| Age | Commit message (Collapse) | Author |
|---|
|
Gather the Tx packet and byte counts and call
netdev_tx_completed_queue() only once per clean cycle.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The descriptor mappings are set up the same way whether
or not it is a TSO, so we don't need separate logic for
the two cases.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the new ionic_tx_map_tso() usable by the non-TSO paths,
and pull the call up a level into ionic_tx() before calling
the csum or no-csum routines.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One issue with the original TSO code was that it was working too
hard to deal with skb layouts that were never going to show up,
such as an skb->data that was longer than a single descriptor's
length. The other issue was trying to arrange the fragment dma
mapping at the same time as figuring out the descriptors needed.
There was just too much going on at the same time.
Now we do the dma mapping first, which sets up the buffers with
skb->data in buf[0] and the remaining frags in buf[1..n-1].
Next we spread the bufs across the descriptors needed, where
each descriptor gets up to mss number of bytes.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the use of C bit-fields in the rmnet_map_ul_csum_header
structure with a single two-byte (big endian) structure member,
and use masks to encode or get values within it. The content of
these fields can be accessed using simple bitwise AND and OR
operations on the (host byte order) value of the new structure
member.
Previously rmnet_map_ipv4_ul_csum_header() would update C bit-field
values in host byte order, then forcibly fix their byte order using
a combination of byte swap operations and types.
Instead, just compute the value that needs to go into the new
structure member and save it with a simple byte-order conversion.
Make similar simplifications in rmnet_map_ipv6_ul_csum_header().
Finally, in rmnet_map_checksum_uplink_packet() a set of assignments
zeroes every field in the upload checksum header. Replace that with
a single memset() operation.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the use of C bit-fields in the rmnet_map_dl_csum_trailer
structure with a single one-byte field, using constant field masks
to encode or get at embedded values.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The actual layout of bits defined in C bit-fields (e.g. int foo : 3)
is implementation-defined. Structures defined in <linux/if_rmnet.h>
address this by specifying all bit-fields twice, to cover two
possible layouts.
I think this pattern is repetitive and noisy, and I find the whole
notion of compiler "bitfield endianness" to be non-intuitive.
Stop using C bit-fields for the command/data flag and the pad length
fields in the rmnet_map structure, and define a single-byte flags
field instead. Define a mask for the single-bit "command" flag,
and another mask for the encoded pad length. The content of both
fields can be accessed using a simple bitwise AND operation.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following macros, defined in "rmnet_map.h", assume a socket
buffer is provided as an argument without any real indication this
is the case.
RMNET_MAP_GET_MUX_ID()
RMNET_MAP_GET_CD_BIT()
RMNET_MAP_GET_PAD()
RMNET_MAP_GET_CMD_START()
RMNET_MAP_GET_LENGTH()
What they hide is pretty trivial accessing of fields in a structure,
and it's much clearer to see this if we do these accesses directly.
So rather than using these accessor macros, assign a local
variable of the map header pointer type to the socket buffer data
pointer, and derereference that pointer variable.
In "rmnet_map_data.c", use sizeof(object) rather than sizeof(type)
in one spot. Also, there's no need to byte swap 0; it's all zeros
irrespective of endianness.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rmnet_map_ipv4_ul_csum_header() and rmnet_map_ipv6_ul_csum_header()
the offset within a packet at which checksumming should commence is
calculated. This calculation involves byte swapping and a forced type
conversion that makes it hard to understand.
Simplify this by computing the offset in host byte order, then
converting the result when assigning it into the header field.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although there is platform issue of runtime suspend support
on CNP, it would be more flexible to let the user decide whether
to disable runtime or not because:
1. This can be done in userspace via
echo on > /sys/devices/pci0000\:00/0000\:00\:1f.d/power/control
2. More and more NICs would support runtime suspend, disabling the
runtime suspend on them by default would impact the validation.
Only disable runtime suspend on CNP in case of any user space regression.
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The NIC is put in runtime suspend status when there is no cable connected.
As a result, it is safe to keep non-wakeup NIC in runtime suspended during
s2ram because the system does not rely on the NIC plug event nor WoL to wake
up the system. Besides that, unlike the s2idle, s2ram does not need to
manipulate S0ix settings during suspend.
This patch introduces the .prepare() for e1000e so that if the NIC is runtime
suspended the subsequent suspend/resume hooks will be skipped so as to speed
up the s2ram. The pm core will check whether the NIC is a wake up device so
there's no need to check it again in .prepare(). DPM_FLAG_SMART_PREPARE flag
should be set during probe to ask the pci subsystem to honor the driver's
prepare() result. Besides, the NIC remains runtime suspended after resumed
from s2ram as there is no need to resume it.
Tested on i7-2600K with 82579V NIC
Before the patch:
e1000e 0000:00:19.0: pci_pm_suspend+0x0/0x160 returned 0 after 225146 usecs
e1000e 0000:00:19.0: pci_pm_resume+0x0/0x90 returned 0 after 140588 usecs
After the patch:
echo disabled > //sys/devices/pci0000\:00/0000\:00\:19.0/power/wakeup
becomes 0 usecs because the hooks will be skipped.
Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In review, Alexander Duyck suggested that ipa_table_hash_support()
was trivial enough that it could be implemented as a static inline
function in the header file. But the patch had already been
accepted. Implement his suggestion.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add basic support for the Marvell 88X2222 multi-speed ethernet
transceiver.
This PHY provides data transmission over fiber-optic as well as Twinax
copper links. The 88X2222 supports 2 ports of 10GBase-R and 1000Base-X
on the line-side interface. The host-side interface supports 4 ports of
10GBase-R, RXAUI, 1000Base-X and 2 ports of XAUI.
This driver, however, supports only XAUI on the host-side and
1000Base-X/10GBase-R on the line-side, for now. The SGMII is also
supported over 1000Base-X. Interrupts are not supported.
Internal registers access compliant with the Clause 45 specification.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split clocks settings from init callback into clks_config callback,
which could support platform level clocks management.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch intends to add platform level clocks management. Some
platforms may have their own special clocks, they also need to be
managed dynamically. If you want to manage such clocks, please implement
clks_config callback.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch intends to add clocks management for stmmac driver:
If CONFIG_PM enabled:
1. Keep clocks disabled after driver probed.
2. Enable clocks when up the net device, and disable clocks when down
the net device.
If CONFIG_PM disabled:
Keep clocks always enabled after driver probed.
Note:
1. It is fine for ethtool, since the way of implementing ethtool_ops::begin
in stmmac is only can be accessed when interface is enabled, so the clocks
are ticked.
2. The MDIO bus has a different life cycle to the MAC, need ensure
clocks are enabled when _mdio_read/write() need clocks, because these
functions can be called while the interface it not opened.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Intel mGbE controller such as those in EHL & TGL uses pcs-xpcs driver for
SGMII interface. To ensure mdio bus scanning does not assign phy_device
to MDIO-addressable entities like intel serdes and pcs-xpcs, we set up
to phy_mask to skip them.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the support for MAC-side SGMII C37 AN is added to pcs-xpcs, phydev
should be attached to phylink during driver's open(). So, we change the
condition to "Not C73 AN" instead.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all platform uses DT, so phylink_parse_mode() will skip in-band setup
of pl->supported and pl->link_config.advertising entirely. So, we add the
setting of ovr_an_inband flag to make it works for non-DT platform.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Certain platform does not support DT, so we make phylink_parse_mode() to
allow non-DT platform to use it to setup in-band AN advertising.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
XPCS IP supports C37 SGMII AN process and it is used in intel multi-GbE
controller as MAC-side SGMII.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation for XPCS is validated for C73, so we rename them
to have _c73 suffix and introduce a set of functions to use an_mode flag
to switch between C73 and C37 AN later.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
s/structue/structure/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
s/structue/structure/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mundane typo fix.
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This file has been effectively empty since 2.3.99-pre3 !
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the incorrect interface name is stored in the slaves/active_slave
option of the bonding sysfs, the kernel does not record the log that
interface does not exist.
This patch adds a log for -ENODEV error, which will facilitate users to
figure out such issue.
Signed-off-by: Jianlin Lv <Jianlin.Lv@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch implements unicast and multicast filtering per port.
Add support for it. By default filtering is disabled.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Optimize ice_run_xdp_zc() for the XDP program verdict being
XDP_REDIRECT in the xsk zero-copy path. This path is only used when
having AF_XDP zero-copy on and in that case most packets will be
directed to user space. This provides a little over 100k extra packets
in throughput on my server when running l2fwd in xdpsock.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Optimize ixgbe_run_xdp_zc() for the XDP program verdict being
XDP_REDIRECT in the xsk zero-copy path. This path is only used when
having AF_XDP zero-copy on and in that case most packets will be
directed to user space. This provides a little under 100k extra
packets in throughput on my server when running l2fwd in xdpsock.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Optimize i40e_run_xdp_zc() for the XDP program verdict being
XDP_REDIRECT in the xsk zero-copy path. This path is only used when
having AF_XDP zero-copy on and in that case most packets will be
directed to user space. This provides a little over 100k extra packets
in throughput on my server when running l2fwd in xdpsock.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Make use of the previously added metadata and report it to the psample
module. The metadata is read from the skb's control block, which was
initialized by the bus driver (i.e., 'mlxsw_pci') after decoding the
packet's Completion Queue Element (CQE).
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function resolves the psample sampling group from the Rx port
because this is the only form of sampling the driver currently supports.
Subsequent patches are going to add support for Tx-based and
policy-based sampling, in which case the sampling group would not be
resolved from the Rx port.
Therefore, move this code to the Rx-specific sampling listener.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 7d8e8f3433dc ("mlxsw: core: Increase scope of RCU read-side
critical section"), all Rx handlers are called from an RCU read-side
critical section.
Remove the unnecessary rcu_read_lock() / rcu_read_unlock().
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets that are mirrored / sampled to the CPU have extra metadata
encoded in their corresponding Completion Queue Element (CQE). Retrieve
this metadata from the CQE and set it in the skb control block so that
it could be accessed by the switch driver (i.e., 'mlxsw_spectrum').
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Next patch will need to encode more Rx metadata in the skb control
block, so create a dedicated field for it and move the cookie index
there.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Completion Queue Element version 2 (CQEv2) includes various metadata
fields for packets that are mirrored / sampled to the CPU.
Add these fields so that they could be used by a later patch.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow netdevsim to report "sampled" packets to the psample module by
periodically generating packets from a work queue. The behavior can be
enabled / disabled (default) and the various meta data attributes can be
controlled via debugfs knobs.
This implementation enables both testing of the psample module with all
the optional attributes as well as development of user space
applications on top of psample such as hsflowd and a Wireshark dissector
for psample generic netlink packets.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, callers of psample_sample_packet() pass three metadata
attributes: Ingress port, egress port and truncated size. Subsequent
patches are going to add more attributes (e.g., egress queue occupancy),
which also need an indication whether they are valid or not.
Encapsulate packet metadata in a struct in order to keep the number of
arguments reasonable.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BCM4908 switch has 256 CFP entrie, update that setting so CFP can be
used.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The batching logic in netvsc_send is non-trivial, due to
a combination of the Linux API and the underlying hypervisor
interface. Add a comment explaining why the code is written this
way.
Signed-off-by: Shachar Raindel <shacharr@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit eaf4fac47807 ("net: stmmac: Do not accept invalid MTU values")
started using the TX FIFO size to verify what counts as a valid MTU
request for the stmmac driver. This is unset for the ipq806x variant.
Looking at older patches for this it seems the RX + TXs buffers can be
up to 8k, so set appropriately.
(I sent this as an RFC patch in June last year, but received no replies.
I've been running with this on my hardware (a MikroTik RB3011) since
then with larger MTUs to support both the internal qca8k switch and
VLANs with no problems. Without the patch it's impossible to set the
larger MTU required to support this.)
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added a blank line after structure declaration.
This is done to maintain code uniformity.
Signed-off-by: Sanjana Srinidhi <sanjanasrinidhi1810@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
s/calclation/calculation/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow to dump the FDB table via devlink. This is a useful debugging feature.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two functions which need to populate fdb entries. Move that to a
helper function.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hellcreek_select_vlan() takes a boolean instead of an integer.
So, use false accordingly.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow to dump the VLAN table via devlink. This especially useful, because the
driver internally leverages VLANs for the port separation. These are not visible
via the bridge utility.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers
A follow-up patch will allow users to configures packet-per-second policing
in the software datapath. In preparation for this, teach all drivers that
support offload of the policer action to reject such configuration as
currently none of them support it.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the imp-controlled PHYs feature is enabled, driver can not
call phy driver interface to set loopback anymore and needs
to send command to firmware to start phy loopback.
Driver reuses the existing firmware command 0x0315 to start
phy loopback, just add a setting bit in this command. As this
command is not only for serdes loopback anymore, rename this
command to "xxx_COMMON_LOOPBACK", and modify function name,
macro name and logs related to it.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
