| Age | Commit message (Collapse) | Author |
|---|
|
ufshcd_tmc_handler() calls blk_mq_tagset_busy_iter(fn = ufshcd_compl_tm()),
but since blk_mq_tagset_busy_iter() only iterates over all reserved tags
and requests which are not in IDLE state, ufshcd_compl_tm() never gets a
chance to run. Thus, TMR always ends up with completion timeout. Fix it by
calling blk_mq_start_request() in __ufshcd_issue_tm_cmd().
Link: https://lore.kernel.org/r/1617262750-4864-2-git-send-email-cang@codeaurora.org
Fixes: 69a6c269c097 ("scsi: ufs: Use blk_{get,put}_request() to allocate and free TMFs")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Link: https://lore.kernel.org/r/20210330071958.3788214-3-slyfox@gentoo.org
Fixes: f749d8b7a989 ("scsi: hpsa: Correct dev cmds outstanding for retried cmds")
CC: linux-ia64@vger.kernel.org
CC: storagedev@microchip.com
CC: linux-scsi@vger.kernel.org
CC: Joe Szczypek <jszczype@redhat.com>
CC: Scott Benesh <scott.benesh@microchip.com>
CC: Scott Teel <scott.teel@microchip.com>
CC: Tomas Henzl <thenzl@redhat.com>
CC: "Martin K. Petersen" <martin.petersen@oracle.com>
CC: Don Brace <don.brace@microchip.com>
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Suggested-by: Don Brace <don.brace@microchip.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Boot failure was observed on an HP rx3600 ia64 machine with RAID bus
controller: Hewlett-Packard Company Smart Array P600:
kernel unaligned access to 0xe000000105dd8b95, ip=0xa000000100b87551
kernel unaligned access to 0xe000000105dd8e95, ip=0xa000000100b87551
hpsa 0000:14:01.0: Controller reports max supported commands of 0 Using 16 instead. Ensure that firmware is up to date.
swapper/0[1]: error during unaligned kernel access
The unaligned access comes from 'struct CommandList' that happens to be
packed. Commit f749d8b7a989 ("scsi: hpsa: Correct dev cmds outstanding for
retried cmds") introduced unexpected padding and unaligned atomic_t from
natural alignment to something else.
This change removes packing annotation from a struct not intended to be
sent to controller as is. This restores natural `atomic_t` alignment.
The change was tested on the same rx3600 machine.
Link: https://lore.kernel.org/r/20210330071958.3788214-2-slyfox@gentoo.org
Fixes: f749d8b7a989 ("scsi: hpsa: Correct dev cmds outstanding for retried cmds")
CC: linux-ia64@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: storagedev@microchip.com
CC: linux-scsi@vger.kernel.org
CC: Joe Szczypek <jszczype@redhat.com>
CC: Scott Benesh <scott.benesh@microchip.com>
CC: Scott Teel <scott.teel@microchip.com>
CC: Tomas Henzl <thenzl@redhat.com>
CC: "Martin K. Petersen" <martin.petersen@oracle.com>
CC: Don Brace <don.brace@microchip.com>
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Suggested-by: Don Brace <don.brace@microchip.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The hpsa driver uses data structures which contain a combination of driver
internals and commands sent directly to the hardware. To manage alignment
for the hardware portions the driver used #pragma pack(1).
Commit f749d8b7a989 ("scsi: hpsa: Correct dev cmds outstanding for retried
cmds") switched an existing variable from int to bool. Due to the pragma an
atomic_t in the same data structure ended up being misaligned and broke
boot on ia64.
Add __packed to every struct and union in the header file. Subsequent
commits will address the actual atomic_t misalignment regression.
The commit is a no-op at least on ia64:
$ diff -u <(objdump -d -r old.o) <(objdump -d -r new.o)
Link: https://lore.kernel.org/r/20210330071958.3788214-1-slyfox@gentoo.org
Fixes: f749d8b7a989 ("scsi: hpsa: Correct dev cmds outstanding for retried cmds")
CC: linux-ia64@vger.kernel.org
CC: storagedev@microchip.com
CC: linux-scsi@vger.kernel.org
CC: Joe Szczypek <jszczype@redhat.com>
CC: Scott Benesh <scott.benesh@microchip.com>
CC: Scott Teel <scott.teel@microchip.com>
CC: Tomas Henzl <thenzl@redhat.com>
CC: "Martin K. Petersen" <martin.petersen@oracle.com>
CC: Don Brace <don.brace@microchip.com>
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Suggested-by: Don Brace <don.brace@microchip.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A kernel panic was observed due to a timing issue between the sync thread
and the initiator processing a login response from the target. The session
reopen can be invoked both from the session sync thread when iscsid
restarts and from iscsid through the error handler. Before the initiator
receives the response to a login, another reopen request can be sent from
the error handler/sync session. When the initial login response is
subsequently processed, the connection has been closed and the socket has
been released.
To fix this a new connection state, ISCSI_CONN_BOUND, is added:
- Set the connection state value to ISCSI_CONN_DOWN upon
iscsi_if_ep_disconnect() and iscsi_if_stop_conn()
- Set the connection state to the newly created value ISCSI_CONN_BOUND
after bind connection (transport->bind_conn())
- In iscsi_set_param(), return -ENOTCONN if the connection state is not
either ISCSI_CONN_BOUND or ISCSI_CONN_UP
Link: https://lore.kernel.org/r/20210325093248.284678-1-gulam.mohamed@oracle.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Gulam Mohamed <gulam.mohamed@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
index 91074fd97f64..f4bf62b007a0 100644
|
|
If pscsi_map_sg() fails, make sure to drop references to already allocated
bios.
Link: https://lore.kernel.org/r/20210323212431.15306-2-mwilck@suse.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
pscsi_map_sg() uses the variable nr_pages as a hint for bio_kmalloc() how
many vector elements to allocate. If nr_pages is < BIO_MAX_PAGES, it will
be reset to 0 after successful allocation of the bio.
If bio_add_pc_page() fails later for whatever reason, pscsi_map_sg() tries
to allocate another bio, passing nr_vecs = 0. This causes bio_add_pc_page()
to fail immediately in the next call. pci_map_sg() continues to allocate
zero-length bios until memory is exhausted and the kernel crashes with
OOM. This can be easily observed by exporting a SATA DVD drive via pscsi.
The target crashes as soon as the client tries to access the DVD LUN. In
the case I analyzed, bio_add_pc_page() would fail because the DVD device's
max_sectors_kb (128) was exceeded.
Avoid this by simply not resetting nr_pages to 0 after allocating the
bio. This way, the client receives an I/O error when it tries to send
requests exceeding the devices max_sectors_kb, and eventually gets it
right. The client must still limit max_sectors_kb e.g. by an udev rule if
(like in my case) the driver doesn't report valid block limits, otherwise
it encounters I/O errors.
Link: https://lore.kernel.org/r/20210323212431.15306-1-mwilck@suse.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When kzalloc() returns NULL, no error return code of mpt3sas_base_attach()
is assigned. To fix this bug, r is assigned with -ENOMEM in this case.
Link: https://lore.kernel.org/r/20210308035241.3288-1-baijiaju1990@gmail.com
Fixes: c696f7b83ede ("scsi: mpt3sas: Implement device_remove_in_progress check in IOCTL path")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When kzalloc() returns NULL to qedi->global_queues[i], no error return code
of qedi_alloc_global_queues() is assigned. To fix this bug, status is
assigned with -ENOMEM in this case.
Link: https://lore.kernel.org/r/20210308033024.27147-1-baijiaju1990@gmail.com
Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Calling vha->hw->tgt.tgt_ops->free_cmd() from qlt_xmit_response() is wrong
since the command for which a response is sent must remain valid until the
SCSI target core calls .release_cmd(). It has been observed that the
following scenario triggers a kernel crash:
- qlt_xmit_response() calls qlt_check_reserve_free_req()
- qlt_check_reserve_free_req() returns -EAGAIN
- qlt_xmit_response() calls vha->hw->tgt.tgt_ops->free_cmd(cmd)
- transport_handle_queue_full() tries to retransmit the response
Fix this crash by reverting the patch that introduced it.
Link: https://lore.kernel.org/r/20210320232359.941-2-bvanassche@acm.org
Fixes: 0dcec41acb85 ("scsi: qla2xxx: Make sure that aborted commands are freed")
Cc: Quinn Tran <qutran@marvell.com>
Cc: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During MQ enablement of the ibmvfc driver ibmvfc_wait_for_ops() was
missed. This function is responsible for waiting on commands to complete
that match a certain criteria such as LUN or cancel key. The implementation
as is only scans the CRQ for events ignoring any sub-queues and as a result
will exit successfully without doing anything when operating in MQ
channelized mode.
Check the MQ and channel use flags to determine which queues are
applicable, and scan each queue accordingly. Note in MQ mode SCSI commands
are only issued down sub-queues and the CRQ is only used for driver
specific management commands. As such the CRQ events are ignored when
operating in MQ mode with channels.
Link: https://lore.kernel.org/r/20210319205029.312969-3-tyreld@linux.ibm.com
Fixes: 9000cb998bcf ("scsi: ibmvfc: Enable MQ and set reasonable defaults")
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For various EH activities the ibmvfc driver uses ibmvfc_wait_for_ops() to
wait for the completion of commands that match a given criteria be it
cancel key, or specific LUN. With recent changes commands are completed
outside the lock in bulk by removing them from the sent list and adding
them to a private completion list. This introduces a potential race in
ibmvfc_wait_for_ops() since the criteria for a command to be outstanding is
no longer simply being on the sent list, but instead not being on the free
list.
Avoid this race by scanning the entire command event pool and checking that
any matching command that ibmvfc needs to wait on is not already on the
free list.
Link: https://lore.kernel.org/r/20210319205029.312969-2-tyreld@linux.ibm.com
Fixes: 1f4a4a19508d ("scsi: ibmvfc: Complete commands outside the host/queue lock")
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
mpt3sas_get_port_by_id() can be called when a spinlock is held. Use
GFP_ATOMIC instead of GFP_KERNEL when allocating memory.
Issue spotted by call_kern.cocci:
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 7125 inside lock on line 7123 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 6842 inside lock on line 6839 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 6854 inside lock on line 6851 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 7706 inside lock on line 7702 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 10260 inside lock on line 10256 but uses GFP_KERNEL
Link: https://lore.kernel.org/r/20210220093951.905362-1-christophe.jaillet@wanadoo.fr
Fixes: 324c122fc0a4 ("scsi: mpt3sas: Add module parameter multipath_on_hba")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The "lpm" and "->enabled" are all boolean. We should be using &&
rather than the bit operator.
Link: https://lore.kernel.org/r/1615896915-148864-1-git-send-email-dj0227@163.com
Fixes: 488edafb1120 ("scsi: ufs-mediatek: Introduce low-power mode for device power supply")
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: dongjian <dongjian@yulong.com>
Signed-off-by: Yue Hu <huyue2@yulong.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Recent changes changed the completion of SCSI commands from Soft-IRQ
context to IRQ context. This triggers the following warning, when we're
completing writes to zoned block devices that go through the zone append
emulation:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.12.0-rc2+ #2
Hardware name: Supermicro Super Server/X10SRL-F, BIOS 2.0 12/17/2015
RIP: 0010:__local_bh_disable_ip+0x3f/0x50
RSP: 0018:ffff8883e1409ba8 EFLAGS: 00010006
RAX: 0000000080010001 RBX: 0000000000000001 RCX: 0000000000000013
RDX: ffff888129e4d200 RSI: 0000000000000201 RDI: ffffffff915b9dbd
RBP: ffff888113e9a540 R08: ffff888113e9a540 R09: 00000000000077f0
R10: 0000000000080000 R11: 0000000000000001 R12: ffff888129e4d200
R13: 0000000000001000 R14: 00000000000077f0 R15: ffff888129e4d218
FS: 0000000000000000(0000) GS:ffff8883e1400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f2f8418ebc0 CR3: 000000021202a006 CR4: 00000000001706f0
Call Trace:
<IRQ>
_raw_spin_lock_bh+0x18/0x40
sd_zbc_complete+0x43d/0x1150
sd_done+0x631/0x1040
? mark_lock+0xe4/0x2fd0
? provisioning_mode_store+0x3f0/0x3f0
scsi_finish_command+0x31b/0x5c0
_scsih_io_done+0x960/0x29e0 [mpt3sas]
? mpt3sas_scsih_scsi_lookup_get+0x1c7/0x340 [mpt3sas]
? __lock_acquire+0x166b/0x58b0
? _get_st_from_smid+0x4a/0x80 [mpt3sas]
_base_process_reply_queue+0x23f/0x26e0 [mpt3sas]
? lock_is_held_type+0x98/0x110
? find_held_lock+0x2c/0x110
? mpt3sas_base_sync_reply_irqs+0x360/0x360 [mpt3sas]
_base_interrupt+0x8d/0xd0 [mpt3sas]
? rcu_read_lock_sched_held+0x3f/0x70
__handle_irq_event_percpu+0x24d/0x600
handle_irq_event+0xef/0x240
? handle_irq_event_percpu+0x110/0x110
handle_edge_irq+0x1f6/0xb60
__common_interrupt+0x75/0x160
common_interrupt+0x7b/0xa0
</IRQ>
asm_common_interrupt+0x1e/0x40
Don't use spin_lock_bh() to protect the update of the write pointer offset
cache, but use spin_lock_irqsave() for it.
Link: https://lore.kernel.org/r/3cfebe48d09db73041b7849be71ffbcec7ee40b3.1615369586.git.johannes.thumshirn@wdc.com
Fixes: 664f0dce2058 ("scsi: mpt3sas: Add support for shared host tagset for CPU hotplug")
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If copy_from_user() or kstrtoull() fail then the correct behavior is to
return a negative error code.
Link: https://lore.kernel.org/r/YEsbU/UxYypVrC7/@mwanda
Fixes: f9bb2da11db8 ("[SCSI] lpfc 8.3.27: T10 additions for SLI4")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Only half of the file is under include guard because terminating #endif
is placed too early.
Link: https://lore.kernel.org/r/YE4snvoW1SuwcXAn@localhost.localdomain
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In st_open(), if STp->in_use is true, STp will be freed by
scsi_tape_put(). However, STp is still used by DEBC_printk() after. It is
better to DEBC_printk() before scsi_tape_put().
Link: https://lore.kernel.org/r/20210311064636.10522-1-lyl2019@mail.ustc.edu.cn
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In myrs_cleanup(), cs->mmio_base will be freed twice by iounmap().
Link: https://lore.kernel.org/r/20210311063005.9963-1-lyl2019@mail.ustc.edu.cn
Fixes: 77266186397c ("scsi: myrs: Add Mylex RAID controller (SCSI interface)")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The buffer for negotiating channel setup is DMA allocated at device probe
time. However, the remove path fails to free this allocation which will
prevent the hypervisor from releasing the virtual device in the case of a
hotplug remove.
Fix this issue by freeing the buffer allocation in ibmvfc_free_mem().
Link: https://lore.kernel.org/r/20210311012212.428068-1-tyreld@linux.ibm.com
Fixes: e95eef3fc0bc ("scsi: ibmvfc: Implement channel enquiry and setup commands")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The entries in the source files are removed as well.
Link: https://lore.kernel.org/r/20210226234347.21535-1-vbhakta@vmware.com
Signed-off-by: Vishal Bhakta <vbhakta@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix the following coccicheck warning:
./drivers/scsi/ufs/ufshcd.c:1538:8-16: WARNING: use scnprintf or
sprintf.
Link: https://lore.kernel.org/r/1614665298-115183-1-git-send-email-jiapeng.chong@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Runtime and system suspend/resume can only come after hba probe invokes
platform_set_drvdata(pdev, hba), meaning hba cannot be NULL in these PM
callbacks, so remove the checks of !hba.
Link: https://lore.kernel.org/r/1614145010-36079-4-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Disable interrupt in reset path to flush pending IRQ handler in order to
avoid possible NoC issues.
Link: https://lore.kernel.org/r/1614145010-36079-3-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Nitin Rawat <nitirawa@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In error handling prepare stage, after SCSI requests are blocked, do a
down/up_write(clk_scaling_lock) to clean up the queuecommand() path.
Meanwhile, stop eeh_work in case it disturbs error recovery. Moreover,
reset ufshcd_state at the entrance of ufshcd_probe_hba(), since it may be
called multiple times during error recovery.
Link: https://lore.kernel.org/r/1614145010-36079-2-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A live partition migration (LPM) results in a CRQ disconnect similar to a
hard reset. In this LPM case the hypervisor mostly preserves the CRQ
transport such that it simply needs to be reenabled. However, the
capabilities may have changed such as fewer channels, or no channels at
all. Further, its possible that there may be sub-CRQ support, but no
channel support. The CRQ reenable path currently doesn't take any of this
into consideration.
For simplicity release and reinitialize sub-CRQs during reenable, and set
do_enquiry and using_channels with the appropriate values to trigger
channel renegotiation.
Link: https://lore.kernel.org/r/20210302230543.9905-6-tyreld@linux.ibm.com
Fixes: 3034ebe26389 ("scsi: ibmvfc: Add alloc/dealloc routines for SCSI Sub-CRQ Channels")
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The H_FREE_SUB_CRQ hypercall can return a retry delay return code that
indicates the call needs to be retried after a specific amount of time
delay. The error path to free a sub-CRQ in case of a failure during channel
registration fails to capture the return code of H_FREE_SUB_CRQ which will
result in the delay loop being skipped in the case of a retry delay return
code.
Store the return code result of the H_FREE_SUB_CRQ call such that the
return code check in the delay loop evaluates a meaningful value. Also, use
the rtas_busy_delay() to check the rc value and delay for the appropriate
amount of time.
Link: https://lore.kernel.org/r/20210302230543.9905-5-tyreld@linux.ibm.com
Fixes: 39e461fddff0 ("scsi: ibmvfc: Map/request irq and register Sub-CRQ interrupt handler")
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A non-zero return code for H_REG_SUB_CRQ is currently treated as a failure
resulting in failing sub-CRQ setup. The case of H_CLOSED should not be
treated as a failure. This return code translates to a successful sub-CRQ
registration by the hypervisor, and is meant to communicate back that there
is currently no partner VIOS CRQ connection established as of yet. This is
a common occurrence during a disconnect where the client adapter can
possibly come back up prior to the partner adapter.
For non-zero return code from H_REG_SUB_CRQ treat a H_CLOSED as success so
that sub-CRQs are successfully setup.
Link: https://lore.kernel.org/r/20210302230543.9905-4-tyreld@linux.ibm.com
Fixes: 3034ebe26389 ("scsi: ibmvfc: Add alloc/dealloc routines for SCSI Sub-CRQ Channels")
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A hard reset results in a complete transport disconnect such that the CRQ
connection with the partner VIOS is broken. This has the side effect of
also invalidating the associated sub-CRQs. The current code assumes that
the sub-CRQs are perserved resulting in a protocol violation after trying
to reconnect them with the VIOS. This introduces an infinite loop such that
the VIOS forces a disconnect after each subsequent attempt to re-register
with invalid handles.
Avoid the aforementioned issue by releasing the sub-CRQs prior to CRQ
disconnect, and driving a reinitialization of the sub-CRQs once a new CRQ
is registered with the hypervisor.
Link: https://lore.kernel.org/r/20210302230543.9905-3-tyreld@linux.ibm.com
Fixes: 3034ebe26389 ("scsi: ibmvfc: Add alloc/dealloc routines for SCSI Sub-CRQ Channels")
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If ibmvfc_init_sub_crqs() fails ibmvfc_probe() simply parrots registration
failure reported elsewhere, and futher vhost->scsi_scrq.scrq == NULL is
indication enough to the driver that it has no sub-CRQs available. The
mq_enabled check can also be moved into ibmvfc_init_sub_crqs() such that
each caller doesn't have to gate the call with a mq_enabled check. Finally,
in the case of sub-CRQ setup failure setting do_enquiry can be turned off
to putting the driver into single queue fallback mode.
The aforementioned changes also simplify the next patch in the series that
fixes a hard reset issue, by tying a sub-CRQ setup failure and do_enquiry
logic into ibmvfc_init_sub_crqs().
Link: https://lore.kernel.org/r/20210302230543.9905-2-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull ide fix from Jens Axboe:
"This is a leftover fix from 5.11, where I forgot to ship it your way"
* tag 'ide-5.11-2021-02-28' of git://git.kernel.dk/linux-block:
ide/falconide: Fix module unload
|
|
Pull more SCSI updates from James Bottomley:
"This is a few driver updates (iscsi, mpt3sas) that were still in the
staging queue when the merge window opened (all committed on or before
8 Feb) and some small bug fixes which came in during the merge window
(all committed on 22 Feb)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (30 commits)
scsi: hpsa: Correct dev cmds outstanding for retried cmds
scsi: sd: Fix Opal support
scsi: target: tcmu: Fix memory leak caused by wrong uio usage
scsi: target: tcmu: Move some functions without code change
scsi: sd: sd_zbc: Don't pass GFP_NOIO to kvcalloc
scsi: aic7xxx: Remove unused function pointer typedef ahc_bus_suspend/resume_t
scsi: bnx2fc: Fix Kconfig warning & CNIC build errors
scsi: ufs: Fix a duplicate dev quirk number
scsi: aic79xx: Fix spelling of version
scsi: target: core: Prevent underflow for service actions
scsi: target: core: Add cmd length set before cmd complete
scsi: iscsi: Drop session lock in iscsi_session_chkready()
scsi: qla4xxx: Use iscsi_is_session_online()
scsi: libiscsi: Reset max/exp cmdsn during recovery
scsi: iscsi_tcp: Fix shost can_queue initialization
scsi: libiscsi: Add helper to calculate max SCSI cmds per session
scsi: libiscsi: Fix iSCSI host workq destruction
scsi: libiscsi: Fix iscsi_task use after free()
scsi: libiscsi: Drop taskqueuelock
scsi: libiscsi: Fix iscsi_prep_scsi_cmd_pdu() error handling
...
|
|
Pull more block updates from Jens Axboe:
"A few stragglers (and one due to me missing it originally), and fixes
for changes in this merge window mostly. In particular:
- blktrace cleanups (Chaitanya, Greg)
- Kill dead blk_pm_* functions (Bart)
- Fixes for the bio alloc changes (Christoph)
- Fix for the partition changes (Christoph, Ming)
- Fix for turning off iopoll with polled IO inflight (Jeffle)
- nbd disconnect fix (Josef)
- loop fsync error fix (Mauricio)
- kyber update depth fix (Yang)
- max_sectors alignment fix (Mikulas)
- Add bio_max_segs helper (Matthew)"
* tag 'block-5.12-2021-02-27' of git://git.kernel.dk/linux-block: (21 commits)
block: Add bio_max_segs
blktrace: fix documentation for blk_fill_rw()
block: memory allocations in bounce_clone_bio must not fail
block: remove the gfp_mask argument to bounce_clone_bio
block: fix bounce_clone_bio for passthrough bios
block-crypto-fallback: use a bio_set for splitting bios
block: fix logging on capacity change
blk-settings: align max_sectors on "logical_block_size" boundary
block: reopen the device in blkdev_reread_part
block: don't skip empty device in in disk_uevent
blktrace: remove debugfs file dentries from struct blk_trace
nbd: handle device refs for DESTROY_ON_DISCONNECT properly
kyber: introduce kyber_depth_updated()
loop: fix I/O error on fsync() in detached loop devices
block: fix potential IO hang when turning off io_poll
block: get rid of the trace rq insert wrapper
blktrace: fix blk_rq_merge documentation
blktrace: fix blk_rq_issue documentation
blktrace: add blk_fill_rwbs documentation comment
block: remove superfluous param in blk_fill_rwbs()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs updates from Al Viro:
"Assorted stuff pile - no common topic here"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
whack-a-mole: don't open-code iminor/imajor
9p: fix misuse of sscanf() in v9fs_stat2inode()
audit_alloc_mark(): don't open-code ERR_CAST()
fs/inode.c: make inode_init_always() initialize i_ino to 0
vfs: don't unnecessarily clone write access for writable fds
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Three more bugfixes and one revert. I accidently applied one patch too
early"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: exynos5: Preserve high speed master code
Revert "i2c: i2c-qcom-geni: Add shutdown callback for i2c"
i2c: designware: Get right data length
i2c: brcmstb: Fix brcmstd_send_i2c_cmd condition
|
|
It's often inconvenient to use BIO_MAX_PAGES due to min() requiring the
sign to be the same. Introduce bio_max_segs() and change BIO_MAX_PAGES to
be unsigned to make it easier for the users.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull documentation fixes from Jonathan Corbet:
"A handful of late-arriving documentation fixes, nothing all that
notable"
* tag 'docs-5.12-2' of git://git.lwn.net/linux:
docs: proc.rst: fix indentation warning
Documentation: cgroup-v2: fix path to example BPF program
docs: powerpc: Fix tables in syscall64-abi.rst
Documentation: features: refresh feature list
Documentation: features: remove c6x references
docs: ABI: testing: ima_policy: Fixed missing bracket
Fix unaesthetic indentation
scripts: kernel-doc: fix array element capture in pointer-to-func parsing
doc: use KCFLAGS instead of EXTRA_CFLAGS to pass flags from command line
Documentation: proc.rst: add more about the 6 fields in loadavg
|
|
Pull OpenRISC updates from Stafford Horne:
- Update for Litex SoC controller to support wider width registers as
well as reset.
- Refactor SMP code to use device tree to define possible cpus.
- Update build including generating vmlinux.bin
* tag 'for-linus' of git://github.com/openrisc/linux:
openrisc: Use devicetree to determine present cpus
drivers/soc/litex: Add restart handler
openrisc: add arch/openrisc/Kbuild
drivers/soc/litex: make 'litex_[set|get]_reg()' methods private
drivers/soc/litex: support 32-bit subregisters, 64-bit CPUs
drivers/soc/litex: s/LITEX_REG_SIZE/LITEX_SUBREG_ALIGN/g
drivers/soc/litex: separate MMIO from subregister offset calculation
drivers/soc/litex: move generic accessors to litex.h
openrisc: restart: Call common handlers before hanging
openrisc: Add vmlinux.bin target
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Vasily Gorbik:
- Fix physical vs virtual confusion in some basic mm macros and
routines. Caused by __pa == __va on s390 currently.
- Get rid of on-stack cpu masks.
- Add support for complete CPU counter set extraction.
- Add arch_irq_work_raise implementation.
- virtio-ccw revision and opcode fixes.
* tag 's390-5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cpumf: Add support for complete counter set extraction
virtio/s390: implement virtio-ccw revision 2 correctly
s390/smp: implement arch_irq_work_raise()
s390/topology: move cpumasks away from stack
s390/smp: smp_emergency_stop() - move cpumask away from stack
s390/smp: __smp_rescan_cpus() - move cpumask away from stack
s390/smp: consolidate locking for smp_rescan()
s390/mm: fix phys vs virt confusion in vmem_*() functions family
s390/mm: fix phys vs virt confusion in pgtable allocation routines
s390/mm: fix invalid __pa() usage in pfn_pXd() macros
s390/mm: make pXd_deref() macros return a pointer
s390/opcodes: rename selhhhr to selfhr
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb
Pull swiotlb updates from Konrad Rzeszutek Wilk:
"Two memory encryption related patches (SWIOTLB is enabled by default
for AMD-SEV):
- Add support for alignment so that NVME can properly work
- Keep track of requested DMA buffers length, as underlaying hardware
devices can trip SWIOTLB to bounce too much and crash the kernel
And a tiny fix to use proper APIs in drivers"
* 'stable/for-linus-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: Validate bounce size in the sync/unmap path
nvme-pci: set min_align_mask
swiotlb: respect min_align_mask
swiotlb: don't modify orig_addr in swiotlb_tbl_sync_single
swiotlb: refactor swiotlb_tbl_map_single
swiotlb: clean up swiotlb_tbl_unmap_single
swiotlb: factor out a nr_slots helper
swiotlb: factor out an io_tlb_offset helper
swiotlb: add a IO_TLB_SIZE define
driver core: add a min_align_mask field to struct device_dma_parameters
sdhci: stop poking into swiotlb internals
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"Besides the usual fixes and new drivers, we are changing CLASS_FLASH
to return success to make it easier to work with V4L2 stuff disabled,
and we are getting rid of enum that should have been plain integer
long time ago. I'm slightly nervous about potential warnings, but it
needed to be fixed at some point"
* tag 'leds-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: lp50xx: Get rid of redundant explicit casting
leds: lp50xx: Update headers block to reflect reality
leds: lp50xx: Get rid of redundant check in lp50xx_enable_disable()
leds: lp50xx: Reduce level of dereferences
leds: lp50xx: Switch to new style i2c-driver probe function
leds: lp50xx: Don't spam logs when probe is deferred
leds: apu: extend support for PC Engines APU1 with newer firmware
leds: flash: Fix multicolor no-ops registration by return 0
leds: flash: Add flash registration with undefined CONFIG_LEDS_CLASS_FLASH
leds: lgm: Add LED controller driver for LGM SoC
dt-bindings: leds: Add bindings for Intel LGM SoC
leds: led-core: Get rid of enum led_brightness
leds: gpio: Set max brightness to 1
leds: lm3533: Switch to using the new API kobj_to_dev()
leds: ss4200: simplify the return expression of register_nasgpio_led()
leds: Use DEVICE_ATTR_{RW, RO, WO} macros
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux
Pull pcmcia update from Dominik Brodowski:
"Improve the use of the kobj API in the core of the Linux PCMCIA
subsystem"
* 'pcmcia-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
pcmcia: Switch to using the new API kobj_to_dev()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
"A handful of new RISC-V related patches for this merge window:
- A check to ensure drivers are properly using uaccess. This isn't
manifesting with any of the drivers I'm currently using, but may
catch errors in new drivers.
- Some preliminary support for the FU740, along with the HiFive
Unleashed it will appear on.
- NUMA support for RISC-V, which involves making the arm64 code
generic.
- Support for kasan on the vmalloc region.
- A handful of new drivers for the Kendryte K210, along with the DT
plumbing required to boot on a handful of K210-based boards.
- Support for allocating ASIDs.
- Preliminary support for kernels larger than 128MiB.
- Various other improvements to our KASAN support, including the
utilization of huge pages when allocating the KASAN regions.
We may have already found a bug with the KASAN_VMALLOC code, but it's
passing my tests. There's a fix in the works, but that will probably
miss the merge window.
* tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (75 commits)
riscv: Improve kasan population by using hugepages when possible
riscv: Improve kasan population function
riscv: Use KASAN_SHADOW_INIT define for kasan memory initialization
riscv: Improve kasan definitions
riscv: Get rid of MAX_EARLY_MAPPING_SIZE
soc: canaan: Sort the Makefile alphabetically
riscv: Disable KSAN_SANITIZE for vDSO
riscv: Remove unnecessary declaration
riscv: Add Canaan Kendryte K210 SD card defconfig
riscv: Update Canaan Kendryte K210 defconfig
riscv: Add Kendryte KD233 board device tree
riscv: Add SiPeed MAIXDUINO board device tree
riscv: Add SiPeed MAIX GO board device tree
riscv: Add SiPeed MAIX DOCK board device tree
riscv: Add SiPeed MAIX BiT board device tree
riscv: Update Canaan Kendryte K210 device tree
dt-bindings: add resets property to dw-apb-timer
dt-bindings: fix sifive gpio properties
dt-bindings: update sifive uart compatible string
dt-bindings: update sifive clint compatible string
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- A small series for Xen event channels adding some sysfs nodes for per
pv-device settings and statistics, and two fixes of theoretical
problems.
- two minor fixes (one for an unlikely error path, one for a comment).
* tag 'for-linus-5.12b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen-front-pgdir-shbuf: don't record wrong grant handle upon error
xen: Replace lkml.org links with lore
xen/evtchn: use READ/WRITE_ONCE() for accessing ring indices
xen/evtchn: use smp barriers for user event ring
xen/events: add per-xenbus device event statistics and settings
|
|
Merge more updates from Andrew Morton:
"118 patches:
- The rest of MM.
Includes kfence - another runtime memory validator. Not as thorough
as KASAN, but it has unmeasurable overhead and is intended to be
usable in production builds.
- Everything else
Subsystems affected by this patch series: alpha, procfs, sysctl,
misc, core-kernel, MAINTAINERS, lib, bitops, checkpatch, init,
coredump, seq_file, gdb, ubsan, initramfs, and mm (thp, cma,
vmstat, memory-hotplug, mlock, rmap, zswap, zsmalloc, cleanups,
kfence, kasan2, and pagemap2)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
MIPS: make userspace mapping young by default
initramfs: panic with memory information
ubsan: remove overflow checks
kgdb: fix to kill breakpoints on initmem after boot
scripts/gdb: fix list_for_each
x86: fix seq_file iteration for pat/memtype.c
seq_file: document how per-entry resources are managed.
fs/coredump: use kmap_local_page()
init/Kconfig: fix a typo in CC_VERSION_TEXT help text
init: clean up early_param_on_off() macro
init/version.c: remove Version_<LINUX_VERSION_CODE> symbol
checkpatch: do not apply "initialise globals to 0" check to BPF progs
checkpatch: don't warn about colon termination in linker scripts
checkpatch: add kmalloc_array_node to unnecessary OOM message check
checkpatch: add warning for avoiding .L prefix symbols in assembly files
checkpatch: improve TYPECAST_INT_CONSTANT test message
checkpatch: prefer ftrace over function entry/exit printks
checkpatch: trivial style fixes
checkpatch: ignore warning designated initializers using NR_CPUS
checkpatch: improve blank line after declaration test
...
|
|
Update contact info.
Link: https://lkml.kernel.org/r/20210206162524.GA11520@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There exists multiple path may do zram compaction concurrently.
1. auto-compaction triggered during memory reclaim
2. userspace utils write zram<id>/compaction node
So, multiple threads may call zs_shrinker_scan/zs_compact concurrently.
But pages_compacted is a per zsmalloc pool variable and modification
of the variable is not serialized(through under class->lock).
There are two issues here:
1. the pages_compacted may not equal to total number of pages
freed(due to concurrently add).
2. zs_shrinker_scan may not return the correct number of pages
freed(issued by current shrinker).
The fix is simple:
1. account the number of pages freed in zs_compact locally.
2. use actomic variable pages_compacted to accumulate total number.
Link: https://lkml.kernel.org/r/20210202122235.26885-1-wu-yan@tcl.com
Fixes: 860c707dca155a56 ("zsmalloc: account the number of compacted pages")
Signed-off-by: Rokudo Yan <wu-yan@tcl.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Right now, we only check against MAX_PHYSMEM_BITS - but turns out there
are more restrictions of which memory we can actually hotplug, especially
om arm64 or s390x once we support them: we might receive something like
-E2BIG or -ERANGE from add_memory_driver_managed(), stopping device
operation.
So, check right when initializing the device which memory we can add,
warning the user. Try only adding actually pluggable ranges: in the worst
case, no memory provided by our device is pluggable.
In the usual case, we expect all device memory to be pluggable, and in
corner cases only some memory at the end of the device-managed memory
region to not be pluggable.
Link: https://lkml.kernel.org/r/1612149902-7867-5-git-send-email-anshuman.khandual@arm.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: teawater <teawaterz@linux.alibaba.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Pankaj Gupta <pankaj.gupta@cloud.ionos.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
No need to store the value for each and every memory block, as we can
easily query the value at runtime. Reshuffle the members to optimize the
memory layout. Also, let's clarify what the interface once was used for
and why it's legacy nowadays.
"phys_device" was used on s390x in older versions of lsmem[2]/chmem[3],
back when they were still part of s390x-tools. They were later replaced
by the variants in linux-utils. For example, RHEL6 and RHEL7 contain
lsmem/chmem from s390-utils. RHEL8 switched to versions from util-linux
on s390x [4].
"phys_device" was added with sysfs support for memory hotplug in commit
3947be1969a9 ("[PATCH] memory hotplug: sysfs and add/remove functions") in
2005. It always returned 0.
s390x started returning something != 0 on some setups (if sclp.rzm is set
by HW) in 2010 via commit 57b552ba0b2f ("memory hotplug/s390: set
phys_device").
For s390x, it allowed for identifying which memory block devices belong to
the same storage increment (RZM). Only if all memory block devices
comprising a single storage increment were offline, the memory could
actually be removed in the hypervisor.
Since commit e5d709bb5fb7 ("s390/memory hotplug: provide
memory_block_size_bytes() function") in 2013 a memory block device spans
at least one storage increment - which is why the interface isn't really
helpful/used anymore (except by old lsmem/chmem tools).
There were once RFC patches to make use of "phys_device" in ACPI context;
however, the underlying problem could be solved using different interfaces
[1].
[1] https://patchwork.kernel.org/patch/2163871/
[2] https://github.com/ibm-s390-tools/s390-tools/blob/v2.1.0/zconf/lsmem
[3] https://github.com/ibm-s390-tools/s390-tools/blob/v2.1.0/zconf/chmem
[4] https://bugzilla.redhat.com/show_bug.cgi?id=1504134
Link: https://lkml.kernel.org/r/20210201181347.13262-2-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Vaibhav Jain <vaibhav@linux.ibm.com>
Cc: Tom Rix <trix@redhat.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Let's make "MEMHP_MERGE_RESOURCE" consistent with "MHP_NONE", "mhp_t" and
"mhp_flags". As discussed recently [1], "mhp" is our internal acronym for
memory hotplug now.
[1] https://lore.kernel.org/linux-mm/c37de2d0-28a1-4f7d-f944-cfd7d81c334d@redhat.com/
Link: https://lkml.kernel.org/r/20210126115829.10909-1-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Wei Liu <wei.liu@kernel.org>
Reviewed-by: Pankaj Gupta <pankaj.gupta@cloud.ionos.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
