| Age | Commit message (Collapse) | Author |
|---|
|
Currently the NUMA distance map parsing does not validate the distance
table for the distance-matrix rules 1-2 in [1].
However the arch NUMA code may enforce some of these rules, but not all.
Such is the case for the arm64 port, which does not enforce the rule that
the distance between separates nodes cannot equal LOCAL_DISTANCE.
The patch adds the following rules validation:
- distance of node to self equals LOCAL_DISTANCE
- distance of separate nodes > LOCAL_DISTANCE
This change avoids a yet-unresolved crash reported in [2].
A note on dealing with symmetrical distances between nodes:
Validating symmetrical distances between nodes is difficult. If it were
mandated in the bindings that every distance must be recorded in the
table, then it would be easy. However, it isn't.
In addition to this, it is also possible to record [b, a] distance only
(and not [a, b]). So, when processing the table for [b, a], we cannot
assert that current distance of [a, b] != [b, a] as invalid, as [a, b]
distance may not be present in the table and current distance would be
default at REMOTE_DISTANCE.
As such, we maintain the policy that we overwrite distance [a, b] = [b, a]
for b > a. This policy is different to kernel ACPI SLIT validation, which
allows non-symmetrical distances (ACPI spec SLIT rules allow it). However,
the distance debug message is dropped as it may be misleading (for a distance
which is later overwritten).
Some final notes on semantics:
- It is implied that it is the responsibility of the arch NUMA code to
reset the NUMA distance map for an error in distance map parsing.
- It is the responsibility of the FW NUMA topology parsing (whether OF or
ACPI) to enforce NUMA distance rules, and not arch NUMA code.
[1] Documents/devicetree/bindings/numa.txt
[2] https://www.spinics.net/lists/arm-kernel/msg683304.html
Cc: stable@vger.kernel.org # 4.7
Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
of_dma_configure() was *supposed* to be following the same logic as
acpi_dma_configure() and only setting bus_dma_mask if some range was
specified by the firmware. However, it seems that subtlety got lost in
the process of fitting it into the differently-shaped control flow, and
as a result the force_dma==true case ends up always setting the bus mask
to the 32-bit default, which is not what anyone wants.
Make sure we only touch it if the DT actually said so.
Fixes: 6c2fb2ea7636 ("of/device: Set bus DMA mask as appropriate")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Robert Richter <robert.richter@cavium.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Similar to gxbb and gxl platforms, axg SCPI Cortex-M co-processor
uses the fdiv2 and fdiv3 to, among other things, provide the cpu
clock.
Until clock hand-off mechanism makes its way to CCF and the generic
SCPI claims platform specific clocks, these clocks must be marked as
critical to make sure they are never disabled when needed by the
co-processor.
Fixes: 05f814402d61 ("clk: meson: add fdiv clock gates")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
On the Khadas VIM2 (GXM) and LePotato (GXL) board there are problems
with reboot; e.g. a ~60 second delay between issuing reboot and the
board power cycling (and in some OS configurations reboot will fail
and require manual power cycling).
Similar to 'commit c987ac6f1f088663b6dad39281071aeb31d450a8 ("clk:
meson-gxbb: set fclk_div2 as CLK_IS_CRITICAL")' the SCPI Cortex-M4
Co-Processor seems to depend on FCLK_DIV3 being operational.
Until commit 05f814402d6174369b3b29832cbb5eb5ed287059 ("clk:
meson: add fdiv clock gates"), this clock was modeled and left on by
the bootloader.
We don't have precise documentation about the SCPI Co-Processor and
its clock requirement so we are learning things the hard way.
Marking this clock as critical solves the problem but it should not
be viewed as final solution. Ideally, the SCPI driver should claim
these clocks. We also depends on some clock hand-off mechanism
making its way to CCF, to make sure the clock stays on between its
registration and the SCPI driver probe.
Fixes: 05f814402d61 ("clk: meson: add fdiv clock gates")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull MTD fixes from Boris Brezillon:
"MTD changes:
- Kill a VLA in sa1100
SPI NOR changes:
- Make sure ->addr_width is restored when SFDP parsing fails
- Propate errors happening in cqspi_direct_read_execute()
NAND changes:
- Fix kernel-doc mismatch
- Fix nanddev_neraseblocks() to return the correct value
- Avoid selection of BCH_CONST_PARAMS when some users require dynamic
BCH settings"
* tag 'mtd/fixes-for-4.20-rc2' of git://git.infradead.org/linux-mtd:
mtd: nand: Fix nanddev_pos_next_page() kernel-doc header
mtd: sa1100: avoid VLA in sa1100_setup_mtd
mtd: spi-nor: Reset nor->addr_width when SFDP parsing failed
mtd: spi-nor: cadence-quadspi: Return error code in cqspi_direct_read_execute()
mtd: nand: Fix nanddev_neraseblocks()
mtd: nand: drop kernel-doc notation for a deleted function parameter
mtd: docg3: don't set conflicting BCH_CONST_PARAMS option
|
|
On architectures with CBAUDEX == 0 (Alpha and PowerPC), the code in tty_baudrate.c does
not do any limit checking on the tty_baudrate[] array, and in fact a
buffer overrun is possible on both architectures. Add a limit check to
prevent that situation.
This will be followed by a much bigger cleanup/simplification patch.
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Requested-by: Cc: Johan Hovold <johan@kernel.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Eugene Syromiatnikov <esyr@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If you run aptitude on framebuffer console, the display is corrupted. The
corruption is caused by the commit d8ae7242. The patch adds "offset" to
"start" when calling scr_memsetw, but it forgets to do the same addition
on a subsequent call to do_update_region.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: d8ae72427187 ("vt: preserve unicode values corresponding to screen characters")
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
VLAN.TCI == 0 is perfectly valid (802.1p), so allow it to be accelerated.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't request tag insertion when it isn't present in outgoing skb.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver version string is obviously not meant to be changed at run
time, so mark it `const'.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the temporary data buffer used when tapping into the SMT Tx queue
from the outer function level into the conditional block it's actually
used in and its containing skb is also declared, making the structure of
code better.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix:
drivers/net/fddi/defza.h:238:1: warning: "/*" within comment [-Wcomment]
by adding a missing comment closing.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SPDX annotation for this driver does not match the license text,
which specifies GNU GPL 2 or later. Make the two match by correcting
the SPDX tag.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[why]
Removing connector reusage from DM to match the rest of the tree ended
up revealing an issue that was surprisingly subtle. The original amdgpu
code for DC that was submitted appears to have left a chunk in
dm_dp_create_fake_mst_encoder() that tries to find a "master encoder",
the likes of which isn't actually used or stored anywhere. It does so at
the wrong time as well by trying to access parts of the drm_connector
from the encoder init before it's actually been initialized. This
results in a NULL pointer deref on MST hotplugs:
[ 160.696613] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[ 160.697234] PGD 0 P4D 0
[ 160.697814] Oops: 0010 [#1] SMP PTI
[ 160.698430] CPU: 2 PID: 64 Comm: kworker/2:1 Kdump: loaded Tainted: G O 4.19.0Lyude-Test+ #2
[ 160.699020] Hardware name: HP HP ZBook 15 G4/8275, BIOS P70 Ver. 01.22 05/17/2018
[ 160.699672] Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
[ 160.700322] RIP: 0010: (null)
[ 160.700920] Code: Bad RIP value.
[ 160.701541] RSP: 0018:ffffc9000029fc78 EFLAGS: 00010206
[ 160.702183] RAX: 0000000000000000 RBX: ffff8804440ed468 RCX: ffff8804440e9158
[ 160.702778] RDX: 0000000000000000 RSI: ffff8804556c5700 RDI: ffff8804440ed000
[ 160.703408] RBP: ffff880458e21800 R08: 0000000000000002 R09: 000000005fca0a25
[ 160.704002] R10: ffff88045a077a3d R11: ffff88045a077a3c R12: ffff8804440ed000
[ 160.704614] R13: ffff880458e21800 R14: ffff8804440e9000 R15: ffff8804440e9000
[ 160.705260] FS: 0000000000000000(0000) GS:ffff88045f280000(0000) knlGS:0000000000000000
[ 160.705854] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 160.706478] CR2: ffffffffffffffd6 CR3: 000000000200a001 CR4: 00000000003606e0
[ 160.707124] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 160.707724] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 160.708372] Call Trace:
[ 160.708998] ? dm_dp_add_mst_connector+0xed/0x1d0 [amdgpu]
[ 160.709625] ? drm_dp_add_port+0x2fa/0x470 [drm_kms_helper]
[ 160.710284] ? wake_up_q+0x54/0x70
[ 160.710877] ? __mutex_unlock_slowpath.isra.18+0xb3/0x110
[ 160.711512] ? drm_dp_dpcd_access+0xe7/0x110 [drm_kms_helper]
[ 160.712161] ? drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper]
[ 160.712762] ? drm_dp_check_and_send_link_address+0xa3/0xd0 [drm_kms_helper]
[ 160.713408] ? drm_dp_mst_link_probe_work+0x4b/0x80 [drm_kms_helper]
[ 160.714013] ? process_one_work+0x1a1/0x3a0
[ 160.714667] ? worker_thread+0x30/0x380
[ 160.715326] ? wq_update_unbound_numa+0x10/0x10
[ 160.715939] ? kthread+0x112/0x130
[ 160.716591] ? kthread_create_worker_on_cpu+0x70/0x70
[ 160.717262] ? ret_from_fork+0x35/0x40
[ 160.717886] Modules linked in: amdgpu(O) vfat fat snd_hda_codec_generic joydev i915 chash gpu_sched ttm i2c_algo_bit drm_kms_helper snd_hda_codec_hdmi hp_wmi syscopyarea iTCO_wdt sysfillrect sparse_keymap sysimgblt fb_sys_fops snd_hda_intel usbhid wmi_bmof drm snd_hda_codec btusb snd_hda_core intel_rapl btrtl x86_pkg_temp_thermal btbcm btintel coretemp snd_pcm crc32_pclmul bluetooth psmouse snd_timer snd pcspkr i2c_i801 mei_me i2c_core soundcore mei tpm_tis wmi tpm_tis_core hp_accel ecdh_generic lis3lv02d tpm video rfkill acpi_pad input_polldev hp_wireless pcc_cpufreq crc32c_intel serio_raw tg3 xhci_pci xhci_hcd [last unloaded: amdgpu]
[ 160.720141] CR2: 0000000000000000
Somehow the connector reusage DM was using for MST connectors managed to
paper over this issue entirely; hence why this was never caught until
now.
[how]
Since this code isn't used anywhere and seems useless anyway, we can
just drop it entirely. This appears to fix the issue on my HP ZBook with
an AMD WX4150.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
It is not safe to keep existing connector while entire topology
has been removed. Could lead potential impact to uapi.
Entirely unregister all the connectors on the topology,
and use a new set of connectors when the topology is plugged back
on.
[How]
Remove the drm connector entirely each time when the
corresponding MST topology is gone.
When hotunplug a connector (e.g., DP2)
1. Remove connector from userspace.
2. Drop it's reference.
When hotplug back on:
1. Detect new topology, and create new connectors.
2. Notify userspace with sysfs hotplug event.
3. Reprobe new connectors, and reassign CRTC from old (e.g., DP2)
to new (e.g., DP3) connector.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
It is not correct to touch aconnector within atomic_check.
[How]
It was added as workaround before, and no longer needed.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
With UCLK DPM enabled, slow switching is not supported any more.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Otherwise big gap between these two clocks may causes
some hangs.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We will meet below issue due to mutex_lock() is called in interrupt context.
The mutex lock is used to protect the pattern trigger data, but before changing
new pattern trigger data (pattern values or repeat value) by users, we always
cancel the timer firstly to clear previous patterns' performance. That means
there is no race in pattern_trig_timer_function(), so we can drop the mutex
lock in pattern_trig_timer_function() to avoid this issue.
Moreover we can move the timer cancelling into mutex protection, since there
is no deadlock risk if we remove the mutex lock in pattern_trig_timer_function().
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/1
CPU: 1 PID: 0 Comm: swapper/1 Not tainted
4.20.0-rc1-koelsch-00841-ga338c8181013c1a9 #171
Hardware name: Generic R-Car Gen2 (Flattened Device Tree)
[<c020f19c>] (unwind_backtrace) from [<c020aecc>] (show_stack+0x10/0x14)
[<c020aecc>] (show_stack) from [<c07affb8>] (dump_stack+0x7c/0x9c)
[<c07affb8>] (dump_stack) from [<c02417d4>] (___might_sleep+0xf4/0x158)
[<c02417d4>] (___might_sleep) from [<c07c92c4>] (mutex_lock+0x18/0x60)
[<c07c92c4>] (mutex_lock) from [<c067b28c>] (pattern_trig_timer_function+0x1c/0x11c)
[<c067b28c>] (pattern_trig_timer_function) from [<c027f6fc>] (call_timer_fn+0x1c/0x90)
[<c027f6fc>] (call_timer_fn) from [<c027f944>] (expire_timers+0x94/0xa4)
[<c027f944>] (expire_timers) from [<c027fc98>] (run_timer_softirq+0x108/0x15c)
[<c027fc98>] (run_timer_softirq) from [<c02021cc>] (__do_softirq+0x1d4/0x258)
[<c02021cc>] (__do_softirq) from [<c0224d24>] (irq_exit+0x64/0xc4)
[<c0224d24>] (irq_exit) from [<c0268dd0>] (__handle_domain_irq+0x80/0xb4)
[<c0268dd0>] (__handle_domain_irq) from [<c045e1b0>] (gic_handle_irq+0x58/0x90)
[<c045e1b0>] (gic_handle_irq) from [<c02019f8>] (__irq_svc+0x58/0x74)
Exception stack(0xeb483f60 to 0xeb483fa8)
3f60: 00000000 00000000 eb9afaa0 c0217e80 00000000 ffffe000 00000000 c0e06408
3f80: 00000002 c0e0647c c0c6a5f0 00000000 c0e04900 eb483fb0 c0207ea8 c0207e98
3fa0: 60020013 ffffffff
[<c02019f8>] (__irq_svc) from [<c0207e98>] (arch_cpu_idle+0x1c/0x38)
[<c0207e98>] (arch_cpu_idle) from [<c0247ca8>] (do_idle+0x138/0x268)
[<c0247ca8>] (do_idle) from [<c0248050>] (cpu_startup_entry+0x18/0x1c)
[<c0248050>] (cpu_startup_entry) from [<402022ec>] (0x402022ec)
Fixes: 5fd752b6b3a2 ("leds: core: Introduce LED pattern trigger")
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Remove bogus __init annotations in ibmpowernv driver
- Fix double-free in error handling of __hwmon_device_register()
* tag 'hwmon-for-v4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ibmpowernv) Remove bogus __init annotations
hwmon: (core) Fix double-free in __hwmon_device_register()
|
|
The assignment of the feature flag NETIF_F_NTUPLE and NETIF_F_HW_TC
occurs prior to the initial setup of the local hw_features variable.
This means the features are set as user-changeable, but are not set in
the currently active feature list. This results in the features being
disabled at the driver's initial load.
Move the assignment after the initial assignment of hw_features, and
assign to the local variable. This ensures that NETIF_F_NTUPLE and
NETIF_F_HW_TC are marked as user-changeable, and also enables them by
default when the driver loads.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since commit bacd75cfac8a ("i40e/i40evf: Add capability exchange for
outer checksum", 2017-04-06) the i40e driver has not reported support
for IP-in-IP offloads. This likely occurred due to a bad rebase, as the
commit extracts hw_enc_features into its own variable. As part of this
change, it dropped the NETIF_F_FSO_IPXIP flags from the
netdev->hw_enc_features. This was unfortunately not caught during code
review.
Fix this by adding back the missing feature flags.
For reference, NETIF_F_GSO_IPXIP4 was added in commit 7e13318daa4a
("net: define gso types for IPx over IPv4 and IPv6", 2016-05-20),
replacing NETIF_F_GSO_IPIP and NETIF_F_GSO_SIT.
NETIF_F_GSO_IPXIP6 was added in commit bf2d1df39502 ("intel: Add support
for IPv6 IP-in-IP offload", 2016-05-20).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since the req_speeds field in struct ice_link_status is a u8,
req_speeds & ICE_AQ_LINK_SPEED_40GB always returns 0. This was caught
by a coverity scan.
Fix this by changing req_speeds to be u16.
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- hid.git is moving towards group maintainership (where group is myself
and Benjamin Tissoires), therefore this pull request updates
MAINTAINERS accordingly
- fix for hid-asus config dependency from Arnd Bergmann
- two device-specific quirks for i2c-hid from Julian Sax and Kai-Heng
Feng
- other few small assorted fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: fix up .raw_event() documentation
HID: asus: fix build warning wiht CONFIG_ASUS_WMI disabled
HID: i2c-hid: add Direkt-Tek DTLAPY133-1 to descriptor override
HID: moving to group maintainership model
HID: alps: allow incoming reports when only the trackstick is opened
Revert "HID: add NOGET quirk for Eaton Ellipse MAX UPS"
HID: i2c-hid: Add a small delay after sleep command for Raydium touchpanel
HID: hiddev: fix potential Spectre v1
|
|
drm-intel-fixes
gvt-fixes-2018-11-07
- Fix invalidate of old ggtt entry (Hang)
- Fix partial ggtt entry update in any order (Hang)
- Fix one mask setting for chicken reg (Xinyun)
- Fix eDP warning in guest (Longhe)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107023137.GO25194@zhen-hp.sh.intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Three regressions
- Revert frame counter support
. This patch fixes a issue which doesn't work extension and clone
mode because some CRTC devices don't provide frame counter value
properly.
- Fix lack of fbdev on Rinato and trats boards.
. This patch considers for connector to be registered by DSI after
DRM device is registered, and also it makes fbdev initializaion
to be done even if no connector at the moment.
- Check for dsi->panel object correctly
. This patch fixes checking for dsi->panel. of_drm_find_panel
function returns panel object or error value so error value
should be checked using IS_ERR macro.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1541407733-7632-1-git-send-email-inki.dae@samsung.com
|
|
into drm-fixes
Single etnaviv fence fix for GPU recovery.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1541522424.2508.26.camel@pengutronix.de
|
|
Causes a black screen on a Stoney laptop.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=108577
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Set the dc_config properly when the option is enabled.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add FBC to the list of features that can be enabled from the DM.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Similar to ppfeaturemask. Allows you to selectively enable/disable
DC features.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The value is dependent on whether fbc is available.
v2: only check if num_pipes is valid
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In case we need to access CLK registers.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
drm_plane_cleanup does not free the plane.
[How]
Call drm_primary_helper_destroy which will also free the plane.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
RETIMER_REDRIVER_INFO shows the buffer as a decimal value with a '0x'
prefix, which is somewhat misleading.
Fix it to print hexadecimal, as was intended.
Fixes: 2f14bc89("drm/amd/display: add retimer log for HWQ tuning use.")
Cc: Charlene Liu <charlene.liu@amd.com>
Cc: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 0cafc82fae41531b0162150f9a97f2c74f97118f.
This breaks some apps that assume 0 is minimum brightness.
Revert for 4.20. This is fixed properly for drm-next/4.21 in:
"drm/amd: Don't fail on backlight = 0"
However, that patch depends on more extensive changes to the
backlight interface which are too invasive for -fixes.
Fixes: Bugzilla: https://bugs.freedesktop.org/108668
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The timecounter needs to be updated at least once per ~550 seconds in
order to avoid a 40-bit SYSTIM timestamp to be misinterpreted as an old
timestamp.
Since commit 500462a9de65 ("timers: Switch to a non-cascading wheel"),
scheduling of delayed work seems to be less accurate and a requested
delay of 540 seconds may actually be longer than 550 seconds. Also, the
PHC may be adjusted to run up to 6% faster than real time and the system
clock up to 10% slower. Shorten the delay to 360 seconds to be sure the
timecounter is updated in time.
This fixes an issue with HW timestamps on 82580/I350/I354 being off by
~1100 seconds for few seconds every ~9 minutes.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently if the driver does a TSO offload the bytecount sent to
netdev_tx_sent_queue will be incorrect. This is because in ice_tso we
overwrite the initial value that we set in ice_tx_map. This creates a
mismatch between the Tx and Tx clean flow. In the Tx clean flow we
calculate the bytecount (called total_bytes) as we clean the
descriptors so the value used in the Tx clean path is correct. Fix this
by using += in ice_tso instead of =. This fixes the mismatch in
bytecount mentioned above.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Prior to this commit the driver was running into tx_timeouts when a
queue was stressed enough. This was happening because the HW tail
and SW tail (NTU) were incorrectly out of sync. Consequently this was
causing the HW head to collide with the HW tail, which to the hardware
means that all descriptors posted for Tx have been processed.
Due to the Tx logic used in the driver SW tail and HW tail are allowed
to be out of sync. This is done as an optimization because it allows the
driver to write HW tail as infrequently as possible, while still
updating the SW tail index to keep track. However, there are situations
where this results in the tail never getting updated, resulting in Tx
timeouts.
Tx HW tail write condition:
if (netif_xmit_stopped(txring_txq(tx_ring) || !skb->xmit_more)
writel(sw_tail, tx_ring->tail);
An issue was found in the Tx logic that was causing the afore mentioned
condition for updating HW tail to never happen, causing tx_timeouts.
In ice_xmit_frame_ring we calculate how many descriptors we need for the
Tx transaction based on the skb the kernel hands us. This is then passed
into ice_maybe_stop_tx along with some extra padding to determine if we
have enough descriptors available for this transaction. If we don't then
we return -EBUSY to the stack, otherwise we move on and eventually
prepare the Tx descriptors accordingly in ice_tx_map and set
next_to_watch. In ice_tx_map we make another call to ice_maybe_stop_tx
with a value of MAX_SKB_FRAGS + 4. The key here is that this value is
possibly less than the value we sent in the first call to
ice_maybe_stop_tx in ice_xmit_frame_ring. Now, if the number of unused
descriptors is between MAX_SKB_FRAGS + 4 and the value used in the first
call to ice_maybe_stop_tx in ice_xmit_frame_ring then we do not update
the HW tail because of the "Tx HW tail write condition" above. This is
because in ice_maybe_stop_tx we return success from ice_maybe_stop_tx
instead of calling __ice_maybe_stop_tx and subsequently calling
netif_stop_subqueue, which sets the __QUEUE_STATE_DEV_XOFF bit. This
bit is then checked in the "Tx HW tail write condition" by calling
netif_xmit_stopped and subsequently updating HW tail if the
afore mentioned bit is set.
In ice_clean_tx_irq, if next_to_watch is not NULL, we end up cleaning
the descriptors that HW sets the DD bit on and we have the budget. The
HW head will eventually run into the HW tail in response to the
description in the paragraph above.
The next time through ice_xmit_frame_ring we make the initial call to
ice_maybe_stop_tx with another skb from the stack. This time we do not
have enough descriptors available and we return NETDEV_TX_BUSY to the
stack and end up setting next_to_watch to NULL.
This is where we are stuck. In ice_clean_tx_irq we never clean anything
because next_to_watch is always NULL and in ice_xmit_frame_ring we never
update HW tail because we already return NETDEV_TX_BUSY to the stack and
eventually we hit a tx_timeout.
This issue was fixed by making sure that the second call to
ice_maybe_stop_tx in ice_tx_map is passed a value that is >= the value
that was used on the initial call to ice_maybe_stop_tx in
ice_xmit_frame_ring. This was done by adding the following defines to
make the logic more clear and to reduce the chance of mucking this up
again:
ICE_CACHE_LINE_BYTES 64
ICE_DESCS_PER_CACHE_LINE (ICE_CACHE_LINE_BYTES / \
sizeof(struct ice_tx_desc))
ICE_DESCS_FOR_CTX_DESC 1
ICE_DESCS_FOR_SKB_DATA_PTR 1
The ICE_CACHE_LINE_BYTES being 64 is an assumption being made so we
don't have to figure this out on every pass through the Tx path. Instead
I added a sanity check in ice_probe to verify cache line size and print
a message if it's not 64 Bytes. This will make it easier to file issues
if they are seen when the cache line size is not 64 Bytes when reading
from the GLPCI_CNF2 register.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the remove path, the vsi->netdev is being set to NULL before the call
to free vectors. This is causing the netif_napi_del call to never be made.
Add a call to ice_napi_del to the same location as the calls to
unregister_netdev and just prior to them. This will use the reverse flow
as the register and netif_napi_add calls.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Print should say "Enabling" instead of "Enaabling"
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
According to the spec, whenever insert PVID field is set, the VLAN
driver insertion mode should be set to 01b which isn't done currently.
Fix it.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ice_restore_vlan and active_vlans were originally put in place to
reprogram VLAN filters in the replay path. This is now done as part
of the much broader VSI rebuild/replay framework. So remove both
ice_restore_vlan and active_vlans
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the unload path, all VSIs are freed. Also free the related VSI
contexts to prevent memory leaks.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Setting Rx or Tx pause parameter currently results in link loss on the
interface, requiring the platform/host to be cold power cycled. Fix it.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The remove path does not currently check to see if a
reset is in progress before proceeding. This can cause
a resource collision resulting in various types of errors.
Check for reset in progress and wait for a reasonable
amount of time before allowing the remove to progress.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Set the carrier state post rebuild by querying the link status. Also
start/stop queues based on link status.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Mainly adding the WAFL spread spectrum info, for adjusting display
clocks when XGMI is enabled.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch allows users to enable/disable internal TX and/or RX clock
delay for BCM54616S PHYs so as to satisfy RGMII timing specifications.
On a particular platform, whether TX and/or RX clock delay is required
depends on how PHY connected to the MAC IP. This requirement can be
specified through "phy-mode" property in the platform device tree.
The patch is inspired by commit 733336262b28 ("net: phy: Allow BCM5481x
PHYs to setup internal TX/RX clock delay").
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
