| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Again, a batch that's been sitting a couple of weeks, mostly because
I anticipated a bit more material but it didn't show up -- which is
good.
These are all your garden variety fixes for ARM platforms.
The most visible issue fixed here is probably the SMP reset issue on
OMAP, the rest are minor stuff"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: allwinner: a64: add pmu0 regs for USB PHY
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
reset: add exported __reset_control_get, return NULL if optional
ARM: orion5x: only call into phylib when available
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
ARM: sun8i: a33: add operating-points-v2 property to all nodes
ARM: sun8i: a33: remove highest OPP to fix CPU crashes
|
|
Pull block fixes from Jens Axboe:
"Four small fixes.
Three of them fix the same error in NVMe, in loop, fc, and rdma
respectively. The last fix from Ming fixes a regression in this
series, where our bvec gap logic was wrong and causes an oops on
NVMe for certain conditions"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix bio_will_gap() for first bvec with offset
nvme-fc: Fix sqsize wrong assignment based on ctrl MQES capability
nvme-rdma: Fix sqsize wrong assignment based on ctrl MQES capability
nvme-loop: Fix sqsize wrong assignment based on ctrl MQES capability
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fix from Greg KH:
"Here is a single tty core revert for a patch that was reported to
cause problems.
The original issue is one that we have lived with for decades, so
trying to scramble to fix the fix in time for 4.11-final does not make
sense due to the fragility of the tty ldisc layer. Just reverting it
makes sense for now"
* tag 'tty-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "tty: don't panic on OOM in tty_set_ldisc()"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull nvdimm fixes from Dan Williams:
"A small crop of lockdep, sleeping while atomic, and other fixes /
band-aids in advance of the full-blown reworks targeting the next
merge window. The largest change here is "libnvdimm: fix blk free
space accounting" which deletes a pile of buggy code that better
testing would have caught before merging. The next change that is
borderline too big for a late rc is switching the device-dax locking
from rcu to srcu, I couldn't think of a smaller way to make that fix.
The __copy_user_nocache fix will have a full replacement in 4.12 to
move those pmem special case considerations into the pmem driver. The
"libnvdimm: band aid btt vs clear poison locking" commit admits that
our error clearing support for btt went in broken, so we just disable
it in 4.11 and -stable. A replacement / full fix is in the pipeline
for 4.12
Some of these would have been caught earlier had DEBUG_ATOMIC_SLEEP
been enabled on my development station. I wonder if we should have:
config DEBUG_ATOMIC_SLEEP
default PROVE_LOCKING
...since I mistakenly thought I got both with PROVE_LOCKING=y.
These have received a build success notification from the 0day robot,
and some have appeared in a -next release with no reported issues"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
x86, pmem: fix broken __copy_user_nocache cache-bypass assumptions
device-dax: switch to srcu, fix rcu_read_lock() vs pte allocation
libnvdimm: band aid btt vs clear poison locking
libnvdimm: fix reconfig_mutex, mmap_sem, and jbd2_handle lockdep splat
libnvdimm: fix blk free space accounting
acpi, nfit, libnvdimm: fix interleave set cookie calculation (64-bit comparison)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is seven small fixes which are all for user visible issues that
fortunately only occur in rare circumstances.
The most serious is the sr one in which QEMU can cause us to read
beyond the end of a buffer (I don't think it's exploitable, but just
in case).
The next is the sd capacity fix which means all non 512 byte sector
drives greater than 2TB fail to be correctly sized.
The rest are either in new drivers (qedf) or on error legs"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ipr: do not set DID_PASSTHROUGH on CHECK CONDITION
scsi: aacraid: fix PCI error recovery path
scsi: sd: Fix capacity calculation with 32-bit sector_t
scsi: qla2xxx: Add fix to read correct register value for ISP82xx.
scsi: qedf: Fix crash due to unsolicited FIP VLAN response.
scsi: sr: Sanity check returned mode data
scsi: sd: Consider max_xfer_blocks if opt_xfer_blocks is unusable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just a small update to xpad driver to recognize yet another gamepad,
and another change making sure userio.h is exported"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - add support for Razer Wildcat gamepad
uapi: add missing install of userio.h
|
|
Pull networking fixes from David Miller:
"Things seem to be settling down as far as networking is concerned,
let's hope this trend continues...
1) Add iov_iter_revert() and use it to fix the behavior of
skb_copy_datagram_msg() et al., from Al Viro.
2) Fix the protocol used in the synthetic SKB we cons up for the
purposes of doing a simulated route lookup for RTM_GETROUTE
requests. From Florian Larysch.
3) Don't add noop_qdisc to the per-device qdisc hashes, from Cong
Wang.
4) Don't call netdev_change_features with the team lock held, from
Xin Long.
5) Revert TCP F-RTO extension to catch more spurious timeouts because
it interacts very badly with some middle-boxes. From Yuchung
Cheng.
6) Fix the loss of error values in l2tp {s,g}etsockopt calls, from
Guillaume Nault.
7) ctnetlink uses bit positions where it should be using bit masks,
fix from Liping Zhang.
8) Missing RCU locking in netfilter helper code, from Gao Feng.
9) Avoid double frees and use-after-frees in tcp_disconnect(), from
Eric Dumazet.
10) Don't do a changelink before we register the netdevice in
bridging, from Ido Schimmel.
11) Lock the ipv6 device address list properly, from Rabin Vincent"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
netfilter: ipt_CLUSTERIP: Fix wrong conntrack netns refcnt usage
netfilter: nft_hash: do not dump the auto generated seed
drivers: net: usb: qmi_wwan: add QMI_QUIRK_SET_DTR for Telit PID 0x1201
ipv6: Fix idev->addr_list corruption
net: xdp: don't export dev_change_xdp_fd()
bridge: netlink: register netdevice before executing changelink
bridge: implement missing ndo_uninit()
bpf: reference may_access_skb() from __bpf_prog_run()
tcp: clear saved_syn in tcp_disconnect()
netfilter: nf_ct_expect: use proper RCU list traversal/update APIs
netfilter: ctnetlink: skip dumping expect when nfct_help(ct) is NULL
netfilter: make it safer during the inet6_dev->addr_list traversal
netfilter: ctnetlink: make it safer when checking the ct helper name
netfilter: helper: Add the rcu lock when call __nf_conntrack_helper_find
netfilter: ctnetlink: using bit to represent the ct event
netfilter: xt_TCPMSS: add more sanity tests on tcph->doff
net: tcp: Increase TCP_MIB_OUTRSTS even though fail to alloc skb
l2tp: don't mask errors in pppol2tp_getsockopt()
l2tp: don't mask errors in pppol2tp_setsockopt()
tcp: restrict F-RTO to work-around broken middle-boxes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"The irq department provides:
- two fixes for the CPU affinity spread infrastructure to prevent
unbalanced spreading in corner cases which leads to horrible
performance, because interrupts are rather aggregated than spread
- add a missing spinlock initializer in the imx-gpcv2 init code"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-imx-gpcv2: Fix spinlock initialization
irq/affinity: Fix extra vecs calculation
irq/affinity: Fix CPU spread for unbalanced nodes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Thomas Gleixner:
"Three fixes from EFI land:
- prevent accessing a Graphic Output Device (GOP) which the kernel
does not know to handle
- prevent PCI reconfiguration to modify a BAR which covers the
framebuffer because that's already in use through the EFI GOP
interface
- avoid reserving EFI runtime regions as this results in bogus memory
mappings"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Don't try to reserve runtime regions
efi/fb: Avoid reconfiguration of BAR that covers the framebuffer
efi/libstub: Skip GOP with PIXEL_BLT_ONLY format
|
|
Pull fbdev fixes from Bartlomiej Zolnierkiewicz:
- fix probing time checks in omapfb driver (regression fix)
- fix optional VBAT support in ssd1307fb driver (regression fix)
- fix connecting to backend in xen-fbfront driver
* tag 'fbdev-v4.11-rc6' of git://github.com/bzolnier/linux:
fbdev: omapfb: delete check_required_callbacks()
xen, fbfront: fix connecting to backend
fbdev/ssd1307fb: fix optional VBAT support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a cpufreq core regression related to CPU online/offline and
several issues in the turbostat and cpupower utilities.
Specifics:
- Allow CPUs to be put back online even if the cpufreq driver is
unable to work with them (eg. due to missing information from
platform firmware), which was the previous behavior expected by
users, but changed in the 4.9 time frame (Chen Yu).
- Fix a few minor issues in the turbostat utility, introduced mostly
during the recent update of it (Len Brown, Doug Smythies).
- Fix a cpupower utility bug causing it to report incorrect values
for turbo frequencies in some cases (Ben Hutchings)"
* tag 'pm-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpupower: Fix turbo frequency reporting for pre-Sandy Bridge cores
cpufreq: Bring CPUs up even if cpufreq_online() failed
tools/power turbostat: update version number
tools/power turbostat: fix impossibly large CPU%c1 value
tools/power turbostat: turbostat.8 add missing column definitions
tools/power turbostat: update HWP dump to decimal from hex
tools/power turbostat: enable package THERM_INTERRUPT dump
tools/power turbostat: show missing Core and GFX power on SKL and KBL
tools/power turbostat: bugfix: GFXMHz column not changing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert a recent ACPICA commit that turned out to be problematic
and fix a device enumeration breakage from the 4.8 cycle.
Specifics:
- Revert a recent ACPICA commit targeted at catching firmware bugs
which promptly did that and caused functional problems to appear
(Rafael Wysocki).
- Fix a device enumeration problem introduced in the 4.8 time frame
which caused the ACPI docking station driver to report incorrect
status via sysfs among other things (Rafael Wysocki)"
* tag 'acpi-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPICA: Resources: Not a valid resource if buffer length too long"
ACPI / scan: Set the visited flag for all enumerated devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull CONFIG_STRICT_DEVMEM fix from Kees Cook:
"Fixes /dev/mem to read back zeros for System RAM areas in the 1MB
exception area on x86 to avoid exposing RAM or tripping hardened
usercopy"
* tag 'devmem-v4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
mm: Tighten x86 /dev/mem with zeroing reads
|
|
Pull virtio fixes from Michael S. Tsirkin:
"virtio oops fixes
The virtio pci rework using shared interrupts caused a lot of issues.
We tried to fix them but run out of time. Revert for now, and revisit
the issue for the next kernel.
Luckily we are able to do this without loosing automatic interrupt
NUMA affinity which was the main motivator for the rework"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-pci: Remove affinity hint before freeing the interrupt
Revert "virtio_pci: remove struct virtio_pci_vq_info"
Revert "virtio_pci: use shared interrupts for virtqueues"
Revert "virtio_pci: don't duplicate the msix_enable flag in struct pci_dev"
Revert "virtio_pci: simplify MSI-X setup"
Revert "virtio_pci: fix out of bound access for msix_names"
MAINTAINERS: fix virtio file pattern
virtio_console: fix uninitialized variable use
virtio_net: clear MTU when out of range
virtio: allow drivers to validate features
virtio_net: enable big packets for large MTU values
|
|
Commit 561eb9d09a93 ("fbdev: omap/lcd: Make callbacks optional") made
panel callbacks optional but forgot to update check_required_callbacks().
As a result many (all?) OMAP systems using omapfb will crash at boot.
Fix by deleting the whole function.
Fixes: 561eb9d09a93 ("fbdev: omap/lcd: Make callbacks optional")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
* acpi-scan-fixes:
ACPI / scan: Set the visited flag for all enumerated devices
* acpica-fixes:
Revert "ACPICA: Resources: Not a valid resource if buffer length too long"
|
|
This reverts commit 5362544bebe85071188dd9e479b5a5040841c895 as it is
reported to cause a reproducable crash.
Fixes: 5362544bebe8 ("tty: don't panic on OOM in tty_set_ldisc()")
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: <syzkaller@googlegroups.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
|
|
The raw_spinlock in the IMX GPCV2 interupt chip is not initialized before
usage. That results in a lockdep splat:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Add the missing raw_spin_lock_init() to the setup code.
Fixes: e324c4dc4a59 ("irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources")
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: shawnguo@kernel.org
Cc: andrew.smirnov@gmail.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20170413222731.5917-1-tyler.baker@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The copy_page is optimized memcpy for page-alinged address. If it is
used with non-page aligned address, it can corrupt memory which means
system corruption. With zram, it can happen with
1. 64K architecture
2. partial IO
3. slub debug
Partial IO need to allocate a page and zram allocates it via kmalloc.
With slub debug, kmalloc(PAGE_SIZE) doesn't return page-size aligned
address. And finally, copy_page(mem, cmem) corrupts memory.
So, this patch changes it to memcpy.
Actuaully, we don't need to change zram_bvec_write part because zsmalloc
returns page-aligned address in case of PAGE_SIZE class but it's not
good to rely on the internal of zsmalloc.
Note:
When this patch is merged to stable, clear_page should be fixed, too.
Unfortunately, recent zram removes it by "same page merge" feature so
it's hard to backport this patch to -stable tree.
I will handle it when I receive the mail from stable tree maintainer to
merge this patch to backport.
Fixes: 42e99bd ("zram: optimize memory operations with clear_page()/copy_page()")
Link: http://lkml.kernel.org/r/1492042622-12074-2-git-send-email-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In zram_rw_page, the logic to get offset is wrong by operator precedence
(i.e., "<<" is higher than "&"). With wrong offset, zram can corrupt
the user's data. This patch fixes it.
Fixes: 8c7f01025 ("zram: implement rw_page operation of zram")
Link: http://lkml.kernel.org/r/1492042622-12074-1-git-send-email-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Telit LE920A4 uses the same pid 0x1201 of LE920, but modem
implementation is different, since it requires DTR to be set for
answering to qmi messages.
This patch replaces QMI_FIXED_INTF with QMI_QUIRK_SET_DTR: tests on
LE920 have been performed in order to verify backward compatibility.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Revert commit 57707a9a7780 (ACPICA: Resources: Not a valid resource if
buffer length too long) as it is reported to prevent the TPM module
from loading on Lenovo X60 with Coreboot.
It also causes new confusing warnings to show up in the kernel log.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195311
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Two pin control fixes arriving late, these are hopefully the last pin
control fixes I send this kernel cycle. A Chromebook and an Exynos SoC
thingie.
The Exynos patch is pretty big, it is fixing unbroken a breakage
caused by yours truly when trying to figure out the merge mess with
the different Samsung platforms for this merge window. Sorry about
that. We have countered this situation by assigning a Samsung pin
control submaintainer to catch stuff earlier.
Summary:
- Make the Acer Chromebook keyboard work again with the Intel
Cherryview driver.
- Fix a merge error in the Exynos 5433 driver"
* tag 'pinctrl-v4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: cherryview: Add a quirk to make Acer Chromebook keyboard work again
pinctrl: samsung: Add missing part for PINCFG_TYPE_DRV of Exynos5433
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"i915, gvt, nouveau, udl and etnaviv fixes.
I was away the end of last week, so some of these would have been in
rc6, and it's Easter from tomorrow, so I decided I better dequeue what
I have now.
The nouveau changes, just add a hw enable for GP107 display (like a
pci id addition really), and fix a couple of regressions. i915 has
some more gvt fixes, along with a few run of the mill ones, the rcu
one seems like a few people have hit it.
Otherwise a small udl and small etnaviv fix"
* tag 'drm-fixes-for-v4.11-rc7' of git://people.freedesktop.org/~airlied/linux: (22 commits)
drm/etnaviv: fix missing unlock on error in etnaviv_gpu_submit()
drm/udl: Fix unaligned memory access in udl_render_hline
drm/i915: Don't call synchronize_rcu_expedited under struct_mutex
drm/i915: Suspend GuC prior to GPU Reset during GEM suspend
drm/nouveau: initial support (display-only) for GP107
drm/nouveau/kms/nv50: fix double dma_fence_put() when destroying plane state
drm/nouveau/kms/nv50: fix setting of HeadSetRasterVertBlankDmi method
drm/nouveau/mmu/nv4a: use nv04 mmu rather than the nv44 one
drm/nouveau/mpeg: mthd returns true on success now
drm/i915/gvt: set the correct default value of CTX STATUS PTR
drm/i915/gvt: Fix firmware loading interface for GVT-g golden HW state
drm/i915: Use a dummy timeline name for a signaled fence
drm/i915: Ironlake do_idle_maps w/a may be called w/o struct_mutex
drm/i915/gvt: remove the redundant info NULL check
drm/i915/gvt: adjust mem size for low resolution type
drm/i915: Avoid lock dropping between rescheduling
drm/i915/gvt: exclude cfg space from failsafe mode
drm/i915/gvt: Activate/de-activate vGPU in mdev ops.
drm/i915/execlists: Wrap tail pointer after reset tweaking
drm/i915/perf: remove user triggerable warn
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fixes from Thierry Reding:
"This contain a fix for the atomic update support recently added to
the Rockchip driver where the clock reference count would become
unbalanced and result in the clock feeding the PWM to always be
disabled.
Another fix to the Intel LPSS driver that adds an update bit quirk
required for a specific configuration"
* tag 'pwm/for-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: rockchip: State of PWM clock should synchronize with PWM enabled state
pwm: lpss: Set enable-bit before waiting for update-bit to go low
pwm: lpss: Split Tangier configuration
|
|
Commit 10c7e20b2ff3 (ACPI / scan: fix enumeration (visited) flags for
bus rescans) attempted to fix a problem with ACPI-based enumerateion
of I2C/SPI devices, but it forgot to ensure that the visited flag
will be set for all of the other enumerated devices, so fix that.
Fixes: 10c7e20b2ff3 (ACPI / scan: fix enumeration (visited) flags for bus rescans)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194885
Reported-and-tested-by: Kevin Locke <kevin@kevinlocke.name>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 4.8+ <stable@vger.kernel.org> # 4.8+
|
|
There is a report that after commit 27622b061eb4 ("cpufreq: Convert
to hotplug state machine"), the normal CPU offline/online cycle
fails on some platforms.
According to the ftrace result, this problem was triggered on
platforms using acpi-cpufreq as the default cpufreq driver,
and due to the lack of some ACPI freq method (eg. _PCT),
cpufreq_online() failed and returned a negative value, so the CPU
hotplug state machine rolled back the CPU online process. Actually,
from the user's perspective, the failure of cpufreq_online() should
not prevent that CPU from being brought up, although cpufreq might
not work on that CPU.
BTW, during system startup cpufreq_online() is not invoked via CPU
online but by the cpufreq device creation process, so the APs can be
brought up even though cpufreq_online() fails in that stage.
This patch ignores the return value of cpufreq_online/offline() and
lets the cpufreq framework deal with the failure. cpufreq_online()
itself will do a proper rollback in that case and if _PCT is missing,
the ACPI cpufreq driver will print a warning if the corresponding
debug options have been enabled.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=194581
Fixes: 27622b061eb4 ("cpufreq: Convert to hotplug state machine")
Reported-and-tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
GP107 modesetting support (just recognising the chipset, no other changes until 4.12)
a couple of regression fixes, one of them a rather serious double-free issue that appeared in 4.10.
* 'linux-4.11' of git://github.com/skeggsb/linux:
drm/nouveau: initial support (display-only) for GP107
drm/nouveau/kms/nv50: fix double dma_fence_put() when destroying plane state
drm/nouveau/kms/nv50: fix setting of HeadSetRasterVertBlankDmi method
drm/nouveau/mmu/nv4a: use nv04 mmu rather than the nv44 one
drm/nouveau/mpeg: mthd returns true on success now
|
|
git://anongit.freedesktop.org/git/drm-intel into drm-fixes
drm/i915 fixes for v4.11-rc7
one rcu related fix, and a few GVT fixes.
* tag 'drm-intel-fixes-2017-04-12' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Don't call synchronize_rcu_expedited under struct_mutex
drm/i915: Suspend GuC prior to GPU Reset during GEM suspend
drm/i915/gvt: set the correct default value of CTX STATUS PTR
drm/i915/gvt: Fix firmware loading interface for GVT-g golden HW state
drm/i915: Use a dummy timeline name for a signaled fence
drm/i915: Ironlake do_idle_maps w/a may be called w/o struct_mutex
drm/i915/gvt: remove the redundant info NULL check
drm/i915/gvt: adjust mem size for low resolution type
drm/i915: Avoid lock dropping between rescheduling
drm/i915/gvt: exclude cfg space from failsafe mode
drm/i915/gvt: Activate/de-activate vGPU in mdev ops.
drm/i915/execlists: Wrap tail pointer after reset tweaking
drm/i915/perf: remove user triggerable warn
drm/i915/perf: destroy stream on sample_flags mismatch
drm/i915: Align "unfenced" tiled access on gen2, early gen3
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-fixes
drm-misc-fixes for 2017-04-11
Core changes:
- None
Driver changes
- udl: Fix unaligned memory access on SPARC (Jonathan)
* tag 'drm-misc-fixes-2017-04-11' of git://anongit.freedesktop.org/git/drm-misc:
drm/udl: Fix unaligned memory access in udl_render_hline
|
|
into drm-fixes
Single etnaviv error path fix.
* 'etnaviv/fixes' of https://git.pengutronix.de/git/lst/linux:
drm/etnaviv: fix missing unlock on error in etnaviv_gpu_submit()
|
|
The following warning triggers with a new unit test that stresses the
device-dax interface.
===============================
[ ERR: suspicious RCU usage. ]
4.11.0-rc4+ #1049 Tainted: G O
-------------------------------
./include/linux/rcupdate.h:521 Illegal context switch in RCU read-side critical section!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 0
2 locks held by fio/9070:
#0: (&mm->mmap_sem){++++++}, at: [<ffffffff8d0739d7>] __do_page_fault+0x167/0x4f0
#1: (rcu_read_lock){......}, at: [<ffffffffc03fbd02>] dax_dev_huge_fault+0x32/0x620 [dax]
Call Trace:
dump_stack+0x86/0xc3
lockdep_rcu_suspicious+0xd7/0x110
___might_sleep+0xac/0x250
__might_sleep+0x4a/0x80
__alloc_pages_nodemask+0x23a/0x360
alloc_pages_current+0xa1/0x1f0
pte_alloc_one+0x17/0x80
__pte_alloc+0x1e/0x120
__get_locked_pte+0x1bf/0x1d0
insert_pfn.isra.70+0x3a/0x100
? lookup_memtype+0xa6/0xd0
vm_insert_mixed+0x64/0x90
dax_dev_huge_fault+0x520/0x620 [dax]
? dax_dev_huge_fault+0x32/0x620 [dax]
dax_dev_fault+0x10/0x20 [dax]
__do_fault+0x1e/0x140
__handle_mm_fault+0x9af/0x10d0
handle_mm_fault+0x16d/0x370
? handle_mm_fault+0x47/0x370
__do_page_fault+0x28c/0x4f0
trace_do_page_fault+0x58/0x2a0
do_async_page_fault+0x1a/0xa0
async_page_fault+0x28/0x30
Inserting a page table entry may trigger an allocation while we are
holding a read lock to keep the device instance alive for the duration
of the fault. Use srcu for this keep-alive protection.
Fixes: dee410792419 ("/dev/dax, core: file operations and dax-mmap")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Under CONFIG_STRICT_DEVMEM, reading System RAM through /dev/mem is
disallowed. However, on x86, the first 1MB was always allowed for BIOS
and similar things, regardless of it actually being System RAM. It was
possible for heap to end up getting allocated in low 1MB RAM, and then
read by things like x86info or dd, which would trip hardened usercopy:
usercopy: kernel memory exposure attempt detected from ffff880000090000 (dma-kmalloc-256) (4096 bytes)
This changes the x86 exception for the low 1MB by reading back zeros for
System RAM areas instead of blindly allowing them. More work is needed to
extend this to mmap, but currently mmap doesn't go through usercopy, so
hardened usercopy won't Oops the kernel.
Reported-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Tested-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Add the missing unlock before return from function etnaviv_gpu_submit()
in the error handling case.
lst: fixed label name.
Fixes: f3cd1b064f11 ("drm/etnaviv: (re-)protect fence allocation with
GPU mutex")
CC: stable@vger.kernel.org #4.9+
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
|
|
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"There has been work in a number of different areas over the last
weeks, including:
- Fix target-core-user (TCMU) back-end bi-directional handling (Xiubo
Li + Mike Christie + Ilias Tsitsimpis)
- Fix iscsi-target TMR reference leak during session shutdown (Rob
Millner + Chu Yuan Lin)
- Fix target_core_fabric_configfs.c race between LUN shutdown +
mapped LUN creation (James Shen)
- Fix target-core unknown fabric callback queue-full errors (Potnuri
Bharat Teja)
- Fix iscsi-target + iser-target queue-full handling in order to
support iw_cxgb4 RNICs. (Potnuri Bharat Teja + Sagi Grimberg)
- Fix ALUA transition state race between multiple initiator (Mike
Christie)
- Drop work-around for legacy GlobalSAN initiator, to allow QLogic
57840S + 579xx offload HBAs to work out-of-the-box in MSFT
environments. (Martin Svec + Arun Easi)
Note that a number are CC'ed for stable, and although the queue-full
bug-fixes required for iser-target to work with iw_cxgb4 aren't CC'ed
here, they'll be posted to Greg-KH separately"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
tcmu: Skip Data-Out blocks before gathering Data-In buffer for BIDI case
iscsi-target: Drop work-around for legacy GlobalSAN initiator
target: Fix ALUA transition state race between multiple initiators
iser-target: avoid posting a recv buffer twice
iser-target: Fix queue-full response handling
iscsi-target: Propigate queue_data_in + queue_status errors
target: Fix unknown fabric callback queue-full errors
tcmu: Fix wrongly calculating of the base_command_size
tcmu: Fix possible overwrite of t_data_sg's last iov[]
target: Avoid mappedlun symlink creation during lun shutdown
iscsi-target: Fix TMR reference leak during session shutdown
usb: gadget: Correct usb EP argument for BOT status request
tcmu: Allow cmd_time_out to be set to zero (disabled)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Two libata fixes.
One to disable hotplug on VT6420 which never worked properly. The
other reverts an earlier patch which disabled the second port on
SB600/700. There were some confusions due to earlier datasheets which
incorrectly indicated that the second port is not implemented on both
SB600 and 700"
* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
sata_via: Enable hotplug only on VT6421
Revert "pata_atiixp: Don't use unconnected secondary port on SB600/SB700"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- revert of a commit that switched all Synaptics touchpads over to be
driven by hid-rmi. It turns out that this caused several user-visible
regressions, and therefore we revert back to the original state
before all the reported issues have been fixed.
- a new uclogic device ID addition, from Xiaolei Yu.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
Revert "HID: rmi: Handle all Synaptics touchpads using hid-rmi"
HID: uclogic: add support for Ugee Tablet EX07S
|
|
On a dual controller setup with multipath enabled, some MEDIUM ERRORs
caused both paths to be failed, thus I/O got queued/blocked since the
'queue_if_no_path' feature is enabled by default on IPR controllers.
This example disabled 'queue_if_no_path' so the I/O failure is seen at
the sg_dd program. Notice that after the sg_dd test-case, both paths
are in 'failed' state, and both path/priority groups are in 'enabled'
state (not 'active') -- which would block I/O with 'queue_if_no_path'.
# sg_dd if=/dev/dm-2 bs=4096 count=1 dio=1 verbose=4 blk_sgio=0
<...>
read(unix): count=4096, res=-1
sg_dd: reading, skip=0 : Input/output error
<...>
# dmesg
[...] sd 2:2:16:0: [sds] FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[...] sd 2:2:16:0: [sds] Sense Key : Medium Error [current]
[...] sd 2:2:16:0: [sds] Add. Sense: Unrecovered read error - recommend rewrite the data
[...] sd 2:2:16:0: [sds] CDB: Read(10) 28 00 00 00 00 00 00 00 20 00
[...] blk_update_request: I/O error, dev sds, sector 0
[...] device-mapper: multipath: Failing path 65:32.
<...>
[...] device-mapper: multipath: Failing path 65:224.
# multipath -l
1IBM_IPR-0_59C2AE0000001F80 dm-2 IBM ,IPR-0 59C2AE00
size=5.2T features='0' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=0 status=enabled
| `- 2:2:16:0 sds 65:32 failed undef running
`-+- policy='service-time 0' prio=0 status=enabled
`- 1:2:7:0 sdae 65:224 failed undef running
This is not the desired behavior. The dm-multipath explicitly checks
for the MEDIUM ERROR case (and a few others) so not to fail the path
(e.g., I/O to other sectors could potentially happen without problems).
See dm-mpath.c :: do_end_io_bio() -> noretry_error() !->! fail_path().
The problem trace is:
1) ipr_scsi_done() // SENSE KEY/CHECK CONDITION detected, go to..
2) ipr_erp_start() // ipr_is_gscsi() and masked_ioasc OK, go to..
3) ipr_gen_sense() // masked_ioasc is IPR_IOASC_MED_DO_NOT_REALLOC,
// so set DID_PASSTHROUGH.
4) scsi_decide_disposition() // check for DID_PASSTHROUGH and return
// early on, faking a DID_OK.. *instead*
// of reaching scsi_check_sense().
// Had it reached the latter, that would
// set host_byte to DID_MEDIUM_ERROR.
5) scsi_finish_command()
6) scsi_io_completion()
7) __scsi_error_from_host_byte() // That would be converted to -ENODATA
<...>
8) dm_softirq_done()
9) multipath_end_io()
10) do_end_io()
11) noretry_error() // And that is checked in dm-mpath :: noretry_error()
// which would cause fail_path() not to be called.
With this patch applied, the I/O is failed but the paths are not. This
multipath device continues accepting more I/O requests without blocking.
(and notice the different host byte/driver byte handling per SCSI layer).
# dmesg
[...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
[...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 40 00
[...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
[...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
[...] blk_update_request: critical medium error, dev sdaf, sector 0
[...] blk_update_request: critical medium error, dev dm-6, sector 0
[...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
[...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 10 00
[...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
[...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
[...] blk_update_request: critical medium error, dev sdaf, sector 0
[...] blk_update_request: critical medium error, dev dm-6, sector 0
[...] Buffer I/O error on dev dm-6, logical block 0, async page read
# multipath -l 1IBM_IPR-0_59C2AE0000001F80
1IBM_IPR-0_59C2AE0000001F80 dm-6 IBM ,IPR-0 59C2AE00
size=5.2T features='1 queue_if_no_path' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=0 status=active
| `- 2:2:7:0 sdaf 65:240 active undef running
`-+- policy='service-time 0' prio=0 status=enabled
`- 1:2:7:0 sdh 8:112 active undef running
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During a PCI error recovery, if aac_check_health() is not aware that a
PCI error happened and we have an offline PCI channel, it might trigger
some errors (like NULL pointer dereference) and inhibit the error
recovery process to complete.
This patch makes the health check procedure aware of PCI channel issues,
and in case of error recovery process, the function
aac_adapter_check_health() returns -1 and let the recovery process to
complete successfully. This patch was tested on upstream kernel
v4.11-rc5 in PowerPC ppc64le architecture with adapter 9005:028d
(VID:DID) - the error recovery procedure was able to recover fine.
Fixes: 5c63f7f710bd ("aacraid: Added EEH support")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
On SPARC, the udl driver filled my kernel log with these messages:
[186668.910612] Kernel unaligned access at TPC[76609c] udl_render_hline+0x13c/0x3a0
Use put_unaligned_be16 to avoid them. On x86 this results in the same
code, but on SPARC the compiler emits two single-byte stores.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170407200229.20642-1-j.neuschaefer@gmx.net
|
|
Only call synchronize_rcu_expedited after unlocking struct_mutex to
avoid deadlock because the workqueues depend on struct_mutex.
>From original patch by Andrea:
synchronize_rcu/synchronize_sched/synchronize_rcu_expedited() will
hang until its own workqueues are run. The i915 gem workqueues will
wait on the struct_mutex to be released. So we cannot wait for a
quiescent state using those rcu primitives while holding the
struct_mutex or it creates a circular lock dependency resulting in
kernel hangs (which is reproducible but goes undetected by lockdep).
kswapd0 D 0 700 2 0x00000000
Call Trace:
? __schedule+0x1a5/0x660
? schedule+0x36/0x80
? _synchronize_rcu_expedited.constprop.65+0x2ef/0x300
? wake_up_bit+0x20/0x20
? rcu_stall_kick_kthreads.part.54+0xc0/0xc0
? rcu_exp_wait_wake+0x530/0x530
? i915_gem_shrink+0x34b/0x4b0
? i915_gem_shrinker_scan+0x7c/0x90
? i915_gem_shrinker_scan+0x7c/0x90
? shrink_slab.part.61.constprop.72+0x1c1/0x3a0
? shrink_zone+0x154/0x160
? kswapd+0x40a/0x720
? kthread+0xf4/0x130
? try_to_free_pages+0x450/0x450
? kthread_create_on_node+0x40/0x40
? ret_from_fork+0x23/0x30
plasmashell D 0 4657 4614 0x00000000
Call Trace:
? __schedule+0x1a5/0x660
? schedule+0x36/0x80
? schedule_preempt_disabled+0xe/0x10
? __mutex_lock.isra.4+0x1c9/0x790
? i915_gem_close_object+0x26/0xc0
? i915_gem_close_object+0x26/0xc0
? drm_gem_object_release_handle+0x48/0x90
? drm_gem_handle_delete+0x50/0x80
? drm_ioctl+0x1fa/0x420
? drm_gem_handle_create+0x40/0x40
? pipe_write+0x391/0x410
? __vfs_write+0xc6/0x120
? do_vfs_ioctl+0x8b/0x5d0
? SyS_ioctl+0x3b/0x70
? entry_SYSCALL_64_fastpath+0x13/0x94
kworker/0:0 D 0 29186 2 0x00000000
Workqueue: events __i915_gem_free_work
Call Trace:
? __schedule+0x1a5/0x660
? schedule+0x36/0x80
? schedule_preempt_disabled+0xe/0x10
? __mutex_lock.isra.4+0x1c9/0x790
? del_timer_sync+0x44/0x50
? update_curr+0x57/0x110
? __i915_gem_free_objects+0x31/0x300
? __i915_gem_free_objects+0x31/0x300
? __i915_gem_free_work+0x2d/0x40
? process_one_work+0x13a/0x3b0
? worker_thread+0x4a/0x460
? kthread+0xf4/0x130
? process_one_work+0x3b0/0x3b0
? kthread_create_on_node+0x40/0x40
? ret_from_fork+0x23/0x30
Fixes: 3d3d18f086cd ("drm/i915: Avoid rcu_barrier() from reclaim paths (shrinker)")
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 8f612d055183545070ca1009ac2eb1f2e044cc20)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
i915 is currently doing a full GPU reset at the end of
i915_gem_suspend() followed by GuC suspend in i915_drm_suspend(). This
GPU reset clobbers the GuC, causing the suspend request to then fail,
leaving the GuC in an undefined state. We need to tell the GuC to
suspend before we do the direct intel_gpu_reset().
v2: Commit message update. (Chris, Daniele)
Fixes: 1c777c5d1dcd ("drm/i915/hsw: Fix GPU hang during resume from S3-devices state")
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491387710-20553-1-git-send-email-sagar.a.kamble@intel.com
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit fd08923384385400101c71ac0d21d37d6b23b00d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
drm-intel-fixes
gvt-fixes-2017-04-07
- execlist csb initial read ptr fix (Min)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170407084240.4d2ig5ja2umcnsq3@zhen-hp.sh.intel.com
|
|
This reverts commit 279967a65b320d174a507498aea7d44db3fee7f4.
Multiple regressions [1] [2] [3] have been reported. The hid-rmi
support would have to fixed and redone in 4.11+.
[1] http://lkml.kernel.org/r/b79b88c8-770a-13f6-5668-c3a94254e5e0@gmail.com
[2] http://lkml.kernel.org/r/375e67b5-2cb8-3491-1d71-d8650d6e9451@gmail.com
[3] https://bugzilla.kernel.org/show_bug.cgi?id=195287
Reported-by: Cameron Gutman <aicommander@gmail.com>
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reported-by: Lorenzo J. Lucchini <ljlbox@tiscali.it>
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
After commit 47c950d10202 ("pinctrl: cherryview: Do not add all
southwest and north GPIOs to IRQ domain") the driver does not add all
GPIOs to the irqdomain. The reason for that is that those GPIOs cannot
generate IRQs at all, only GPEs (General Purpose Events). This causes
Linux virtual IRQ numbering to change.
However, it seems some CYAN Chromebooks, including Acer Chromebook
hardcodes these Linux IRQ numbers in the ACPI tables of the machine.
Since the numbering is different now, the IRQ meant for keyboard does
not match the Linux virtual IRQ number anymore making the keyboard
non-functional.
Work this around by adding special quirk just for these machines where
we add back all GPIOs to the irqdomain. Rest of the Cherryview/Braswell
based machines will not be affected by the change.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Fixes: 47c950d10202 ("pinctrl: cherryview: Do not add all southwest and north GPIOs to IRQ domain")
Reported-by: Adam S Levy <theadamlevy@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The following warning results from holding a lane spinlock,
preempt_disable(), or the btt map spinlock and then trying to take the
reconfig_mutex to walk the poison list and potentially add new entries.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:747
in_atomic(): 1, irqs_disabled(): 0, pid: 17159, name: dd
[..]
Call Trace:
dump_stack+0x85/0xc8
___might_sleep+0x184/0x250
__might_sleep+0x4a/0x90
__mutex_lock+0x58/0x9b0
? nvdimm_bus_lock+0x21/0x30 [libnvdimm]
? __nvdimm_bus_badblocks_clear+0x2f/0x60 [libnvdimm]
? acpi_nfit_forget_poison+0x79/0x80 [nfit]
? _raw_spin_unlock+0x27/0x40
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_forget_poison+0x25/0x50 [libnvdimm]
nvdimm_clear_poison+0x106/0x140 [libnvdimm]
nsio_rw_bytes+0x164/0x270 [libnvdimm]
btt_write_pg+0x1de/0x3e0 [nd_btt]
? blk_queue_enter+0x30/0x290
btt_make_request+0x11a/0x310 [nd_btt]
? blk_queue_enter+0xb7/0x290
? blk_queue_enter+0x30/0x290
generic_make_request+0x118/0x3b0
As a minimal fix, disable error clearing when the BTT is enabled for the
namespace. For the final fix a larger rework of the poison list locking
is needed.
Note that this is not a problem in the blk case since that path never
calls nvdimm_clear_poison().
Cc: <stable@vger.kernel.org>
Fixes: 82bf1037f2ca ("libnvdimm: check and clear poison before writing to pmem")
Cc: Dave Jiang <dave.jiang@intel.com>
[jeff: dynamically disable error clearing in the btt case]
Suggested-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Holding the reconfig_mutex over a potential userspace fault sets up a
lockdep dependency chain between filesystem-DAX and the libnvdimm ioctl
path. Move the user access outside of the lock.
[ INFO: possible circular locking dependency detected ]
4.11.0-rc3+ #13 Tainted: G W O
-------------------------------------------------------
fallocate/16656 is trying to acquire lock:
(&nvdimm_bus->reconfig_mutex){+.+.+.}, at: [<ffffffffa00080b1>] nvdimm_bus_lock+0x21/0x30 [libnvdimm]
but task is already holding lock:
(jbd2_handle){++++..}, at: [<ffffffff813b4944>] start_this_handle+0x104/0x460
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (jbd2_handle){++++..}:
lock_acquire+0xbd/0x200
start_this_handle+0x16a/0x460
jbd2__journal_start+0xe9/0x2d0
__ext4_journal_start_sb+0x89/0x1c0
ext4_dirty_inode+0x32/0x70
__mark_inode_dirty+0x235/0x670
generic_update_time+0x87/0xd0
touch_atime+0xa9/0xd0
ext4_file_mmap+0x90/0xb0
mmap_region+0x370/0x5b0
do_mmap+0x415/0x4f0
vm_mmap_pgoff+0xd7/0x120
SyS_mmap_pgoff+0x1c5/0x290
SyS_mmap+0x22/0x30
entry_SYSCALL_64_fastpath+0x1f/0xc2
-> #1 (&mm->mmap_sem){++++++}:
lock_acquire+0xbd/0x200
__might_fault+0x70/0xa0
__nd_ioctl+0x683/0x720 [libnvdimm]
nvdimm_ioctl+0x8b/0xe0 [libnvdimm]
do_vfs_ioctl+0xa8/0x740
SyS_ioctl+0x79/0x90
do_syscall_64+0x6c/0x200
return_from_SYSCALL_64+0x0/0x7a
-> #0 (&nvdimm_bus->reconfig_mutex){+.+.+.}:
__lock_acquire+0x16b6/0x1730
lock_acquire+0xbd/0x200
__mutex_lock+0x88/0x9b0
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_forget_poison+0x25/0x50 [libnvdimm]
nvdimm_clear_poison+0x106/0x140 [libnvdimm]
pmem_do_bvec+0x1c2/0x2b0 [nd_pmem]
pmem_make_request+0xf9/0x270 [nd_pmem]
generic_make_request+0x118/0x3b0
submit_bio+0x75/0x150
Cc: <stable@vger.kernel.org>
Fixes: 62232e45f4a2 ("libnvdimm: control (ioctl) messages for nvdimm_bus and nvdimm devices")
Cc: Dave Jiang <dave.jiang@intel.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Commit 57e5568fda27 ("sata_via: Implement hotplug for VT6421") adds
hotplug IRQ handler for VT6421 but enables hotplug on all chips. This
is a bug because it causes "irq xx: nobody cared" error on VT6420 when
hot-(un)plugging a drive:
[ 381.839948] irq 20: nobody cared (try booting with the "irqpoll" option)
[ 381.840014] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-rc5+ #148
[ 381.840066] Hardware name: P4VM800/P4VM800, BIOS P1.60 05/29/2006
[ 381.840117] Call Trace:
[ 381.840167] <IRQ>
[ 381.840225] ? dump_stack+0x44/0x58
[ 381.840278] ? __report_bad_irq+0x14/0x97
[ 381.840327] ? handle_edge_irq+0xa5/0xa5
[ 381.840376] ? note_interrupt+0x155/0x1cf
[ 381.840426] ? handle_edge_irq+0xa5/0xa5
[ 381.840474] ? handle_irq_event_percpu+0x32/0x38
[ 381.840524] ? handle_irq_event+0x1f/0x38
[ 381.840573] ? handle_fasteoi_irq+0x69/0xb8
[ 381.840625] ? handle_irq+0x4f/0x5d
[ 381.840672] </IRQ>
[ 381.840726] ? do_IRQ+0x2e/0x8b
[ 381.840782] ? common_interrupt+0x2c/0x34
[ 381.840836] ? mwait_idle+0x60/0x82
[ 381.840892] ? arch_cpu_idle+0x6/0x7
[ 381.840949] ? do_idle+0x96/0x18e
[ 381.841002] ? cpu_startup_entry+0x16/0x1a
[ 381.841057] ? start_kernel+0x319/0x31c
[ 381.841111] ? startup_32_smp+0x166/0x168
[ 381.841165] handlers:
[ 381.841219] [<c12a7263>] ata_bmdma_interrupt
[ 381.841274] Disabling IRQ #20
Seems that VT6420 can do hotplug too (there's no documentation) but the
comments say that SCR register access (required for detecting hotplug
events) can cause problems on these chips.
For now, just keep hotplug disabled on anything other than VT6421.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
