| Age | Commit message (Collapse) | Author |
|---|
|
DSPI instances in Vybrid have a different amount of chip selects
and CTARs (Clock and transfer Attributes Register). In case of
DSPI1 we only have 2 CTAR registers and 4 CS. In present driver
implementation CTAR offset is derived from CS instance which will
lead to out of bound access if chip select instance is greater than
CTAR register instance, hence use single CTAR0 register for all CS
instances. Since we write the CTAR register anyway before each access,
there is no value in using the additional CTAR registers. Also one
should not program a value in CTAS for a CTAR register that is not
present, hence configure CTAS to use CTAR0.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- opal-irqchip: Fix double endian conversion from Alistair Popple
- cxl: Set endianess of kernel contexts from Frederic Barrat
- sbc8641: drop bogus PHY IRQ entries from DTS file from Paul Gortmaker
- Revert "powerpc/eeh: Don't unfreeze PHB PE after reset" from Andrew
Donnellan
* tag 'powerpc-4.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
Revert "powerpc/eeh: Don't unfreeze PHB PE after reset"
powerpc/sbc8641: drop bogus PHY IRQ entries from DTS file
cxl: Set endianess of kernel contexts
powerpc/opal-irqchip: Fix double endian conversion
|
|
Merge misc fixes from Andrew Morton:
"17 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MIPS: fix DMA contiguous allocation
sh64: fix __NR_fgetxattr
ocfs2: fix SGID not inherited issue
mm/oom_kill.c: avoid attempting to kill init sharing same memory
drivers/base/memory.c: prohibit offlining of memory blocks with missing sections
tmpfs: fix shmem_evict_inode() warnings on i_blocks
mm/hugetlb.c: fix resv map memory leak for placeholder entries
mm: hugetlb: call huge_pte_alloc() only if ptep is null
kernel: remove stop_machine() Kconfig dependency
mm: kmemleak: mark kmemleak_init prototype as __init
mm: fix kerneldoc on mem_cgroup_replace_page
osd fs: __r4w_get_page rely on PageUptodate for uptodate
MAINTAINERS: make Vladimir co-maintainer of the memory controller
mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress
mm: fix swapped Movable and Reclaimable in /proc/pagetypeinfo
memcg: fix memory.high target
mm: hugetlb: fix hugepage memory leak caused by wrong reserve count
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Fix the boot crash on Mako machines with Huge Pages, prevent a panic
with SATA controllers (and others) by correctly calculating the IOMMU
space, hook up the mlock2 syscall and drop unneeded code in the parisc
pci code"
* 'parisc-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Disable huge pages on Mako machines
parisc: Wire up mlock2 syscall
parisc: Remove unused pcibios_init_bus()
parisc iommu: fix panic due to trying to allocate too large region
|
|
Pull block layer fixes from Jens Axboe:
"A set of fixes for the current series. This contains:
- A bunch of fixes for lightnvm, should be the last round for this
series. From Matias and Wenwei.
- A writeback detach inode fix from Ilya, also marked for stable.
- A block (though it says SCSI) fix for an OOPS in SCSI runtime power
management.
- Module init error path fixes for null_blk from Minfei"
* 'for-linus' of git://git.kernel.dk/linux-block:
null_blk: Fix error path in module initialization
lightnvm: do not compile in debugging by default
lightnvm: prevent gennvm module unload on use
lightnvm: fix media mgr registration
lightnvm: replace req queue with nvmdev for lld
lightnvm: comments on constants
lightnvm: check mm before use
lightnvm: refactor spin_unlock in gennvm_get_blk
lightnvm: put blks when luns configure failed
lightnvm: use flags in rrpc_get_blk
block: detach bdev inode from its wb in __blkdev_put()
SCSI: Fix NULL pointer dereference in runtime PM
|
|
Commit bdee237c0343 ("x86: mm: Use 2GB memory block size on large-memory
x86-64 systems") and 982792c782ef ("x86, mm: probe memory block size for
generic x86 64bit") introduced large block sizes for x86. This made it
possible to have multiple sections per memory block where previously,
there was a only every one section per block.
Since blocks consist of contiguous ranges of section, there can be holes
in the blocks where sections are not present. If one attempts to
offline such a block, a crash occurs since the code is not designed to
deal with this.
This patch is a quick fix to gaurd against the crash by not allowing
blocks with non-present sections to be offlined.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=107781
Signed-off-by: Seth Jennings <sjennings@variantweb.net>
Reported-by: Andrew Banman <abanman@sgi.com>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On an hardware shared I2C bus (certain Intel Baytrail SoC platforms) the
runtime PM disable depth keeps increasing over repeated modprobe/rmmod
cycle because pm_runtime_disable() is called without checking should it
be disabled already because of bus sharing.
This hasn't made any other harm than dev->power.disable_depth keeps
increasing but keep it sync by calling pm_runtime_disable() only when
runtime PM is not disabled.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Because of some hardware limitation, AMD I2C controller can't
trigger pending interrupt if interrupt status has been changed
after clearing interrupt status bits. Then, I2C will lost
interrupt and IO timeout.
According to hardware design, this patch implements a workaround
to disable i2c controller interrupt and re-enable i2c interrupt
before exiting ISR.
To reduce the performance impacts on other vendors, use unlikely
function to check flag in ISR.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
When using the Promise TX2+ SATA controller on PA-RISC, the system often
crashes with kernel panic, for example just writing data with the dd
utility will make it crash.
Kernel panic - not syncing: drivers/parisc/sba_iommu.c: I/O MMU @ 000000000000a000 is out of mapping resources
CPU: 0 PID: 18442 Comm: mkspadfs Not tainted 4.4.0-rc2 #2
Backtrace:
[<000000004021497c>] show_stack+0x14/0x20
[<0000000040410bf0>] dump_stack+0x88/0x100
[<000000004023978c>] panic+0x124/0x360
[<0000000040452c18>] sba_alloc_range+0x698/0x6a0
[<0000000040453150>] sba_map_sg+0x260/0x5b8
[<000000000c18dbb4>] ata_qc_issue+0x264/0x4a8 [libata]
[<000000000c19535c>] ata_scsi_translate+0xe4/0x220 [libata]
[<000000000c19a93c>] ata_scsi_queuecmd+0xbc/0x320 [libata]
[<0000000040499bbc>] scsi_dispatch_cmd+0xfc/0x130
[<000000004049da34>] scsi_request_fn+0x6e4/0x970
[<00000000403e95a8>] __blk_run_queue+0x40/0x60
[<00000000403e9d8c>] blk_run_queue+0x3c/0x68
[<000000004049a534>] scsi_run_queue+0x2a4/0x360
[<000000004049be68>] scsi_end_request+0x1a8/0x238
[<000000004049de84>] scsi_io_completion+0xfc/0x688
[<0000000040493c74>] scsi_finish_command+0x17c/0x1d0
The cause of the crash is not exhaustion of the IOMMU space, there is
plenty of free pages. The function sba_alloc_range is called with size
0x11000, thus the pages_needed variable is 0x11. The function
sba_search_bitmap is called with bits_wanted 0x11 and boundary size is
0x10 (because dma_get_seg_boundary(dev) returns 0xffff).
The function sba_search_bitmap attempts to allocate 17 pages that must not
cross 16-page boundary - it can't satisfy this requirement
(iommu_is_span_boundary always returns true) and fails even if there are
many free entries in the IOMMU space.
How did it happen that we try to allocate 17 pages that don't cross
16-page boundary? The cause is in the function iommu_coalesce_chunks. This
function tries to coalesce adjacent entries in the scatterlist. The
function does several checks if it may coalesce one entry with the next,
one of those checks is this:
if (startsg->length + dma_len > max_seg_size)
break;
When it finishes coalescing adjacent entries, it allocates the mapping:
sg_dma_len(contig_sg) = dma_len;
dma_len = ALIGN(dma_len + dma_offset, IOVP_SIZE);
sg_dma_address(contig_sg) =
PIDE_FLAG
| (iommu_alloc_range(ioc, dev, dma_len) << IOVP_SHIFT)
| dma_offset;
It is possible that (startsg->length + dma_len > max_seg_size) is false
(we are just near the 0x10000 max_seg_size boundary), so the funcion
decides to coalesce this entry with the next entry. When the coalescing
succeeds, the function performs
dma_len = ALIGN(dma_len + dma_offset, IOVP_SIZE);
And now, because of non-zero dma_offset, dma_len is greater than 0x10000.
iommu_alloc_range (a pointer to sba_alloc_range) is called and it attempts
to allocate 17 pages for a device that must not cross 16-page boundary.
To fix the bug, we must make sure that dma_len after addition of
dma_offset and alignment doesn't cross the segment boundary. I.e. change
if (startsg->length + dma_len > max_seg_size)
break;
to
if (ALIGN(dma_len + dma_offset + startsg->length, IOVP_SIZE) > max_seg_size)
break;
This patch makes this change (it precalculates max_seg_boundary at the
beginning of the function iommu_coalesce_chunks). I also added a check
that the mapping length doesn't exceed dma_get_seg_boundary(dev) (it is
not needed for Promise TX2+ SATA, but it may be needed for other devices
that have dma_get_seg_boundary lower than dma_get_max_seg_size).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Without this, filter insertion on a VF would fail if only one channel
was in use. This would include the unicast station filter and therefore
no traffic would be received.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reset logic calls bnxt_close_nic() and bnxt_open_nic() under rtnl_lock
from bnxt_sp_task. BNXT_STATE_IN_SP_TASK must be cleared before calling
bnxt_close_nic() to avoid deadlock.
v2: Fixed white space error. Thanks Dave.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When implementing driver reset from tx_timeout in the next patch,
bnxt_close_nic() will be called from the sp_task workqueue. Calling
cancel_work() on sp_task will hang the workqueue.
Instead, set a new bit BNXT_STATE_IN_SP_TASK when bnxt_sp_task() is running.
bnxt_close_nic() will wait for BNXT_STATE_IN_SP_TASK to clear before
proceeding.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows multiple independent bits to be set for various states.
Subsequent patches to implement tx timeout reset will require this.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The declaration of the bitmap vf_req_snif_bmap using fixed array of
unsigned long will only work on 64-bit archs. Use DECLARE_BITMAP instead
which will work on all archs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 8b63ec1837fa ("phylib: Make PHYs children of their MDIO bus,
not the bus' parent.") changed the parenting of PHY devices, making
them a child of the MDIO bus, instead of the MAC device. This broken
the Micrel PHY driver which has a deprecated feature of allowing PHY
properties to be placed into the MAC node.
In order to find the MAC node, we need to walk up the tree of devices
until we find one with an OF node attached.
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Suggested-by: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Fixes: 8b63ec1837fa ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Intel RAPL initialized on several systems where the BIOS lock bit (msr
0x610, bit 63) was set. This occured because the return value of
rapl_read_data_raw() was being checked, rather than the value of the variable
passed in, locked.
This patch properly implments the rapl_read_data_raw() call to check the
variable locked, and now the Intel RAPL driver outputs the warning:
intel_rapl: RAPL package 0 domain package locked by BIOS
and does not initialize for the package.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
785ee27 ("cpufreq: intel_pstate: Fix limits->max_perf rounding error")
hardcodes the value of FRAC_BITS. This patch fixes that minor issue.
Fixes: 785ee2788141 (cpufreq: intel_pstate: Fix limits->max_perf rounding error)
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This driver is the only one that calls regulator_sync_voltage(), but it
can currently be built with CONFIG_REGULATOR disabled, producing
this build error:
drivers/cpufreq/tegra124-cpufreq.c: In function 'tegra124_cpu_switch_to_pllx':
drivers/cpufreq/tegra124-cpufreq.c:68:2: error: implicit declaration of function 'regulator_sync_voltage' [-Werror=implicit-function-declaration]
regulator_sync_voltage(priv->vdd_cpu_reg);
My first attempt was to implement a helper for this function
for regulator_sync_voltage, but Mark Brown explained:
We don't do this for *all* regulator API functions - there's some where
using them strongly suggests that there is actually a dependency on
the regulator API. This does seem like it might be falling into the
specialist category [...]
Looking at the code I'm pretty unclear on what the authors think the
use of _sync_voltage() is doing in the first place so it may be even
better to just remove the call. It seems to have been included in the
first commit so there's not changelog explaining things and there's
no comment either. I'd *expect* it to be a noop as far as I can see.
This adds the dependency to make the driver always build successfully
or not be enabled at all. Alternatively, we could investigate if the
driver should stop calling regulator_sync_voltage instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 4.4, 2nd round" from Shawn Guo:
The i.MX fixes for 4.4, 2nd round:
- Fix vf610 SAI clock configuration bug which is discovered by the newly
added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
* tag 'imx-fixes-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
|
|
Some USB device / host controller combinations seem to have problems
with Link Power Management. For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.
This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.
On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.
On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.
There are a few issues with this approach
1. A host initiated resume will also generate a resume event. The event
handler will find the port in resume state, believe it's a device
initiated resume, and act accordingly.
2. A port status request might cut the resume signalling short if a
get_port_status request is handled during the host resume signalling.
The port will be found in resume state. The timestamp is not set leading
to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
get_port_status will proceed with moving the port to U0.
3. If an error, or anything else happens to the port during device
initiated resume signalling it will leave all the device resume
parameters hanging uncleared, preventing further suspend, returning
-EBUSY, and cause the pm thread to busyloop trying to enter suspend.
Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state
This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS
Cc: stable <stable@vger.kernel.org>
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Even if dev->driver is null because we are being removed,
it is safer to not leave device locked.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The Atmel maxtouch DT binding documents that the compatible string for
the device is "atmel,maxtouch" and the I2C core always reports a module
alias of the form i2c:alias where alias is the compatible string model:
$ grep MODALIAS /sys/devices/platform/12e00000.i2c/i2c-8/8-004b/uevent
MODALIAS=i2c:maxtouch
But there isn't maxtouch entry in the I2C device ID table so when the
i2c:maxtouch MODALIAS uevent is reported, kmod is not able to match the
alias with a module to load:
$ modinfo atmel_mxt_ts | grep alias
alias: of:N*T*Catmel,maxtouch
alias: i2c:mXT224
alias: i2c:atmel_mxt_tp
alias: i2c:atmel_mxt_ts
alias: i2c:qt602240_ts
So add the maxtouch entry to the I2C device ID table to allow the module
to be autoloaded when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
KASAN found that our additional element processing scripts drop off
the end of the VPD page into unallocated space. The reason is that
not every element has additional information but our traversal
routines think they do, leading to them expecting far more additional
information than is present. Fix this by adding a gate to the
traversal routine so that it only processes elements that are expected
to have additional information (list is in SES-2 section 6.1.13.1:
Additional Element Status diagnostic page overview)
Reported-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Tested-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Five stable fixes:
- Two DM btree bufio buffer leak fixes that resolve reported BUG_ONs
during DM thinp metadata close's dm_bufio_client_destroy().
- A DM thinp range discard fix to handle discarding a partially
mapped range.
- A DM thinp metadata snapshot fix to make sure the btree roots saved
in the metadata snapshot are the most current.
- A DM space map metadata refcounting fix that improves both DM thinp
and DM cache metadata"
* tag 'dm-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm btree: fix bufio buffer leaks in dm_btree_del() error path
dm space map metadata: fix ref counting bug when bootstrapping a new space map
dm thin metadata: fix bug when taking a metadata snapshot
dm thin metadata: fix bug in dm_thin_remove_range()
dm btree: fix leak of bufio-backed block in btree_split_sibling error path
|
|
Pull drm fixes from Dave Airlie:
"Not too much this time.
- One nouveau workaround extended to a few more GPUs
- Some amdgpu big endian fixes, and a regression fixer
- Some vmwgfx fixes
- One ttm locking fix
- One vgaarb fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
vgaarb: fix signal handling in vga_get()
radeon: Fix VCE IB test on Big-Endian systems
radeon: Fix VCE ring test for Big-Endian systems
radeon/cik: Fix GFX IB test on Big-Endian
drm/amdgpu: fix the lost duplicates checking
drm/nouveau/pmu: remove whitelist for PGOB-exit WAR, enable by default
drm/vmwgfx: Implement the cursor_set2 callback v2
drm/vmwgfx: fix a warning message
drm/ttm: Fixed a read/write lock imbalance
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There are few defects in vga_get() related to signal hadning:
- we shouldn't check for pending signals for TASK_UNINTERRUPTIBLE
case;
- if we found pending signal we must remove ourself from wait queue
and change task state back to running;
- -ERESTARTSYS is more appropriate, I guess.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: stable@vger.kernel.org
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
into drm-fixes
some big endian fixes and one regression fix.
* 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux:
radeon: Fix VCE IB test on Big-Endian systems
radeon: Fix VCE ring test for Big-Endian systems
radeon/cik: Fix GFX IB test on Big-Endian
drm/amdgpu: fix the lost duplicates checking
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into fixes
Merge "Fixes for Exynos" from Krzysztof Kozlowski:
1. Fix potential NULL pointer dereference in Exynos PMU driver.
2. Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
* tag 'samsung-fixes-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Most are minor to important fixes.
There is one performance enhancement that I took on the grounds that
failing to check if other processes can run before running what's
intended to be a background, idle-time task is a bug, even though the
primary effect of the fix is to improve performance (and it was a very
simple patch)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/mlx5: Postpone remove_keys under knowledge of coming preemption
IB/mlx4: Use vmalloc for WR buffers when needed
IB/mlx4: Use correct order of variables in log message
iser-target: Remove explicit mlx4 work-around
mlx4: Expose correct max_sge_rd limit
IB/mad: Require CM send method for everything except ClassPortInfo
IB/cma: Add a missing rcu_read_unlock()
IB core: Fix ib_sg_to_pages()
IB/srp: Fix srp_map_sg_fr()
IB/srp: Fix indirect data buffer rkey endianness
IB/srp: Initialize dma_length in srp_map_idb
IB/srp: Fix possible send queue overflow
IB/srp: Fix a memory leak
IB/sa: Put netlink request into the request list before sending
IB/iser: use sector_div instead of do_div
IB/core: use RCU for uverbs id lookup
IB/qib: Minor fixes to qib per SFF 8636
IB/core: Fix user mode post wr corruption
IB/qib: Fix qib_mr structure
|
|
The calculation equation of PAD_OWN register offset is not
correct for Broxton, verified this fix will get right
offset for Broxton.
Signed-off-by: Qi Zheng <qi.zheng@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The group size for registers PADCFGLOCK, HOSTSW_OWN, GPI_IS,
GPI_IE, are not 24 for Broxton, Add a parameter to allow
different platform to set correct value.
Signed-off-by: Qi Zheng <qi.zheng@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The EP93xx is registering a clocksource of 40 bits with
clocksource_mmio_init() but this is not working because of this
artificial limitation. It works fine to lift the uppe limit to
64 bits, and since cycle_t is u64, it should intuitively have been
like that from the beginning.
Fixes: 000bc17817bf "ARM: ep93xx: switch to GENERIC_CLOCKEVENTS"
Reported-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/1449768101-6879-1-git-send-email-linus.walleij@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This reverts commit 49718f0fb8c9 ("SCSI: Fix NULL pointer dereference in
runtime PM")
The old commit may lead to a issue that blk_{pre|post}_runtime_suspend and
blk_{pre|post}_runtime_resume may not be called in pairs.
Take sr device as example, when sr device goes to runtime suspend,
blk_{pre|post}_runtime_suspend will be called since sr device defined
pm->runtime_suspend. But blk_{pre|post}_runtime_resume will not be called
since sr device doesn't have pm->runtime_resume. so, sr device can not
resume correctly anymore.
More discussion can be found from below link.
http://marc.info/?l=linux-scsi&m=144163730531875&w=2
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Xiangliang Yu <Xiangliang.Yu@amd.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Terry <Michael.terry@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
To support i.MX7D Low Power State Retention IOMUXC, commit e7b37a522aa9
("pinctrl: freescale: imx: allow mux_reg offset zero") changes the way
of zero mux_reg offset support with a new flag ZERO_OFFSET_VALID. But,
unfortunately, it forgot to add this flag for vf610 pinctrl which has
zero mux_reg offset be valid as well, and hence breaks the vf610
support.
Fix the regression by adding flag ZERO_OFFSET_VALID for vf610 pinctrl
driver.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixes: e7b37a522aa9 ("pinctrl: freescale: imx: allow mux_reg offset zero")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
TMP102 works based on conversions done periodically. However, as per
the TMP102 data sheet[1] the first conversion is triggered immediately
after we program the configuration register. The temperature data
registers do not reflect proper data until the first conversion is
complete (in our case HZ/4).
The driver currently sets the last_update to be jiffies - HZ, just
after the configuration is complete. When TMP102 driver registers
with the thermal framework, it immediately tries to read the sensor
temperature data. This takes place even before the conversion on the
TMP102 is complete and results in an invalid temperature read.
Depending on the value read, this may cause thermal framework to
assume that a critical temperature event has occurred and attempts to
shutdown the system.
Instead of causing an invalid mid-conversion value to be read
erroneously, we mark the last_update to be in-line with the current
jiffies. This allows the tmp102_update_device function to skip update
until the required conversion time is complete. Further, we ensure to
return -EAGAIN result instead of returning spurious temperature (such
as 0C) values to the caller to prevent any wrong decisions made with
such values. NOTE: this allows the read functions not to be blocking
and allows the callers to make the decision if they would like to
block or try again later. At least the current user(thermal) seems to
handle this by retrying later.
A simpler alternative approach could be to sleep in the probe for the
duration required, but that will result in latency that is undesirable
and delay boot sequence un-necessarily.
[1] http://www.ti.com/lit/ds/symlink/tmp102.pdf
Cc: Eduardo Valentin <edubezval@gmail.com>
Reported-by: Aparna Balasubramanian <aparnab@ti.com>
Reported-by: Elvita Lobo <elvita@ti.com>
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Simple enclosure implementations (mostly USB) are allowed to return only
page 8 to every diagnostic query. That really confuses our
implementation because we assume the return is the page we asked for and
end up doing incorrect offsets based on bogus information leading to
accesses outside of allocated ranges. Fix that by checking the page
code of the return and giving an error if it isn't the one we asked for.
This should fix reported bugs with USB storage by simply refusing to
attach to enclosures that behave like this. It's also good defensive
practise now that we're starting to see more USB enclosures.
Reported-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: stable@vger.kernel.org
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If dm_btree_del()'s call to push_frame() fails, e.g. due to
btree_node_validator finding invalid metadata, the dm_btree_del() error
path must unlock all frames (which have active dm-bufio buffers) that
were pushed onto the del_stack.
Otherwise, dm_bufio_client_destroy() will BUG_ON() because dm-bufio
buffers have leaked, e.g.:
device-mapper: bufio: leaked buffer 3, hold count 1, list 0
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
This patch adds a reverse mapping from a digital port number to
intel_encoder object containing the corresponding intel_digital_port.
It simplifies the query of the encoder a lot.
Note that, even if it's a valid digital port, the dig_port_map[] might
point still to NULL -- usually it implies a DP MST port. Due to this
fact, the NULL check in each place has no WARN_ON() and just skips the
port. Once when the situation changes in future, we might introduce
WARN_ON() for a more strict check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Implement a new i915_audio_component_ops, get_eld(). It's called by
the audio driver to fetch the current audio status and ELD of the
given HDMI/DP port. It returns the size of expected ELD bytes if it's
valid, zero if no valid ELD is found, or a negative error code. The
current state of audio on/off is stored in the given pointer, too.
Note that the returned size isn't limited to the given max bytes. If
the size is greater than the max bytes, it means that only a part of
ELD has been copied back.
For achieving this implementation, a new field audio_connector is
added to struct intel_digital_port. It points to the connector
assigned to the given digital port. It's set/reset at each audio
enable/disable call in intel_audio.c, and protected with av_mutex.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When disable_noatomic is called plane_mask is not correct yet, and
plane_state->visible = true is left as true after disabling the primary
plane.
Other planes are already disabled as part of crtc sanitization, only the
primary is left active. But the plane_mask is not updated here. It gets
updated during fb takeover in modeset_gem_init, or set to the new value
on resume.
This means that to disable the primary plane 1 << drm_plane_index(primary)
needs to be used.
Afterwards because the crtc is no longer active it's forbidden to keep
plane_state->visible set, or a WARN_ON in
intel_plane_atomic_calc_changes triggers. There are other code points
that rely on accurate plane_state->visible too, so make sure the bool is
cleared.
The other planes are already disabled in intel_sanitize_crtc, so they
don't have to be handled here.
Cc: stable@vger.kernel.org #v4.3, v4.2?
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92655
Tested-by: Tomas Mezzadra <tmezzadra@gmail.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/5652DB88.9070208@linux.intel.com
(cherry picked from commit 54a4196188eab82e6f0a5f05716626e9f18b8fb6)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
This patch fixes at_xdmac_prep_dma_memcpy(). Indeed the data width field
of the Channel Configuration register was not updated properly in the
loop: the bits of the dwidth field were not cleared before adding their
new value.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee70 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
|
|
This change makes the DT file to be easier to read since the reserved slots
array does not need the '/bits/ 16' to be specified, which might confuse
some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This change makes the DT file to be easier to read since the memcpy
channels array does not need the '/bits/ 16' to be specified, which might
confuse some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Pull VFIO fixes from Alex Williamson:
- Various fixes for removing redundancy, const'ifying structs, avoiding
stack usage, fixing WARN usage (Krzysztof Kozlowski, Julia Lawall,
Kees Cook, Dan Carpenter)
- Revert No-IOMMU mode as the intended user has not emerged (Alex
Williamson)
* tag 'vfio-v4.4-rc5' of git://github.com/awilliam/linux-vfio:
Revert: "vfio: Include No-IOMMU mode"
vfio: fix a warning message
vfio: platform: remove needless stack usage
vfio-pci: constify pci_error_handlers structures
vfio: Drop owner assignment from platform_driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DT fixes from Rob Herring:
"I think this should be all for 4.4:
- Fix incorrect warning about overlapping memory regions
- Export of_irq_find_parent again which was made static in 4.4, but
has users pending for 4.5.
- Fix of_msi_map_rid declaration location
- Fix re-entrancy for of_fdt_unflatten_tree
- Clean-up of phys_addr_t printks"
* tag 'devicetree-fixes-for-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/irq: move of_msi_map_rid declaration to the correct ifdef section
of/irq: Export of_irq_find_parent again
of/fdt: Add mutex protection for calls to __unflatten_device_tree()
of/address: fix typo in comment block of of_translate_one()
of: do not use 0x in front of %pa
of: Fix comparison of reserved memory regions
|
|
A runtime PM centric subsystem/driver may typically use the runtime PM
helpers, pm_runtime_force_suspend|resume() in the system PM path. This
means the genpd's runtime PM callbacks might be invoked even when runtime
PM has been disabled for the device.
To properly cope with these and similar scenarios when these helper
functions are used, change genpd to skip validating and measuring the
device PM QOS latency.
This is needed because otherwise genpd may prevent the device to be put
into low power state. If this occurs during system PM, it causes the
sequence to be aborted as a device's system PM callback returns -EBUSY.
Fixes: ba2bbfbf6307 (PM / Domains: Remove intermediate states from the power off sequence)
Reported-by: Cao Minh Hiep <cm-hiep@jinso.co.jp>
Reported-by: Harunaga <nx-truong@jinso.co.jp>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: 4.3+ <stable@vger.kernel.org> # 4.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One small build fix, a couple do_div() fixes, and a fix for the gpio
basic clock type are the major changes here. There's also a couple
fixes for the TI, sunxi, and scpi clock drivers"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi: pll2: Fix clock running too fast
clk: scpi: add missing of_node_put
clk: qoriq: fix memory leak
imx/clk-pllv2: fix wrong do_div() usage
imx/clk-pllv1: fix wrong do_div() usage
clk: mmp: add linux/clk.h includes
clk: ti: drop locking code from mux/divider drivers
clk: ti816x: Add missing dmtimer clkdev entries
clk: ti: fapll: fix wrong do_div() usage
clk: ti: clkt_dpll: fix wrong do_div() usage
clk: gpio: Get parent clk names in of_gpio_clk_setup()
|
