| Age | Commit message (Collapse) | Author |
|---|
|
Linux 4.2-rc4
|
|
For wake from S5, we need to:
- register a reboot handler
- set wakeup capability before requesting IRQ so wakeup count is
incremented
- mask all GPIO IRQs and clear any pending interrupts during driver
probe to since no driver will yet be registered to handle any IRQs
carried over from boot at that time, and it's possible that the
booted kernel does not request the same IRQ anyway.
This means that /sys/.../power/wakeup_count is valid at boot time, and
we can properly account for S5 wakeup stats. e.g.:
### After waking from S5 from a GPIO key
# cat /sys/bus/platform/drivers/brcmstb-gpio/f04172c0.gpio/power/wakeup
enabled
# cat /sys/bus/platform/drivers/brcmstb-gpio/f04172c0.gpio/power/wakeup_count
1
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Uses the gpiolib irqchip helpers. For this to work, the irq setup
function is called once per bank instead of once per device. Note
that all known uses of this block have a BCM7120 L2 interrupt
controller as a parent. Supports interrupts for all GPIOs.
In the IRQ handler, we check for raised IRQs for invalid GPIOs and
warn (ratelimited) if they're encountered.
Also, several drivers (e.g. gpio-keys) allow for GPIOs to be
configured as wakeup sources, and this GPIO controller supports that
through a separate interrupt path.
The de-facto standard DT property "wakeup-source" is checked, since
that indicates whether the GPIO controller hardware can wake. Uses
the IRQCHIP_MASK_ON_SUSPEND irq_chip flag because UPG GIO doesn't have
any of its own wakeup source configuration.
Aside regarding gpiolib irqchip helpers: It wasn't obvious (to me)
that you can have multiple chained irqchips and associated IRQ domains
for a single parent IRQ, and as long as the xlate function is written
correctly, a GPIO IRQ request end up checking the correct domain and
will get associated with the correct IRQ. What helps make this clear
is to read
drivers/gpio/gpiolib-of.c:
- of_gpiochip_find_and_xlate()
- of_get_named_gpiod_flags()
drivers/gpio/gpiolib.c:
- gpiochip_find()
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On ETRAX FS, all pins on the first port (and only the first port) have
interrupt support.
On ARTPEC-3, all pins on all ports have interrupt support. However,
there are only eight interrupts. Each of the interrupts is associated
with a group of pins and for each interrupt the one pin from the group
which will trigger it can be selected.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If the driver has specified its own irq_{request/release}_resources()
functions, don't override them. The gpio-etraxfs driver will use this.
Signed-off-by: Rabin Vincent <rabin@rab.in>
[Added a small comment blurb]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
mpc8xxx_gpio_chip.lock needs to be a real spinlock in preempt-rt.
Especially the interrupt related functions can not be converted to a
sleeping lock.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER if
the pin controller isn't available.
Otherwise, the GPIO range wouldn't be set at all unless the pin
controller probed always before the GPIO chip.
With this change, the probe of the GPIO chip will be deferred and will
be retried at a later point, hopefully once the pin controller has been
registered and probed already.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed as most platforms don't use probing.
There appears to be a great deal of blind copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add support for the GIO block in the ARTPEC-3 SoC. The basic
functionality is essentialy the same as the version in the ETRAX FS,
except for a different set of ports, including a read-only port.
Cc: devicetree@vger.kernel.org
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Allow chips to indicates that they are input-only and thus cannot set
the output value. This will be used by the gpio-etraxfs driver.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
BGPIO_F_UNREADABLE_REG_SET is incorrect, since the set register _is_
readable. What's really required is BGPIO_F_READ_OUTPUT_REG_SET:
reading the set register reads the set output value.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
R-Car Gen3's GPIO blocks are identical to Gen2's in every respect.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch converts gpio_bank.lock from a spin_lock into a
raw_spin_lock. The call path is to access this lock is always under a
raw_spin_lock, for instance
- __setup_irq() holds &desc->lock with irq off
+ __irq_set_trigger()
+ omap_gpio_irq_type()
- handle_level_irq() (runs with irqs off therefore raw locks)
+ mask_ack_irq()
+ omap_gpio_mask_irq()
This fixes the obvious backtrace on -RT. However the locking vs context
is not and this is not limited to -RT:
- omap_gpio_irq_type() is called with IRQ off and has an conditional
call to pm_runtime_get_sync() which may sleep. Either it may happen or
it may not happen but pm_runtime_get_sync() should not be called with
irqs off.
- omap_gpio_debounce() is holding the lock with IRQs off.
+ omap2_set_gpio_debounce()
+ clk_prepare_enable()
+ clk_prepare() this one might sleep.
The number of users of gpiod_set_debounce() / gpio_set_debounce()
looks low but still this is not good.
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This variable is used as an iterator and initialized in the
list_for_each() loop.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The gpio controller on MPC5125 is identical to the MPC5121 register
wise, the only difference is that the lines 0..3 are input only instead
of 28..31 on MPC5121.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The gpio controllers that are handled by the mpc8xxx driver differ
slightly. Up to now some differences were handled by use of
of_device_is_compatible, others by use of struct of_device_id's data.
To make this consistent and easily extendable handle the differences at
a single place.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This variable is not modified in the driver and all functions it it
passed to don't change it either. So it can and should be marked const.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"This update contains:
- the manual revert of the SYSCALL32 changes which caused a
regression
- a fix for the MPX vma handling
- three fixes for the ioremap 'is ram' checks.
- PAT warning fixes
- a trivial fix for the size calculation of TLB tracepoints
- handle old EFI structures gracefully
This also contains a PAT fix from Jan plus a revert thereof. Toshi
explained why the code is correct"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/pat: Revert 'Adjust default caching mode translation tables'
x86/asm/entry/32: Revert 'Do not use R9 in SYSCALL32' commit
x86/mm: Fix newly introduced printk format warnings
mm: Fix bugs in region_is_ram()
x86/mm: Remove region_is_ram() call from ioremap
x86/mm: Move warning from __ioremap_check_ram() to the call site
x86/mm/pat, drivers/media/ivtv: Move the PAT warning and replace WARN() with pr_warn()
x86/mm/pat, drivers/infiniband/ipath: Replace WARN() with pr_warn()
x86/mm/pat: Adjust default caching mode translation tables
x86/fpu: Disable dependent CPU features on "noxsave"
x86/mpx: Do not set ->vm_ops on MPX VMAs
x86/mm: Add parenthesis for TLB tracepoint size calculation
efi: Handle memory error structures produced based on old versions of standard
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here's a few USB and PHY fixes for 4.2-rc4.
Nothing major, the shortlog has the full details.
All of these have been in linux-next successfully"
* tag 'usb-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
USB: OHCI: fix bad #define in ohci-tmio.c
cdc-acm: Destroy acm_minors IDR on module exit
usb-storage: Add ignore-device quirk for gm12u320 based usb mini projectors
usb-storage: ignore ZTE MF 823 card reader in mode 0x1225
USB: OHCI: Fix race between ED unlink and URB submission
usb: core: lpm: set lpm_capable for root hub device
xhci: do not report PLC when link is in internal resume state
xhci: prevent bus_suspend if SS port resuming in phase 1
xhci: report U3 when link is in resume state
xhci: Calculate old endpoints correctly on device reset
usb: xhci: Bugfix for NULL pointer deference in xhci_endpoint_init() function
xhci: Workaround to get D3 working in Intel xHCI
xhci: call BIOS workaround to enable runtime suspend on Intel Braswell
usb: dwc3: Reset the transfer resource index on SET_INTERFACE
usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU
usb: gadget: mv_udc_core: fix phy_regs I/O memory leak
usb: ulpi: ulpi_init should be executed in subsys_initcall
phy: berlin-usb: fix divider for BG2
phy: berlin-usb: fix divider for BG2CD
phy/pxa: add HAS_IOMEM dependency
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small serial and tty fixes for reported issues.
All have been in linux-next successfully"
* tag 'tty-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: vt: Fix !TASK_RUNNING diagnostic warning from paste_selection()
serial: core: Fix crashes while echoing when closing
m32r: Add ioreadXX/iowriteXX big-endian mmio accessors
Revert "serial: imx: initialized DMA w/o HW flow enabled"
sc16is7xx: fix FIFO address of secondary UART
sc16is7xx: fix Kconfig dependencies
serial: etraxfs-uart: Fix release etraxfs_uart_ports
tty/vt: Fix the memory leak in visual_init
serial: amba-pl011: Fix devm_ioremap_resource return value check
n_tty: signal and flush atomically
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a number of iio and staging driver fixes for reported issues
for 4.2-rc4.
All have been in linux-next for a while with no problems"
* tag 'staging-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (34 commits)
iio:light:stk3310: make endianness independent of host
iio:light:stk3310: move device register to end of probe
iio: mma8452: use iio event type IIO_EV_TYPE_MAG
iio: mcp320x: Fix NULL pointer dereference
iio: adc: vf610: fix the adc register read fail issue
iio: mlx96014: Replace offset sign
iio: magnetometer: mmc35240: fix SET/RESET sequence
iio: magnetometer: mmc35240: Fix SET/RESET mask
iio: magnetometer: mmc35240: Fix crash in pm suspend
iio:magnetometer:bmc150_magn: output intended variable
iio:magnetometer:bmc150_magn: add regmap dependency
staging: vt6656: check ieee80211_bss_conf bssid not NULL
staging: vt6655: check ieee80211_bss_conf bssid not NULL
iio: tmp006: Check channel info on write
iio: sx9500: Add missing init in sx9500_buffer_pre{en,dis}able()
iio:light:ltr501: fix regmap dependency
iio:light:ltr501: fix variable in ltr501_init
iio: sx9500: fix bug in compensation code
iio: sx9500: rework error handling of raw readings
iio: magnetometer: mmc35240: fix available sampling frequencies
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some char and misc driver fixes for reported issues.
One parport patch is reverted as it was incorrect, thanks to testing
by the 0-day bot"
* tag 'char-misc-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
parport: Revert "parport: fix memory leak"
mei: prevent unloading mei hw modules while the device is opened.
misc: mic: scif bug fix for vmalloc_to_page crash
parport: fix freeing freed memory
parport: fix memory leak
parport: fix error handling
|
|
This reverts commit 23c405912b88 ("parport: fix memory leak")
par_dev->state was already being removed in parport_unregister_device().
Reported-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm
Pull libnvdimm fix from Dan Williams:
"A minor fix for the libnvdimm subsystem.
This is not critical. The problem can be worked around in userspace
by putting the namespace temporarily into raw mode
(ndctl_namespace_set_raw_mode() from libndctl), but that is awkward
for management utilities.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
libnvdimm: fix namespace seed creation
|
|
Pull md fixes from Neil Brown:
"Some md fixes for 4.2
Several are tagged for -stable.
A few aren't because they are not very, serious or because they are in
the 'experimental' cluster code"
* tag 'md/4.2-fixes' of git://neil.brown.name/md:
md/raid5: clear R5_NeedReplace when no longer needed.
Fix read-balancing during node failure
md-cluster: fix bitmap sub-offset in bitmap_read_sb
md: Return error if request_module fails and returns positive value
md: Skip cluster setup in case of error while reading bitmap
md/raid1: fix test for 'was read error from last working device'.
md: Skip cluster setup for dm-raid
md: flush ->event_work before stopping array.
md/raid10: always set reshape_safe when initializing reshape_position.
md/raid5: avoid races when changing cache size.
|
|
A new BLK namespace "seed" device is created whenever the current seed
is successfully probed. However, if that namespace is assigned to a BTT
it may never directly experience a successful probe as it is a
subordinate device to a BTT configuration.
The effect of the current code is that no new namespaces can be
instantiated, after the seed namespace, to consume available BLK DPA
capacity. Fix this by treating a successful BTT probe event as a
successful probe event for the backing namespace.
Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Pull block fixes from Jens Axboe:
"Four smaller fixes for the current series. This contains:
- A fix for clones of discard bio's, that can cause data corruption.
From Martin.
- A fix for null_blk, where in certain queue modes it could access a
request after it had been freed. From Mike Krinkin.
- An error handling leak fix for blkcg, from Tejun.
- Also from Tejun, export of the functions that a file system needs
to implement cgroup writeback support"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Do a full clone when splitting discard bios
block: export bio_associate_*() and wbc_account_io()
blkcg: fix gendisk reference leak in blkg_conf_prep()
null_blk: fix use-after-free problem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"A couple important fixes.
- A block layer change which removed restriction on max transfer size
led to silent data corruption on some devices. A new quirk is
added to restore the old size limit for the reported device. If it
gets reported on more devices, we might have to consider restoring
the restriction for ATA devices by default.
- There finally is a SSD which is confirmed to cause data corruption
on TRIM regardless of which flavor is used. A new quirk is added
and the device is blacklisted
- Other device-specific workarounds"
* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Do not blacklist M510DC
libata: increase the timeout when setting transfer mode
libata: add ATA_HORKAGE_MAX_SEC_1024 to revert back to previous max_sectors limit
libata: force disable trim for SuperSSpeed S238
libata: add ATA_HORKAGE_NOTRIM
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for HP 250GB SATA disk VB0250EAVER
ata: pmp: add quirk for Marvell 4140 SATA PMP
|
|
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.2 rc4.
Note, most of the changes are for the sdhci-esdhc-imx controller,
which also required us to modify some related DTS files. Those
changes have been acked by the SoC maintainer.
MMC core:
- Fix a reference inbalance issue for power_ro_lock_show() sysfs handler
MMC host:
- omap_hsmmc: Fix IRQ errorhandling for CD, DTO, and CRC
- sdhci: Prevent a kernel panic while using DMA
- mtk-sd: Let it depend on HAS_DMA to prevent build errors
- sdhci-esdhc: Make 8BIT bus work
- sdhci-esdhc-imx: Fix some regressions for DT based platforms
- sdhci-pxav3: Fix a regression for DT based platforms"
* tag 'mmc-4.2-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-pxav3: fix platform_data is not initialized
dts: mmc: fsl-imx-esdhc: remove fsl,cd-controller support
mmc: sdhci-esdhc-imx: clear f_max in boarddata
mmc: sdhci-esdhc-imx: remove duplicated dts parsing
mmc: sdhci: make max-frequency property in device tree work
mmc: sdhci-esdhc-imx: move all non dt probe code into one function
mmc: sdhci-esdhc-imx: fix cd regression for dt platform
dts: imx7: fix sd card gpio polarity specified in device tree
dts: imx25: fix sd card gpio polarity specified in device tree
dts: imx6: fix sd card gpio polarity specified in device tree
dts: imx53: fix sd card gpio polarity specified in device tree
dts: imx51: fix sd card gpio polarity specified in device tree
mmc: sdhci-esdhc: Make 8BIT bus work
mmc: block: Add missing mmc_blk_put() in power_ro_lock_show()
mmc: MMC_MTK should depend on HAS_DMA
mmc: sdhci check parameters before call dma_free_coherent
mmc: omap_hsmmc: Handle BADA, DEB and CEB interrupts
mmc: omap_hsmmc: Fix DTO and DCRC handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A fix for the warnings/oops when handling HID devices with "unnamed"
LEDs and couple of other driver fixups""
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: goodix - fix touch coordinates on WinBook TW100 and TW700
Input: LEDs - skip unnamed LEDs
Input: usbtouchscreen - avoid unresponsive TSC-30 touch screen
Input: elantech - force resolution of 31 u/mm
Input: zforce - don't overwrite the stack
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"As well as some driver specific fixes there's several fixes here for
the core support for regulators supplying other regulators fixing both
an issue with ACPI support (which had never been tested before) and
some error handling and device removal issues that Javier noticed"
* tag 'regulator-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Fix memory leak in regulator_resolve_supply()
regulator: core: Increase refcount for regulator supply's module
regulator: core: Handle full constraints systems when resolving supplies
regulator: 88pm800: fix LDO vsel_mask value
regulator: max8973: Fix up control flag option for bias control
regulator: s2mps11: Fix GPIO suspend enable shift wrapping bug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small collection of pretty much unremarkable driver specific fixes
here plus the addition of a new device ID to spidev which requires no
other code changes"
* tag 'spi-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: imx: Fix small DMA transfers
spi: zynq: missing break statement
spi: SPI_ZYNQMP_GQSPI should depend on HAS_DMA
spi: spidev: add compatible value for LTC2488
spi: img-spfi: fix support for speeds up to 1/4th input clock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- kernel crash fixes for multitouch and wacom drivers, by Brent Adam
and Dan Carpenter
- cp2112 data packet race condition corruption fix, by Antonio Borneo
- a few new device IDs for wacom and microsoft drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: cp2112: fix to force single data-report reply
HID: wacom: Enable pad device for older Bamboo Touch tablets
HID: multitouch: Fix fields from pen report ID being interpreted for multitouch
HID: microsoft: Add quirk for MS Surface Type/Touch cover
HID: wacom: NULL dereferences on error in probe()
|
|
The touchscreen on the WinBook TW100 and TW700 don't match the default
display, with 0,0 touches being reported when touching at the bottom
right of the screen.
1280,800 0,800
+-------------+
| |
| |
| |
+-------------+
1280,0 0,0
It's unfortunately impossible to detect this problem with data from the
DSDT, or other auxiliary metadata, so fallback to quirking this specific
model of tablet instead.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Devices may declare more LEDs than what is known to input-leds
(HID does this for some devices). Instead of showing ugly warnings
on connect and, even worse, oopsing on disconnect, let's simply
ignore LEDs that are not known to us.
Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
'spi/fix/mg-spfi' and 'spi/fix/spidev' into spi-linus
|
|
'regulator/fix/max8973', 'regulator/fix/s2mps11' and 'regulator/fix/supply' into regulator-linus
|
|
|
|
DMA transfers must be greater than the watermark level size. spi_imx->rx_wml
and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct
spi_transfer contains the transfer len in bytes. Fix the check if DMA is
possible for a transfer accordingly. This fixes transfers with sizes between
33 and 128 bytes for which previously was claimed that DMA is possible.
Fixes: f62caccd12c17e4 (spi: spi-imx: add DMA support)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
pdev->dev.platform_data is not initialized if match is true in function
sdhci_pxav3_probe. Just local variable pdata is assigned the return value
from function pxav3_get_mmc_pdata().
static int sdhci_pxav3_probe(struct platform_device *pdev) {
struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
...
if (match) {
ret = mmc_of_parse(host->mmc);
if (ret)
goto err_of_parse;
sdhci_get_of_property(pdev);
pdata = pxav3_get_mmc_pdata(dev);
}
...
}
Signed-off-by: Jingju Hou <houjingj@marvell.com>
Fixes: b650352dd3df("mmc: sdhci-pxa: Add device tree support")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After commit 8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
it's not used anymore.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After commit 8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need those duplicated parsing anymore.
Note: fsl,cd-controller is also deleted due to the driver does
not support controller card detection anymore after switch to runtime pm.
And there's no user of it right now in device tree.
wp-gpios is kept because we're still support fsl,wp-controller,
so we need a way to check if it's gpio wp or controller wp.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Device tree provides option to specify the max freqency with property
"max-frequency" in dts and common parse function mmc_of_parse() will
parse it and use this value to set host->f_max to tell the MMC core
the maxinum frequency the host works.
However, current sdhci driver will finally overwrite this value with
host->max_clk regardless of the max-frequency property.
This patch makes sure not overwrite the max-frequency set from device
tree and do basic sanity check.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This is an incremental fix of commit
e62bd351b("mmc: sdhci-esdhc-imx: Do not break platform data boards").
After commit 8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need to run the check of boarddata->wp_type/cd_type/max_bus_width
again for dt platform since those are already handled by mmc_of_parse().
Current code only exclude the checking of wp_type for dt platform which
does not make sense.
This patch moves all non dt probe code into one function.
Besides, since we only support SD3.0/eMMC HS200 for dt platform, the
support_vsel checking and ultra high speed pinctrl state are also merged
into sdhci_esdhc_imx_probe_dt.
Then we have two separately probe function for dt and non dt type.
This can make the driver probe more clearly.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Current card detect probe process is that when driver finds a valid
ESDHC_CD_GPIO, it will clear the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION
which is set by default for all esdhc/usdhc controllers.
Then host driver will know there's a valid card detect function.
Commit 8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
breaks GPIO CD function for dt platform that it will return directly
when find ESDHC_CD_GPIO for dt platform which result in the later wrongly
to keep SDHCI_QUIRK_BROKEN_CARD_DETECTION for all dt platforms.
Then MMC_CAP_NEEDS_POLL will be used instead even there's a valid
GPIO card detect.
This patch adds back this function and follows the original approach to
clear the quirk if find an valid CD GPIO for dt platforms.
Fixes: 8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Support for 8BIT bus with was added some time ago to sdhci-esdhc but
then missed to remove the 8BIT from the reserved bit mask which made
8BIT non functional.
Fixes: 66b50a00992d ("mmc: esdhc: Add support for 8-bit bus width and..")
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Enclosing mmc_blk_put() is missing in power_ro_lock_show() sysfs handler,
let's add it.
Fixes: add710eaa886 ("mmc: boot partition ro lock support")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If NO_DMA=y:
ERROR: "dma_alloc_coherent" [drivers/mmc/host/mtk-sd.ko] undefined!
ERROR: "dma_unmap_sg" [drivers/mmc/host/mtk-sd.ko] undefined!
ERROR: "dma_map_sg" [drivers/mmc/host/mtk-sd.ko] undefined!
ERROR: "dma_free_coherent" [drivers/mmc/host/mtk-sd.ko] undefined!
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We should not call dma_free_coherent if host->adma_table is NULL,
otherwise may trigger panic.
Fixes: d1e49f77d7c7 ("mmc: sdhci: convert ADMA descriptors to a...")
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Sometimes BADA, DEB or CEB error interrupts occur when sd card is
unplugged during data transfer. These interrupts are currently ignored
by the interrupt handler. But, this results in card not being
recognised on subsequent insertion. This is because mmcqd is waiting
forever for the data transfer(for which error occurred) to complete.
Fix this, by reporting BADA, DEB, CEB errors to mmc-core as -EILSEQ, so
that the core can do appropriate handling.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
