| Age | Commit message (Collapse) | Author |
|---|
|
This should be RFD77402, not RFD77420.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
IIO_ST_SENSORS_CORE select IIO_ST_SENSORS_I2C
unconditionally, if REGMAP_I2C is not set, build fails
drivers/iio/common/st_sensors/st_sensors_i2c.o: In function `st_sensors_i2c_configure':
st_sensors_i2c.c:(.text+0x58): undefined reference to `__devm_regmap_init_i2c'
This patch selects REGMAP_I2C to fix it.
IIO_ST_SENSORS_SPI is similar to SPI issue.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 062809ef7733 ("iio: make st_sensors drivers use regmap")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The AD7606B is a 16-bit ADC that supports simultaneous sampling of 8
channels. It is pin compatible to AD7606, but adds extra modes by
writing to the register map.
The AD7606B can be configured to work in software mode by setting all
oversampling pins to high. This mode is selected by default.
The oversampling ratio is configured from the OS_MODE register (address
0x08) with the addition of OS=128 and OS=256 that were not available in
hardware mode.
The device is configured to output data on a single spi channel, but this
configuration must be done right after restart. That is why the delay was
removed for devices which doesn't require it.
Moreover, in software mode, the range gpio has no longer its function.
Instead, the scale can be configured individually for each channel from
the RANGE_CH registers (address 0x03 to 0x06). Besides the already
supported ±10 V and ±5 V ranges, software mode can also accommodate the
±2.5 V range.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Co-developed-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
On Spreadtrum platform, the headphone will read one ADC channel multiple
times to identify the headphone type, and the headphone identification is
sensitive of the ADC reading time. And we found it will take longer time
to reading ADC data by using interrupt mode comparing with the polling
mode, thus we should change to polling mode to improve the efficiency
of reading data, which can identify the headphone type successfully.
Signed-off-by: Freeman Liu <freeman.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Instead of linear approach to calculate power of 10, use generic int_pow()
which does it better.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use device-managed APIs to simplify the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Replace shift and minus operation by GENMASK macro and remove the local
variables used to store intermediate data.
Signed-off-by: Rodrigo Ribeiro Carvalho <rodrigorsdc@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
By adding this option we are able to remove the sync3 field and dt binding.
When setting the required cutoff frequency we also determine the ADC
configuration for chop and sync filter.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch removes the reference voltage entry from the platform_data
structure. This is no longer needed since the reference voltage is obtained
from the device tree. With this we also remove the entire ad7192.h file.
The undefined reference voltage warning is promoted to an error signaling a
problem with the device tree.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Caught via static-analysis checker:
```
drivers/iio/imu/adis16460.c
152 static int adis16460_set_freq(struct iio_dev *indio_dev, int val, int val2)
153 {
154 struct adis16460 *st = iio_priv(indio_dev);
155 unsigned int t;
^^^^^^^^^^^^^^
156
157 t = val * 1000 + val2 / 1000;
158 if (t <= 0)
^^^^^^
Unsigned is not less than zero.
```
The types of `val` && `val2` are obtained from the IIO `write_raw` hook, so
userspace can provide negative values, which can cause weird behavior after
conversion to unsigned.
This patch changes the sign of variable `t` so that -EINVAL will be
returned for negative values as well.
Fixes: db6ed4d23dd1 ("iio: imu: Add support for the ADIS16460 IMU")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The KIOX010A and KIOX020A ACPI ids go hand in hand, they are used in
yoga style 2-in-1s, with KIOX010A indicating the KXCJ91008 sensor in the
display of the 2-in-1 and KIOX020A indicating the KXCJ91008 sensor in the
base.
Improve the existing comment on the "KIOX010A" kx_acpi_match table entry
to make clear we are talking about a yoga-style (360 degree hinges) device
here and add a similar comment to the "KIOX020A" entry.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
There is some "confusing" license text in some of the sm750fb driver
files. After discussing it with the company, it turns out to have been
a mistake and these lines can be safely removed. The files are all to
be licensed under the GPLv2 license.
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: linux-fbdev@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190815123009.16499-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As Chao pointed out [1], ENOTSUPP is used for NFS
protocol only, we should use EOPNOTSUPP instead...
[1] https://lore.kernel.org/lkml/108ee2f9-75dd-b8ab-8da7-b81c17bafbf6@huawei.com/
Reported-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Link: https://lore.kernel.org/r/20190814103705.60698-3-gaoxiang25@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For some specific fields, use EOPNOTSUPP instead of EIO
for values which look sane but aren't supported right now.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Link: https://lore.kernel.org/r/20190814103705.60698-2-gaoxiang25@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Previously, EROFS uses EIO to indicate that filesystem
is corrupted as well. However, as Pavel said [1], other
filesystems tend to use EUCLEAN(EFSCORRUPTED) instead,
let's follow what others do right now.
Also, add some more prints to the syslog.
[1] https://lore.kernel.org/lkml/20190813114821.GB11559@amd/
Suggested-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Link: https://lore.kernel.org/r/20190814103705.60698-1-gaoxiang25@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Variable fx2delay is being initialized with a value that is never read
and fx2delay is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190815105314.5756-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a statement that is indented one level too deeply, remove
the extraneous tab.
Addresses-Coverity: ("Identation does not match nesting level")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190815084034.13885-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Static structure apex_desc, of type gasket_driver_desc, is used only as
an argument to the functions gasket_register_device() and
gasket_unregister_device(). In the definitions of both these functions,
their parameter is declared as const. Hence make apex_desc itself
constant to protect it from modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190815054924.643-1-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
in fill_inode() we call iloc() twice.Avoiding the extra call by
storing the result.
Signed-off-by: Pratik Shinde <pratikshinde320@gmail.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Cc: Gao Xiang <gaoxiang25@huawei.com>
Link: https://lore.kernel.org/r/20190813203840.13782-1-pratikshinde320@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Link settings can be changed only when the interface is down. Disable
and re-enable the interface, if necessary, behind the scenes so that we do
not force users to an if down/up sequence.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-11-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The register_netdev() call should be made only when ready to process any
user request on the interface. Move the call to be the last one issued
in the probe sequence.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-10-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the current state, the dpaa2-ethsw driver supports only one bridge
per DPSW object. Reword the error message so that this information is
much more clear.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-9-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ethsw_add_vlan() function is already called only when the VLAN is
not yet configured on the switch. Remove the redundant check.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-8-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ethtool core already zeroes the memory before calling
.get_ethtool_stats() thus making the memset unnecessary. Remove it.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-7-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use a bool instead of an u8 in ethsw_set_learning() and
ethsw_port_set_flood() to encode an binary type property.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-6-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since ethtool will be loud enough if the .set_link_ksettings() callback
fails, remove the debug messages which do not add additional
information.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-5-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the '\n' line terminator to the string formats missing it.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-4-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
At probe time, only the DPSW object should be enabled without the
associated ports, which will get enabled on dev_open. Remove the
ethsw_open() and ethsw_stop() functions and replace them only with
dpsw_enable()/_disable().
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-3-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Do not add an IGMP multicast address by default since we do not support
Rx/Tx ar the moment.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-2-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Variable ret is initialized to a value that is never read and it is
re-assigned later. The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190813124838.1317-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the checkpatch.pl script was run, it showed lines with length
more than 80 characters in rtl8712_recv.c file. Fixed by
breaking it up into two lines within 80 characters.
Signed-off-by: Merwin Trever Ferrao <merwintf@gmail.com>
Link: https://lore.kernel.org/r/20190813065806.GA23606@IoT-COE
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change return type of r8712_dump_aggr_xframe from u8 to void as it
always returns _SUCCESS and its return value is never used.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190813044638.16348-4-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change return type of r8712_xmitframe_aggr_1st from u8 to void as it
always returns _SUCCESS and its return value is never used.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190813044638.16348-3-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change return type of r8712_append_mpdu_unit from u8 to void and remove
its return statement as it always returns only _SUCCESS. Modify call
sites to simply call this function instead of checking its return value,
and execute all the statements in the if-block for when the function
returns _SUCCESS.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190813044638.16348-2-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change return values of xmitframe_addmic from _SUCCESS and _FAIL to 0
and -ENOMEM respectively. Modify call sites to check for non-zero values
instead of _FAIL.
Also change return type from sint to int.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190813044638.16348-1-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The procfs provides many useful information for debugging, but it may be
too much for normal usage, routines like proc_get_sec_info() reports
various security related information.
So let's remove it.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20190813042426.13733-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Kill all the remaining BUG_ON in EROFS:
- one BUG_ON was used to detect xattr on-disk corruption,
proper error handling should be added for it instead;
- the other BUG_ONs are used to detect potential issues,
use DBG_BUGON only in (eng) debugging version.
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Link: https://lore.kernel.org/r/20190813023054.73126-3-gaoxiang25@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cleancache was not fully implemented in EROFS.
In addition, it's tend to remove the whole cleancache in
related attempt [1].
[1] https://lore.kernel.org/linux-fsdevel/20190527103207.13287-3-jgross@suse.com/
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Link: https://lore.kernel.org/r/20190813023054.73126-2-gaoxiang25@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As a helper in erofs_fs.h, erofs_inode_is_data_compressed()
should be inlined.
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Link: https://lore.kernel.org/r/20190813023054.73126-1-gaoxiang25@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This got caught by the implicit fall through detection but is
a bug rather than missing marking.
Reported-by: 0-DAY kernel test infrastructure
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 741172d18e8a ("iio: light: noa1305: Add support for NOA1305")
Link: https://lore.kernel.org/r/20190813133851.14345-1-Jonathan.Cameron@huawei.com
Cc: Gustavo Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.4 cycle
Note includes a merge from i3c tree to get support needed for stm_lsm6dsx driver
support for l3c devices. Done from immutable branch.
A counter subsystem patche in here as well.
Alongside the new device support (which is always good), Chuhong's work
on using devres managed APIs has cleaned up a number of drivers.
New device support
* adis16460
- New driver based on ADIS framework which needed addition of support
for cs_change_delay. Includes device tree binding.
* cros_ec
- Support fo the veyron-minnie which uses an older interface.
* lsm6dsx
- Support for LSM6DSTR-C gyro + magnetometer sensor (new IDs mainly)
- Support for ISM330DHCX acc + gyro sensor (extensive rework needed!)
* Maxim 5432
- New driver support MAX5432-MAX5435 family of potentiometers.
* noa1305
- New driver for this ON Semiconductor Ambient light sensor.
Features and cleanups
* tree wide
- Drop error prints after platform_get_irq as already prints errors
internally if any occur.
* docs
- Document mounting matrix.
- Fix a missing newline at end of file.
* ad2s1210
- Switch to device managed APIs for all of probe and drop explicit remove.
* ad7192
- Add of_device_id array to explicity handling DT bindings.
* ad7606
- Lots of rework leading to support for software configure modes in ad7616
parts.
- Debugfs register access support.
* am2315
- Switch to device managed APIs for all of probe and drop explicit remove.
* apds9960
- Typo in module description.
* cm36651
- Convert to i2c_new_dummy_device.
- Swithc to device managed APIs for all of probe adn drop explicit remove.
* cros_ec
- Calibscale support for accel, gyro and magnetometer.
- Tidy up some error codes to return the error from the stack rather than
-EIO.
- Determine protocol version.
- Add a sign vector to the core to fix sensor rotation if necessary.
Cannot just be done with mount matrix as already in use in many devices.
- Tidy up INFO_SCALE being in both the separate and shared lists.
- Drop a lot of dplicate code from the cros-ec-accel-legacy driver
and use the core provided code instead.
- Make frequency range available to userspace.
* counter / ftm-quaddec
- Switch to device managed APIs for all of probe adn drop explicit remove.
* hdc100x
- Switch to device managed APIs for all of probe and drop explicit remove.
* hi8435
- Use gpiod_set_value_cansleep as we don't care here and there is a
board out there where it needs to sleep.
- Switch to device managed APIs for all of probe and drop explict remove.
* hp03
- Convert to i2c_new_dummy_device.
* maxim thermocouple
- Switch to device managed APIs for all of probe and drop explicit remove.
* mmc35240
- Fix typo in constant naming.
* mpu6050
- Use devm_add_action_or_reset in place of explicit error handling.
- Make text in Kconfig more explicit about which parts are supported.
* mxc4005
- Switch to device managed APIs for all of probe and drop explicit remove.
* pms7003
- Convert device tree bindings to yaml.
- Add a MAINTAINERS entry
* sc27xx
- Introduce a local struct device *dev pointer to avoid lots of deref.
- Use devm_add_action_or_reset in place of explicit error handling.
* sca3000
- Typo fix in naming.
* si1145
- Switch to device managed APIs for all of probe and drop explicit remove.
* st_sensors
- Lots of rework to enable switch to regmap.
- Regmap conversion at the end.
- Tidy up some inconsistencies in buffer setup ops.
- Tidy up an oddity by dropping get_irq_data_ready function in favour
of direct access.
- Stop allocating buffer in buffer enable in favour of just embedding
a large enough constant size buffer in the iio_priv accessed structure.
* st_lsm6dsx
- l3c device support (LSM6DSO and LSM6DSR)
- tidy up irq return logic which was strangely written.
- fix up an ABI quirk where this driver used separate scale
attributes, even though they were always shared by type.
* stk33xx
- Device tree bindings include manufacturer ID.
* stm32-adc
- Add control for supply to analog switches including DT bindings.
* stm32 timer
- Drop the quadrature mode support. Believed there were no users so
take this opportunity to drop this unwanted ABI.
* tsl2772
- Switch to device mangage APIs for all of probe and drop explicit remove.
- Use regulator_bulk_* APIs to reduce repitition.
* veml6070
- Convert to i2c_new_dummy_device.
* tag 'iio-for-5.4a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (84 commits)
iio: hi8435: Drop hi8435_remove() by using devres for remaining elements
iio: hi8435: Use gpiod_set_value_cansleep()
iio:st_sensors: remove buffer allocation at each buffer enable
iio: imu: inv_mpu6050: be more explicit on supported chips
iio: light: noa1305: Add support for NOA1305
dt-bindings: Add binding document for NOA1305
iio: remove get_irq_data_ready() function pointer and use IRQ number directly
iio: imu: st_lsm6dsx: make IIO_CHAN_INFO_SCALE shared by type
iio: tsl2772: Use regulator_bulk_() APIs
iio: tsl2772: Use devm_iio_device_register
iio: tsl2772: Use devm_add_action_or_reset for tsl2772_chip_off
iio: tsl2772: Use devm_add_action_or_reset
iio: Remove dev_err() usage after platform_get_irq()
iio: light: si1145: Use device-managed APIs
iio:pressure: preenable/postenable/predisable fixup for ST press buffer
iio:magn: preenable/postenable/predisable fixup for ST magn buffer
iio:gyro: preenable/postenable/predisable fixup for ST gyro buffer
iio:accel: preenable/postenable/predisable fixup for ST accel buffer
dt-bindings: iio: imu: st_lsm6dsx: add ism330dhcx device bindings
iio: imu: st_lsm6dsx: add support to ISM330DHCX
...
|
|
Used checkpatch's --fix-inplace option for types SPACING, OPEN_BRACE,
ELSE_AFTER_BRACE. Manually edited the resulting changes to correct for
mistaken fixes and complete fixes that were only partially applied.
Signed-off-by: Stephen Brennan <stephen@brennan.io>
Link: https://lore.kernel.org/r/20190811225120.7308-1-stephen@brennan.io
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change return type of r8712_construct_txaggr_cmd_hdr from u8 to void as
it always returns _SUCCESS and its return value is never used.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190809052353.5308-8-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change return type of r8712_construct_txaggr_cmd_desc from u8 to void
(and remove its return statement) as it always returns _SUCCESS and its
return value is never stored, checked or otherwise used.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190809052353.5308-7-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change return type of r8712_xmit_direct from int to void as its return
value is never used. Remove return statement accordingly.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190809052353.5308-6-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change return type of r8712_free_xmitbuf from int to void (and remove
its return values) as its return value is never used.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190809052353.5308-5-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change return values of make_wlanhdr from _SUCCESS/_FAIL to 0/-EINVAL.
Modify call site to check for non-zero return values instead of _FAIL.
Change return type from sint to int.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190809052353.5308-4-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change return values of r8712_update_attrib from _SUCCESS and _FAIL to 0
and -ENOMEM or -EINVAL respectively. Modify call site to check for the
new failure conditions. Also modify the return type from sint to int.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190809052353.5308-2-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change the return values in _r8712_init_xmit_priv from _SUCCESS/_FAIL to
0/-ENOMEM respectively. Change return type from sint to int.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190809052353.5308-1-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
return -EIO for bus failures, 0 otherwise.
Signed-off-by: Adham Abozaeid <adham.abozaeid@microchip.com>
Link: https://lore.kernel.org/r/20190809182510.22443-3-adham.abozaeid@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
