| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"A couple of bug fixes, a debug change for qdio, an update for the
default config, and one small extension.
The watchdog module based on diagnose 0x288 is converted to the
watchdog API and it now works under LPAR as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ccwgroup: use ccwgroup_ungroup wrapper
s390/ccwgroup: fix an uninitialized return code
s390/ccwgroup: obtain extra reference for asynchronous processing
qdio: Keep device-specific dbf entries
s390/compat: correct ucontext layout for high gprs
s390/cio: set device name as early as possible
s390: update default configuration
s390: avoid format strings leaking into names
s390/airq: silence lockdep warning
s390/watchdog: add support for LPAR operation (diag288)
s390/watchdog: use watchdog API
s390/sclp_vt220: Enable ASCII console per default
s390/qdio: replace shift loop by ilog2
s390/cio: silence lockdep warning
s390/uaccess: always load the kernel ASCE after task switch
s390/ap_bus: Make modules parameters visible in sysfs
|
|
Pull UniCore32 bug fixes from Guan Xuetao:
"This includes bugfixes to make unicore32 successfully build under
defconfig, and some changes for allmodconfig (though not finished)"
* tag 'for-linus' of git://github.com/gxt/linux:
unicore32: Remove ARCH_HAS_CPUFREQ config option
UniCore32: Change git tree location information in MAINTAINERS
arch: unicore32: ksyms: export '__cpuc_coherent_kern_range' to avoid compiling failure
arch: unicore32: ksyms: export 'pm_power_off' to avoid compiling failure.
arch: unicore32: ksyms: export additional find_first_*() to avoid compiling failure
arch:unicore32:mm: add devmem_is_allowed() to support STRICT_DEVMEM
unicore32: include: asm: add missing ')' for PAGE_* macros in pgtable.h
arch/unicore32/kernel/setup.c: add generic 'screen_info' to avoid compiling failure
drivers: scsi: mvsas: fix compiling issue by adding 'MVS_' for "enum pci_interrupt_cause"
arch: unicore32: kernel: ksyms: remove 'bswapsi2' and 'muldi3' to avoid compiling failure
arch/unicore32/kernel/ksyms.c: remove 2 export symbols to avoid compiling failure
drivers/rtc/rtc-puv3.c: remove "&dev->" for typo issue MIME-Version: 1.0
drivers/rtc/rtc-puv3.c: use dev_dbg() instead of dev_debug() for typo issue
arch/unicore32/include/asm/io.h: add readl_relaxed() generic definition
arch/unicore32/include/asm/ptrace.h: add generic definition for profile_pc()
arch/unicore32/mm/alignment.c: include "asm/pgtable.h" to avoid compiling error
arch/unicore32/kernel/clock.c: add readl() and writel() for 'PM_' macros
arch/unicore32/kernel/module.c: use __vmalloc_node_range() instead of __vmalloc_area()
arch/unicore32/kernel/ksyms.c: remove several undefined exported symbols
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver fixes from Greg KH:
"Here are 3 patches, one a revert of the UIO patch you objected to in
3.16-rc1 and that no one wanted to defend, a w1 driver bugfix, and a
MAINTAINERS update for the vmware balloon driver.
All of these, except for the MAINTAINERS update which just got added,
have been in linux-next just fine"
* tag 'char-misc-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: add entry for VMware Balloon driver
w1: mxc_w1: Fix incorrect "presence" status
Revert "uio: fix vma io range check in mmap"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a few fixes for staging and iio drivers that resolve issues
reported in 3.16-rc1.
All have been in linux-next just fine"
* tag 'staging-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
imx-drm: parallel-display: Fix DPMS default state.
staging: android: timed_output: fix use after free of dev
staging: comedi: addi_apci_1564: add addi_watchdog dependency
staging: rtl8723au: Reference correct firmwarefiles with MODULE_FIRMWARE()
staging: rtl8723au: Request correct firmware file for A-cut parts
iio: adc: checking for NULL instead of IS_ERR() in probe
iio: adc: at91: signedness bug in at91_adc_get_trigger_value_by_name()
iio: mxs-lradc: fix divider
iio: Fix endianness issue in ak8975_read_axis()
staging/iio: IIO_SIMPLE_DUMMY_BUFFER neds IIO_BUFFER
twl4030-madc: Request processed values in twl4030_get_madc_conversion
staging: iio: tsl2x7x_core: fix proximity treshold
iio: Fix two mpl3115 issues in measurement conversion
iio: hid-sensors: Get feature report from sensor hub after changing power state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial bugfixes from Greg KH:
"Here are some tty / serial driver bugfixes for 3.16-rc2 that resolve
some reported issues. The samsung driver build error itself has been
reported by a bunch of people, sorry about that one. The others are
all tiny and everyone seems to like them in linux-next so far"
* tag 'tty-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty/serial: fix 8250 early console option passing to regular console
tty: Correct INPCK handling
serial: Fix IGNBRK handling
serial: samsung: Fix build error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.16-rc2 that resolve some reported
issues. All of these have been in linux-next for a while with no
problems"
* tag 'usb-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: usbtest: add a timeout for scatter-gather tests
USB: EHCI: avoid BIOS handover on the HASEE E200
usb: fix hub-port pm_runtime_enable() vs runtime pm transitions
usb: quiet peer failure warning, disable poweroff
usb: improve "not suspended yet" message in hub_suspend()
xhci: Fix sleeping with IRQs disabled in xhci_stop_device()
usb: fix ->update_hub_device() vs hdev->maxchild
|
|
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are fixes mostly (ia64 regression related to the ACPI
enumeration of devices, cpufreq regressions, fix for I2C controllers
included in Intel SoCs, mvebu cpuidle driver fix related to sysfs)
plus additional kernel command line arguments from Kees to make it
possible to build kernel images with hibernation and the kernel
address space randomization included simultaneously, a new ACPI
battery driver quirk for a system with a broken BIOS and a couple of
ACPI core cleanups.
Specifics:
- Fix for an ia64 regression introduced during the 3.11 cycle by a
commit that modified the hardware initialization ordering and made
device discovery fail on some systems.
- Fix for a build problem on systems where the cpufreq-cpu0 driver is
built-in and the cpu-thermal driver is modular from Arnd Bergmann.
- Fix for a recently introduced computational mistake in the
intel_pstate driver that leads to excessive rounding errors from
Doug Smythies.
- Fix for a failure code path in cpufreq_update_policy() that fails
to unlock the locks acquired previously from Aaron Plattner.
- Fix for the cpuidle mvebu driver to use shorter state names which
will prevent the sysfs interface from returning mangled strings.
From Gregory Clement.
- ACPI LPSS driver fix to make sure that the I2C controllers included
in BayTrail SoCs are not held in the reset state while they are
being probed from Mika Westerberg.
- New kernel command line arguments making it possible to build
kernel images with hibernation and kASLR included at the same time
and to select which of them will be used via the command line (they
are still functionally mutually exclusive, though). From Kees
Cook.
- ACPI battery driver quirk for Acer Aspire V5-573G that fails to
send battery status change notifications timely from Alexander
Mezin.
- Two ACPI core cleanups from Christoph Jaeger and Fabian Frederick"
* tag 'pm+acpi-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: mvebu: Fix the name of the states
cpufreq: unlock when failing cpufreq_update_policy()
intel_pstate: Correct rounding in busy calculation
ACPI: use kstrto*() instead of simple_strto*()
ACPI / processor replace __attribute__((packed)) by __packed
ACPI / battery: add quirk for Acer Aspire V5-573G
ACPI / battery: use callback for setting up quirks
ACPI / LPSS: Take I2C host controllers out of reset
x86, kaslr: boot-time selectable with hibernation
PM / hibernate: introduce "nohibernate" boot parameter
cpufreq: cpufreq-cpu0: fix CPU_THERMAL dependency
ACPI / ia64 / sba_iommu: Restore the working initialization ordering
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The significant part here is a few security fixes for ALSA core
control API by Lars. Besides that, there are a few fixes for ASoC
sigmadsp (again by Lars) for building properly, and small fixes for
ASoC rsnd, MMP, PXA and FSL, in addition to a fix for bogus WARNING in
i915/HD-audio binding"
* tag 'sound-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: control: Make sure that id->index does not overflow
ALSA: control: Handle numid overflow
ALSA: control: Don't access controls outside of protected regions
ALSA: control: Fix replacing user controls
ALSA: control: Protect user controls against concurrent access
drm/i915, HD-audio: Don't continue probing when nomodeset is given
ASoC: fsl: Fix build problem
ASoC: rsnd: fixup index of src/dst mod when capture
ASoC: fsl_spdif: Fix integer overflow when calculating divisors
ASoC: fsl_spdif: Fix incorrect usage of regmap_read()
ASoC: dapm: Make sure register value is in sync with DAPM kcontrol state
ASoC: sigmadsp: Split regmap and I2C support into separate modules
ASoC: MMP audio needs sram support
ASoC: pxa: add I2C dependencies as needed
|
|
Pull drm fixes from Dave Airlie:
"This looks bigger than it is, as one of the nouveau firmware fixes
("drm/gf100-/gr: report class data to host on fwmthd failure")
regenerates a bunch of the firmware files after changing the assembly
by a few lines, without that, its more of a
36 files changed, 370 insertions(+), 129 deletions(-)
It contains some vt.c fixes acked by Greg, for rare hard hangs on i915
loading, that also fixes hangs on reload and spurious register write
errors.
drm core: one fix for uninit memory
nouveau: displayport rework caused a few regressions, Ben has been
fixing them as the appear, along with some other fixes
radeon: pageflipping regression fix, deep color fix, mode validation
fixes
i915: fbc disable, vga console kick off, backlight fix, divide-by-zero
fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits)
drm: fix uninitialized acquire_ctx fields (v2)
drm/radeon: Fix radeon_irq_kms_pflip_irq_get/put() imbalance
Revert "drm/radeon: remove drm_vblank_get|put from pflip handling"
drm/radeon: improve dvi_mode_valid
drm/radeon: update mode_valid testing for DP
drm/radeon: Use dce5/6 hdmi deep color clock setup also on dce8+
drm/nouveau/disp: fix oops in destructor with headless cards
drm/gf117/i2c: no aux channels on this chipset
drm/nouveau/doc: update the thermal documentation
drm/nouveau/pwr: fix typo in fifo wrap handling
drm/nv50/disp: fix a potential oops in supervisor handling
drm/nouveau/disp/dp: don't touch link config after success
drm/nouveau/kms: reference vblank for crtc during pageflip.
drm/gk104/fb/ram: fixups from an earlier search+replace
drm/nv50/gr: remove an unneeded write while initialising PGRAPH
drm/nv50/gr: fix overlap while zeroing zcull regions
drm/gf100-/gr: report class data to host on fwmthd failure
drm/gk104/ibus: increase various random timeouts
drm/gk104/clk: only touch divider for mode we'll be using
drm/radeon: Bypass hw lut's for > 8 bpc framebuffer scanout.
...
|
|
Pull block fixes from Jens Axboe:
"A smaller collection of fixes for the block core that would be nice to
have in -rc2. This pull request contains:
- Fixes for races in the wait/wakeup logic used in blk-mq from
Alexander. No issues have been observed, but it is definitely a
bit flakey currently. Alternatively, we may drop the cyclic
wakeups going forward, but that needs more testing.
- Some cleanups from Christoph.
- Fix for an oops in null_blk if queue_mode=1 and softirq completions
are used. From me.
- A fix for a regression caused by the chunk size setting. It
inadvertently used max_hw_sectors instead of max_sectors, which is
incorrect, and causes hangs on btrfs multi-disk setups (where hw
sectors apparently isn't set). From me.
- Removal of WQ_POWER_EFFICIENT in the kblockd creation. This was a
recent addition as well, but it actually breaks blk-mq which relies
on strict scheduling. If the workqueue power_efficient mode is
turned on, this breaks blk-mq. From Matias.
- null_blk module parameter description fix from Mike"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: bitmap tag: fix races in bt_get() function
blk-mq: bitmap tag: fix race on blk_mq_bitmap_tags::wake_cnt
blk-mq: bitmap tag: fix races on shared ::wake_index fields
block: blk_max_size_offset() should check ->max_sectors
null_blk: fix softirq completions for queue_mode == 1
blk-mq: merge blk_mq_drain_queue and __blk_mq_drain_queue
blk-mq: properly drain stopped queues
block: remove WQ_POWER_EFFICIENT from kblockd
null_blk: fix name and description of 'queue_mode' module parameter
block: remove elv_abort_queue and blk_abort_flushes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A first set of bug fixes that didn't make it for the merge window, and
two Kconfig cleanups that still make sense at this point.
Unfortunately, one of the two cleanups caused an unintended change in
the original version, so we had to revert one part of it and do some
more testing to ensure the rest is really fine. There was also a
last-minute rebase of the patches to remove another bad commit"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: use menuconfig for sub-arch menus
ARM: multi_v7_defconfig: re-enable SDHCI drivers
ARM: EXYNOS: Fix compilation warning
ARM: exynos: move sysram info to exynos.c
ARM: dts: Specify the NAND ECC scheme explicitly on Armada 385 DB board
ARM: dts: Specify the NAND ECC scheme explicitly on Armada 375 DB board
ARM: exynos: cleanup kconfig option display
misc: vexpress: fix error handling vexpress_syscfg_regmap_init()
ARM: Remove ARCH_HAS_CPUFREQ config option
ARM: integrator: fix section mismatch problem
ARM: mvebu: DT: fix OpenBlocks AX3-4 RAM size
ARM: samsung: make SAMSUNG_DMADEV optional
remoteproc: da8xx: don't select CMA on no-MMU
bus/arm-cci: add dependency on OF && CPU_V7
ARM: keystone requires ARM_PATCH_PHYS_VIRT
ARM: omap2: fix am43xx dependency on l2x0 cache
|
|
W1 reset_bus() should return zero if slave device is present.
This patch fix this issue.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If connector->dpms is left untouched, it defaults
to DRM_MODE_DPMS_ON (0).
As a result, drm_helper_connector_dpms will exit when
it will be asked to set the state to DRM_MODE_DPMS_ON,
because it is already set.
That issue prevented displays from turning on at boot.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tdev->dev has been freed in device_destroy(), it's not right to
use dev_set_drvdata() after that;
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pci_interrupt_cause"
The direct cause is IRQ_SPI is already defined as a macro in unicore32
architecture (also, blackfin and mips architectures define it). The
related error (unicore32 with allmodconfig)
CC [M] drivers/scsi/mvsas/mv_94xx.o
In file included from drivers/scsi/mvsas/mv_94xx.c:27:
drivers/scsi/mvsas/mv_94xx.h:176: error: expected identifier before numeric constant
And IRQ_SAS_A and IRQ_SAS_B are used as 'u32' (although "enum
pci_interrupt_cause" is not used directly, now).
All together, need add 'MVS_' for "enum pci_interrupt_cause".
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Xuetao Guan <gxt@mprc.pku.edu.cn>
Signed-off-by: Xuetao Guan <gxt@mprc.pku.edu.cn>
|
|
It is only a typo issue, the related commit:
"1fbc4c4 drivers/rtc/rtc-puv3.c: use dev_dbg() instead of pr_debug()"
The related error (for unicore32 with allmodconfig):
CC [M] drivers/rtc/rtc-puv3.o
drivers/rtc/rtc-puv3.c: In function 'puv3_rtc_setalarm':
drivers/rtc/rtc-puv3.c:143: error: 'struct device' has no member named 'dev'
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Xuetao Guan <gxt@mprc.pku.edu.cn>
Signed-off-by: Xuetao Guan <gxt@mprc.pku.edu.cn>
|
|
It is only a typo issue, the related commit:
"1fbc4c4 drivers/rtc/rtc-puv3.c: use dev_dbg() instead of pr_debug()"
The related error (unicore32 with allmodconfig):
CC [M] drivers/rtc/rtc-puv3.o
drivers/rtc/rtc-puv3.c: In function 'puv3_rtc_setpie':
drivers/rtc/rtc-puv3.c:74: error: implicit declaration of function 'dev_debug'
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Xuetao Guan <gxt@mprc.pku.edu.cn>
Signed-off-by: Xuetao Guan <gxt@mprc.pku.edu.cn>
|
|
In the conversion to generic early console, the passing of options from
the early 8250 console to the regular ttyS console was broken. This
resulted in the baud rate changing when switching consoles during boot.
This feature allows specifying a single console option on the kernel
command line rather than both an early console and regular serial tty
console. It would be nice to generalize this feature. However, it only
works if the correct baud rate can be probed early which is not the
case on many platforms which have non-standard UART clock rates. So for
now, this is left as an 8250 specific feature.
Reported-and-tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If INPCK is not set, input parity detection should be disabled. This means
parity errors should not be received from the tty driver, and the data
received should be treated normally.
SUS v3, 11.2.2, General Terminal Interface - Input Modes, states:
"If INPCK is set, input parity checking shall be enabled. If INPCK is
not set, input parity checking shall be disabled, allowing output parity
generation without input parity errors. Note that whether input parity
checking is enabled or disabled is independent of whether parity detection
is enabled or disabled (see Control Modes). If parity detection is enabled
but input parity checking is disabled, the hardware to which the terminal
is connected shall recognize the parity bit, but the terminal special file
shall not check whether or not this bit is correctly set."
Ignore parity errors reported by the tty driver when INPCK is not set, and
handle the received data normally.
Fixes: Bugzilla #71681, 'Improvement of n_tty_receive_parity_error from n_tty.c'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio
Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom
Annotated for fixes:
altera_uart
mcf
Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial
Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core
Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from David Vrabel:
"Xen regression and PVH fixes for 3.16-rc1
- fix dom0 PVH memory setup on latest unstable Xen releases
- fix 64-bit x86 PV guest boot failure on Xen 3.1 and earlier
- fix resume regression on non-PV (auto-translated physmap) guests"
* tag 'stable/for-linus-3.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/grant-table: fix suspend for non-PV guests
x86/xen: no need to explicitly register an NMI callback
Revert "xen/pvh: Update E820 to work with PVH (v2)"
x86/xen: fix memory setup for PVH dom0
|
|
* pm-cpufreq:
cpufreq: unlock when failing cpufreq_update_policy()
intel_pstate: Correct rounding in busy calculation
cpufreq: cpufreq-cpu0: fix CPU_THERMAL dependency
* pm-cpuidle:
cpuidle: mvebu: Fix the name of the states
|
|
* acpi-general:
ACPI: use kstrto*() instead of simple_strto*()
* acpi-processor:
ACPI / processor replace __attribute__((packed)) by __packed
* acpi-lpss:
ACPI / LPSS: Take I2C host controllers out of reset
* acpi-battery:
ACPI / battery: add quirk for Acer Aspire V5-573G
ACPI / battery: use callback for setting up quirks
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
First round of fixes for 3.16-rc, mostly cc: stable, and the vt/vgacon
fixes from Daniel [1] to avoid hangs and unclaimed register errors on
module load/reload.
* tag 'drm-intel-fixes-2014-06-17' of git://anongit.freedesktop.org/drm-intel:
drm/i915/bdw: remove erroneous chv specific workarounds from bdw code
drm/i915: fix possible refcount leak when resetting forcewake
drm/i915: Reorder semaphore deadlock check
drm/i95: Initialize active ring->pid to -1
drm/i915: set backlight duty cycle after backlight enable for gen4
drm/i915: Avoid div-by-zero when pixel_multiplier is zero
drm/i915: Disable FBC by default also on Haswell and later
drm/i915: Kick out vga console
drm/i915: Fixup global gtt cleanup
vt: Don't ignore unbind errors in vt_unbind
vt: Fix up unregistration of vt drivers
vt: Fix replacement console check when unbinding
|
|
The acquire ctx will typically be declared on the stack, which means we
could have garbage values for any uninitialized field. In this case, it
was triggering WARN_ON()s because 'contended' had garbage value.
Go ahead and use memset() to be more future-proof.
v2: now with extra brown paper bag
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
With commit aed3f9d498b ("staging: comedi: addi_apci_1564:
absorb apci1564_reset()"), the apci 1564 driver has gained
a dependency on the addi watchdog module, which is not reflected
correctly in Kconfig, and that can lead to link errors
when the watchdog is disabled.
This adds an explicit 'select', like it is done in the other
addi apci drivers that need it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixes a regression in 3.16-rc1 compared to 3.15.
The unbalanced calls would presumably result in the page flip interrupts
never getting disabled once they are enabled.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 75f36d861957cb05b7889af24c8cd4a789398304.
drm_vblank_get() is necessary to ensure the DRM vblank counter value is
up to date in drm_send_vblank_event().
Seems to fix weston hangs waiting for page flips to complete.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Make sure we have an HDMI monitor before validating modes with
clocks >165 Mhz on single link connections.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When we have a passive adapter validate the clocks
against the HMDI/DVI limits.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Need to use the adjusted clock on dce8 as well.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=80029
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The length name of the states 2 was too long to fit in the allocated
string (limited to 16 bytes). This lead to improper string displayed
through sysfs.
This patch shorten the name by removing the reference to Marvell and
to the CPU as both are implicit. For coherency the same change have
been done for the states 1.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit bd0fa9bb455d introduced a failure path to cpufreq_update_policy() if
cpufreq_driver->get(cpu) returns NULL. However, it jumps to the 'no_policy'
label, which exits without unlocking any of the locks the function acquired
earlier. This causes later calls into cpufreq to hang.
Fix this by creating a new 'unlock' label and jumping to that instead.
Fixes: bd0fa9bb455d ("cpufreq: Return error if ->get() failed in cpufreq_update_policy()")
Link: https://devtalk.nvidia.com/default/topic/751903/kernel-3-15-and-nv-drivers-337-340-failed-to-initialize-the-nvidia-kernel-module-gtx-550-ti-/
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 3.16 cycle.
A mixed bag of fixes, many of which feel just to late for 3.15.
* hid sensors - some devices need a feature report request in order to
change power state. This isn't part of the spec, but has been observed
on several devices and does no harm to others.
* mpl3115 has had two errors in the buffer description fixed. The presure is
signed, not unsigned and the temperature has 12 bits rather than 16.
These could lead to incorrect interpretation of the data in userspace.
* tsl2x7x - the high byte of the proximity thresholds should be written along
with the low byte (which was). This could lead to interesting results
with large thresholds.
* twl4030 - a flag to specify processed values were required was not set
when initializing a reading. As such values returned were in an unknown
state. Fixed by simply initializing it appropriately.
* IIO_SIMPLE_DUMMY_BUFFER did not select IIO_BUFFER leading to randconfig
build errors.
* ak8975 was applying an unwanted le16_to_cpu conversion as the i2c framework
already performs one. As such for big endian systems, the bytes would be
in the wrong order in the magnetic field measurements reported.
* mxs-lradc - the controllable voltage dividers were not enabled / disabled for
later channels than the first one during conversion.
* at91_adc error handling returned -ENOMEM in a u8. Return value of
at91_adc_get_trigger_value_by_name changed to int thus allowing -ENOMEM and
also original values to be returned.
* mcb - mcb_request_mem returns and ERR_PTR but the caller was checking for
NULL to detect an error.
|
|
Commit aa8532c32216ae07c3813b9aeb774517878a7573 (xen: refactor suspend
pre/post hooks) broke resuming PVHVM (auto-translated physmap) guests.
The gnttab_suspend() would clear the mapping for the grant table
frames, but the ->unmap_frames() call is only applicable to PV guests.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next
couple more DP regression fixes.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/disp: fix oops in destructor with headless cards
drm/gf117/i2c: no aux channels on this chipset
|
|
If init doesn't run then disp->outp might not be initialized, resulting
in an oops.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Reported-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull device tree fixes from Rob Herring:
- fix microblaze compiling due to conflicting merge window changes
- a fix in of_attach_node due to of_find_node_by_path changes
- prevent format strings in DT kobject names
* tag 'dt-fixes-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
OF: fix of_find_node_by_path() assumption that of_allnodes is root
of: avoid format string parsing in kobject names
of/platform: Fix microblaze build failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull randomness bugfix from Ted Ts'o:
"random: fix entropy accounting bug introduced in v3.15"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: fix nasty entropy accounting bug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few small fixes:
- Fixes for bugs in Palmas and as3722 exposed by recent changes in
the core - the drivers weren't allowing the current configuration
to be read sometimes.
- Provide a stub for regulator_can_change_voltage() for !REGULATOR.
- Make sure ltc3589 only looks at its child nodes in the device tree
rather than searching the whole tree"
* tag 'regulator-v3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: ltc3589: Use of_get_child_by_name
regulator: palmas: Fix SMPS list for 0V
regulator: add regulator_can_change_voltage stub
regulator: as3722: Make 0 a valid selector
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fix from Mark Brown:
"A single bugfix from the merge window, fixing an issue with DMA at
slow speeds on Intel hardware"
* tag 'spi-v3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi/pxa2xx: change default supported DMA burst size to 1
|
|
Fixes the following build error due to a typo introduced
by commit e4ac92df27 ("serial: samsung: Neaten dbg uses"):
drivers/tty/serial/samsung.c:69:26: error: ‘buf’ undeclared (first use in this function)
Reported-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Acked-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In usbtest, tests 5 - 8 use the scatter-gather library in usbcore
without any sort of timeout. If there's a problem in the gadget or
host controller being tested, the test can hang.
This patch adds a 10-second timeout to the tests, so that they will
fail gracefully with an ETIMEDOUT error instead of hanging.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Huang Rui <ray.huang@amd.com>
Tested-by: Huang Rui <ray.huang@amd.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Leandro Liptak reports that his HASEE E200 computer hangs when we ask
the BIOS to hand over control of the EHCI host controller. This
definitely sounds like a bug in the BIOS, but at the moment there is
no way to fix it.
This patch works around the problem by avoiding the handoff whenever
the motherboard and BIOS version match those of Leandro's computer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Leandro Liptak <leandroliptak@gmail.com>
Tested-by: Leandro Liptak <leandroliptak@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 9262c19d14c4 "usb: disable port power control if not supported in
wHubCharacteristics" gated enabling runtime pm for usb_port devices on
whether the parent hub supports power control, which causes a
regression. The port must still be allowed to carry out runtime pm
callbacks and receive a -EAGAIN or -EBUSY result. Otherwise the
usb_port device will transition to the pm error state and trigger the
same for the child usb_device.
Prior to the offending commit usb_hub_create_port_device() arranged for
runtime pm to be disabled is dev_pm_qos_expose_flags() failed. Instead,
force the default state of PM_QOS_FLAG_NO_POWER_OFF flag to be set prior
to enabling runtime pm. If that policy can not be set then fail
registration.
Report: http://marc.info/?l=linux-usb&m=140290586301336&w=2
Fixes: 9262c19d14c4 ("usb: disable port power control if not supported in wHubCharacteristics")
Reported-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the case where platform firmware has specified conflicting values for
port locations it is confusing and otherwise not helpful to throw a
backtrace. Instead, include enough information to determine that
firmware has done something wrong and globally disable port poweroff.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Reading through a recent bug report [1], Alan notes:
"Dan, the warning message in hub_suspend() should mention that the
child device isn't suspended yet."
...update the warning from:
"usb usb3-port4: not suspended yet"
...to:
"usb usb3-port4: device 3-4: not suspended yet"
[1]: http://marc.info/?l=linux-usb&m=140290586301336&w=2
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_stop_device() allocates and issues stop commands for each active endpoint.
This is done with spinlock held and interrupt disabled so we can't sleep during
memory allocation. Use GFP_NOWAIT instead
Regression from commit ddba5cd0aeff5bbed92ebdf4b1223300b0541e78
"xhci: Use command structures when queuing commands on the command ring"
for 3.16-rc1
Fixes: ddba5cd0aeff ("xhci: Use command structures when queuing commands")
Reported-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
