| Age | Commit message (Collapse) | Author |
|---|
|
Anyone working with an AMD Elan SC520 development or evaluation board
would be building a dedicated kernel for it, so we can make the
sc520cdp and netsc520 maps depend on MELAN. SC520_CPUFREQ already
depends on MELAN so it makes things more consistent. It also makes
kernel configuration for every other x86 user easier.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
The nand_chip::erase_cmd callback previously served a dual purpose; for
one, it allowed a per-flash-chip override, so that AG-AND devices could
use a different erase command than other NAND. These AND devices were
dropped in commit 14c6578683367b1e7af0c3c09e872b45a45183a7 (mtd: nand:
remove AG-AND support). On the other hand, some drivers (denali and
doc-g4) need to use this sort of callback to implement
controller-specific erase operations.
To make the latter operation easier for some drivers (e.g., ST's new BCH
NAND driver), it helps if the command dispatch and wait functions can be
lumped together, rather than called separately.
This patch does two things:
1. Pull the call to chip->waitfunc() into chip->erase_cmd(), and return
the status from this callback
2. Rename erase_cmd() to just erase(), since this callback does a
little more than just send a command
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
mtd_oobtest writes OOB, read it back and verify. The verification is
not correctly done if oobsize is not multiple of 4. Although the data
to be written and the data to be compared are generated by several
prandom_byte_state() calls starting with the same seed, these two are
generated with the different size and different number of calls.
Due to the implementation of prandom_byte_state() if the size on each
call is not multiple of 4, the resulting data is not always same.
This fixes it by just calling prandom_byte_state() once and using
correct range instead of calling it multiple times for each.
Reported-by: George Cherian <george.cherian@ti.com>
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Cc: George Cherian <george.cherian@ti.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Addition of the spi-nor framework, plus updates to the ST SPI FSM
driver.
|
|
COMPILE_TEST allows us to build this driver on other arch'es. But not
all arch'es have the right I/O accessors -- particularly, x86 is missing
readsl() and writesl().
So just restrict this driver to ARCH_STI. It's still buildable for a
multiplatform ARM kernel, so it can get decent compile coverage.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
|
|
Compile-testing for a 64-bit arch uncovers several bad casts:
In file included from include/linux/linkage.h:4:0,
from include/linux/kernel.h:6,
from drivers/mtd/devices/st_spi_fsm.c:15:
drivers/mtd/devices/st_spi_fsm.c: In function ‘stfsm_read_fifo’:
drivers/mtd/devices/st_spi_fsm.c:758:11: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
BUG_ON((((uint32_t)buf) & 0x3) || (size & 0x3));
...
Use uintptr_t instead of uint32_t, since it's guaranteed to be
pointer-sized.
We also see this warning, if size_t is not 32 bits wide:
In file included from drivers/mtd/devices/st_spi_fsm.c:15:0:
drivers/mtd/devices/st_spi_fsm.c: In function ‘stfsm_mtd_write’:
include/linux/kernel.h:712:17: warning: comparison of distinct pointer types lacks a cast [enabled by default]
(void) (&_min1 == &_min2); \
^
drivers/mtd/devices/st_spi_fsm.c:1704:11: note: in expansion of macro ‘min’
bytes = min(FLASH_PAGESIZE - page_offs, len);
^
Just use min_t() to force the type conversion, since we don't really
want to upgrade 'page_offs' and 'bytes' to size_t; they only should be
handling <= 256 byte offsets.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
|
|
This corrects some sparse warnings:
drivers/mtd/spi-nor/fsl-quadspi.c:281:31: warning: incorrect type in initializer (different address spaces) [sparse]
drivers/mtd/spi-nor/fsl-quadspi.c:281:31: expected void *[noderef] <asn:2>base [sparse]
drivers/mtd/spi-nor/fsl-quadspi.c:281:31: got void [noderef] <asn:2>*iobase [sparse]
(etc.)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
|
|
More and more chips use the GPMI controller, but these chips may use different
version of the IPs for GPMI and BCH. Different IPs have
different features, such as the BCH's maximum ECC strength:
imx23/imx28 -- the BCH's maximum ECC strength is 20
imx6q -- the BCH's maximum ECC strength is 40
imx6sx -- the BCH's maximum ECC strength is 62
This patch does the following things:
[1] add a new data structure, gpmi_devdata{}, to store the information for
each IP. Besides the IP version, we store the following information:
<1> BCH's maximum ECC strength.
<2> the maximum chain delay in ns used by the EDO mode.
but we may add more information in future.
[2] add the gpmi_devdata_imx{23|28|6q} to replace the gpmi_ids.
[3] simplify the code by using the ECC strength from gpmi_devdata, such as
gpmi_check_ecc() and legacy_set_geometry();
[4] use the maximum chain delay to initialize the EDO mode,
see gpmi_compute_edo_timing().
[5] rewrite the macros, such GPMI_IS_MX{23|28|6Q}.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Add line feed to pr_err.
Signed-off-by: Raphaël Poggi <poggi.raph@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Sub page write doesn't work because of hw issue in controller found on
Keystone SOCs. AEMIF controller is also used on DaVinci SOCs which
don't seems to have any issue. So add "ti,keysone-nand" compatible
to nand driver in order to set NAND_NO_SUBPAGE_WRITE option.
Cc: Warner Losh <imp@bsdimp.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
writeback buffer
mtd_blkdevs is device with volatile cache (writeback buffer), so it should support
REQ_FLUSH to do explicit flush.
Without this patch 'sync' does not guarantee that writeback buffer will be flushed
on disk in case of power off, e.g.:
$ cp some_file /mnt
$ sync
### POWER OFF
In case of this sequence writeback buffer will not be flushed on disk.
This patch fixes this behaviour and explicitly reports to block layer that flush
requests are being supported.
Signed-off-by: Roman Peniaev <r.peniaev@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Now that the index variable is correctly set earlier in this function
we can use it in other places that compute the same thing too.
Signed-off-by: Ron Lee <ron@debian.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Commit 2c9f2365 (mtd: nand: omap: ecc.calculate: merge omap3_calculate_ecc_bch4
in omap_calculate_ecc_bch) introduced minor compile warning
"‘erased_sector_bitflips’ defined but not used [-Wunused-function]" when
compiling without CONFIG_MTD_NAND_OMAP_BCH. Move function
erased_sector_bitflips() into the same ifdef section as the only caller.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
There's no reason this can't be a module. Also, give SPI-NOR its own
submenu.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Many of the serial_flash_cmds.h opcodes are duplicated with spi-nor.h.
Let's begin to unify them.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Begin to unify the differences between serial_flash_cmds.h and
spi-nor.h.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
These are also in serial_flash_cmds.h. (FWIW, I didn't know the C
preprocessor allowed redefinitions without warning like this.)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
I hear that this driver should depend on ARCH_STI, and that "SH" is not
actually a real symbol. At the same time, let's allow compile-testing on
other ARCH'es.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Huang Shijie <b32955@freescale.com>
|
|
serial_flash_cmds.h defines our opcodes a little differently. Let's
borrow its naming, since it's borrowed from the SFDP standard, and it's
more extensible.
This prepares us for merging serial_flash_cmds.h and spi-nor.h opcode
listing.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Huang Shijie <b32955@freescale.com>
|
|
Qualify these with a better namespace, and prepare them for use in more
drivers.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Huang Shijie <b32955@freescale.com>
|
|
Add the copyright information for spi-nor.c and spi-nor.h.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
This patch adds support for the Macronix MX25L3255E device. Unlike the other
Macronix devices we have seen, this device supports WRITE_1_4_4 at reasonable
frequencies. Rather than masking out WRITE_1_4_4 support altogether, we now
rely on the table parameters to indicate whether or not WRITE_1_4_4 should be
used.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Add Spansion S25FL032P to the list of known devices.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
This patch refactors the fsm_read_status() and fsm_write_status() code to
support 1 or 2 byte operations, with a specified command. This allows us to
remove device/register specific code, such as the N25Q fsm_wrvcr() function.
The 'QE' configuration code is updated accordingly, with minor tweaks to ensure
the register values are only written if actually required. One notable change
in this area is that the 'W25Q_STATUS_QE' bit-field is now defined with respect
to the 'SR2' register, rather than the combined 'SR1+SR2' register which is only
used for write operations.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Update the configuration of the Macronix 'QE' bit, such that
we only set or clear the bit if required.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Support for the Macronix 32-bit addressing scheme was originally developed using
the MX25L25635E device. As is often the case, it was found that the presence of
a "WAIT" instruction was required for the "EN4B/EX4B" FSM Sequence to complete.
(It is known that the SPI FSM Controller makes certain undocumented assumptions
regarding what constitutes a valid sequence.) However, further testing
suggested that a small delay was required after issuing the "EX4B" command;
without this delay, data corruptions were observed, consistent with the device
not being ready to retrieve data. Although the issue was not fully understood,
the workaround of adding a small delay was implemented, while awaiting
clarification from Macronix.
The same behaviour has now been found with a second Macronix device, the
MX25L25655E. However, with this device, it seems that the delay is also
required after the 'EN4B' commands. This discovery has prompted us to revisit
the issue.
Although still not conclusive, further tests have suggested that the issue is
down to the SPI FSM Controller, rather than the Macronix devices. Furthermore,
an alternative workaround has emerged which is to set the WAIT time to
0x00000001, rather then 0x00000000. (Note, the WAIT instruction is used purely
for the purpose of achieving "sequence validity", rather than actually
implementing a delay!)
The issue is now being investigated by the Design and Validation teams. In the
meantime, we implement the alternative workaround, which reduces the effective
delay from 1us to 1ns.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Add Macronix MX25L25655E to the list of known devices.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Fix errors like this:
ERROR: "spi_nor_ids" [drivers/mtd/devices/m25p80.ko] undefined!
ERROR: "spi_nor_scan" [drivers/mtd/devices/m25p80.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
(0) What is the QuadSPI controller?
The QuadSPI(Quad Serial Peripheral Interface) acts as an interface to
one single or two external serial flash devices, each with up to 4
bidirectional data lines.
(1) The QuadSPI controller is driven by the LUT(Look-up Table) registers.
The LUT registers are a look-up-table for sequences of instructions.
A valid sequence consists of four LUT registers.
(2) The definition of the LUT register shows below:
---------------------------------------------------
| INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 |
---------------------------------------------------
There are several types of INSTRx, such as:
CMD : the SPI NOR command.
ADDR : the address for the SPI NOR command.
DUMMY : the dummy cycles needed by the SPI NOR command.
....
There are several types of PADx, such as:
PAD1 : use a singe I/O line.
PAD2 : use two I/O lines.
PAD4 : use quad I/O lines.
....
(3) Test this driver with the JFFS2 and UBIFS:
For jffs2:
-------------
#flash_eraseall /dev/mtd0
#mount -t jffs2 /dev/mtdblock0 tmp
#bonnie++ -d tmp -u 0 -s 10 -r 5
For ubifs:
-------------
#flash_eraseall /dev/mtd0
#ubiattach /dev/ubi_ctrl -m 0
#ubimkvol /dev/ubi0 -N test -m
#mount -t ubifs ubi0:test tmp
#bonnie++ -d tmp -u 0 -s 10 -r 5
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Add the spi_nor_match_id() to find the proper spi_device_id with the
NOR flash's name in the spi_nor_ids table.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Use the new SPI nor framework, and rewrite the m25p80:
(0) remove all the NOR comands.
(1) change the m25p->command to an array.
(2) implement the necessary hooks, such as m25p80_read/m25p80_write.
Tested with the m25p32.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
[Brian: rebased]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
This patch cloned most of the m25p80.c. In theory, it adds a new spi-nor layer.
Before this patch, the layer is like:
MTD
------------------------
m25p80
------------------------
spi bus driver
------------------------
SPI NOR chip
After this patch, the layer is like:
MTD
------------------------
spi-nor
------------------------
m25p80
------------------------
spi bus driver
------------------------
SPI NOR chip
With the spi-nor controller driver(Freescale Quadspi), it looks like:
MTD
------------------------
spi-nor
------------------------
fsl-quadspi
------------------------
SPI NOR chip
New APIs:
spi_nor_scan: used to scan a spi-nor flash.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
[Brian: rebased to include additional m25p_ids[] entry]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
This patch fixes I/O errors with the sym53c8xx_2 driver when the disk
returns QUEUE FULL status.
When the controller encounters an error (including QUEUE FULL or BUSY
status), it aborts all not yet submitted requests in the function
sym_dequeue_from_squeue.
This function aborts them with DID_SOFT_ERROR.
If the disk has full tag queue, the request that caused the overflow is
aborted with QUEUE FULL status (and the scsi midlayer properly retries
it until it is accepted by the disk), but the sym53c8xx_2 driver aborts
the following requests with DID_SOFT_ERROR --- for them, the midlayer
does just a few retries and then signals the error up to sd.
The result is that disk returning QUEUE FULL causes request failures.
The error was reproduced on 53c895 with COMPAQ BD03685A24 disk
(rebranded ST336607LC) with command queue 48 or 64 tags. The disk has
64 tags, but under some access patterns it return QUEUE FULL when there
are less than 64 pending tags. The SCSI specification allows returning
QUEUE FULL anytime and it is up to the host to retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull yet more networking updates from David Miller:
1) Various fixes to the new Redpine Signals wireless driver, from
Fariya Fatima.
2) L2TP PPP connect code takes PMTU from the wrong socket, fix from
Dmitry Petukhov.
3) UFO and TSO packets differ in whether they include the protocol
header in gso_size, account for that in skb_gso_transport_seglen().
From Florian Westphal.
4) If VLAN untagging fails, we double free the SKB in the bridging
output path. From Toshiaki Makita.
5) Several call sites of sk->sk_data_ready() were referencing an SKB
just added to the socket receive queue in order to calculate the
second argument via skb->len. This is dangerous because the moment
the skb is added to the receive queue it can be consumed in another
context and freed up.
It turns out also that none of the sk->sk_data_ready()
implementations even care about this second argument.
So just kill it off and thus fix all these use-after-free bugs as a
side effect.
6) Fix inverted test in tcp_v6_send_response(), from Lorenzo Colitti.
7) pktgen needs to do locking properly for LLTX devices, from Daniel
Borkmann.
8) xen-netfront driver initializes TX array entries in RX loop :-) From
Vincenzo Maffione.
9) After refactoring, some tunnel drivers allow a tunnel to be
configured on top itself. Fix from Nicolas Dichtel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
vti: don't allow to add the same tunnel twice
gre: don't allow to add the same tunnel twice
drivers: net: xen-netfront: fix array initialization bug
pktgen: be friendly to LLTX devices
r8152: check RTL8152_UNPLUG
net: sun4i-emac: add promiscuous support
net/apne: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
net: ipv6: Fix oif in TCP SYN+ACK route lookup.
drivers: net: cpsw: enable interrupts after napi enable and clearing previous interrupts
drivers: net: cpsw: discard all packets received when interface is down
net: Fix use after free by removing length arg from sk_data_ready callbacks.
Drivers: net: hyperv: Address UDP checksum issues
Drivers: net: hyperv: Negotiate suitable ndis version for offload support
Drivers: net: hyperv: Allocate memory for all possible per-pecket information
bridge: Fix double free and memory leak around br_allowed_ingress
bonding: Remove debug_fs files when module init fails
i40evf: program RSS LUT correctly
i40evf: remove open-coded skb_cow_head
ixgb: remove open-coded skb_cow_head
igbvf: remove open-coded skb_cow_head
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc
Pull remoteproc cleanups from Ohad Ben-Cohen:
"Several remoteproc cleanup patches coming from Jingoo Han, Julia
Lawall and Uwe Kleine-König"
* tag 'remoteproc-3.15-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
remoteproc/ste_modem: staticize local symbols
remoteproc/davinci: simplify use of devm_ioremap_resource
remoteproc/davinci: drop needless devm_clk_put
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"Here are the target pending updates for v3.15-rc1. Apologies in
advance for waiting until the second to last day of the merge window
to send these out.
The highlights this round include:
- iser-target support for T10 PI (DIF) offloads (Sagi + Or)
- Fix Task Aborted Status (TAS) handling in target-core (Alex Leung)
- Pass in transport supported PI at session initialization (Sagi + MKP + nab)
- Add WRITE_INSERT + READ_STRIP T10 PI support in target-core (nab + Sagi)
- Fix iscsi-target ERL=2 ASYNC_EVENT connection pointer bug (nab)
- Fix tcm_fc use-after-free of ft_tpg (Andy Grover)
- Use correct ib_sg_dma primitives in ib_isert (Mike Marciniszyn)
Also, note the virtio-scsi + vhost-scsi changes to expose T10 PI
metadata into KVM guest have been left-out for now, as there where a
few comments from MST + Paolo that where not able to be addressed in
time for v3.15. Please expect this feature for v3.16-rc1"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (43 commits)
ib_srpt: Use correct ib_sg_dma primitives
target/tcm_fc: Rename ft_tport_create to ft_tport_get
target/tcm_fc: Rename ft_{add,del}_lport to {add,del}_wwn
target/tcm_fc: Rename structs and list members for clarity
target/tcm_fc: Limit to 1 TPG per wwn
target/tcm_fc: Don't export ft_lport_list
target/tcm_fc: Fix use-after-free of ft_tpg
target: Add check to prevent Abort Task from aborting itself
target: Enable READ_STRIP emulation in target_complete_ok_work
target/sbc: Add sbc_dif_read_strip software emulation
target: Enable WRITE_INSERT emulation in target_execute_cmd
target/sbc: Add sbc_dif_generate software emulation
target/sbc: Only expose PI read_cap16 bits when supported by fabric
target/spc: Only expose PI mode page bits when supported by fabric
target/spc: Only expose PI inquiry bits when supported by fabric
target: Pass in transport supported PI at session initialization
target/iblock: Fix double bioset_integrity_free bug
Target/sbc: Initialize COMPARE_AND_WRITE write_sg scatterlist
target/rd: T10-Dif: RAM disk is allocating more space than required.
iscsi-target: Fix ERL=2 ASYNC_EVENT connection pointer bug
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A series of bug fix patches for v3.15-rc1. Most are just driver
fixes. There are some changes at remote controller core level, fixing
some definitions on a new API added for Kernel v3.15.
It also adds the missing include at include/uapi/linux/v4l2-common.h,
to allow its compilation on userspace, as pointed by you"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (24 commits)
[media] gpsca: remove the risk of a division by zero
[media] stk1160: warrant a NUL terminated string
[media] v4l: ti-vpe: retain v4l2_buffer flags for captured buffers
[media] v4l: ti-vpe: Set correct field parameter for output and capture buffers
[media] v4l: ti-vpe: zero out reserved fields in try_fmt
[media] v4l: ti-vpe: Fix initial configuration queue data
[media] v4l: ti-vpe: Use correct bus_info name for the device in querycap
[media] v4l: ti-vpe: report correct capabilities in querycap
[media] v4l: ti-vpe: Allow usage of smaller images
[media] v4l: ti-vpe: Use video_device_release_empty
[media] v4l: ti-vpe: Make sure in job_ready that we have the needed number of dst_bufs
[media] lgdt3305: include sleep functionality in lgdt3304_ops
[media] drx-j: use customise option correctly
[media] m88rs2000: fix sparse static warnings
[media] r820t: fix size and init values
[media] rc-core: remove generic scancode filter
[media] rc-core: split dev->s_filter
[media] rc-core: do not change 32bit NEC scancode format for now
[media] rtl28xxu: remove duplicate ID 0458:707f Genius TVGo DVB-T03
[media] xc2028: add missing break to switch
...
|
|
Pull PCIe non-transparent bridge fixes and features from Jon Mason:
"NTB driver bug fixes to address issues in list traversal, skb leak in
ntb_netdev, a typo, and a leak of msix entries in the error path.
Clean ups of the event handling logic, as well as a overall style
cleanup. Finally, the driver was converted to use the new
pci_enable_msix_range logic (and the refactoring to go along with it)"
* tag 'ntb-3.15' of git://github.com/jonmason/ntb:
ntb: Use pci_enable_msix_range() instead of pci_enable_msix()
ntb: Split ntb_setup_msix() into separate BWD/SNB routines
ntb: Use pci_msix_vec_count() to obtain number of MSI-Xs
NTB: Code Style Clean-up
NTB: client event cleanup
ntb: Fix leakage of ntb_device::msix_entries[] array
NTB: Fix typo in setting one translation register
ntb_netdev: Fix skb free issue in open
ntb_netdev: Fix list_for_each_entry exit issue
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
"The first vfs pile, with deep apologies for being very late in this
window.
Assorted cleanups and fixes, plus a large preparatory part of iov_iter
work. There's a lot more of that, but it'll probably go into the next
merge window - it *does* shape up nicely, removes a lot of
boilerplate, gets rid of locking inconsistencie between aio_write and
splice_write and I hope to get Kent's direct-io rewrite merged into
the same queue, but some of the stuff after this point is having
(mostly trivial) conflicts with the things already merged into
mainline and with some I want more testing.
This one passes LTP and xfstests without regressions, in addition to
usual beating. BTW, readahead02 in ltp syscalls testsuite has started
giving failures since "mm/readahead.c: fix readahead failure for
memoryless NUMA nodes and limit readahead pages" - might be a false
positive, might be a real regression..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
missing bits of "splice: fix racy pipe->buffers uses"
cifs: fix the race in cifs_writev()
ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure
kill generic_file_buffered_write()
ocfs2_file_aio_write(): switch to generic_perform_write()
ceph_aio_write(): switch to generic_perform_write()
xfs_file_buffered_aio_write(): switch to generic_perform_write()
export generic_perform_write(), start getting rid of generic_file_buffer_write()
generic_file_direct_write(): get rid of ppos argument
btrfs_file_aio_write(): get rid of ppos
kill the 5th argument of generic_file_buffered_write()
kill the 4th argument of __generic_file_aio_write()
lustre: don't open-code kernel_recvmsg()
ocfs2: don't open-code kernel_recvmsg()
drbd: don't open-code kernel_recvmsg()
constify blk_rq_map_user_iov() and friends
lustre: switch to kernel_sendmsg()
ocfs2: don't open-code kernel_sendmsg()
take iov_iter stuff to mm/iov_iter.c
process_vm_access: tidy up a bit
...
|
|
This patch fixes the initialization of an array used in the TX
datapath that was mistakenly initialized together with the
RX datapath arrays. An out of range array access could happen
when RX and TX rings had different sizes.
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000, e1000e, igb, igbvf, ixgb, ixgbe,
ixgbevf and i40evf.
Mark fixes an issue with ixgbe and ixgbevf by adding a bit to indicate
when workqueues have been initialized. This permits the register read
error handling from attempting to use them prior to that, which also
generates warnings. Checking for a detected removal after initializing
the work queues allows the probe function to return an error without
getting the workqueue involved. Further, if the error_detected
callback is entered before the workqueues are initialized, exit without
recovery since the device initialization was so truncated.
Francois Romieu provides several patches to all the drivers to remove
the open coded skb_cow_head.
Jakub Kicinski provides a fix for igb where last_rx_timestamp should be
updated only when Rx time stamp is read.
Mitch provides a fix for i40evf where a recent change broke the RSS LUT
programming causing it to be programmed with all 0's.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull audit updates from Eric Paris.
* git://git.infradead.org/users/eparis/audit: (28 commits)
AUDIT: make audit_is_compat depend on CONFIG_AUDIT_COMPAT_GENERIC
audit: renumber AUDIT_FEATURE_CHANGE into the 1300 range
audit: do not cast audit_rule_data pointers pointlesly
AUDIT: Allow login in non-init namespaces
audit: define audit_is_compat in kernel internal header
kernel: Use RCU_INIT_POINTER(x, NULL) in audit.c
sched: declare pid_alive as inline
audit: use uapi/linux/audit.h for AUDIT_ARCH declarations
syscall_get_arch: remove useless function arguments
audit: remove stray newline from audit_log_execve_info() audit_panic() call
audit: remove stray newlines from audit_log_lost messages
audit: include subject in login records
audit: remove superfluous new- prefix in AUDIT_LOGIN messages
audit: allow user processes to log from another PID namespace
audit: anchor all pid references in the initial pid namespace
audit: convert PPIDs to the inital PID namespace.
pid: get pid_t ppid of task in init_pid_ns
audit: rename the misleading audit_get_context() to audit_take_context()
audit: Add generic compat syscall support
audit: Add CONFIG_HAVE_ARCH_AUDITSYSCALL
...
|
|
When the device is unplugged, the driver would try to disable the
device. Add checking the flag of RTL8152_UNPLUG to skip setting
the device when it is unplugged. This could shorten the time of
unloading the driver.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sun4i-emac driver is rather primitive, and doesn't support
promiscuous mode. This makes usage such as bridging impossible,
which is a shame on virtualization capable HW such as the
Allwinner A20.
The fix is fairly simple: move the RX setup code to the ndo_set_rx_mode
vector, and add the required HW configuration when IFF_PROMISC is passed
by the core code.
This has been tested on a generic A20 box running a few virtual
machines hanging off a bridge with the EMAC chip as the link to the
outside world.
Cc: Stefan Roese <sr@denx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes coccinelle error regarding usage of IS_ERR and
PTR_ERR instead of PTR_ERR_OR_ZERO.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/isci
Pull async SCSI resume support from Dan Williams:
"Allow disks and other devices to resume in parallel.
This provides a tangible speed up for a non-esoteric use case (laptop
resume):
https://01.org/suspendresume/blogs/tebrandt/2013/hard-disk-resume-optimization-simpler-approach"
* 'async-scsi-resume' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/isci:
scsi: async sd resume
|
|
Pull md updates from Neil Brown:
"Just a few md patches for the 3.15 merge window.
Not much happening in md/raid at the moment. Just a few bug fixes
(one for -stable) and a couple of performance tweaks"
* tag 'md/3.15' of git://neil.brown.name/md:
raid5: get_active_stripe avoids device_lock
raid5: make_request does less prepare wait
md: avoid oops on unload if some process is in poll or select.
md/raid1: r1buf_pool_alloc: free allocate pages when subsequent allocation fails.
md/bitmap: don't abuse i_writecount for bitmap files.
|
|
Pull NVMe driver updates from Matthew Wilcox:
"Various updates to the NVMe driver. The most user-visible change is
that drive hotplugging now works and CPU hotplug while an NVMe drive
is installed should also work better"
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Retry failed commands with non-fatal errors
NVMe: Add getgeo to block ops
NVMe: Start-stop nvme_thread during device add-remove.
NVMe: Make I/O timeout a module parameter
NVMe: CPU hot plug notification
NVMe: per-cpu io queues
NVMe: Replace DEFINE_PCI_DEVICE_TABLE
NVMe: Fix divide-by-zero in nvme_trans_io_get_num_cmds
NVMe: IOCTL path RCU protect queue access
NVMe: RCU protected access to io queues
NVMe: Initialize device reference count earlier
NVMe: Add CONFIG_PM_SLEEP to suspend/resume functions
|
