| Age | Commit message (Collapse) | Author |
|---|
|
packets)
Fix Ethernet communication bug(dupliated and lost packets)
in RMII PHY mode- dont call mac_disable and mac_enable during
10/100 REFCLK changes - mac_enable screws up the DMA descriptor chain
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add device ID for the ADMtek ADM8515 USB NIC to the DM9601 driver.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'alpm' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] AHCI: add hw link power management support
[libata] Link power management infrastructure
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] AHCI: fix newly introduced host-reset bug
[libata] sata_nv: fix SWNCQ enabling
libata: add MAXTOR 7V300F0/VA111900 to NCQ blacklist
libata: no need to speed down if already at PIO0
libata: relocate forcing PIO0 on reset
pata_ns87415: define SUPERIO_IDE_MAX_RETRIES
[libata] Address some checkpatch-spotted issues
[libata] fix 'if(' and similar areas that lack whitespace
libata: implement ata_wait_after_reset()
libata: track SLEEP state and issue SRST to wake it up
libata: relocate and fix post-command processing
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (22 commits)
Fix ethernet multicast for ucc_geth.
netdrvr/pcmcia: use IRQ_TYPE_DYNAMIC_SHARING flag for irq.Attributes.
FEC - fast ethernet controller for mpc52xx
ehea: add kexec support
e1000e: Remove legacy jumbo frame receive code
e1000e: Re-enable SECRC - crc stripping
e1000e: Fix PBA calculation for jumbo frame packets
e1000e: Fix jumbo frame receive code.
drivers/net/irda/au1k_ir: fix obvious irq handler bugs
ipg: Kconfig whitepaces/tab damages
ipg: missing Kconfig dependency
r8169: remove poll_locked logic
r8169: napi config
[PATCH] iwl3945: fix direct scan problem
[PATCH] iwl3945: cancel scan on rxon command
[PATCH] iwl4965: fix scan problem
[PATCH] iwl4965: fix driver hang related to hardware scan
[PATCH] iwlwifi: fix sending probe request in iwl 4965
[PATCH] rtl8187: Allow multicast frames
[PATCH] b43/b43legacy: jiffies_round -> jiffies_round_relative
...
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6
* 'warnings-upstream' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
[ISDN] capidrv: address two longstanding warnings
|
|
This patch will set the correct bits to turn on Aggressive
Link Power Management (ALPM) for the ahci driver. This
will cause the controller and disk to negotiate a lower
power state for the link when there is no activity (see
the AHCI 1.x spec for details). This feature is mutually
exclusive with Hot Plug, so when ALPM is enabled, Hot Plug
is disabled. ALPM will be enabled by default, but it is
settable via the scsi host syfs interface. Possible
settings for this feature are:
Setting Effect
----------------------------------------------------------
min_power ALPM is enabled, and link set to enter
lowest power state (SLUMBER) when idle
Hot plug not allowed.
max_performance ALPM is disabled, Hot Plug is allowed
medium_power ALPM is enabled, and link set to enter
second lowest power state (PARTIAL) when
idle. Hot plug not allowed.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Device Initiated Power Management, which is defined
in SATA 2.5 can be enabled for disks which support it.
This patch enables DIPM when the user sets the link
power management policy to "min_power".
Additionally, libata drivers can define a function
(enable_pm) that will perform hardware specific actions to
enable whatever power management policy the user set up
for Host Initiated Power management (HIPM).
This power management policy will be activated after all
disks have been enumerated and intialized. Drivers should
also define disable_pm, which will turn off link power
management, but not change link power management policy.
Documentation/scsi/link_power_management_policy.txt has additional
information.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
compat_ioctl: fix block device compat ioctl regression
[BLOCK] Fix bad sharing of tag busy list on queues with shared tag maps
Fix a build error when BLOCK=n
block: use lock bitops for the tag map.
cciss: update copyright notices
cfq_get_queue: fix possible NULL pointer access
blk_sync_queue() should cancel request_queue->unplug_work
cfq_exit_queue() should cancel cfq_data->unplug_work
block layer: remove a unused argument of drive_stat_acct()
|
|
* 'sg' of git://git.kernel.dk/linux-2.6-block:
Correction of "Update drivers to use sg helpers" patch for IMXMMC driver
sg_init_table() should use unsigned loop index variable
sg_last() should use unsigned loop index variable
Initialise scatter/gather list in sg driver
Initialise scatter/gather list in ata_sg_setup
x86: fix pci-gart failure handling
SG: s390-scsi: missing size parameter in zfcp_address_to_sg()
SG: clear termination bit in sg_chain()
|
|
The recent fix to host reset introduced a problem, whereby AHCI-enable
bit would be cleared upon reset, if it was not asserted prior to reset.
Unconditionally enable AHCI-enable bit.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
a) for type B we should _not_ iounmap() acb->pmu; it's not ioremapped.
b) for type B we should iounmap() two regions we _do_ ioremap.
c) if ioremap() fails, we need to bail out (and clean up).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use of ptrdiff_t in places like
- if (!access_ok(VERIFY_WRITE, u_tmp->rx_buf, u_tmp->len))
+ if (!access_ok(VERIFY_WRITE, (u8 __user *)
+ (ptrdiff_t) u_tmp->rx_buf,
+ u_tmp->len))
is wrong; for one thing, it's a bad C (it's what uintptr_t is for; in general
we are not even promised that ptrdiff_t is large enough to hold a pointer,
just enough to hold a difference between two pointers within the same object).
For another, it confuses the fsck out of sparse.
Use unsigned long or uintptr_t instead. There are several places misusing
ptrdiff_t; fixed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
doh...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
initializing a field in data shared with the card with
cpu_to_le32(something) | 0x100000 is broken - the field is, indeed,
little-endian and we need cpu_to_le32() on both parts.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
driver still has serious portability problems
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- off by one in dmar_get_fault_reason() (maximal index in array is
ARRAY_SIZE()-1, not ARRAY_SIZE())
- NULL noise removal
- __iomem annotation fix
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Don't undef __i386__/__x86_64__ in uml anymore, make sure that (few) places
that required adjusting the ifdefs got those.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Adapted from patches by Kuan Lou @ NVIDIA and Bartlomiej Zolnierkiewicz.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch updates the copyright information for the cciss driver. It
includes extending the year to 2007 (how timely) and some minor corrections
deemed necessary by HP legal and the Open Source Review Board. Please
consider this patch for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
--------------------------------------------------------------------------------
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
MAXTOR 7V300F0/VA111900 does spurious NCQ completions. Add it to
blacklist. This problem is reported by Carsten Otto.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Carsten Otto <c-otto@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
After reset, transfer mode is always PIO0 regardless of
dev->xfer_mask. Check dev->pio_mode before trying to slow down after
configuration failure. This prevents bogus speed down before device
is actually configured.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Forcing PIO0 on reset was done inside ata_bus_softreset(), which is a
bit out of place as it should be applied to all resets - hard, soft
and implementation which don't use ata_bus_softreset(). Relocate it
such that...
* For new EH, it's done in ata_eh_reset() before calling prereset.
* For old EH, it's done before calling ap->ops->phy_reset() in
ata_bus_probe().
This makes PIO0 forced after all resets. Another difference is that
reset itself is done after PIO0 is forced.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Code copied from drivers/ide/pci/ns87415.c uses this, so copy the
definition from there as well.
Fixes the following build error:
CC [M] drivers/ata/pata_ns87415.o
drivers/ata/pata_ns87415.c: In function ‘ns87560_read_buggy’:
drivers/ata/pata_ns87415.c:228: error: ‘SUPERIO_IDE_MAX_RETRIES’ undeclared (first use in this function)
drivers/ata/pata_ns87415.c:228: error: (Each undeclared identifier is reported only once
drivers/ata/pata_ns87415.c:228: error: for each function it appears in.)
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
On certain device/controller combination, 0xff status is asserted
after reset and doesn't get cleared during 150ms post-reset wait. As
0xff status is interpreted as no device (for good reasons), this can
lead to misdetection on such cases.
This patch implements ata_wait_after_reset() which replaces the 150ms
sleep and waits upto ATA_TMOUT_FF_WAIT if status is 0xff.
ATA_TMOUT_FF_WAIT is currently 800ms which is enough for
HHD424020F7SV00 to get detected but not enough for Quantum GoVault
drive which is known to take upto 2s.
Without parallel probing, spending 2s on 0xff port would incur too
much delay on ata_piix's which use 0xff to indicate empty port and
doesn't have SCR register, so GoVault needs to wait till parallel
probing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
ATA devices in SLEEP mode don't respond to any commands. SRST is
necessary to wake it up. Till now, when a command is issued to a
device in SLEEP mode, the command times out, which makes EH reset the
device and retry the command after that, causing a long delay.
This patch makes libata track SLEEP state and issue SRST automatically
if a command is about to be issued to a device in SLEEP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bruce Allen <ballen@gravity.phys.uwm.edu>
Cc: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Some commands need post-processing after successful completion. This
was done in ata_scsi_qc_complete() till now but this has the following
problems.
* Post-command processing gets executed when qc is completed from EH.
Some qc's are retried from EH with zero err_mask and thus triggers
unnecessary/incorrect post-command processing.
* Command post processing doesn't belong to SAT layer.
* Link-wide revalidation was scheduled where device revalidation
suffices.
This patch moves post-command processing to success completion path of
ata_qc_complete() which is travelled iff the command is going to be
completed without passing through EH and updates post-command
processing such that device-specific action is used. While at it,
restructure code a bit for readability.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
hw_add_addr_in_hash() already swaps byte
order, don't do it in ucc_geth_set_multi() too.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: ucc_geth maintainer
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The drivers below support IRQ-sharing.
3c574_cs, 3c589_cs, pcnet_cs,
axnet_cs, smc91c92_cs, fmvj18x_cs.
xirc2ps_cs, serial_cs.
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Driver for ethernet on mpc5200/mpc5200b SoCs (FEC).
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/romieu/netdev-2.6 into upstream-fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes
|
|
eHEA resources that are allocated via H_CALLs have a unique identifier each.
These identifiers are necessary to free the resources. A reboot notifier
is used to free all eHEA resources before the indentifiers get lost, i.e
before kexec starts a new kernel.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The legacy jumbo frame receive code is no longer needed since all
hardware can do packet split and we're no longer offering a bypass
kernel config option to disable packet split. Remove the unused code.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This workaround code performed software stripping instead of the
hardware which can do it much faster. None of the e1000e target
hardware has issues with this feature and should work fine. This
gives us some performance back on receive, and removes some
kludging stripping the 4 bytes.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Upon inspection the rx FIFO size calculation code was found to have
2 significant flaws: A superfluous minus sign resulting in the
wrong size to be used for jumbo frames on 82573 and ich9, as well
as that this code rewrote the read-only adapter->pba variable
resulting in different values at each run.
Without this patch jumbo's will work but performance will be
awkward since the TX size is not adequate for two whole frames.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix allocation and freeing of jumbo frames where several bugs
were recently introduced by cleanups after we forked this code
from e1000. This moves ps_pages to buffer_info where it really
belongs and makes it a dynamically allocated array. The penalty
is not that high since it's allocated outside of the buffer_info
struct anyway.
Without this patch all jumbo frames are completely broken and the
driver panics.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
interrupt handlers return a return value these days.
Also, kill always-true test and unneeded void* cast.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* change #warning to a code comment
* add comment and special ifdef'd 64-bit code for a situation where
we must store a pointer into a CAPI field 'Data', which is fixed by
the interface at 32 bits.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Karsten Keil <kkeil@suse.de>
|
|
The previous change omits "data->" prefix
in the "data->sg" case. This change fixes kernel
compilation.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
drivers/mmc/host/imxmmc.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
|
|
After turning on DEBUG_SG I hit a fail:
kernel BUG at include/linux/scatterlist.h:50!
sg_build_indirect
sg_build_reserve
sg_open
chrdev_open
__dentry_open
do_filp_open
do_sys_open
We should initialise the sg list when we allocate it in sg_build_sgat.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
After turning on DEBUG_SG I hit a fail:
kernel BUG at include/linux/scatterlist.h:50!
ata_qc_issue
ata_scsi_translate
ipr_queuecommand
scsi_dispatch_cmd
scsi_request_fn
elv_insert
blk_execute_rq_nowait
blk_execute_rq
sg_io
scsi_cmd_ioctl
cdrom_ioctl
sr_block_ioctl
blkdev_driver_ioctl
blkdev_ioctl
block_ioctl
do_ioctl
vfs_ioctl
sys_ioctl
sg_ioctl_trans
It looks like ata_sg_setup is working on an uninitialised sg table. Call
sg_init_table to initialise it before use.
Signed-off-by: Anton Blanchard <anton@samba.org>
Note: this patch will fix it, but you could also get away with just
doing the sg_init_table() once at qc creation time.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: add SH-S202J to ivb_list[]
drivers/ide/pci/sc1200.c: fix suspend/resume buglets and warnings
drivers/ide/pci/generic: fix build for CONFIG_HOTPLUG=n
hpt366: fix build for CONFIG_HOTPLUG=n
cy82c693: fix build for CONFIG_HOTPLUG=n
|
|
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Avuton Olrich <avuton@gmail.com>
Cc: Jesse Huang <jesse@icplus.com.tw>
Cc: Sorbica Shieh <sorbica@icplus.com.tw>
|
|
Fix for the error below while linking vmlinux:
[...]
drivers/built-in.o: In function `ipg_ioctl':
drivers/net/ipg.c:2148: undefined reference to `generic_mii_ioctl'
drivers/built-in.o: In function `ipg_get_settings':
drivers/net/ipg.c:2181: undefined reference to `mii_ethtool_gset'
drivers/built-in.o: In function `ipg_set_settings':
drivers/net/ipg.c:2193: undefined reference to `mii_ethtool_sset'
drivers/built-in.o: In function `ipg_nway_reset':
drivers/net/ipg.c:2205: undefined reference to `mii_nway_restart'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Avuton Olrich <avuton@gmail.com>
Cc: Jesse Huang <jesse@icplus.com.tw>
Cc: Sorbica Shieh <sorbica@icplus.com.tw>
|
|
Disabling napi polling early is well enough.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
|
|
Don't call napi_disable if not configured and make sure that any
misuse of napi_xxx in future fails with a compile error.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
|
