| Age | Commit message (Collapse) | Author |
|---|
|
A small subset of pins and functions are exposed. The selection of pins
and functions is driven by the development of OpenBMC[1] on the
AST2500 SoC, particularly around booting the IBM Witherspoon platform.
[1] https://github.com/openbmc/docs
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A subset of the pins and functions are exposed. The selection of
functions and pins is driven by the development of OpenBMC[1] on the
AST2400 SoC, particularly around booting the OpenPOWER Palmetto
development machine.
[1] https://github.com/openbmc/docs
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Aspeed SoCs typically provide more than 200 pins for GPIO and other
functions. The signal enabled on a pin is determined on a priority
basis, where a given pin can provide a number of different signal types.
In addition to the priority levels, the Aspeed pin controllers describe
the signal active on a pin by compound logical expressions involving
multiple operators, registers and bits. Some difficulty arises as a
pin's function bit masks for each priority level are frequently not the
same (i.e. we cannot just flip a bit to change from a high to low
priority signal), or even in the same register(s). Some configuration
bits affect multiple pins, while in other cases the signals for a bus
must each be enabled individually.
Together, these features give rise to some complexity in the
implementation. A more complete description of the complexities is
provided in the associated header file.
The patch doesn't implement pinctrl/pinmux/pinconf for any particular
Aspeed SoC, rather it adds the framework for defining pinmux
configurations.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
sd_emmc_a is used a controller for the SDIO modules. This adds the pin
configuration for the SDIO controller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It contains pin 50 instead of pin 40.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Add support for R-Car M3-W
Add initial support for the Pin Function Controller on the Renesas R-Car
M3-W SoC:
- Basic definitions,
- SCIF (serial) pins, groups and functions,
- SDHI pins, groups and functions.
|
|
cat /sys/kernel/debug/pinctrl/${pinctrl}/pinconf-groups output is
hardly readable, if a pin group contains more than one pin the output
is glued and looks like this:
MX6Q_PAD_SD1_DAT0: 0x17071MX6Q_PAD_SD1_CMD: 0x17071MX6Q_PAD_SD1_CLK: 0x17071
Add two space indentation and a new line separator to improve
readability of the output.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Makefile currently controlling compilation of this code is:
drivers/pinctrl/sirf/pinctrl-sirf.o
--> drivers/pinctrl/sirf/Makefile:obj-y += pinctrl-sirf.o
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rongjun Ying <rongjun.ying@csr.com>
Cc: Yuping Luo <yuping.luo@csr.com>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Makefile currently controlling compilation of this code is:
drivers/pinctrl/sirf/pinctrl-atlas7.o
---> drivers/pinctrl/sirf/Makefile:obj-y += pinctrl-atlas7.o
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_ROCKCHIP
drivers/pinctrl/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-gpio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/nomadik/Kconfig:config PINCTRL_NOMADIK
drivers/pinctrl/nomadik/Kconfig: bool "Nomadik pin controller driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
config PINCTRL_ABX500
bool "ST-Ericsson ABx500 family Mixed Signal Circuit gpio functions"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Note that MODULE_ALIAS is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Makefile currently controlling compilation of this code is:
drivers/pinctrl/mediatek/pinctrl-mtk-common.o
---> drivers/pinctrl/mediatek/Makefile:obj-y += pinctrl-mtk-common.o
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file doesn't need that.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Hongzhou Yang <hongzhou.yang@mediatek.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add support for PWM pins, for EE and AO domains.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.9
- Bias and DU support for R-Car H3,
- Basic R-Car V2H support,
- Cleanups and fixes.
|
|
This adds the IR remote receiver to the AO domain devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
of_match_device could return NULL, and so cause a NULL pointer
dereference later at line 1009:
pinctrl_data = match->data;
For fixing this problem, we use of_device_get_match_data(), this will
simplify the code a little by using a standard function for
getting the match data.
Reported-by: coverity (CID 1324136)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Because chained_irq_enter() has already called chip->irq_mask() and
chip->irq_ack(), also chained_irq_exit() will call chip->irq_unmask(),
so it's not necessary to call chip->irq_*() here.
Signed-off-by: Perr Zhang <strongbox8@zoho.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[Hand-edited from whitespace damaged patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The driver originally supported more domains (register ranges) per
pinctrl device, but since commit 9dab1868ec0d ("pinctrl: amlogic: Make
driver independent from two-domain configuration") each device gets
assigned a single domain and we instantiate multiple pinctrl devices
in the DT.
Therefore, now the 'meson_domain' and 'meson_domain_data' structures
don't have any reason to exist and can be removed to make the model
simpler to understand. This commit doesn't change behavior.
Tested on a Odroid-C2.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds SDHI pins, groups and functions to R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds SCIF{0,1,2,3,4,5} pins, groups and functions to R8A7796
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds initial pinctrl driver to support for the R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[uli: rebased on top of renesas-drivers]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Only the DU parallel RGB output signals are included, HDMI and TCON pins
will be added in separate groups.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch allows to use the second parameter of gpio
specifier, which is used to specify whether the gpio is
active high or low.
Simply remove specific of_xlate callback() and of_gpio_n_cells
and use default one set by of_gpiochip_add() which allows
to use second parameter gpio specifier.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,x;
@@
- if (of_get_property(e1,e2,NULL))
- x = true;
- else
- x = false;
+ x = of_property_read_bool(e1,e2);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The drivers don't really need to know which PMIC they're for, so
make a generic binding for them. This alleviates us from updating
the drivers every time a new PMIC comes out. It's still
recommended that we update the binding with new PMIC models and
always specify the specific model for the MPPs and gpios before
the generic compatible string in devicetree, but this at least
cuts down on adding more and more compatible strings to the
drivers until we actually need them.
Cc: <devicetree@vger.kernel.org>
Acked-by: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add the SPDIF mux functionality to the pinctrl for the Allwinner A31
SoC.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add DU pin groups to the R8A7792 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add VIN[0-5] pin groups to the R8A7792 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[geert: Fix VI1_D14_G6_Y6 and VI1_D15_G7_Y7 pins]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This source file handles r8a7795 only, which is not the sole member of
the R-Car Gen3 family.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add CAN0/1 data/clock pin groups to R8A7792 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add SDHI0 pin groups to the R8A7792 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the EtherAVB pin groups to the R8A7792 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the PFC support for the R8A7792 SoC including pin groups for some
on-chip devices such as SCIF, INTC, and LBSC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[geert: s/LSBC/LBSC/]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The PORT_GP_CFG_<n>() macros take up more than 80 columns -- and not for
a good reason. Make the header file checkpatch.pl-proof at least in this
respect...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Implements pull-up and pull-down. On this SoC there is no simple mapping of
GP pins to bias register bits, so we need a table.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Pull more block fixes from Jens Axboe:
"As mentioned in the pull the other day, a few more fixes for this
round, all related to the bio op changes in this series.
Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf. I
wanted to do that change right after or right before -rc1, so that
risk of conflict was reduced. I just rebased the series on top of
current master, and no new ->bi_rw usage has snuck in"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: rename bio bi_rw to bi_opf
target: iblock_execute_sync_cache() should use bio_set_op_attrs()
mm: make __swap_writepage() use bio_set_op_attrs()
block/mm: make bdev_ops->rw_page() take a bool for read/write
|
|
Pull drm zpos property support from Dave Airlie:
"This tree was waiting on some media stuff I hadn't had time to get a
stable branchpoint off, so I just waited until it was all in your tree
first.
It's been around a bit on the list and shouldn't affect anything
outside adding the generic API and moving some ARM drivers to using
it"
* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
drm: rcar: use generic code for managing zpos plane property
drm/exynos: use generic code for managing zpos plane property
drm: sti: use generic zpos for plane
drm: add generic zpos property
|
|
Since commit 63a4cc24867d, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The original commit missed this function, it needs to mark it a
write flush.
Cc: Mike Christie <mchristi@redhat.com>
Fixes: e742fc32fcb4 ("target: use bio op accessors")
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Commit abf545484d31 changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.
Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more vfs updates from Al Viro:
"Assorted cleanups and fixes.
In the "trivial API change" department - ->d_compare() losing 'parent'
argument"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
cachefiles: Fix race between inactivating and culling a cache object
9p: use clone_fid()
9p: fix braino introduced in "9p: new helper - v9fs_parent_fid()"
vfs: make dentry_needs_remove_privs() internal
vfs: remove file_needs_remove_privs()
vfs: fix deadlock in file_remove_privs() on overlayfs
get rid of 'parent' argument of ->d_compare()
cifs, msdos, vfat, hfs+: don't bother with parent in ->d_compare()
affs ->d_compare(): don't bother with ->d_inode
fold _d_rehash() and __d_rehash() together
fold dentry_rcuwalk_invalidate() into its only remaining caller
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull qstr constification updates from Al Viro:
"Fairly self-contained bunch - surprising lot of places passes struct
qstr * as an argument when const struct qstr * would suffice; it
complicates analysis for no good reason.
I'd prefer to feed that separately from the assorted fixes (those are
in #for-linus and with somewhat trickier topology)"
* 'work.const-qstr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
qstr: constify instances in adfs
qstr: constify instances in lustre
qstr: constify instances in f2fs
qstr: constify instances in ext2
qstr: constify instances in vfat
qstr: constify instances in procfs
qstr: constify instances in fuse
qstr constify instances in fs/dcache.c
qstr: constify instances in nfs
qstr: constify instances in ocfs2
qstr: constify instances in autofs4
qstr: constify instances in hfs
qstr: constify instances in hfsplus
qstr: constify instances in logfs
qstr: constify dentry_init_security
|
|
Pull virtio/vhost updates from Michael Tsirkin:
- new vsock device support in host and guest
- platform IOMMU support in host and guest, including compatibility
quirks for legacy systems.
- misc fixes and cleanups.
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
VSOCK: Use kvfree()
vhost: split out vringh Kconfig
vhost: detect 32 bit integer wrap around
vhost: new device IOTLB API
vhost: drop vringh dependency
vhost: convert pre sorted vhost memory array to interval tree
vhost: introduce vhost memory accessors
VSOCK: Add Makefile and Kconfig
VSOCK: Introduce vhost_vsock.ko
VSOCK: Introduce virtio_transport.ko
VSOCK: Introduce virtio_vsock_common.ko
VSOCK: defer sock removal to transports
VSOCK: transport-specific vsock_transport functions
vhost: drop vringh dependency
vop: pull in vhost Kconfig
virtio: new feature to detect IOMMU device quirk
balloon: check the number of available pages in leak balloon
vhost: lockless enqueuing
vhost: simplify work flushing
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.8. Also includes is a
minor SSB cleanup as SSB code traditionally is merged through the MIPS
tree:
ATH25:
- MIPS: Add default configuration for ath25
Boot:
- For zboot, copy appended dtb to the end of the kernel
- store the appended dtb address in a variable
BPF:
- Fix off by one error in offset allocation
Cobalt code:
- Fix typos
Core code:
- debugfs_create_file returns NULL on error, so don't use IS_ERR for
testing for errors.
- Fix double locking issue in RM7000 S-cache code. This would only
affect RM7000 ARC systems on reboot.
- Fix page table corruption on THP permission changes.
- Use compat_sys_keyctl for 32 bit userspace on 64 bit kernels.
David says, there are no compatibility issues raised by this fix.
- Move some signal code around.
- Rewrite r4k count/compare clockevent device registration such that
min_delta_ticks/max_delta_ticks files are guaranteed to be
initialized.
- Only register r4k count/compare as clockevent device if we can
assume the clock to be constant.
- Fix MSA asm warnings in control reg accessors
- uasm and tlbex fixes and tweaking.
- Print segment physical address when EU=1.
- Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO.
- CP: Allow booting by VP other than VP 0
- Cache handling fixes and optimizations for r4k class caches
- Add hotplug support for R6 processors
- Cleanup hotplug bits in kconfig
- traps: return correct si code for accessing nonmapped addresses
- Remove cpu_has_safe_index_cacheops
Lantiq:
- Register IRQ handler for virtual IRQ number
- Fix EIU interrupt loading code
- Use the real EXIN count
- Fix build error.
Loongson 3:
- Increase HPET_MIN_PROG_DELTA and decrease HPET_MIN_CYCLES
Octeon:
- Delete built-in DTB pruning code for D-Link DSR-1000N.
- Clean up GPIO definitions in dlink_dsr-1000n.dts.
- Add more LEDs to the DSR-100n DTS
- Fix off by one in octeon_irq_gpio_map()
- Typo fixes
- Enable SATA by default in cavium_octeon_defconfig
- Support readq/writeq()
- Remove forced mappings of USB interrupts.
- Ensure DMA descriptors are always in the low 4GB
- Improve USB reset code for OCTEON II.
Pistachio:
- Add maintainers entry for pistachio SoC Support
- Remove plat_setup_iocoherency
Ralink:
- Fix pwm UART in spis group pinmux.
SSB:
- Change bare unsigned to unsigned int to suit coding style
Tools:
- Fix reloc tool compiler warnings.
Other:
- Delete use of ARCH_WANT_OPTIONAL_GPIOLIB"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (61 commits)
MIPS: mm: Fix definition of R6 cache instruction
MIPS: tools: Fix relocs tool compiler warnings
MIPS: Cobalt: Fix typo
MIPS: Octeon: Fix typo
MIPS: Lantiq: Fix build failure
MIPS: Use CPHYSADDR to implement mips32 __pa
MIPS: Octeon: Dlink_dsr-1000n.dts: add more leds.
MIPS: Octeon: Clean up GPIO definitions in dlink_dsr-1000n.dts.
MIPS: Octeon: Delete built-in DTB pruning code for D-Link DSR-1000N.
MIPS: store the appended dtb address in a variable
MIPS: ZBOOT: copy appended dtb to the end of the kernel
MIPS: ralink: fix spis group pinmux
MIPS: Factor o32 specific code into signal_o32.c
MIPS: non-exec stack & heap when non-exec PT_GNU_STACK is present
MIPS: Use per-mm page to execute branch delay slot instructions
MIPS: Modify error handling
MIPS: c-r4k: Use SMP calls for CM indexed cache ops
MIPS: c-r4k: Avoid small flush_icache_range SMP calls
MIPS: c-r4k: Local flush_icache_range cache op override
MIPS: c-r4k: Split r4k_flush_kernel_vmap_range()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom
iProc, STMPE and ChromeOS EC controllers"
* tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
regulator: pwm: Document pwm-dutycycle-unit and pwm-dutycycle-range
regulator: pwm: Support extra continuous mode cases
pwm: Add ChromeOS EC PWM driver
dt-bindings: pwm: Add binding for ChromeOS EC PWM
mfd: cros_ec: Add EC_PWM function definitions
mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper
pwm: atmel: Use of_device_get_match_data()
pwm: atmel: Fix checkpatch warnings
pwm: atmel: Fix disabling of PWM channels
dt-bindings: pwm: Add R-Car H3 device tree bindings
pwm: rcar: Use ARCH_RENESAS
pwm: tegra: Add support for Tegra186
dt-bindings: pwm: tegra: Add compatible string for Tegra186
pwm: tegra: Avoid overflow when calculating duty cycle
pwm: tegra: Allow 100 % duty cycle
pwm: tegra: Add support for reset control
pwm: tegra: Rename mmio_base to regs
pwm: tegra: Remove useless padding
pwm: tegra: Drop NUM_PWM macro
pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value
...
|
|
Pull NTB updates from Jon Mason:
"NTB bug fixes for the ntb_tool and ntb_perf, and improvements to the
ntb_perf and ntb_pingpong for increased debugability.
Also, modification to the ntb_transport layer to increase/decrease
the number of transport entries depending on the ring size"
* tag 'ntb-4.8' of git://github.com/jonmason/ntb:
NTB: ntb_hw_intel: use local variable pdev
NTB: ntb_hw_intel: show BAR size in debugfs info
ntb_test: Add a selftest script for the NTB subsystem
ntb_perf: clear link_is_up flag when the link goes down.
ntb_pingpong: Add a debugfs file to get the ping count
ntb_tool: Add link status and files to debugfs
ntb_tool: Postpone memory window initialization for the user
ntb_perf: Wait for link before running test
ntb_perf: Return results by reading the run file
ntb_perf: Improve thread handling to increase robustness
ntb_perf: Schedule based on time not on performance
ntb_transport: Check the number of spads the hardware supports
ntb_tool: Add memory window debug support
ntb_perf: Allow limiting the size of the memory windows
NTB: allocate number transport entries depending on size of ring size
ntb_tool: BUG: Ensure the buffer size is large enough to return all spads
ntb_tool: Fix infinite loop bug when writing spad/peer_spad file
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore fixes from Kees Cook:
"Fixes for pstore ramoops driver to catch bad kfree() and to use better
DT bindings"
* tag 'pstore-v4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
ramoops: use persistent_ram_free() instead of kfree() for freeing prz
ramoops: use DT reserved-memory bindings
|
|
Pull SCSI fixes from James Bottomley:
"This is seven basic fixes (plus one MAINTAINER update) which came in
close to the merge window"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
ipr: Fix error return code in ipr_probe_ioa()
fcoe: add missing destroy_workqueue() on error in fcoe_init()
lpfc: Fix possible NULL pointer dereference
fcoe: Use default VLAN for FIP VLAN discovery
ipr: Wait to do async scan until scsi host is initialized
MAINTAINERS: Update cxlflash maintainers
cxlflash: Verify problem state area is mapped before notifying shutdown
lpfc: fix oops in lpfc_sli4_scmd_to_wqidx_distr() from lpfc_send_taskmgmt()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable dm-flakey fix to error read IO during the 'down_interval'
- a DM core suspend fix to establish the SUSPENDED flag before dropping
the SUSPENDING flag
- a blk-mq request-based DM (dm-mq) dm_stop_queue() fix to properly
stop the blk-mq hw_queues (and cancel pending requeue work); also
set/clear QUEUE_FLAG_STOPPED when stopping/starting the dm-mq
request_queue.
- a DM multipath fix to harden locking of in-core state flags in the
face of concurrent access while handling path failures under heavy
IO.
- a few small DM raid fixes to edge cases caught with further testing.
* tag 'dm-4.8-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm raid: fix use of wrong status char during resynchronization
dm raid: constructor fails on non-zero incompat_features
dm raid: fix processing of max_recovery_rate constructor flag
dm: set DMF_SUSPENDED* _before_ clearing DMF_NOFLUSH_SUSPENDING
dm rq: fix the starting and stopping of blk-mq queues
dm mpath: add locking to multipath_resume and must_push_back
dm flakey: error READ bios during the down_interval
|
