Age | Commit message (Collapse) | Author |
|
If we receive a transfer event indicating that an endpoint should be
halted, but current endpoint state doesn't match it, then the halt might
be just resolved by the stop endpoint completion handler that detects the
halted endpoint due to a context state error.
In this case the TD we halted on is already moved to the cancelled TD list,
and should not be successfully completed and given back anymore.
Let the stop endpoint completion handler reset the endpoint, and then let
the reset endpoint handler give back the cancelled TD among all other
ones on the cancelled TD list
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-28-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A halted endpoint can be detected both when transfer events complete, and
in stop endpoint command completion. Both these handlers will start
clearing up the halted endpoint and queue a reset endpoint command.
It's possible to get both events for the same halted endpoint if right
after a URB cancel queues a stop endpoint command the endpoint stalls.
Use the EP_HALTED flag to prevent resetting the endpoint twice.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-27-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_find_new_dequeue_state() and xhci_queue_new_dequeue_state() are no
longer used afer introducing the move_dequeue_past_td() function.
also remove struct xhci_dequeue_state as its no longer used.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-26-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace xhci_find_new_dequeue_state() and xhci_queue_new_dequeue_state()
functions with one combined function.
These function were always called after each other, and had a lot of extra
code just to pass the newly found dequeue state from the first function
to the other.
The new function also returns error in case there is a failure to
queue the new dequeue state. This way the caller can decide on
recovery measures to handle it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-25-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Handle race where a stop endpoint command fails with "context state error"
as hardware hasn't actually started the ring yet after a previous urb
cancellation completed and restarted the endpoint.
Flushing the doorbell write that restart the endpoint reduced these cases,
but didn't completely resolve them.
Check if the ring is running in the stop endpoint completion handler, and
issue a new stop endpoint command in this case.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-24-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci 4.6.9: "A busy endpoint may asynchronously transition from the
Running to the Halted or Error state due to error conditions detected
while processing TRBs. A possible race condition may occur if software,
thinking an endpoint is in the running state, issues a Stop Endpoint
Command, however at the same time the xHC asynchronously transitions
the endpoint to the Halted or Error state. In this case, a Context
State Error may be generated for the command completion. Software
may verify that this case occurred by inspecting the EP State for
Halted or Error when a Stop Endpoint Command results in a Context
State Error."
Halted endpoints were not detected or handled at all in the stop endpoint
completion handler. A set TR Deq ptr command was bluntly queued instead
of resetting the endpoint first. The set TR Deq command would fail with
a context state error.
Fix this case by resetting the halted endpoint first to get it to a
stopped state instead of the halted (error) state.
Handle cancelled TDs once endpoint reset completes,
invalidating cancelled TDs on ring either by turning them to no-op,
or in case ring stopped on cancelled TD then move hardware dequeue pointer
past it, which will clear the cancelled TD from hw cache, and make sure
HW does not process it
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-23-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't queue both a reset endpoint command and a
set TR deq command at once when handling a halted endpoint.
split this into two steps.
Initially only queue a reset endpoint command, and then if needed queue a
set TR deq command in the reset endpoint handler.
Note: This removes the RESET_EP_QUIRK handling which was added in
commit ac9d8fe7c6a8 ("USB: xhci: Add quirk for Fresco Logic xHCI hardware.")
This quirk was added in 2009 for prototype xHCI hardware meant for
evaluation purposes only, and should not reach consumers.
This hardware could not handle two commands queued at once, and had
bad data in the output context after a reset endpoint command.
After this patch two command are no longer queued at once, so that
part is solved in this rewrite, but the workaround for bad data in the
output context solved by issuing an extra configure endpoint command is
bluntly removed.
Adding this workaround to the new rewrite just adds complexity, and I
think it's time to let this quirk go.
Print a debug message instead.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Halted endpoints can be discoverd both when handling transfer events and
command completion events. Move code that handles halted endpoints before
both of those event handlers.
Rename the function to xhci_handle_halted_ep() to better describe
what it does. Try to reserve "cleanup" word in function names for last
stage cleanup activities.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Refactor handler for stop endpoint command completion. Yank out the part
that invalidates cancelled TDs and turn it into a separate function.
Invalidating cancelled TDs should be done while the ring is stopped,
but not exclusively in the stop endpoint command completeion handler.
We will need to invalidate TDs after resetting endpoints as well.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In cases where the TD can't be given back in current handler we want
to be able to store it until its time to return the TD.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
use the existing xhci_td_cleanup() to give back cancelled TDs when a
ring is stopped.
A minor change to make sure we don't try to remove an already removed
td from the list is needed as cancelled TDs are already removed from the
td_list immediatelty when it's cancelled.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
No funtional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Create a separate helper function to issue reset endpont commands
to clear halted endpoints.
This is useful for cases where a halted endpoint is discovered while
completing another command, and the endpoint halt needs to be cleared
with a endpoint reset first.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Stop endpoint command fails with "context state error" if the endpoint is
already stopped.
This case was observed when a previous URB cancel had just completed and
rang the doorbell to restart the ring, when a new URB cancel queued a stop
endpoint command.
>From xHC hardware pov the endpoint had not yet started, so the stop
endpoint command failed with context state error.
Right after this the doorbell ring took effect and ring was restarted.
Interrupt handler saw a stop endpoint command completion event with
"context state error" and discovered that the ring was back up in
running state.
flushing the write reduces these cases in stress testing, but does not
completely remove the issue.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci driver relies on link TRBs existing in the correct places in TRB
ring buffers shared with the host controller.
The controller should not modify these link TRBs, but in theory a faulty
xHC could do it.
Add some basic sanity checks to avoid infinite loops in interrupt handler,
or accessing unallocated memory outside a ring segment due to missing or
misplaced link TRBs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of re-reading, masking and endianness correcting the same trb
several times to get the trb type from an event, just do it once and
store it in a local variable.
Also pass the trb_type directly to the vendor specific event handler,
avoiding one more similar read.
In addition to the security benefit this also cleans up the code
and helps readability.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When finishing a TD we walk the endpoint dequeue trb pointer
until it matches the last TRB of the TD.
TDs can contain over 100 TRBs, meaning we call a function 100 times,
do a few comparisons and increase a couple values for each of these calls,
all in interrupt context.
This can all be avoided by adding a pointer to the last TRB segment, and
a number of TRBs in the TD. So instead of walking through each TRB just
set the new dequeue segment, pointer, and number of free TRBs directly.
Getting rid of the while loop also reduces the risk of getting stuck in a
infinite loop in the interrupt handler. Loop relied on valid matching
dequeue and last_trb values to break.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check that the slot_id that we dug out from command completion event
TRB, is valid before using it to identify the slot associated with the
command that generated the event.
Signed-off-by: Lalithambika Krishna Kumar <lalithambika.krishnakumar@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci driver links together segments in a ring buffer by turning the last
TRB of a segment into a link TRB, pointing to the beginning of
the next segment.
If the first TRB of every segment for some unknown reason is a link TRB
pointing to the next segment, then prepare_ring() loops indefinitely.
This isn't something the xhci driver would do.
xHC hardware has access to these rings, it sholdn't be writing link
TRBs either, but with broken xHC hardware this could in theory be
possible.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The one case that used this function can use the
xhci_triad_to_transfer_ring() helper instead.
Avoid having several functions doing basically the same thing.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Two existing ring helpers, xhci_triad_to_transfer_ring() and
xhci_stream_id_to_ring() have partially similar functionality.
Both have some limitation, especieally with boundary checking.
Add a new xhci_virt_ep_to_ring() helper with proper boundary checking
that can replace parts of one helper, and later will completely
replace the other helper.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check that the xhci_virt_dev structure that we dug out based
on a slot_id value from a command completion is valid before
dereferencing it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In several event handlers we need to find the right endpoint
structure from slot_id and ep_index in the event.
Add a helper for this, check that slot_id and ep_index are valid.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
several command completion handlers are passed the event trb
as a paramtere even if it't not used.
Remove it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of passing slot id and endpoint index to
cleanup_halted_endpoint() pass the endpoint structure pointer
as it's already known.
Avoids again digging out the endpoint structure based on
slot id and endpoint index, and passing them along the
call chain for this purpose only.
Add slot_id to the virt_dev structure so that it
can easily be found from a virt_dev, or its child, the
virt_ep endpoint structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
isochronous endpoints do not support streams, meaning that
there is only one ring per endpoint.
Avoid double-fetching the transfer event DMA to get the
ring. Also makes passing the event to skip_isoc_td() uncecessary.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When handling transfer events the event is passed along the handling
callpath and parsed again in several occasions.
The event contains slot_id and endpoint index, from which the driver
endpoint structure can be found. There wasn't however a way to get the
endpoint index or parent usb device from this endpoint structure.
A lot of extra event parsing, and thus some DMA doublefetch cases,
and excess variables and code can be avoided by adding endpoint index
and parent usb virt device pointer to the endpoint structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With some USB network adapters, such as DM96xx, the following message
is seen for each maximum size receive packet.
dwc2 ff540000.usb: dwc2_update_urb_state(): trimming xfer length
This happens because the packet size requested by the driver is 1522
bytes, wMaxPacketSize is 64, the dwc2 driver configures the chip to
receive 24*64 = 1536 bytes, and the chip does indeed send more than
1522 bytes of data. Since the event does not indicate an error condition,
the message is just noise. Demote it to debug level.
Fixes: 7359d482eb4d3 ("staging: HCD files for the DWC2 driver")
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-4-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In some situations, the following error messages are reported.
dwc2 ff540000.usb: dwc2_hc_chhltd_intr_dma: Channel 1 - ChHltd set, but reason is unknown
dwc2 ff540000.usb: hcint 0x00000002, intsts 0x04000021
This is sometimes followed by:
dwc2 ff540000.usb: dwc2_update_urb_state_abn(): trimming xfer length
and then:
WARNING: CPU: 0 PID: 0 at kernel/v4.19/drivers/usb/dwc2/hcd.c:2913
dwc2_assign_and_init_hc+0x98c/0x990
The warning suggests that an odd buffer address is to be used for DMA.
After an error is observed, the receive buffer may be full
(urb->actual_length >= urb->length). However, the urb is still left in
the queue unless three errors were observed in a row. When it is queued
again, the dwc2 hcd code translates this into a 1-block transfer.
If urb->actual_length (ie the total expected receive length) is not
DMA-aligned, the buffer pointer programmed into the chip will be
unaligned. This results in the observed warning.
To solve the problem, abort input transactions after an error with
unknown cause if the entire packet was already received. This may be
a bit drastic, but we don't really know why the transfer was aborted
even though the entire packet was received. Aborting the transfer in
this situation is less risky than accepting a potentially corrupted
packet.
With this patch in place, the 'ChHltd set' and 'trimming xfer length'
messages are still observed, but there are no more transfer attempts
with odd buffer addresses.
Fixes: 151d0cbdbe860 ("usb: dwc2: make the scheduler handle excessive NAKs better")
Cc: Boris ARZUR <boris@konbu.org>
Cc: Douglas Anderson <dianders@chromium.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-3-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DWC2 documentation states that transfers with zero data length should
set the number of packets to 1 and the transfer length to 0. This is not
currently the case for inbound transfers: the transfer length is set to
the maximum packet length. This can have adverse effects if the chip
actually does transfer data as it is programmed to do. Follow chip
documentation and keep the transfer length set to 0 in that situation.
Fixes: 56f5b1cff22a1 ("staging: Core files for the DWC2 driver")
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-2-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update Raw Gadget documentation and Kconfig. Make the description more
precise and clear, fix typos and grammar mistakes, and do other cleanups.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/f4c650c94ae2b910e38819d51109cd5f0b251a2a.1611429174.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add copyright to drivers/usb/gadget/legacy/raw_gadget.c.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/c8937266c4a5da073ac81cd471b18d869c984dfe.1611429174.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Tasklets have long been deprecated as being too heavy on the system
by running in irq context - and this is not a performance critical
path. If a higher priority process wants to run, it must wait for
the tasklet to finish before doing so.
c67x00_do_work() will now run in process context and have further
concurrency (tasklets being serialized among themselves), but this
is done holding the c67x00->lock, so it should be fine. Furthermore,
this patch fixes the usage of the lock in the callback as otherwise
it would need to be irq-safe.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Link: https://lore.kernel.org/r/20210113031537.79859-1-dave@stgolabs.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add terminating '\n' to the formats where missed.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210124143947.1688-1-angkery@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PTR_ERR(chip->tcpci) has been used as a return value,
it is not necessary to assign it to ret, so remove it.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210124143853.1630-1-angkery@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the port partner is PD2, the PDOs of the local port should follow the
format defined in PD2 Spec. Dynamically modify the pre-defined PD3 PDOs
and transform them into PD2 format before sending them to the PD2 port
partner.
Reviewed-by: Guenter Roeck <linux@roeckus.net>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210115163311.391332-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the fixes in here and this resolves a merge issue with
drivers/usb/gadget/udc/bdc/Kconfig.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull arch/sh updates from Rich Felker:
"Cleanup and warning fixes"
* tag 'sh-for-5.11' of git://git.libc.org/linux-sh:
sh/intc: Restore devm_ioremap() alignment
sh: mach-sh03: remove duplicate include
arch: sh: remove duplicate include
sh: Drop ARCH_NR_GPIOS definition
sh: Remove unused HAVE_COPY_THREAD_TLS macro
sh: remove CONFIG_IDE from most defconfig
sh: mm: Convert to DEFINE_SHOW_ATTRIBUTE
sh: intc: Convert to DEFINE_SHOW_ATTRIBUTE
arch/sh: hyphenate Non-Uniform in Kconfig prompt
sh: dma: fix kconfig dependency for G2_DMA
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph:
- fix a status code in nvmet (Chaitanya Kulkarni)
- avoid double completions in nvme-rdma/nvme-tcp (Chao Leng)
- fix the CMB support to cope with NVMe 1.4 controllers (Klaus Jensen)
- fix PRINFO handling in the passthrough ioctl (Revanth Rajashekar)
- fix a double DMA unmap in nvme-pci
- lightnvm error path leak fix (Pan)
- MD pull request from Song:
- Flush request fix (Xiao)
* tag 'block-5.11-2021-01-24' of git://git.kernel.dk/linux-block:
lightnvm: fix memory leak when submit fails
nvme-pci: fix error unwind in nvme_map_data
nvme-pci: refactor nvme_unmap_data
md: Set prev_flush_start and flush_bio in an atomic way
nvmet: set right status on error in id-ns handler
nvme-pci: allow use of cmb on v1.4 controllers
nvme-tcp: avoid request double completion for concurrent nvme_tcp_timeout
nvme-rdma: avoid request double completion for concurrent nvme_rdma_timeout
nvme: check the PRINFO bit before deciding the host buffer length
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc driver fixes for 5.11-rc5:
- habanalabs driver fixes
- phy driver fixes
- hwtracing driver fixes
- rtsx cardreader driver fix
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc: rtsx: init value of aspm_enabled
habanalabs: disable FW events on device removal
habanalabs: fix backward compatibility of idle check
habanalabs: zero pci counters packet before submit to FW
intel_th: pci: Add Alder Lake-P support
stm class: Fix module init return on allocation failure
habanalabs: prevent soft lockup during unmap
habanalabs: fix reset process in case of failures
habanalabs: fix dma_addr passed to dma_mmap_coherent
phy: mediatek: allow compile-testing the dsi phy
phy: cpcap-usb: Fix warning for missing regulator_disable
PHY: Ingenic: fix unconditional build of phy-ingenic-usb
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some small driver core fixes for 5.11-rc5 that resolve some
reported problems:
- revert of a -rc1 patch that was causing problems with some machines
- device link device name collision problem fix (busses only have to
name devices unique to their bus, not unique to all busses)
- kernfs splice bugfixes to resolve firmware loading problems for
Qualcomm systems.
- other tiny driver core fixes for minor issues reported.
All of these have been in linux-next with no reported problems"
* tag 'driver-core-5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Fix device link device name collision
driver core: Extend device_is_dependent()
kernfs: wire up ->splice_read and ->splice_write
kernfs: implement ->write_iter
kernfs: implement ->read_iter
Revert "driver core: Reorder devices on successful probe"
Driver core: platform: Add extra error check in devm_platform_get_irqs_affinity()
drivers core: Free dma_range_map when driver probe failed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver fixes from Greg KH:
"Here are some IIO driver fixes for 5.11-rc5 to resolve some reported
problems.
Nothing major, just a few small fixes, all of these have been in
linux-next for a while and full details are in the shortlog"
* tag 'staging-5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: sx9310: Fix semtech,avg-pos-strength setting when > 16
iio: common: st_sensors: fix possible infinite loop in st_sensors_irq_thread
iio: ad5504: Fix setting power-down state
counter:ti-eqep: remove floor
drivers: iio: temperature: Add delay after the addressed reset command in mlx90632.c
iio: adc: ti_am335x_adc: remove omitted iio_kfifo_free()
dt-bindings: iio: accel: bma255: Fix bmc150/bmi055 compatible
iio: sx9310: Off by one in sx9310_read_thresh()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are three small tty/serial fixes for 5.11-rc5 to resolve reported
problems:
- two patches to fix up writing to ttys with splice
- mvebu-uart driver fix for reported problem
All of these have been in linux-next with no reported problems"
* tag 'tty-5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: fix up hung_up_tty_write() conversion
tty: implement write_iter
serial: mvebu-uart: fix tx lost characters at power off
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes for 5.11-rc5. They resolve:
- xhci issues for some reported problems
- ehci driver issue for one specific device
- USB gadget fixes for some reported problems
- cdns3 driver fixes for issues reported
- MAINTAINERS file update
- thunderbolt minor fix
All of these have been in linux-next with no reported issues"
* tag 'usb-5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: bdc: Make bdc pci driver depend on BROKEN
xhci: tegra: Delay for disabling LFPS detector
xhci: make sure TRB is fully written before giving it to the controller
usb: udc: core: Use lock when write to soft_connect
USB: gadget: dummy-hcd: Fix errors in port-reset handling
usb: gadget: aspeed: fix stop dma register setting.
USB: ehci: fix an interrupt calltrace error
ehci: fix EHCI host controller initialization sequence
MAINTAINERS: update Peter Chen's email address
thunderbolt: Drop duplicated 0x prefix from format string
MAINTAINERS: Update address for Cadence USB3 driver
usb: cdns3: imx: improve driver .remove API
usb: cdns3: imx: fix can't create core device the second time issue
usb: cdns3: imx: fix writing read-only memory issue
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Fix a kernel panic in mips-cpu due to invalid irq domain hierarchy.
- Fix to not lose IPIs on bcm2836.
- Fix for a bogus marking of ITS devices as shared due to unitialized
stack variable.
- Clear a phantom interrupt on qcom-pdc to unblock suspend.
- Small cleanups, warning and build fixes.
* tag 'irq_urgent_for_v5.11_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Export irq_check_status_bit()
irqchip/mips-cpu: Set IPI domain parent chip
irqchip/pruss: Simplify the TI_PRUSS_INTC Kconfig
irqchip/loongson-liointc: Fix build warnings
driver core: platform: Add extra error check in devm_platform_get_irqs_affinity()
irqchip/bcm2836: Fix IPI acknowledgement after conversion to handle_percpu_devid_irq
irqchip/irq-sl28cpld: Convert comma to semicolon
genirq/msi: Initialize msi_alloc_info before calling msi_domain_prepare_irqs()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal.
* 'mtd/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: omap: Use BCH private fields in the specific OOB layout
mtd: spinand: Fix MTD_OPS_AUTO_OOB requests
mtd: rawnand: intel: check the mtd name only after setting the variable
mtd: rawnand: nandsim: Fix the logic when selecting Hamming soft ECC engine
mtd: rawnand: gpmi: fix dst bit offset when extracting raw payload
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Another bunch of driver fixes"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sprd: depend on COMMON_CLK to fix compile tests
Revert "i2c: imx: Remove unused .id_table support"
i2c: octeon: check correct size of maximum RECV_LEN packet
i2c: tegra: Create i2c_writesl_vi() to use with VI I2C for filling TX FIFO
i2c: bpmp-tegra: Ignore unknown I2C_M flags
i2c: tegra: Wait for config load atomically while in ISR
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Twelve minor fixes, all in drivers or doc.
Most of the fixes are pretty obvious (although we had two goes to get
the UFS sysfs doc right) and the biggest change is in the ufs driver
which they've extensively tested"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ibmvfc: Set default timeout to avoid crash during migration
scsi: target: tcmu: Fix use-after-free of se_cmd->priv
scsi: fnic: Fix memleak in vnic_dev_init_devcmd2
scsi: libfc: Avoid invoking response handler twice if ep is already completed
scsi: scsi_transport_srp: Don't block target in failfast state
scsi: docs: ABI: sysfs-driver-ufs: Rectify table formatting
scsi: ufs: Fix tm request when non-fatal error happens
scsi: ufs: Fix livelock of ufshcd_clear_ua_wluns()
scsi: ibmvfc: Fix missing cast of ibmvfc_event pointer to u64 handle
scsi: ufs: ufshcd-pltfrm depends on HAS_IOMEM
scsi: megaraid_sas: Fix MEGASAS_IOC_FIRMWARE regression
scsi: docs: ABI: sysfs-driver-ufs: Add DeepSleep power mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix DM integrity crash if "recalculate" used without "internal_hash"
- Fix DM integrity "recalculate" support to prevent recalculating
checksums if we use internal_hash or journal_hash with a key (e.g.
HMAC). Use of crypto as a means to prevent malicious corruption
requires further changes and was never a design goal for
dm-integrity's primary usecase of detecting accidental corruption.
- Fix a benign dm-crypt copy-and-paste bug introduced as part of a fix
that was merged for 5.11-rc4.
- Fix DM core's dm_get_device() to avoid filesystem lookup to get block
device (if possible).
* tag 'for-5.11/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: avoid filesystem lookup in dm_get_dev_t()
dm crypt: fix copy and paste bug in crypt_alloc_req_aead
dm integrity: conditionally disable "recalculate" feature
dm integrity: fix a crash if "recalculate" used without "internal_hash"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix initialization of block size when ext_csd isn't present
MMC host:
- sdhci-brcmstb: Fix mmc timeout errors on S5 suspend
- sdhci-of-dwcmshc: Fix request accessing RPMB
- sdhci-xenon: Fix 1.8v regulator stabilization"
* tag 'mmc-v5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: don't initialize block size from ext_csd if not present
mmc: sdhci-brcmstb: Fix mmc timeout errors on S5 suspend
mmc: sdhci-xenon: fix 1.8v regulator stabilization
mmc: sdhci-of-dwcmshc: fix rpmb access
|