| Age | Commit message (Collapse) | Author |
|---|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The i2c controller used by Freescales iMX processors is the same
hardware module used on Freescales ColdFire family of processors.
We can use the existing i2c-imx driver on ColdFire family members.
Modify the configuration to allow it to be selected when compiling
for ColdFire targets.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Instantiated I2C device nodes are marked with OF_POPULATE. This was
introduced in 4f001fd30145a6. On unloading, loaded device nodes will of
course be unmarked. The problem are nodes that fail during
initialisation: If a node fails, it won't be unloaded and hence not be
unmarked.
If a I2C driver module is unloaded and reloaded, it will skip nodes that
failed before.
Skip device nodes that are already populated and mark them only in case
of success.
Fixes: 4f001fd30145a6 ("i2c: Mark instantiated device nodes with OF_POPULATE")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[wsa: use 14-digit commit sha]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
We found a bug that i2c transfer sometimes failed on 3066a board with
stabel-4.8, the con register would be updated by uninitialized tuning
value, it made the i2c transfer failed.
So give the tuning value to be zero during rk3x_i2c_v0_calc_timings.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
This driver should be buildable with ARCH_HISI,
because some of other HiSilicon SoCs also use it.
Signed-off-by: Ruqiang Ju <juruqiang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
After commit b09b5224fe86 ("usb: chipidea: implement platform shutdown
callback") and commit 43a404577a93 ("usb: chipidea: host: set host to
be null after hcd is freed") a NULL pointer dereference is caused
on i.MX23 during shutdown. So ensure that role is set to CI_ROLE_END and
we finish interrupt handling before the hcd is deallocated. This avoids
the NULL pointer dereference.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: b09b5224fe86 ("usb: chipidea: implement platform shutdown callback")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The host keeps sending heartbeat packets independent of the
guest responding to them. Even though we respond to the heartbeat messages at
interrupt level, we can have situations where there maybe multiple heartbeat
messages pending that have not been responded to. For instance this occurs when the
VM is paused and the host continues to send the heartbeat messages.
Address this issue by draining and responding to all
the heartbeat messages that maybe pending.
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a regression caused by the stack vmalloc change"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: core - Don't use a stack buffer in add_early_randomness()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"This is the first batch of clk driver fixes for this release.
We have a handful of fixes for the uniphier clk driver that was
introduced recently, as well as Kconfig option hiding, module
autoloading markings, and a few fixes for clk_hw based registration
patches that went in this merge window"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: at91: Fix a return value in case of error
clk: uniphier: rename MIO clock to SD clock for Pro5, PXs2, LD20 SoCs
clk: uniphier: fix memory overrun bug
clk: hi6220: use CLK_OF_DECLARE_DRIVER for sysctrl and mediactrl clock init
clk: mvebu: armada-37xx-periph: Fix the clock gate flag
clk: bcm2835: Clamp the PLL's requested rate to the hardware limits.
clk: max77686: fix number of clocks setup for clk_hw based registration
clk: mvebu: armada-37xx-periph: Fix the clock provider registration
clk: core: add __init decoration for CLK_OF_DECLARE_DRIVER function
clk: mediatek: Add hardware dependency
clk: samsung: clk-exynos-audss: Fix module autoload
clk: uniphier: fix type of variable passed to regmap_read()
clk: uniphier: add system clock support for sLD3 SoC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a set of GPIO fixes for the v4.9 kernel series:
- Fix up off-by one and line offset validation, info leak to
userspace, and reject invalid flags. Those are especially valuable
hardening patches from Lars-Peter Clausen, all tagged for stable.
- Fix module autoload for TS4800 and ATH79.
- Correct the IRQ handler for MPC8xxx to use handle_level_irq() as it
(a) reacts to edges not levels and (b) even implements .irq_ack().
We were missing IRQs here.
- Fix the error path for acpi_dev_gpio_irq_get()
- Fix a memory leak in the MXS driver.
- Fix an annoying typo in the STMPE driver.
- Put a dependency on sysfs to the mockup driver"
* tag 'gpio-v4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mpc8xxx: Correct irq handler function
gpio: ath79: Fix module autoload
gpio: ts4800: Fix module autoload
gpio: GPIO_GET_LINEEVENT_IOCTL: Reject invalid line and event flags
gpio: GPIO_GET_LINEHANDLE_IOCTL: Reject invalid line flags
gpio: GPIOHANDLE_GET_LINE_VALUES_IOCTL: Fix information leak
gpio: GPIO_GET_LINEEVENT_IOCTL: Validate line offset
gpio: GPIOHANDLE_GET_LINE_VALUES_IOCTL: Fix information leak
gpio: GPIO_GET_LINEHANDLE_IOCTL: Validate line offset
gpio: GPIO_GET_CHIPINFO_IOCTL: Fix information leak
gpio: GPIO_GET_CHIPINFO_IOCTL: Fix line offset validation
gpio / ACPI: fix returned error from acpi_dev_gpio_irq_get()
gpio: mockup: add sysfs dependency
gpio: stmpe: || vs && typo
gpio: mxs: Unmap region obtained by of_iomap
gpio/board.txt: point to gpiod_set_value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from David Vrabel:
- advertise control feature flags in xenstore
- fix x86 build when XEN_PVHVM is disabled
* tag 'for-linus-4.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xenbus: check return value of xenbus_scanf()
xenbus: prefer list_for_each()
x86: xen: move cpu_up functions out of ifdef
xenbus: advertise control feature flags
|
|
The only times at which intel_pstate checks the policy set for
a given CPU is the initialization of that CPU and updates of its
policy settings from cpufreq when intel_pstate_set_policy() is
invoked.
That is insufficient, however, because intel_pstate uses the same
P-state selection function for all CPUs regardless of the policy
setting for each of them and the P-state limits are shared between
them. Thus if the policy is set to "performance" for a particular
CPU, it may not behave as expected if the cpufreq settings are
changed subsequently for another CPU.
That can be easily demonstrated by writing "performance" to
scaling_governor for all CPUs and then switching it to "powersave"
for one of them in which case all of the CPUs will behave as though
their scaling_governor were all "powersave" (even though the policy
still appears to be "performance" for the remaining CPUs).
Fix this problem by modifying intel_pstate_adjust_busy_pstate() to
always set the P-state to the maximum allowed by the current limits
for all CPUs whose policy is set to "performance".
Note that it still is recommended to always change the policy setting
in the same way for all CPUs even with this fix applied to avoid
confusion.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 0eadf37afc250 ("nbd: allow block mq to deal with timeouts")
changed normal usage of nbd->sock_lock to use spin_lock/spin_unlock
rather than the *_irq variants, but it missed this unlock in an
error path.
Found by Coverity, CID 1373871.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Fixes: 0eadf37afc250 ("nbd: allow block mq to deal with timeouts")
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
SEC registers are not accessible when the TXE device is in low power
state, hence the SEC interrupt cannot be processed if device is not
awake.
In some rare cases entrance to low power state (aliveness off) and input
ready bits can be signaled at the same time, resulting in communication
stall as input ready won't be signaled again after waking up. To resolve
this IPC_HHIER_SEC bit in HHISR_REG should not be cleaned if the
interrupt is not processed.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
struct
Prevents leaking pointers between processes
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Martijn Coenen <maco@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Prevent using a binder_ref with only weak references where a strong
reference is required.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Martijn Coenen <maco@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dm_get_target_type() was previously called so any error returned from
dm_table_add_target() must first call dm_put_target_type(). Otherwise
the DM target module's reference count will leak and the associated
kernel module will be unable to be removed.
Also, leverage the fact that r is already -EINVAL and remove an extra
newline.
Fixes: 36a0456 ("dm table: add immutable feature")
Fixes: cc6cbe1 ("dm table: add always writeable feature")
Fixes: 3791e2f ("dm table: add singleton feature")
Cc: stable@vger.kernel.org # 3.2+
Signed-off-by: tang.junhui <tang.junhui@zte.com.cn>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Don't ignore errors here: Set backend state to unknown when
unsuccessful.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
This is more efficient than list_for_each_safe() when list modification
is accompanied by breaking out of the loop.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
The Xen docs specify several flags which a guest can set to advertise
which values of the xenstore control/shutdown key it will recognize.
This patch adds code to write all the relevant feature-flag keys.
Based-on-patch-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
We should release ->interfaces[0] as well.
Fixes: b15d97d77017 ("greybus: core: add module abstraction")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix to return a negative error code from the es2_arpc_in_enable() error
handling case instead of 0, as done elsewhere in this function.
Fixes: 9d9d3777a9db ("greybus: es2: Add a new bulk in endpoint for APBridgeA RPC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
arche_platform_change_state()
This node pointer is returned by of_find_compatible_node() with
refcount incremented in this function. of_node_put() on it before
exitting this function.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the copy_to_user() fails we should unlock and return directly without
updating "cnt". Also the return value should be -EFAULT instead of the
number of bytes remaining.
Fixes: 02b23803c6af ("staging: android: ion: Add ioctl to query available heaps")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since the controller on R-Car Gen3 doesn't have any status registers
to detect initialization (LPSTS.SUSPM = 1) and the initialization needs
up to 45 usec, this patch adds wait after the initialization. Otherwise,
writing other registers (e.g. INTENB0) will fail.
Fixes: de18757e272d ("usb: renesas_usbhs: add R-Car Gen3 power control")
Cc: <stable@vger.kernel.org> # v4.6+
Cc: <balbi@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Although ghes_proc() tests for errors while reading the error status,
it always return success (0). Fix this by propagating the return
value.
Fixes: d334a49113a4a33 (ACPI, APEI, Generic Hardware Error Source memory error support)
Signed-of-by: Punit Agrawal <punit.agrawa.@arm.com>
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Increase ohci watchout delay to 275 ms. Previous delay was 250 ms
with 20 ms of slack, after removing slack time some ohci controllers don't
respond in time. Logs from systems with controllers that have the
issue would show "HcDoneHead not written back; disabled"
Signed-off-by: Bryan Paluch <bryanpaluch@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we're booting pandaboard using NFSroot over built-in g_ether, we
can get the following after booting once and doing a warm reset:
g_ether gadget: ecm_open
g_ether gadget: notify connect true
...
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x220/0x34c
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Read):
Data Access in User mode du ring Functional access
...
Fix the issue by calling pm_runtime functions from
musb_gadget_queue.
Note that in the long run we should be able to queue the pending
transfers if pm_runtime is not active, and flush the queue from
pm_runtime_resume.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we configure musb with 2430 glue as a peripheral, and then rmmod
omap2430 module, we'll get the following error:
[ INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected ]
...
rmmod/413 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
(&phy->mutex){+.+.+.}, at: [<c04b9fd0>] phy_power_off+0x1c/0xb8
[ 204.678710]
and this task is already holding:
(&(&musb->lock)->rlock){-.-...}, at: [<bf3a482c>]
musb_gadget_stop+0x24/0xec [musb_hdrc]
which would create a new lock dependency:
(&(&musb->lock)->rlock){-.-...} -> (&phy->mutex){+.+.+.}
...
This is because some glue layers expect musb_platform_enable/disable
to be called with spinlock held, and 2430 glue layer has USB PHY on
the I2C bus using a mutex.
We could fix the glue layers to take the spinlock, but we still have
a problem of musb_plaform_enable/disable being called in an unbalanced
manner. So that would still lead into USB PHY enable/disable related
problems for omap2430 glue layer.
While it makes sense to only enable USB PHY when needed from PM point
of view, in this case we just can't do it yet without breaking things.
So let's just revert phy_enable/disable related changes instead and
reconsider this after we have fixed musb_platform_enable/disable to
be balanced.
Fixes: a83e17d0f73b ("usb: musb: Improve PM runtime and phy handling for 2430 glue layer")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Socionext LD11 SoC (arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi)
needs to handle 4 reset lines for EHCI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The reset value of RWC is 0, set RemoteWakeupConnected bit explicitly
before calling ohci_run, it also fixes the issue that the mass
storage stick connected wasn't suspended when the system suspend.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 103544d86976 ("ACPI,PCI,IRQ: reduce resource requirements")
replaced the addition of PIRQ_PENALTY_PCI_USING in acpi_pci_link_allocate()
with an addition in acpi_irq_pci_sharing_penalty(), but f7eca374f000
("ACPI,PCI,IRQ: separate ISA penalty calculation") removed the use
of acpi_irq_pci_sharing_penalty() for ISA IRQs.
Therefore, PIRQ_PENALTY_PCI_USING is missing from ISA IRQs used by
interrupt links. Include that penalty by adding it in the
acpi_pci_link_allocate() path.
Fixes: f7eca374f000 (ACPI,PCI,IRQ: separate ISA penalty calculation)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Ondrej reported that IRQs stopped working in v4.7 on several
platforms. A typical scenario, from Ondrej's VT82C694X/694X, is:
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: No IRQ available for PCI Interrupt Link [LNKA]
8139too 0000:00:0f.0: PCI INT A: no GSI
We're using PIC routing, so acpi_irq_balance == 0, and LNKA is already
active at IRQ 11. In that case, acpi_pci_link_allocate() only tries
to use the active IRQ (IRQ 11) which also happens to be the SCI.
We should penalize the SCI by PIRQ_PENALTY_PCI_USING, but
irq_get_trigger_type(11) returns something other than
IRQ_TYPE_LEVEL_LOW, so we penalize it by PIRQ_PENALTY_ISA_ALWAYS
instead, which makes acpi_pci_link_allocate() assume the IRQ isn't
available and give up.
Add acpi_penalize_sci_irq() so platforms can tell us the SCI IRQ,
trigger, and polarity directly and we don't have to depend on
irq_get_trigger_type().
Fixes: 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
Link: http://lkml.kernel.org/r/201609251512.05657.linux@rainbow-software.org
Reported-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We do not want to store the SCI penalty in the acpi_isa_irq_penalty[]
table because acpi_isa_irq_penalty[] only holds ISA IRQ penalties and
there's no guarantee that the SCI is an ISA IRQ. We add in the SCI
penalty as a special case in acpi_irq_get_penalty().
But if we called acpi_penalize_isa_irq() or acpi_irq_penalty_update()
for an SCI that happened to be an ISA IRQ, they stored the SCI
penalty (part of the acpi_irq_get_penalty() return value) in
acpi_isa_irq_penalty[]. Subsequent calls to acpi_irq_get_penalty()
returned a penalty that included *two* SCI penalties.
Fixes: 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.9 cycle.
* atlas chemical
- Fix alignment of big endian values in a larger storage (by using the right
size storage)
* maxim thermocouple
- Fix alignment of big endian values in larger (by using the correct
sized storage).
* sca3000
- Handle unexpected mode values.
* ti-adc081
- Select IIO_TRIGGERED_BUFFER to avoid build errors
|
|
In some error paths in functions cxl_start_context and
afu_ioctl_start_work pid references to the current & group-leader tasks
can leak after they are taken. This patch fixes these error paths to
release these pid references before exiting the error path.
Fixes: 7b8ad495d592 ("cxl: Fix DSI misses when the context owning task exits")
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
From the beginning of the gpio-mpc8xxx.c, the "handle_level_irq"
has being used to handle GPIO interrupts in the PowerPC/Layerscape
platforms. But actually, almost all PowerPC/Layerscape platforms
assert an interrupt request upon either a high-to-low change or
any change on the state of the signal.
So the "handle_level_irq" is not reasonable for PowerPC/Layerscape
GPIO interrupt, it should be "handle_edge_irq". Otherwise the system
may lost some interrupts from the PIN's state changes.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull UBI[FS] fixes from Richard Weinberger:
"This contains fixes for issues in both UBI and UBIFS:
- Fallout from the merge window, refactoring UBI code introduced some
issues.
- Fixes for an UBIFS readdir bug which can cause getdents() to busy
loop for ever and a bug in the UBIFS xattr code"
* tag 'upstream-4.9-rc2' of git://git.infradead.org/linux-ubifs:
ubifs: Abort readdir upon error
UBI: Fix crash in try_recover_peb()
ubi: fix swapped arguments to call to ubi_alloc_aeb
ubifs: Fix xattr_names length in exit paths
ubifs: Rename ubifs_rename2
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target-pending fixes for v4.9-rc2.
This includes:
- Fix v4.1.y+ reference leak regression with concurrent TMR
ABORT_TASK + session shutdown. (Vaibhav Tandon)
- Enable tcm_fc w/ SCF_USE_CPUID to avoid host exchange timeouts
(Hannes)
- target/user error sense handling fixes. (Andy + MNC + HCH)
- Fix iscsi-target NOP_OUT error path iscsi_cmd descriptor leak
(Varun)
- Two EXTENDED_COPY SCSI status fixes for ESX VAAI (Dinesh Israni +
Nixon Vincent)
- Revert a v4.8 residual overflow change, that breaks sg_inq with
small allocation lengths.
There are a number of folks stress testing the v4.1.y regression fix
in their environments, and more folks doing iser-target I/O stress
testing atop recent v4.x.y code.
There is also one v4.2.y+ RCU conversion regression related to
explicit NodeACL configfs changes, that is still being tracked down"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/tcm_fc: use CPU affinity for responses
target/tcm_fc: Update debugging statements to match libfc usage
target/tcm_fc: return detailed error in ft_sess_create()
target/tcm_fc: print command pointer in debug message
target: fix potential race window in target_sess_cmd_list_waiting()
Revert "target: Fix residual overflow handling in target_complete_cmd_with_length"
target: Don't override EXTENDED_COPY xcopy_pt_cmd SCSI status code
target: Make EXTENDED_COPY 0xe4 failure return COPY TARGET DEVICE NOT REACHABLE
target: Re-add missing SCF_ACK_KREF assignment in v4.1.y
iscsi-target: fix iscsi cmd leak
iscsi-target: fix spelling mistake "Unsolicitied" -> "Unsolicited"
target/user: Fix comments to not refer to data ring
target/user: Return an error if cmd data size is too large
target/user: Use sense_reason_t in tcmu_queue_cmd_ring
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Couple of hwmon fixes:
Fix a potential ERR_PTR dereference in max31790 driver, and handle
temperature readings below 0 in adm9240 driver"
* tag 'hwmon-for-linus-v4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (max31790) potential ERR_PTR dereference
hwmon: (adm9240) handle temperature readings below 0
|
|
Pull IPMI updates from Corey Minyard:
"A small bug fix and a new driver for acting as an IPMI device.
I was on vacation during the merge window (a long vacation) but this
is a bug fix that should go in and a new driver that shouldn't hurt
anything.
This has been in linux-next for a month or so"
* tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: fix crash on reading version from proc after unregisted bmc
ipmi/bt-bmc: remove redundant return value check of platform_get_resource()
ipmi/bt-bmc: add a dependency on ARCH_ASPEED
ipmi: Fix ioremap error handling in bt-bmc
ipmi: add an Aspeed BT IPMI BMC driver
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/gpio/gpio-ath79.ko | grep alias
$
After this patch:
$ modinfo drivers/gpio/gpio-ath79.ko | grep alias
alias: of:N*T*Cqca,ar9340-gpioC*
alias: of:N*T*Cqca,ar9340-gpio
alias: of:N*T*Cqca,ar7100-gpioC*
alias: of:N*T*Cqca,ar7100-gpio
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Aban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The newly added __sca3000_get_base_freq function handles all valid
modes of the SCA3000_REG_ADDR_MODE register, but gcc notices
that any other value (i.e. 0x00) causes the base_freq variable to
not get initialized:
drivers/staging/iio/accel/sca3000_core.c: In function 'sca3000_write_raw':
drivers/staging/iio/accel/sca3000_core.c:527:23: error: 'base_freq' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This adds explicit error handling for unexpected register values,
to ensure this cannot happen.
Fixes: e0f3fc9b47e6 ("iio: accel: sca3000_core: implemented IIO_CHAN_INFO_SAMP_FREQ")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ico Doornekamp <ico@pruts.nl>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
endian value
This will result in a random value being reported on big endian architectures.
(thanks to Lars-Peter Clausen for pointing out the effects of this bug)
Only effects a value printed to the log, but as this reports the settings of
the probe in question it may be of direct interest to users.
Also, fixes the following sparse endianness warnings:
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Fixes: e8dd92bfbff25 ("iio: chemical: atlas-ph-sensor: add EC feature")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"This updates contains:
- A revert which addresses a boot failure on ARM Sun5i platforms
- A new clocksource driver, which has been delayed beyond rc1 due to
an interrupt driver issue which was unearthed by this driver. The
debugging of that issue and the discussion about the proper
solution made this driver miss the merge window. There is no point
in delaying it for a full cycle as it completes the basic mainline
support for the new JCore platform and does not create any risk
outside of that platform"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "clocksource/drivers/timer_sun5i: Replace code by clocksource_mmio_init"
clocksource: Add J-Core timer/clocksource driver
of: Add J-Core timer bindings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"Mostly irqchip driver fixes, plus a symbol export"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kernel/irq: Export irq_set_parent()
irqchip/gic: Add missing \n to CPU IF adjustment message
irqchip/jcore: Don't show Kconfig menu item for driver
irqchip/eznps: Drop pointless static qualifier in nps400_of_init()
irqchip/gic-v3-its: Fix entry size mask for GITS_BASER
irqchip/gic-v3-its: Fix 64bit GIC{R,ITS}_TYPER accesses
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Add Ard Biesheuvel as EFI co-maintainer, plus fix an ARM build bug
with older toolchains"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm: Fix absolute relocation detection for older toolchains
MAINTAINERS: Add myself as EFI maintainer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.9-rc2
Here's a fix for a NULL-deref during probe which could be triggered by a
malicious device, and a fix for some missing error handling in cp210x
that also leaked some bits from the stack. Included is also a new device
id for ftdi_sio.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
