| Age | Commit message (Collapse) | Author |
|---|
|
It's possible for VMs with older versions of bnx2x to run over a hypervisor
with latest driver. If a VF in such a VM does not support RSS configuration,
the PF driver in the hypervisor will print an error message to system logs.
This changes the error message into a debug message, as this is very likely
a false alarm for an older VF (i.e., VF manages to work properly; PF simply
cannot configure the additional queues for it).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's a known issue that using `ethtool -e' flips the endianity of the
written data, i.e., using `ethtool -E' to dump eeprom image and than using
`ethtool -e' to re-write that same image will result in an image where
the data has the opposite endianity.
Sadly, this cannot be fixed as there are already various tools deployed
based on the endianity of the eeprom read/write.
Instead, a comment is added to the code to help explain why this is un-fixable.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function adds several OS calls required to fully enable PCIe AER support -
pci_enable_pcie_error_reporting() and pci_cleanup_aer_uncorrect_error_status().
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the ability for bnx2x to load after UNDI is used in the
preboot environment on a multi-function interface which is not the first
interface of a given device.
Notice a side-effect is that the order by which the functions are probed and
thus interfaces appear might change, as this patch utilizes the EPROBE_DEFER
return value (and mechanism).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal or
ether_addr_equal_unaligned instead of memcmp.
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal_unaligned
instead of memcmp.
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal
instead of memcmp.
Cc: Bing Zhao <bzhao@marvell.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal
instead of memcmp.
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal
instead of memcmp.
Cc: Solomon Peachy <pizza@shaftnet.org>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal
instead of memcmp.
Cc: Jouni Malinen <j@w1.fi>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal
instead of memcmp.
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal
instead of memcmp.
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal
instead of memcmp.
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Cc: linux-atm-general@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Faisal Latif <faisal.latif@intel.com>
Cc: linux-rdma@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal
instead of memcmp.
Cc: Rupesh Gujare <rupesh.gujare@atmel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: devel@driverdev.osuosl.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal
instead of memcmp.
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Michal Ostrowski <mostrows@earthlink.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Joerg Reuter <jreuter@yaina.de>
Cc: linux-hams@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the recently added and possibly more efficient
ether_addr_equal_unaligned to instead of memcmp.
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Don Fry <pcnet32@frontier.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function did not be used any more, so remove it.
Cc: Li Yang <leoli@freescale.com>
Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use it or lose it.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cleanup by making local functions static.
The code to load config file is unreachable in net-next, probably came
from some out of tree driver.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When adding a new vxlan device to an "underlying carrier" (here:
dst->remote_ifindex), the MTU size assigned to the vxlan device
is the MTU at setup time of the carrier - needed headroom, when
adding a vxlan device w/o explicit carrier, then it defaults
to 1500.
In case of an explicit carrier that supports jumbo frames, we
currently cannot change vxlan MTU via ip(8) to > 1500 in
post-setup time, as vxlan driver uses eth_change_mtu() as default
method for manually setting MTU.
Hence, use a custom implementation that only falls back to
eth_change_mtu() in case we didn't use a dev parameter on device
setup time, and otherwise allow a max MTU setting of the carrier
incl. adjustment for headroom.
Reported-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
OMAP's ti_hecc driver is used to support the CAN controller on many omap2plus
SoCs (OMAP2430, OMAP3, OMAP4, OMAP5 and AM335x), so it's wrong to make this
depend on OMAP3 only. Take an extra step, to get wider build coverage, and make
the driver depend on ARM.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds Device Tree support to the Microchip MCP251X driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The ADM6996L switch and some Broadcom switches with two MII interfaces
like the BCM5325F connected to two MACs on the SoC, used on some
routers do not return a valid value when reading the PHY id register
and Linux thinks there is no PHY at all, but that is wrong.
This patch registers a fixed phy in the arch code and then searches it
when there is no other phy in the Ethernet driver code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
b44_phy_reset() will fail for an external PHY and only work with the
internal PHY, this was an old workaround when the detection of an
external switch based on the PHY address failed and it is not needed
any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this patch we can not access the PHY when the MAC is switched
off. This PHY access is needed to configure the switch, which is done
through PHY registers.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the older home routers based on the Broadcom BCM47XX SoC series
are using a MAC that is supported by b44. On most of these routers not
the internal PHY of this MAC core is used, but a switch sometimes on an
external chip or integrated into the same SoC as the Ethernet core.
For this switch a special PHY driver is needed which should not be
integrated into b44 as the same switches are also used by other
Broadcom home networking SoCs which are using different Ethernet MAC
drivers. This was tested with the b53 switch driver which is currently
on its way to mainline.
If the internal PHY is not used, b44 will now search on the MDIO bus
for a phy and use the Linux phylib subsystem to register a driver.
Support for the internal PHY must stay here, because there are some
device which are suing the internal phy.
With this patch we scan the mdio bus when the sprom or nvram says that
the PHY address is 30, if a PHY was found at this address b44 uses it.
This was tested with a BCM4704, BCM4712 and BCM5354.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patch will add these functions for phylib, and we should
rename the old ones before. This now indicates that these functions are
used for the mdio registers and on the mii interface.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the phy address is 31, this means that there is no PHY connected
to this MAC at all, no internal and no external PHY. Reading these PHY
registers causes a system reset on some routers.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY address 30 means there is no local PHY, but there could be an
external PHY like a switch connected via MII. This is the case on most
embedded home routers where this driver is used.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Ethernet core supported by b44 supports an internal PHY integrated
into the mac core, which is supported by the b44 driver and an external
PHY to which the mac core is connected. This external PHY could be a
switch connected through MII, which is often the case when this core is
used on home routers. The usage of an external PHY was assumed when the
PHY address 30 was used and an internal PHY was assumed when the PHY
address was different. To verify that b44_phy_reset() was called and
checked if it worked, otherwise PHY address 30 was assumed, an external
PHY. It is better to check the register which says which PHY is
connected to the MAC instead of checking the PHY address.
The interface to an external PHY was only activated when this register
was set.
This also changes B44_FLAG_INTERNAL_PHY to B44_FLAG_EXTERNAL_PHY, it is
easier to check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Save pkt_hash_types in tpa structure.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's no need anymore to call phy_init_hw() to reset/resume the PHY from the
driver, as the call chain in phylib already has reached it, and so reset/resumed
the PHY (even resuming it twice). This duplicate reset is not only needless, it
e.g. clears the PHY's interrupt enables just setup by phylib and so prevents the
expected IRQs from the PHY.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow the platform code to pass PHY's IRQ to the driver. Print this IRQ along
with the other PHY datails in sh_eth_phy_init().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to validate port number at mlx4_promisc_qp() before use.
Since port number is extracted from gid, as a cooked or corrupted gid
could lead to a crash.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add NAPI for TX side,
implement its support and provide NAPI callback.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MLX4_DEV_EVENT_SLAVE_INIT and MLX4_DEV_EVENT_SLAVE_SHUTDOWN
events used by Hypervisor to inform the PPF IB driver that
IB para-virtualization must be initialized/destroyed for a slave.
If this event is catched by ETH VF annoying but harmless error message
is printed into dmesg. Remove dmesg prints for these events.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To achieve out of the box performance default is to use 64 byte CQE/EQE.
In tests that we conduct in our labs, we achieved a performance
improvement of twice the message rate. For older VF/libmlx4 support,
enable_64b_cqe_eqe must be set to 0 (disabled).
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only TX rings of User Piority 0 are mapped.
TX rings of other UP's are using UP 0 mapping.
XPS is not in use when num_tc is set.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the port GUID read from the firmware to identify the physical port.
This port identifier is available via ndo_get_phys_port_id for both PF
and VF net-devices.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the infrastructure needed to support ndo_get_phys_port_id which
allows users to identify to which physical port a net-device is connected
to by reading a unique port id.
This will work for VFs and PFs.
The driver uses a new device capability - phys_port_id, The PF driver
reads the port phys_port_id from Firmware and stores it. The VF driver
reads the port phys_port_id from the PF using QUERY_FUNC_CAP command.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set nic_info field in QUERY_FUNC_CAP, which designates
supplementary NIC information is provided by the hypervisor.
When set, the following fields are valid: nic_num_rings,
nic_indirection_tbl_sz, cur_mac and phys_port_id.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use correct names for QUERY_FUNC_CAP fields: flags0 and flags1.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All mailboxes are already zeroed by commit:
571b8b9 net/mlx4_core: Initialize all mailbox buffers to zero before use
Remove explicit zero set for force mac and force vlan fields in
mlx4_QUERY_FUNC_CAP_wrapper
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch marks the function il_clear_traffic_stats() in debug.c as
static because they are not used outside this file.
Thus, it also removes the following warnings in
wireless/iwlegacy/debug.c:
drivers/net/wireless/iwlegacy/debug.c:35:1: warning: no previous prototype for ‘il_clear_traffic_stats’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch marks the function il4965_ucode_rx_stats_read(),
il4965_ucode_tx_stats_read() and il4965_ucode_general_stats_read() in
4965-debug.c as static because they are not used outside this file.
Thus, it also removes the following warnings in
wireless/iwlegacy/4965-debug.c:
drivers/net/wireless/iwlegacy/4965-debug.c:59:1: warning: no previous prototype for ‘il4965_ucode_rx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/4965-debug.c:471:1: warning: no previous prototype for ‘il4965_ucode_tx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/4965-debug.c:637:1: warning: no previous prototype for ‘il4965_ucode_general_stats_read’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
