when trying to ensure the
determinism of traffic scheduled via IEEE 802.1Qbv.
The oddity comes from the fact that in hardware (and in TTEthernet at
large), virtual links always need a full-blown action, including not
only the type of policing, but also the list of destination ports. So in
practice, a single tc-gate action will result in all packets getting
dropped. Additional actions (either "trap" or "redirect") need to be
specified in the same filter rule such that the conforming packets are
actually forwarded somewhere.
Apart from the VL Lookup, Policing and Forwarding tables which need to
be programmed for each flow (virtual link), the Schedule engine also
needs to be told to open/close the admission gates for each individual
virtual link. A fairly accurate (and detailed) description of how that
works is already present in sja1105_tas.c, since it is already used to
trigger the egress gates for the tc-taprio offload (IEEE 802.1Qbv). Key
point here, we remember that the schedule engine supports 8
"subschedules" (execution threads that iterate through the global
schedule in parallel, and that no 2 hardware threads must execute a
schedule entry at the same time). For tc-taprio, each egress port used
one of these 8 subschedules, leaving a total of 4 subschedules unused.
In principle we could have allocated 1 subschedule for the tc-gate
offload of each ingress port, but actually the schedules of all virtual
links installed on each ingress port would have needed to be merged
together, before they could have been programmed to hardware. So
simplify our life and just merge the entire tc-gate configuration, for
all virtual links on all ingress ports, into a single subschedule. Be
sure to check that against the usual hardware scheduling conflicts, and
program it to hardware alongside any tc-taprio subschedule that may be
present.
The following scenarios were tested:
1. Quantitative testing:
tc qdisc add dev swp2 clsact
tc filter add dev swp2 ingress flower skip_sw \
dst_mac 42:be:24:9b:76:20 \
action gate index 1 base-time 0 \
sched-entry OPEN 1200 -1 -1 \
sched-entry CLOSE 1200 -1 -1 \
action trap
ping 192.168.1.2 -f
PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
.............................
--- 192.168.1.2 ping statistics ---
948 packets transmitted, 467 received, 50.7384% packet loss, time 9671ms
2. Qualitative testing (with a phase-aligned schedule - the clocks are
synchronized by ptp4l, not shown here):
Receiver (sja1105):
tc qdisc add dev swp2 clsact
now=$(phc_ctl /dev/ptp1 get | awk '/clock time is/ {print $5}') && \
sec=$(echo $now | awk -F. '{print $1}') && \
base_time="$(((sec + 2) * 1000000000))" && \
echo "base time ${base_time}"
tc filter add dev swp2 ingress flower skip_sw \
dst_mac 42:be:24:9b:76:20 \
action gate base-time ${base_time} \
sched-entry OPEN 60000 -1 -1 \
sched-entry CLOSE 40000 -1 -1 \
action trap
Sender (enetc):
now=$(phc_ctl /dev/ptp0 get | awk '/clock time is/ {print $5}') && \
sec=$(echo $now | awk -F. '{print $1}') && \
base_time="$(((sec + 2) * 1000000000))" && \
echo "base time ${base_time}"
tc qdisc add dev eno0 parent root taprio \
num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time ${base_time} \
sched-entry S 01 50000 \
sched-entry S 00 50000 \
flags 2
ping -A 192.168.1.1
PING 192.168.1.1 (192.168.1.1): 56 data bytes
...
^C
--- 192.168.1.1 ping statistics ---
1425 packets transmitted, 1424 packets received, 0% packet loss
round-trip min/avg/max = 0.322/0.361/0.990 ms
And just for comparison, with the tc-taprio schedule deleted:
ping -A 192.168.1.1
PING 192.168.1.1 (192.168.1.1): 56 data bytes
...
^C
--- 192.168.1.1 ping statistics ---
33 packets transmitted, 19 packets received, 42% packet loss
round-trip min/avg/max = 0.336/0.464/0.597 ms
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement tc-flower offloads for redirect, trap and drop using
non-critical virtual links.
Commands which were tested to work are:
# Send frames received on swp2 with a DA of 42:be:24:9b:76:20 to the
# CPU and to swp3. This type of key (DA only) when the port's VLAN
# awareness state is off.
tc qdisc add dev swp2 clsact
tc filter add dev swp2 ingress flower skip_sw dst_mac 42:be:24:9b:76:20 \
action mirred egress redirect dev swp3 \
action trap
# Drop frames received on swp2 with a DA of 42:be:24:9b:76:20, a VID
# of 100 and a PCP of 0.
tc filter add dev swp2 ingress protocol 802.1Q flower skip_sw \
dst_mac 42:be:24:9b:76:20 vlan_id 100 vlan_prio 0 action drop
Under the hood, all rules match on DMAC, VID and PCP, but when VLAN
filtering is disabled, those are set internally by the driver to the
port-based defaults. Because we would be put in an awkward situation if
the user were to change the VLAN filtering state while there are active
rules (packets would no longer match on the specified keys), we simply
deny changing vlan_filtering unless the list of flows offloaded via
virtual links is empty. Then the user can re-add new rules.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Virtual links are a sja1105 hardware concept of executing various flow
actions based on a key extracted from the frame's DMAC, VID and PCP.
Currently the tc-flower offload code supports only parsing the DMAC if
that is the broadcast MAC address, and the VLAN PCP. Extract the key
parsing logic from the L2 policers functionality and move it into its
own function, after adding extra logic for matching on any DMAC and VID.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the register definitions for the:
- VL Lookup Table
- VL Policing Table
- VL Forwarding Table
- VL Forwarding Parameters Table
These are needed in order to perform TTEthernet operations: QoS
classification, flow-based policing and/or frame redirecting with the
switch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove duplicate headers which are included twice.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The VIA Rhine Ethernet interface is only present on PCI devices or
VIA/WonderMedia VT8500/WM85xx SoCs. Add platform dependencies to the
VIA_RHINE config symbol, to avoid asking the user about it when
configuring a kernel without PCI or VT8500/WM85xx support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'Dan Carpenter' reported:
This code frees "sfi" and then dereferences it on the next line:
> kfree(sfi);
> clear_bit(sfi->index, epsfp.psfp_sfi_bitmap);
This "sfi->index" should be "index".
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function always return 0 now, we can make it return void to
simplify the code. This fixes the following coccicheck warning:
drivers/net/ethernet/microchip/encx24j600.c:609:5-8: Unneeded variable:
"ret". Return "0" on line 653
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following coccicheck warning:
drivers/net/ethernet/mellanox/mlx4/en_ethtool.c:1396:5-8: Unneeded
variable: "err". Return "0" on line 1411
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function always return 0 now, we can make it return void to
simplify the code. This fixes the following coccicheck warning:
drivers/net/ethernet/dec/tulip/de4x5.c:3908:11-17: Unneeded variable:
"status". Return "0" on line 3912
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This code has been marked dead for nearly 10 years. Remove it.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function is dead for more than 10 years. Remove it.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix sparse warnings:
drivers/net/phy/mdio-bcm-iproc.c:182:5: warning:
symbol 'iproc_mdio_resume' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts were all overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix reference count leaks in various parts of batman-adv, from Xiyu
Yang.
2) Update NAT checksum even when it is zero, from Guillaume Nault.
3) sk_psock reference count leak in tls code, also from Xiyu Yang.
4) Sanity check TCA_FQ_CODEL_DROP_BATCH_SIZE netlink attribute in
fq_codel, from Eric Dumazet.
5) Fix panic in choke_reset(), also from Eric Dumazet.
6) Fix VLAN accel handling in bnxt_fix_features(), from Michael Chan.
7) Disallow out of range quantum values in sch_sfq, from Eric Dumazet.
8) Fix crash in x25_disconnect(), from Yue Haibing.
9) Don't pass pointer to local variable back to the caller in
nf_osf_hdr_ctx_init(), from Arnd Bergmann.
10) Wireguard should use the ECN decap helper functions, from Toke
Høiland-Jørgensen.
11) Fix command entry leak in mlx5 driver, from Moshe Shemesh.
12) Fix uninitialized variable access in mptcp's
subflow_syn_recv_sock(), from Paolo Abeni.
13) Fix unnecessary out-of-order ingress frame ordering in macsec, from
Scott Dial.
14) IPv6 needs to use a global serial number for dst validation just
like ipv4, from David Ahern.
15) Fix up PTP_1588_CLOCK deps, from Clay McClure.
16) Missing NLM_F_MULTI flag in gtp driver netlink messages, from
Yoshiyuki Kurauchi.
17) Fix a regression in that dsa user port errors should not be fatal,
from Florian Fainelli.
18) Fix iomap leak in enetc driver, from Dejin Zheng.
19) Fix use after free in lec_arp_clear_vccs(), from Cong Wang.
20) Initialize protocol value earlier in neigh code paths when
generating events, from Roman Mashak.
21) netdev_update_features() must be called with RTNL mutex in macsec
driver, from Antoine Tenart.
22) Validate untrusted GSO packets even more strictly, from Willem de
Bruijn.
23) Wireguard decrypt worker needs a cond_resched(), from Jason
Donenfeld.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
net: flow_offload: skip hw stats check for FLOW_ACTION_HW_STATS_DONT_CARE
MAINTAINERS: put DYNAMIC INTERRUPT MODERATION in proper order
wireguard: send/receive: use explicit unlikely branch instead of implicit coalescing
wireguard: selftests: initalize ipv6 members to NULL to squelch clang warning
wireguard: send/receive: cond_resched() when processing worker ringbuffers
wireguard: socket: remove errant restriction on looping to self
wireguard: selftests: use normal kernel stack size on ppc64
net: ethernet: ti: am65-cpsw-nuss: fix irqs type
ionic: Use debugfs_create_bool() to export bool
net: dsa: Do not leave DSA master with NULL netdev_ops
net: dsa: remove duplicate assignment in dsa_slave_add_cls_matchall_mirred
net: stricter validation of untrusted gso packets
seg6: fix SRH processing to comply with RFC8754
net: mscc: ocelot: ANA_AUTOAGE_AGE_PERIOD holds a value in seconds, not ms
net: dsa: ocelot: the MAC table on Felix is twice as large
net: dsa: sja1105: the PTP_CLK extts input reacts on both edges
selftests: net: tcp_mmap: fix SO_RCVLOWAT setting
net: hsr: fix incorrect type usage for protocol variable
net: macsec: fix rtnl locking issue
net: mvpp2: cls: Prevent buffer overflow in mvpp2_ethtool_cls_rule_del()
...
|
|
This patch adds FLOW_ACTION_HW_STATS_DONT_CARE which tells the driver
that the frontend does not need counters, this hw stats type request
never fails. The FLOW_ACTION_HW_STATS_DISABLED type explicitly requests
the driver to disable the stats, however, if the driver cannot disable
counters, it bails out.
TCA_ACT_HW_STATS_* maintains the 1:1 mapping with FLOW_ACTION_HW_STATS_*
except by disabled which is mapped to FLOW_ACTION_HW_STATS_DISABLED
(this is 0 in tc). Add tc_act_hw_stats() to perform the mapping between
TCA_ACT_HW_STATS_* and FLOW_ACTION_HW_STATS_*.
Fixes: 319a1d19471e ("flow_offload: check for basic action hw stats type")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
coalescing
It's very unlikely that send will become true. It's nearly always false
between 0 and 120 seconds of a session, and in most cases becomes true
only between 120 and 121 seconds before becoming false again. So,
unlikely(send) is clearly the right option here.
What happened before was that we had this complex boolean expression
with multiple likely and unlikely clauses nested. Since this is
evaluated left-to-right anyway, the whole thing got converted to
unlikely. So, we can clean this up to better represent what's going on.
The generated code is the same.
Suggested-by: Sultan Alsawaf <sultan@kerneltoast.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without setting these to NULL, clang complains in certain
configurations that have CONFIG_IPV6=n:
In file included from drivers/net/wireguard/ratelimiter.c:223:
drivers/net/wireguard/selftest/ratelimiter.c:173:34: error: variable 'skb6' is uninitialized when used here [-Werror,-Wuninitialized]
ret = timings_test(skb4, hdr4, skb6, hdr6, &test_count);
^~~~
drivers/net/wireguard/selftest/ratelimiter.c:123:29: note: initialize the variable 'skb6' to silence this warning
struct sk_buff *skb4, *skb6;
^
= NULL
drivers/net/wireguard/selftest/ratelimiter.c:173:40: error: variable 'hdr6' is uninitialized when used here [-Werror,-Wuninitialized]
ret = timings_test(skb4, hdr4, skb6, hdr6, &test_count);
^~~~
drivers/net/wireguard/selftest/ratelimiter.c:125:22: note: initialize the variable 'hdr6' to silence this warning
struct ipv6hdr *hdr6;
^
We silence this warning by setting the variables to NULL as the warning
suggests.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Users with pathological hardware reported CPU stalls on CONFIG_
PREEMPT_VOLUNTARY=y, because the ringbuffers would stay full, meaning
these workers would never terminate. That turned out not to be okay on
systems without forced preemption, which Sultan observed. This commit
adds a cond_resched() to the bottom of each loop iteration, so that
these workers don't hog the core. Note that we don't need this on the
napi poll worker, since that terminates after its budget is expended.
Suggested-by: Sultan Alsawaf <sultan@kerneltoast.com>
Reported-by: Wang Jian <larkwang@gmail.com>
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's already possible to create two different interfaces and loop
packets between them. This has always been possible with tunnels in the
kernel, and isn't specific to wireguard. Therefore, the networking stack
already needs to deal with that. At the very least, the packet winds up
exceeding the MTU and is discarded at that point. So, since this is
already something that happens, there's no need to forbid the not very
exceptional case of routing a packet back to the same interface; this
loop is no different than others, and we shouldn't special case it, but
rather rely on generic handling of loops in general. This also makes it
easier to do interesting things with wireguard such as onion routing.
At the same time, we add a selftest for this, ensuring that both onion
routing works and infinite routing loops do not crash the kernel. We
also add a test case for wireguard interfaces nesting packets and
sending traffic between each other, as well as the loop in this case
too. We make sure to send some throughput-heavy traffic for this use
case, to stress out any possible recursion issues with the locks around
workqueues.
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The K3 INTA driver, which is source TX/RX IRQs for CPSW NUSS, defines IRQs
triggering type as EDGE by default, but triggering type for CPSW NUSS TX/RX
IRQs has to be LEVEL as the EDGE triggering type may cause unnecessary IRQs
triggering and NAPI scheduling for empty queues. It was discovered with
RT-kernel.
Fix it by explicitly specifying CPSW NUSS TX/RX IRQ type as
IRQF_TRIGGER_HIGH.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The addition of sja1105_port_status_ether structure into the
statistics causes the frame size to go over the warning limit:
drivers/net/dsa/sja1105/sja1105_ethtool.c:421:6: error: stack frame size of 1104 bytes in function 'sja1105_get_ethtool_stats' [-Werror,-Wframe-larger-than=]
Use dynamic allocation to avoid this.
Fixes: 336aa67bd027 ("net: dsa: sja1105: show more ethtool statistics counters for P/Q/R/S")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently bool ionic_cq.done_color is exported using
debugfs_create_u8(), which requires a cast, preventing further compiler
checks.
Fix this by switching to debugfs_create_bool(), and dropping the cast.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
