| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has one revert because of a regression, two fixes for tiny race
windows (which we were not able to trigger), a MAINTAINERS addition,
and a SPDX fix"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: stm32: Use the correct style for SPDX License Identifier
i2c: emev2: avoid race when unregistering slave client
i2c: rcar: avoid race when unregistering slave client
MAINTAINERS: i2c-imx: take over maintainership
Revert "i2c: imx: improve the error handling in i2c_imx_dma_request()"
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.3-rc5
Here are some new modem device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.3-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add the BroadMobi BM818 card
USB: serial: option: Add Motorola modem UARTs
USB: serial: option: add D-Link DWM-222 device ID
USB: serial: option: Add support for ZTE MF871A
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These add a check to avoid recent suspend-to-idle power regression on
systems with NVMe drives where the PCIe ASPM policy is "performance"
(or when the kernel is built without ASPM support), fix an issue
related to frequency limits in the schedutil cpufreq governor and fix
a mistake related to the PM QoS usage in the cpufreq core introduced
recently.
Specifics:
- Disable NVMe power optimization related to suspend-to-idle added
recently on systems where PCIe ASPM is not able to put PCIe links
into low-power states to prevent excess power from being drawn by
the system while suspended (Rafael Wysocki).
- Make the schedutil governor handle frequency limits changes
properly in all cases (Viresh Kumar).
- Prevent the cpufreq core from treating positive values returned by
dev_pm_qos_update_request() as errors (Viresh Kumar)"
* tag 'pm-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
nvme-pci: Allow PCI bus-level PM to be used if ASPM is disabled
PCI/ASPM: Add pcie_aspm_enabled()
cpufreq: schedutil: Don't skip freq update when limits change
cpufreq: dev_pm_qos_update_request() can return 1 on success
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Fixes in dmaengine drivers for:
- dw-edma: endianess, _iomem type and stack usages
- ste_dma40: unneeded variable and null-pointer dereference
- tegra210-adma: unused function
- omap-dma: off-by-one fix"
* tag 'dmaengine-fix-5.3-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
omap-dma/omap_vout_vrfb: fix off-by-one fi value
dmaengine: stm32-mdma: Fix a possible null-pointer dereference in stm32_mdma_irq_handler()
dmaengine: tegra210-adma: Fix unused function warnings
dmaengine: ste_dma40: fix unneeded variable warning
dmaengine: dw-edma: fix endianess confusion
dmaengine: dw-edma: fix __iomem type confusion
dmaengine: dw-edma: fix unnecessary stack usage
|
|
Pull drm fixes from Dave Airlie:
"Nothing too crazy this week, one amdgpu fix to use vmalloc for a
struct that grew in size, and another MST fix for nouveau, and some
other misc fixes:
i915:
- single GVT use after free fix
scheduler:
- entity destruction race fix
amdgpu:
- struct allocation fix
- gfx9 soft recovery fix
nouveau:
- followup MST fix
ast:
- vga register race fix"
* tag 'drm-fixes-2019-08-16' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau: Only recalculate PBN/VCPI on mode/connector changes
drm/ast: Fixed reboot test may cause system hanged
drm/scheduler: use job count instead of peek
drm/amd/display: use kvmalloc for dc_state (v2)
drm/amdgpu: fix gfx9 soft recovery
drm/i915: Use after free in error path in intel_vgpu_create_workload()
|
|
* pm-cpufreq:
cpufreq: schedutil: Don't skip freq update when limits change
cpufreq: dev_pm_qos_update_request() can return 1 on success
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-linus
Vinod writes:
soundwire fixes for v5.3-rc5
Pierre sent fixes which are queued now for v5.3-rc5 are:
- regmap dependecy
- cadence register definitions
* tag 'soundwire-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: fix regmap dependencies and align with other serial links
soundwire: cadence_master: fix definitions for INTSTAT0/1
soundwire: cadence_master: fix register definition for SLAVE_STATE
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.4-rc5:
- GVT use-after-free fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87zhkag9ic.fsf@intel.com
|
|
Pull auxdisplay fixes from Miguel Ojeda:
"A few minor auxdisplay improvements:
- A couple of small header cleanups for charlcd (Masahiro Yamada)
- A trivial typo fix for the examples of cfag12864b (Masahiro Yamada)
- An Kconfig help text improvement for charlcd (Mans Rullgard)
- An error path fix for panel (zhengbin)"
* tag 'auxdisplay-for-linus-v5.3-rc5' of git://github.com/ojeda/linux:
auxdisplay: Fix a typo in cfag12864b-example.c
auxdisplay: charlcd: add include guard to charlcd.h
auxdisplay: charlcd: move charlcd.h to drivers/auxdisplay
auxdisplay: charlcd: add help text for backlight initial state
auxdisplay: panel: need to delete scan_timer when misc_register fails in panel_attach
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix building DT binding examples for in tree builds
- Correct some refcounting in adjust_local_phandle_references()
- Update FSL FEC binding with deprecated properties
- Schema fix in stm32 pinctrl
- Fix typo in of_irq_parse_one docbook comment
* tag 'devicetree-fixes-for-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: irq: fix a trivial typo in a doc comment
dt-bindings: pinctrl: stm32: Fix 'st,syscfg' schema
dt-bindings: fec: explicitly mark deprecated properties
of: resolver: Add of_node_put() before return and break
dt-bindings: Fix generated example files getting added to schemas
|
|
lib/devres.c, which implements devm_ioremap_resource(), is only built
when CONFIG_HAS_IOMEM is set/enabled, so XILINX_SDFEC should depend
on HAS_IOMEM. Fixes this build error (as seen on UML builds):
ERROR: "devm_ioremap_resource" [drivers/misc/xilinx_sdfec.ko] undefined!
Fixes: 76d83e1c3233 ("misc: xilinx-sdfec: add core driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Derek Kiernan <derek.kiernan@xilinx.com>
Cc: Dragan Cvetic <dragan.cvetic@xilinx.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/f9004be5-9925-327b-3ec2-6506e46fe565@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB buffer allocation code is the only place in the usb core (and in
fact the whole kernel) that uses is_device_dma_capable, while the URB
mapping code uses the uses_dma flag in struct usb_bus. Switch the buffer
allocation to use the uses_dma flag used by the rest of the USB code,
and create a helper in hcd.h that checks this flag as well as the
CONFIG_HAS_DMA to simplify the caller a bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190811080520.21712-3-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the HCD provides a localmem pool we will never use the DMA pools, so
don't create them.
Fixes: b0310c2f09bb ("USB: use genalloc for USB HCs with local memory")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190811080520.21712-2-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If driver probe needs to be deferred, e.g. because ci_hdrc_add_device()
isn't ready yet, this driver currently misbehaves badly:
a) success is still reported to the driver core (meaning a 2nd
probe attempt will never be done), leaving the driver in
a dysfunctional state and the hardware unusable
b) driver remove / shutdown OOPSes:
[ 206.786916] Unable to handle kernel paging request at virtual address fffffdff
[ 206.794148] pgd = 880b9f82
[ 206.796890] [fffffdff] *pgd=abf5e861, *pte=00000000, *ppte=00000000
[ 206.803179] Internal error: Oops: 37 [#1] PREEMPT SMP ARM
[ 206.808581] Modules linked in: wl18xx evbug
[ 206.813308] CPU: 1 PID: 1 Comm: systemd-shutdow Not tainted 4.19.35+gf345c93b4195 #1
[ 206.821053] Hardware name: Freescale i.MX7 Dual (Device Tree)
[ 206.826813] PC is at ci_hdrc_remove_device+0x4/0x20
[ 206.831699] LR is at ci_hdrc_imx_remove+0x20/0xe8
[ 206.836407] pc : [<805cd4b0>] lr : [<805d62cc>] psr: 20000013
[ 206.842678] sp : a806be40 ip : 00000001 fp : 80adbd3c
[ 206.847906] r10: 80b1b794 r9 : 80d5dfe0 r8 : a8192c44
[ 206.853136] r7 : 80db93a0 r6 : a8192c10 r5 : a8192c00 r4 : a93a4a00
[ 206.859668] r3 : 00000000 r2 : a8192ce4 r1 : ffffffff r0 : fffffdfb
[ 206.866201] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 206.873341] Control: 10c5387d Table: a9e0c06a DAC: 00000051
[ 206.879092] Process systemd-shutdow (pid: 1, stack limit = 0xb271353c)
[ 206.885624] Stack: (0xa806be40 to 0xa806c000)
[ 206.889992] be40: a93a4a00 805d62cc a8192c1c a8170e10 a8192c10 8049a490 80d04d08 00000000
[ 206.898179] be60: 00000000 80d0da2c fee1dead 00000000 a806a000 00000058 00000000 80148b08
[ 206.906366] be80: 01234567 80148d8c a9858600 00000000 00000000 00000000 00000000 80d04d08
[ 206.914553] bea0: 00000000 00000000 a82741e0 a9858600 00000024 00000002 a9858608 00000005
[ 206.922740] bec0: 0000001e 8022c058 00000000 00000000 a806bf14 a9858600 00000000 a806befc
[ 206.930927] bee0: a806bf78 00000000 7ee12c30 8022c18c a806bef8 a806befc 00000000 00000001
[ 206.939115] bf00: 00000000 00000024 a806bf14 00000005 7ee13b34 7ee12c68 00000004 7ee13f20
[ 206.947302] bf20: 00000010 7ee12c7c 00000005 7ee12d04 0000000a 76e7dc00 00000001 80d0f140
[ 206.955490] bf40: ab637880 a974de40 60000013 80d0f140 ab6378a0 80d04d08 a8080470 a9858600
[ 206.963677] bf60: a9858600 00000000 00000000 8022c24c 00000000 80144310 00000000 00000000
[ 206.971864] bf80: 80101204 80d04d08 00000000 80d04d08 00000000 00000000 00000003 00000058
[ 206.980051] bfa0: 80101204 80101000 00000000 00000000 fee1dead 28121969 01234567 00000000
[ 206.988237] bfc0: 00000000 00000000 00000003 00000058 00000000 00000000 00000000 00000000
[ 206.996425] bfe0: 0049ffb0 7ee13d58 0048a84b 76f245a6 60000030 fee1dead 00000000 00000000
[ 207.004622] [<805cd4b0>] (ci_hdrc_remove_device) from [<805d62cc>] (ci_hdrc_imx_remove+0x20/0xe8)
[ 207.013509] [<805d62cc>] (ci_hdrc_imx_remove) from [<8049a490>] (device_shutdown+0x16c/0x218)
[ 207.022050] [<8049a490>] (device_shutdown) from [<80148b08>] (kernel_restart+0xc/0x50)
[ 207.029980] [<80148b08>] (kernel_restart) from [<80148d8c>] (sys_reboot+0xf4/0x1f0)
[ 207.037648] [<80148d8c>] (sys_reboot) from [<80101000>] (ret_fast_syscall+0x0/0x54)
[ 207.045308] Exception stack(0xa806bfa8 to 0xa806bff0)
[ 207.050368] bfa0: 00000000 00000000 fee1dead 28121969 01234567 00000000
[ 207.058554] bfc0: 00000000 00000000 00000003 00000058 00000000 00000000 00000000 00000000
[ 207.066737] bfe0: 0049ffb0 7ee13d58 0048a84b 76f245a6
[ 207.071799] Code: ebffffa8 e3a00000 e8bd8010 e92d4010 (e5904004)
[ 207.078021] ---[ end trace be47424e3fd46e9f ]---
[ 207.082647] Kernel panic - not syncing: Fatal exception
[ 207.087894] ---[ end Kernel panic - not syncing: Fatal exception ]---
c) the error path in combination with driver removal causes
imbalanced calls to the clk_*() and pm_()* APIs
a) happens because the original intended return value is
overwritten (with 0) by the return code of
regulator_disable() in ci_hdrc_imx_probe()'s error path
b) happens because ci_pdev is -EPROBE_DEFER, which causes
ci_hdrc_remove_device() to OOPS
Fix a) by being more careful in ci_hdrc_imx_probe()'s error
path and not overwriting the real error code
Fix b) by calling the respective cleanup functions during
remove only when needed (when ci_pdev != NULL, i.e. when
everything was initialised correctly). This also has the
side effect of not causing imbalanced clk_*() and pm_*()
API calls as part of the error code path.
Fixes: 7c8e8909417e ("usb: chipidea: imx: add HSIC support")
Signed-off-by: André Draszik <git@andred.net>
Cc: stable <stable@vger.kernel.org>
CC: Peter Chen <Peter.Chen@nxp.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Pengutronix Kernel Team <kernel@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: NXP Linux Team <linux-imx@nxp.com>
CC: linux-usb@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190810150758.17694-1-git@andred.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On the Gemini SoC the FOTG2 stalls after port reset
so restart the HCD after each port reset.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190810150458.817-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A few checks checked for the size of the pointer to a structure
instead of the structure itself. Copy & paste issue presumably.
Fixes: e4c6fb7794982 ("usbnet: move the CDC parser into USB core")
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+45a53506b65321c1fe91@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20190813093541.18889-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
destroy() will decrement the refcount on the interface, so that
it needs to be taken so early that it never undercounts.
Fixes: 7fb57a019f94e ("USB: cdc-acm: Fix potential deadlock (lockdep warning)")
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+1b2449b7b5dc240d107a@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20190808142119.7998-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is some "confusing" license text in some of the sm750fb driver
files. After discussing it with the company, it turns out to have been
a mistake and these lines can be safely removed. The files are all to
be licensed under the GPLv2 license.
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: linux-fbdev@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190815123009.16499-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As Chao pointed out [1], ENOTSUPP is used for NFS
protocol only, we should use EOPNOTSUPP instead...
[1] https://lore.kernel.org/lkml/108ee2f9-75dd-b8ab-8da7-b81c17bafbf6@huawei.com/
Reported-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Link: https://lore.kernel.org/r/20190814103705.60698-3-gaoxiang25@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For some specific fields, use EOPNOTSUPP instead of EIO
for values which look sane but aren't supported right now.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Link: https://lore.kernel.org/r/20190814103705.60698-2-gaoxiang25@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Previously, EROFS uses EIO to indicate that filesystem
is corrupted as well. However, as Pavel said [1], other
filesystems tend to use EUCLEAN(EFSCORRUPTED) instead,
let's follow what others do right now.
Also, add some more prints to the syslog.
[1] https://lore.kernel.org/lkml/20190813114821.GB11559@amd/
Suggested-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Link: https://lore.kernel.org/r/20190814103705.60698-1-gaoxiang25@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Variable fx2delay is being initialized with a value that is never read
and fx2delay is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190815105314.5756-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a statement that is indented one level too deeply, remove
the extraneous tab.
Addresses-Coverity: ("Identation does not match nesting level")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190815084034.13885-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Static structure apex_desc, of type gasket_driver_desc, is used only as
an argument to the functions gasket_register_device() and
gasket_unregister_device(). In the definitions of both these functions,
their parameter is declared as const. Hence make apex_desc itself
constant to protect it from modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190815054924.643-1-nishkadg.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
in fill_inode() we call iloc() twice.Avoiding the extra call by
storing the result.
Signed-off-by: Pratik Shinde <pratikshinde320@gmail.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Cc: Gao Xiang <gaoxiang25@huawei.com>
Link: https://lore.kernel.org/r/20190813203840.13782-1-pratikshinde320@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a VID:PID for the BroadMobi BM818 M.2 card
T: Bus=01 Lev=03 Prnt=40 Port=03 Cnt=01 Dev#= 44 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2020 ProdID=2060 Rev=00.00
S: Manufacturer=Qualcomm, Incorporated
S: Product=Qualcomm CDMA Technologies MSM
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
Signed-off-by: Bob Ham <bob.ham@puri.sm>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: stable <stable@vger.kernel.org>
[ johan: use USB_DEVICE_INTERFACE_CLASS() ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
On Motorola Mapphone devices such as Droid 4 there are five USB ports
that do not use the same layout as Gobi 1K/2K/etc devices listed in
qcserial.c. So we should use qcaux.c or option.c as noted by
Dan Williams <dan.j.williams@intel.com>.
As the Motorola USB serial ports have an interrupt endpoint as shown
with lsusb -v, we should use option.c instead of qcaux.c as pointed out
by Johan Hovold <johan@kernel.org>.
The ff/ff/ff interfaces seem to always be UARTs on Motorola devices.
For the other interfaces, class 0x0a (CDC Data) should not in general
be added as they are typically part of a multi-interface function as
noted earlier by Bjørn Mork <bjorn@mork.no>.
However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a
class is only used for flashing the modem firmware, and there are no
other interfaces. So I've added that too with more details below as it
works just fine.
The ttyUSB ports on Droid 4 are:
ttyUSB0 DIAG, CQDM-capable
ttyUSB1 MUX or NMEA, no response
ttyUSB2 MUX or NMEA, no response
ttyUSB3 TCMD
ttyUSB4 AT-capable
The ttyUSB0 is detected as QCDM capable by ModemManager. I think
it's only used for debugging with ModemManager --debug for sending
custom AT commands though. ModemManager already can manage data
connection using the USB QMI ports that are already handled by the
qmi_wwan.c driver.
To enable the MUX or NMEA ports, it seems that something needs to be
done additionally to enable them, maybe via the DIAG or TCMD port.
It might be just a NVRAM setting somewhere, but I have no idea what
NVRAM settings may need changing for that.
The TCMD port seems to be a Motorola custom protocol for testing
the modem and to configure it's NVRAM and seems to work just fine
based on a quick test with a minimal tcmdrw tool I wrote.
The voice modem AT-capable port seems to provide only partial
support, and no PM support compared to the TS 27.010 based UART
wired directly to the modem.
The UARTs added with this change are the same product IDs as the
Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't
have any mdm9600 based devices, so I have only tested these on
mdm6600 based droid 4.
Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android
Linux kernel driver moto_flashqsc.c just seems to change the
port->bulk_out_size to 8K from the default. And is only used for
flashing the modem firmware it seems.
I've verified that flashing the modem with signed firmware works just
fine with the option driver after manually toggling the GPIO pins, so
I've added droid 4 modem flashing mode to the option driver. I've not
added the other devices listed in moto_flashqsc.c in case they really
need different port->bulk_out_size. Those can be added as they get
tested to work for flashing the modem.
After this patch the output of /sys/kernel/debug/usb/devices has
the following for normal 22b8:2a70 mode including the related qmi_wwan
interfaces:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=2a70 Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=8b(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8c(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=08(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
In 22b8:900e "qc_dload" mode the device shows up as:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=900e Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
And in 22b8:4281 "ram_downloader" mode the device shows up as:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=4281 Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Lars Melin <larsm17@gmail.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
drm-fixes-5.3-2019-08-14:
amdgpu:
- Use kvalloc for dc_state to avoid allocation
failures in some cases.
- Fix gfx9 soft recovery
scheduler:
- Fix a race condition when destroying entities
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190815024919.3434-1-alexander.deucher@amd.com
|
|
I -thought- I had fixed this entirely, but it looks like that I didn't
test this thoroughly enough as we apparently still make one big mistake
with nv50_msto_atomic_check() - we don't handle the following scenario:
* CRTC #1 has n VCPI allocated to it, is attached to connector DP-4
which is attached to encoder #1. enabled=y active=n
* CRTC #1 is changed from DP-4 to DP-5, causing:
* DP-4 crtc=#1→NULL (VCPI n→0)
* DP-5 crtc=NULL→#1
* CRTC #1 steals encoder #1 back from DP-4 and gives it to DP-5
* CRTC #1 maintains the same mode as before, just with a different
connector
* mode_changed=n connectors_changed=y
(we _SHOULD_ do VCPI 0→n here, but don't)
Once the above scenario is repeated once, we'll attempt freeing VCPI
from the connector that we didn't allocate due to the connectors
changing, but the mode staying the same. Sigh.
Since nv50_msto_atomic_check() has broken a few times now, let's rethink
things a bit to be more careful: limit both VCPI/PBN allocations to
mode_changed || connectors_changed, since neither VCPI or PBN should
ever need to change outside of routing and mode changes.
Changes since v1:
* Fix accidental reversal of clock and bpp arguments in
drm_dp_calc_pbn_mode() - William Lewis
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reported-by: Bohdan Milar <bmilar@redhat.com>
Tested-by: Bohdan Milar <bmilar@redhat.com>
Fixes: 232c9eec417a ("drm/nouveau: Use atomic VCPI helpers for MST")
References: 412e85b60531 ("drm/nouveau: Only release VCPI slots on mode changes")
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@redhat.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Juston Li <juston.li@intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Karol Herbst <karolherbst@gmail.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: <stable@vger.kernel.org> # v5.1+
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190809005307.18391-1-lyude@redhat.com
|
|
There is another thread still access standard VGA I/O while loading drm driver.
Disable standard VGA I/O decode to avoid this issue.
Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523410059-18415-1-git-send-email-yc_chen@aspeedtech.com
|
|
Diverged from what the code does with commit 530210c7814e ("of/irq: Replace
of_irq with of_phandle_args").
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The spsc_queue_peek function is accessing queue->head which belongs to
the consumer thread and shouldn't be accessed by the producer
This is fixing a rare race condition when destroying entities.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Monk.liu@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Pull rdma fixes from Doug Ledford:
"Fairly small pull request for -rc3. I'm out of town the rest of this
week, so I made sure to clean out as much as possible from patchworks
in enough time for 0-day to chew through it (Yay! for 0-day being back
online! :-)). Jason might send through any emergency stuff that could
pop up, otherwise I'm back next week.
The only real thing of note is the siw ABI change. Since we just
merged siw *this* release, there are no prior kernel releases to
maintain kernel ABI with. I told Bernard that if there is anything
else about the siw ABI he thinks he might want to change before it
goes set in stone, he should get it in ASAP. The siw module was around
for several years outside the kernel tree, and it had to be revamped
considerably for inclusion upstream, so we are making no attempts to
be backward compatible with the out of tree version. Once 5.3 is
actually released, we will have our baseline ABI to maintain.
Summary:
- Fix a memory registration release flow issue that was causing a
WARN_ON (mlx5)
- If the counters for a port aren't allocated, then we can't do
operations on the non-existent counters (core)
- Check the right variable for error code result (mlx5)
- Fix a use after free issue (mlx5)
- Fix an off by one memory leak (siw)
- Actually return an error code on error (core)
- Allow siw to be built on 32bit arches (siw, ABI change, but OK
since siw was just merged this merge window and there is no prior
released kernel to maintain compatibility with and we also updated
the rdma-core user space package to match)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/siw: Change CQ flags from 64->32 bits
RDMA/core: Fix error code in stat_get_doit_qp()
RDMA/siw: Fix a memory leak in siw_init_cpulist()
IB/mlx5: Fix use-after-free error while accessing ev_file pointer
IB/mlx5: Check the correct variable in error handling code
RDMA/counter: Prevent QP counter binding if counters unsupported
IB/mlx5: Fix implicit MR release flow
|
|
Pull dma-mapping fixes from Christoph Hellwig:
- fix the handling of the bus_dma_mask in dma_get_required_mask, which
caused a regression in this merge window (Lucas Stach)
- fix a regression in the handling of DMA_ATTR_NO_KERNEL_MAPPING (me)
- fix dma_mmap_coherent to not cause page attribute mismatches on
coherent architectures like x86 (me)
* tag 'dma-mapping-5.3-4' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: fix page attributes for dma_mmap_*
dma-direct: don't truncate dma_required_mask to bus addressing capabilities
dma-direct: fix DMA_ATTR_NO_KERNEL_MAPPING
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- A couple more fixes for the Intel VT-d driver for bugs introduced
during the recent conversion of this driver to use IOMMU core default
domains.
- Fix for common dma-iommu code to make sure MSI mappings happen in the
correct domain for a device.
- Fix a corner case in the handling of sg-lists in dma-iommu code that
might cause dma_length to be truncated.
- Mark a switch as fall-through in arm-smmu code.
* tag 'iommu-fixes-v5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix possible use-after-free of private domain
iommu/vt-d: Detach domain before using a private one
iommu/dma: Handle SG length overflow better
iommu/vt-d: Correctly check format of page table in debugfs
iommu/vt-d: Detach domain when move device out of group
iommu/arm-smmu: Mark expected switch fall-through
iommu/dma: Handle MSI mappings separately
|
|
Link settings can be changed only when the interface is down. Disable
and re-enable the interface, if necessary, behind the scenes so that we do
not force users to an if down/up sequence.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-11-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The register_netdev() call should be made only when ready to process any
user request on the interface. Move the call to be the last one issued
in the probe sequence.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-10-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the current state, the dpaa2-ethsw driver supports only one bridge
per DPSW object. Reword the error message so that this information is
much more clear.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-9-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ethsw_add_vlan() function is already called only when the VLAN is
not yet configured on the switch. Remove the redundant check.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-8-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ethtool core already zeroes the memory before calling
.get_ethtool_stats() thus making the memset unnecessary. Remove it.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-7-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use a bool instead of an u8 in ethsw_set_learning() and
ethsw_port_set_flood() to encode an binary type property.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-6-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since ethtool will be loud enough if the .set_link_ksettings() callback
fails, remove the debug messages which do not add additional
information.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-5-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the '\n' line terminator to the string formats missing it.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-4-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
At probe time, only the DPSW object should be enabled without the
associated ports, which will get enabled on dev_open. Remove the
ethsw_open() and ethsw_stop() functions and replace them only with
dpsw_enable()/_disable().
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-3-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Do not add an IGMP multicast address by default since we do not support
Rx/Tx ar the moment.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1565700187-16048-2-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch corrects the SPDX License Identifier style
in header file related to STM32 Driver for I2C hardware
bus support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
After we disabled interrupts, there might still be an active one
running. Sync before clearing the pointer to the slave device.
Fixes: c31d0a00021d ("i2c: emev2: add slave support")
Reported-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
After we disabled interrupts, there might still be an active one
running. Sync before clearing the pointer to the slave device.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Reported-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Variable ret is initialized to a value that is never read and it is
re-assigned later. The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190813124838.1317-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the checkpatch.pl script was run, it showed lines with length
more than 80 characters in rtl8712_recv.c file. Fixed by
breaking it up into two lines within 80 characters.
Signed-off-by: Merwin Trever Ferrao <merwintf@gmail.com>
Link: https://lore.kernel.org/r/20190813065806.GA23606@IoT-COE
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
