Age | Commit message (Collapse) | Author |
|
The SGE Host Page Size has nothing to do with the actual
Host Page Size. It's the SGE's BAR2 Doorbell/GTS Page Size
for interpreting the SGE Ingress/Egress Queue per Page values.
Firmware reads all of these things and makes all the
subsequent changes necessary. The Host Driver uses the SGE
Host Page Size in order to properly calculate BAR2 Offsets.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of constantly playing with the struct initializer
syntax trying to make gcc and CLang both happy, just clear
it out using memset().
>> drivers/net/tun.c:2503:42: warning: Using plain integer as NULL pointer
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thanks to the batched XDP buffs through msg_control. Instead of
calling put_page() for each page which involves a atomic operation,
let's batch them by record the last page that needs to be freed and
its refcnt count and free them in a batch.
Testpmd(virtio-user + vhost_net) + XDP_DROP shows 3.8% improvement.
Before: 4.71Mpps
After : 4.89Mpps
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We do a get_page() which involves a atomic operation. This patch tries
to mitigate a per packet atomic operation by maintaining a reference
bias which is initially USHRT_MAX. Each time a page is got, instead of
calling get_page() we decrease the bias and when we find it's time to
use a new page we will decrease the bias at one time through
__page_cache_drain_cache().
Testpmd(virtio_user + vhost_net) + XDP_DROP on TAP shows about 1.6%
improvement.
Before: 4.63Mpps
After: 4.71Mpps
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/isdn/hisax/hfc_pci.c:277:6: warning:
variable ‘total’ set but not used [-Wunused-but-set-variable]
It never used since git history start.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The manual states that the checksum cannot lie in the last DWORD of the
transmission, so add a basic check for this and fall back to software
checksumming the packet.
This only seems to trigger for ACK packets with no options or data to
return to the other end, and the use of the tx-alignment option makes
it more likely to happen.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the RX code to use get_unaligned_le32() instead of the combo
of memcpy and cpu_to_le32s(&var).
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The smsc95xx_tx_fixup is doing multiple calls to skb_push() to
put an 8-byte command header onto the packet. It would be easier
to do one skb_push() and then copy the data in once the push is
done.
We also make the code smaller by using proper unaligned puts for
the header. This merges in the CPU to LE32 conversion as well and
makes the whole sequence easier to understand hopefully.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The smsc95xx driver already takes into account the NET_IP_ALIGN
parameter when setting up the receive packet data, which means
we do not need to worry about aligning the packets in the usbnet
driver.
Adding the EVENT_NO_IP_ALIGN means that the IPv4 header is now
passed to the ip_rcv() routine with the start on an aligned address.
Tested on Raspberry Pi B3.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for byte queue limit.
On NAPI poll, we save the total number of Tx confirmed frames/bytes
and register them with bql at the end of the poll function.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the frame consume callback signature:
* the entire FQ structure is passed to the callback instead
of just the queue index
* the NAPI structure can be easily obtained from the channel
it is associated to, so we don't need to pass it explicitly
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DPNI object on which we build a network interface has a
certain number of {Rx, Tx, Tx confirmation} frame queues as
resources. The default hardware setup offers one queue of each
type, as well as one DPCON channel, for each core available
in the system.
There are however cases where the number of queues is greater
than the number of cores or channels. Until now, we configured
and used all the frame queues associated with a DPNI, even if it
meant assigning multiple queues of one type to the same channel.
Update the driver to only use a number of queues equal to the
number of channels, ensuring each channel will contain exactly
one Rx and one Tx confirmation queue.
>From the user viewpoint, this change is completely transparent.
Performance wise there is no impact in most scenarios. In case
the number of queues is larger than and not a multiple of the
number of channels, Rx hash distribution offers now better load
balancing between cores, which can have a positive impact on
overall system performance.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix, the spelling of "failded" is incorrect in dev_err and
dev_warn messages. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the icplus driver has been fixed all PHY drivers supporting
interrupts have both callbacks (config_intr and ack_interrupt)
implemented - as it should be. Therefore phy_drv_supports_irq()
can be changed now to check for both callbacks being implemented.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-11-14
This series contains updates to i40e and virtchnl.
Lance Roy updates i40e to use lockdep_assert_held() instead of
spin_is_locked(), since it is better suited to check locking
requirements.
Jan improves the code readability in XDP by adding the use of a local
variable. Provides protection on methods that create/modify/destroy
VF's via locking mechanism to prevent unstable behaviour and potential
kernel panics.
Krzysztof adds a hardware capability flag to indicate whether firmware
supports stopping the LLDP agent.
Patryk replaces the use of strncpy() with strlcpy() to ensure the buffer
is NULL terminated.
Mitch fixes the issue of trying to start nway on devices that do not
support auto-negotiation, by checking the autoneg state before
attempting to restart nway.
Alice updates virtchnl to keep the checks all together for ease of
readability and consistency. Also fixed a "off by one" error in the
number of traffic classes being calculated.
Richard fixed VF port VLANs, where the priority bits were incorrectly
set because the incorrect shift and mask bits were being used.
Alan adds a bit to set and check if a timeout recovery is already
pending to prevent overlapping transmit timeout recovery.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow ERP sharing for multiple mask. Do it by properly implementing
delta_create() objagg object. Use the computed delta info for inserting
rules in A-TCAM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
separate helpers
Later on the same code is going to be needed for deltas as well. So push
the procedures related to increment and decrement of num_ctcam_erps
into a separate helpers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
key/mask check
Since two remaining users of mlxsw_afk_encode() do not specify
block ranges to work on, remove the args. Also, key/mask is always
non-NULL now, so skip the checks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlxsw_sp_acl_atcam_12kb_lkey_id_get()
No need to do key encoding again in
mlxsw_sp_acl_atcam_12kb_lkey_id_get(). Instead of that, introduce
a new helper that would just clear unused blocks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change order so it is aligned with the usual case where the "write_to"
buffer comes as the first arg.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device requires that the master mask of each region will be
composed from a logical OR between all the unmasked bits in the region.
Currently, this is just a logical OR between all the eRPs used in the
region, but the next patch is going to introduce delta bits support
which need to be taken into account as well.
Since the eRP does not include the delta bits, pass the key pointer to
mlxsw_sp_acl_erp_master_mask_set/clear instead. Convert key->mask to
the bitmap on fly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the ERPs are tracked internally in a hashtable. Benefit from
the newly introduced objagg library and use it to track ERPs. At this
point, there is no nesting of objects done, as the delta_create callback
always returns -EOPNOTSUPP. On the way, add "mask" into ERP mask get and
set functions and struct names.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already have a workaround for a couple of switches whose internal
PHYs only have the Marvel OUI, but no model number. We detect such
PHYs and give them the 6390 ID as the model number. However the
mv88e6161 has two SERDES interfaces in the same address range as its
internal PHYs. These suffer from the same problem, the Marvell OUI,
but no model number. As a result, these SERDES interfaces were getting
the same PHY ID as the mv88e6390, even though they are not PHYs, and
the Marvell PHY driver was trying to drive them.
Add a special case to stop this from happen.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-11-13
This series contains updates to the ice driver only.
Brett cleans up debug print messages by removing useless or duplicate
messages, and make sure we assign the hardware head pointer to head
instead of the software head pointer. Resolved an issue when disabling
SRIOV we were trying to stop queues multiple times, so make sure we
disable SRIOV before stopping transmit and receive queues for VF.
Tony fixes a potential NULL pointer dereference during a VF reset.
Anirudh resolves an issue where we were releasing the VSI before
removing the VSI scheduler node, which was resulting in an error "Failed
to set LAN Tx queue context, error: -1". Also fixed the guaranteed
number of VSIs available and used by discovering the device
capabilities to determine the 'guar_num_vsi' per function, rather than
always using the theoretical max number of VSIs every time.
Dave avoids a deadlock by nesting RTNL locking, so added a boolean to
determine if the RTNL lock is already held.
Lev fixes bad mask values which would break compilation.
Piotr increases the receive queue disable timeout since it can take
additional time to finish all pending queue requests.
Usha resolves an issue of VLAN priority tagged traffic not appearing on
all traffic classes, which was causing ETS bandwidth shaping to not work
as expected.
Henry fixes the reset path to cleanup the old scheduler tree before
rebuilding it.
Md Fahad removes a unnecessary check which was causing a driver load
error on platforms with more than 128 cores.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When HW GRO enable, protocol stack will not do GRO again,
driver should add gro param to the skb for the protocol
stack..
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MAX_SKB_FRAGS in protocol stack is defined as:
MAX_SKB_FRAGS is 17 when PAGE_SIZE is 4K. If HW enable GRO, it may
merge small packets and the rx buffer may be more than
MAX_SKB_FRAGS. So driver will add skb chain when RX buffer num.
more than MAX_SKB_FRAGS.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support of ethtool -K to enable/disable
hardware GRO in HNS3 PF/VF driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "FE bit" in the description means the last description for
a packets. When HW GRO enable, HW write data to ring every
packet/buffer, there is greater probability that driver handle
with the describtion but HW still not set the "FE bit".
When drier handle the packet and HW still not set "FE bit",
driver stores skb and bd_num in rx ring, and continue to use the
skb and bd_num in next napi.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HNS3 hardware Revision B(=0x21) supports Hardware GRO feature. This
patch enables this feature in the HNS3 PF/VF driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move IRQ configuration for IP101A/G from config_init to config_intr
callback. Reasons:
1. This allows phylib to disable interrupts if needed.
2. Icplus was the only driver supporting interrupts w/o defining a
config_intr callback. Now we can add a phylib plausibility check
disabling interrupt mode if one of the two irq-related callbacks
isn't defined.
I don't own hardware with this PHY, and the change is based on the
datasheet for IP101A LF (which is supposed to be register-compatible
with IP101A/G). Change is compile-tested only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a TX hang occurs, we attempt to recover by incrementally resetting.
If we're starved for CPU time, it's possible the reset doesn't actually
complete (or even fire) before another tx_timeout fires causing us to
fly through the different resets without actually doing them.
This adds a bit to set and check if a timeout recovery is already
pending and, if so, bail out of tx_timeout. The bit will get cleared at
the end of i40e_rebuild when reset is complete.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The i40e driver complains about unprivileged VFs trying to configure
promiscuous mode each time a VF reset occurs. This isn't the fault of
the poor VF driver - the PF driver itself is making the request.
To fix this, skip the privilege check if the request is to disable all
promiscuous activity. This gets rid of the bogus message, but doesn't
affect privilege checks, since we really only care if the unprivileged
VF is trying to enable promiscuous mode.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When using port VLAN, for VFs, and setting priority bits, the device
was sending out incorrect priority bits, and also setting the CFI
bit incorrectly.
To fix this, changed shift and mask bit definition for this function, to
use the correct ones.
Signed-off-by: Richard Rodriguez <richard.rodriguez@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In i40e_get_settings_link_up, set ks->base.speed to SPEED_UNKNOWN
in the case where we don't know the link speed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On link types that do not support autoneg, we cannot attempt to restart
nway negotiation. This results in a dead link that requires a power
cycle to remedy.
Fix this by saving off the autoneg state and checking this value before
we try to restart nway.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch allows disabling FW LLDP agent on X722 devices.
It also changes a source of information for this feature from
pf->hw_features to pf->hw.flags which are set in i40e_init_adminq.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The version numbers have not been kept up to date and this is
an effort to ammend that.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A scenario has been found in which simultaneous
addition/removal and modification of VF's might cause
unstable behaviour, up to and including kernel panics.
Protect the methods that create/modify/destroy VF's
by locking them behind an atomically set bit in PF status
bitfield.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Using strncpy allows destination buffer to be not null terminated
after the copying takes place. strlcpy ensures that's not the
case by explicitly setting last element in the buffer as '\0'.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add HW capability flag to indicate that firmware supports stopping
LLDP agent. This feature has been added in FW API 1.7 for XL710
devices and 1.6 for X722. Also raise expected minor version number
for X722 FW API to 6.
Signed-off-by: Krzysztof Galazka <krzysztof.galazka@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use a local variable to make the code a bit more readable.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
lockdep_assert_held() is better suited to checking locking requirements,
since it won't get confused when someone else holds the lock. This is
also a step towards possibly removing spin_is_locked().
Signed-off-by: Lance Roy <ldr709@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In preparation of handling more Qdisc types switch to a different
offload strategy. We have now recreated the Qdisc hierarchy in
the driver. Every time the hierarchy changes parse it, and update
the configuration of the HW accordingly.
While at it drop the support of pretending that we can instantiate
a single queue on a multi-queue device in HW/FW. MQ is now required,
and each queue will have its own instance of RED.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new driver Qdisc structure to keep track of parameters
of RED Qdiscs. This way as the Qdisc moves around in the hierarchy
we will be able to configure the HW appropriately.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RED qdisc will replace its child Qdisc with a new FIFO queue if
it is reconfigured and the limit parameter is not 0.
This means that when it's created with limit of 0 it will have no FIFO,
and all packets will be dropped. If it's changed and limit is specified
it will loose its existing child (implicit graft). Make sure we mark
RED Qdisc child as NFP_QDISC_UNTRACKED if its not the expected FIFO.
nfp_abm_qdisc_replace() will return 1 if Qdisc already existed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using graft notifications recreate in the driver the full Qdisc
hierarchy. Keep track of how many times each Qdisc is attached
to the hierarchy to make sure we don't offload Qdiscs which are
attached multiple times (device queues can't be shared). For
graft events of Qdiscs we don't know exist make the child as
invalid/untracked.
Note that MQ Qdisc doesn't send destruction events reliably when
device is dismantled, so we need to manually clean out the
children otherwise we'd think Qdiscs which are still in use
are getting freed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To keep track of Qdisc hierarchy allocate a table for children
for each Qdisc. RED Qdisc can only have one child.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Keep track of which Qdisc is currently root. We need to implement
TC_SETUP_ROOT_QDISC handling, and for completeness also clear the
root Qdisc pointer when it's freed. TC_SETUP_ROOT_QDISC isn't always
sent when device is dismantled.
Remembering the root Qdisc will allow us to build the entire hierarchy
in following patches.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocate an object corresponding to any offloaded qdisc we are
informed about by the kernel. Not only the qdiscs we have a
chance of offloading.
The count of created objects will be used to decide whether
the ethtool TC offload can be disabled, since otherwise we may
miss destroy commands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of writing the threshold out when Qdisc is configured
and not remembering it move to a scheme where we remember all
thresholds. When configuration changes parse the offloaded
Qdiscs and set thresholds appropriately.
This will help future extensions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|