| Age | Commit message (Collapse) | Author |
|---|
|
I was unable to get clk_set_rate() setting a lower RPC-IF clock frequency
and that issue boiled down to me not passing CLK_SET_RATE_PARENT flag to
clk_register_composite() when registering the RPC[D2] clocks...
Fixes: db4a0073cc82 ("clk: renesas: rcar-gen3: Add RPC clocks")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/be27a344-d8bf-9e0c-8950-2d1b48498496@cogentembedded.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
CONFIG_ARCH_R8A7796 was renamed to CONFIG_ARCH_R8A77960 in commit
39e57e14d7eaf818 ("soc: renesas: Add ARCH_R8A77960 for existing R-Car
M3-W"), so its users can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191211100220.6854-1-geert+renesas@glider.be
|
|
All multipliers and dividers are small.
Storing them in u8 instead of unsigned int reduces kernel size for a
generic kernel by ca. 0.5 KiB.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20191206133254.23800-1-geert+renesas@glider.be
|
|
Pull networking fixes from David Miller:
1) More jumbo frame fixes in r8169, from Heiner Kallweit.
2) Fix bpf build in minimal configuration, from Alexei Starovoitov.
3) Use after free in slcan driver, from Jouni Hogander.
4) Flower classifier port ranges don't work properly in the HW offload
case, from Yoshiki Komachi.
5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.
6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.
7) Fix flow dissection in dsa TX path, from Alexander Lobakin.
8) Stale syncookie timestampe fixes from Guillaume Nault.
[ Did an evil merge to silence a warning introduced by this pull - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
r8169: fix rtl_hw_jumbo_disable for RTL8168evl
net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
r8169: add missing RX enabling for WoL on RTL8125
vhost/vsock: accept only packets with the right dst_cid
net: phy: dp83867: fix hfs boot in rgmii mode
net: ethernet: ti: cpsw: fix extra rx interrupt
inet: protect against too small mtu values.
gre: refetch erspan header from skb->data after pskb_may_pull()
pppoe: remove redundant BUG_ON() check in pppoe_pernet
tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
tcp: tighten acceptance of ACKs not matching a child socket
tcp: fix rejected syncookies due to stale timestamps
lpc_eth: kernel BUG on remove
tcp: md5: fix potential overestimation of TCP option space
net: sched: allow indirect blocks to bind to clsact in TC
net: core: rename indirect block ingress cb function
net-sysfs: Call dev_hold always in netdev_queue_add_kobject
net: dsa: fix flow dissection on Tx path
net/tls: Fix return values to avoid ENOTSUPP
net: avoid an indirect call in ____sys_recvmsg()
...
|
|
Pull more SCSI updates from James Bottomley:
"Eleven patches, all in drivers (no core changes) that are either minor
cleanups or small fixes.
They were late arriving, but still safe for -rc1"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
scsi: megaraid_sas: Make poll_aen_lock static
scsi: sd_zbc: Improve report zones error printout
scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
scsi: qla2xxx: unregister ports after GPN_FT failure
scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
scsi: pm80xx: Remove unused include of linux/version.h
scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
scsi: scsi_transport_sas: Fix memory leak when removing devices
scsi: lpfc: size cpu map by last cpu id set
scsi: ibmvscsi_tgt: Remove unneeded variable rc
|
|
Pull NTB update from Jon Mason:
"Just a simple patch to add a new Hygon Device ID to the AMD NTB device
driver"
* tag 'ntb-5.5' of git://github.com/jonmason/ntb:
NTB: Add Hygon Device ID
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
- fixups for Synaptics RMI4 driver
- a quirk for Goodinx touchscreen on Teclast tablet
- a new keycode definition for activating privacy screen feature found
on a few "enterprise" laptops
- updates to snvs_pwrkey driver
- polling uinput device for writing (which is always allowed) now works
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers
Input: synaptics-rmi4 - re-enable IRQs in f34v7_do_reflash
Input: goodix - add upside-down quirk for Teclast X89 tablet
Input: add privacy screen toggle keycode
Input: uinput - fix returning EPOLLOUT from uinput_poll
Input: snvs_pwrkey - remove gratuitous NULL initializers
Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q
|
|
Pull VFIO updates from Alex Williamson:
- Remove hugepage checks for reserved pfns (Ben Luo)
- Fix irq-bypass unregister ordering (Jiang Yi)
* tag 'vfio-v5.5-rc1' of git://github.com/awilliam/linux-vfio:
vfio/pci: call irq_bypass_unregister_producer() before freeing irq
vfio/type1: remove hugepage checks in is_invalid_reserved_pfn()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- a patch to fix a build warning
- a cleanup of no longer needed code in the Xen event handling
- a small series for the Xen grant driver avoiding high order
allocations and replacing an insane global limit by a per-call one
- a small series fixing Xen frontend/backend module referencing
* tag 'for-linus-5.5b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen-blkback: allow module to be cleanly unloaded
xen/xenbus: reference count registered modules
xen/gntdev: switch from kcalloc() to kvcalloc()
xen/gntdev: replace global limit of mapped pages by limit per call
xen/gntdev: remove redundant non-zero check on ret
xen/events: remove event handling recursion detection
|
|
In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().
v2: fix referenced commit id
Fixes: 14012c9f3bb9 ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiasen Lin <linjiasen@hygon.cn>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
RTL8125 also requires to enable RX for WoL.
v2: add missing Fixes tag
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we receive a new packet from the guest, we check if the
src_cid is correct, but we forgot to check the dst_cid.
The host should accept only packets where dst_cid is
equal to the host CID.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit ef87f7da6b28 ("net: phy: dp83867: move dt parsing to probe")
causes regression on TI dra71x-evm and dra72x-evm, where DP83867 PHY is
used in "rgmii-id" mode - the networking stops working.
Unfortunately, it's not enough to just move DT parsing code to .probe() as
it depends on phydev->interface value, which is set to correct value abter
the .probe() is completed and before calling .config_init(). So, RGMII
configuration can't be loaded from DT.
To fix and issue
- move RGMII validation code to .config_init()
- parse RGMII parameters in dp83867_of_init(), but consider them as
optional.
Fixes: ef87f7da6b28 ("net: phy: dp83867: move dt parsing to probe")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now RX interrupt is triggered twice every time, because in
cpsw_rx_interrupt() it is asked first and then disabled. So there will be
pending interrupt always, when RX interrupt is enabled again in NAPI
handler.
Fix it by first disabling IRQ and then do ask.
Fixes: 870915feabdc ("drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from cpsw itself")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Passing NULL to pppoe_pernet causes a crash via BUG_ON.
Dereferencing net in net_generici() also has the same effect. This patch
removes the redundant BUG_ON check on the same parameter.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-12-05
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.19:
('net/mlx5e: Query global pause state before setting prio2buffer')
For -stable v5.3
('net/mlx5e: Fix SFF 8472 eeprom length')
('net/mlx5e: Fix translation of link mode into speed')
('net/mlx5e: Fix freeing flow with kfree() and not kvfree()')
('net/mlx5e: ethtool, Fix analysis of speed setting')
('net/mlx5e: Fix TXQ indices to be sequential')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We may have found a bug in the nxp/lpc_eth.c driver. The function
platform_set_drvdata() is called twice, the second time it is called,
in lpc_mii_init(), it overwrites the struct net_device which should be
at pdev->dev->driver_data with pldat->mii_bus. When trying to remove
the driver, in lpc_eth_drv_remove(), platform_get_drvdata() will
return the pldat->mii_bus pointer and try to use it as a struct
net_device pointer. This causes unregister_netdev to segfault and
generate a kernel BUG. Is this reproducible?
Signed-off-by: Daniel Martinez <linux@danielsmartinez.com>
Signed-off-by: Bruno Carneiro da Cunha <brunocarneirodacunha@usp.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes that we've merged late, but for the most part that have
been sitting in -next for a while through platform maintainer trees:
- Fixes to suspend/resume on Tegra, caused by the added features this
merge window
- Cleanups and minor fixes to TI additions this merge window
- Tee fixes queued up late before the merge window, included here.
- A handful of other fixlets
There's also a refresh of the shareed config files (multi_v* on
32-bit, and defconfig on 64-bit), to avoid conflicts when we get new
contributions"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: multi_v7_defconfig: Restore debugfs support
ARM: defconfig: re-run savedefconfig on multi_v* configs
arm64: defconfig: re-run savedefconfig
ARM: pxa: Fix resource properties
soc: mediatek: cmdq: fixup wrong input order of write api
soc: aspeed: Fix snoop_file_poll()'s return type
MAINTAINERS: Switch to Marvell addresses
MAINTAINERS: update Cavium ThunderX drivers
Revert "arm64: dts: juno: add dma-ranges property"
MAINTAINERS: Make Nicolas Saenz Julienne the new bcm2835 maintainer
firmware: arm_scmi: Avoid double free in error flow
arm64: dts: juno: Fix UART frequency
ARM: dts: Fix sgx sysconfig register for omap4
arm: socfpga: execute cold reboot by default
ARM: dts: Fix vcsi regulator to be always-on for droid4 to prevent hangs
ARM: dts: dra7: fix cpsw mdio fck clock
ARM: dts: am57xx-beagle-x15: Update pinmux name to ddr_3_3v
ARM: dts: omap3-tao3530: Fix incorrect MMC card detection GPIO polarity
soc/tegra: pmc: Add reset sources and levels on Tegra194
soc/tegra: pmc: Add missing IRQ callbacks on Tegra194
...
|
|
The driver forgets to call pci_release_regions() in remove like that
in probe failure.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refer to the databook of DesignWare Cores Ethernet MAC Universal:
6.2.1.5 Register 4 (Transmit Descriptor List Address Register
If this register is not changed when the ST bit is set to 0, then
the DMA takes the descriptor address where it was stopped earlier.
The stmmac_tx_err() does zero indices to Tx descriptors, but does
not reset HW current Tx descriptor address. To fix inconsistency,
the base address of the Tx descriptors should be rewritten before
restarting Tx.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EEE support has not been enabled on ENETC, but it may connect
to a PHY which supports EEE and advertises EEE by default, while
its link partner also advertises EEE. If this happens, the PHY enters
low power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
ENETC connects to, to prevent the above unwanted outcome.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare second round of updates for 5.5 merge window.
|
|
Pull more drm updates from Dave Airlie:
"Rob pointed out I missed his pull request for msm-next, it's been in
next for a while outside of my tree so shouldn't cause any unexpected
issues, it has some OCMEM support in drivers/soc that is acked by
other maintainers as it's outside my tree.
Otherwise it's a usual fixes pull, i915, amdgpu, the main ones, with
some tegra, omap, mgag200 and one core fix.
Summary:
msm-next:
- OCMEM support for a3xx and a4xx GPUs.
- a510 support + display support
core:
- mst payload deletion fix
i915:
- uapi alignment fix
- fix for power usage regression due to security fixes
- change default preemption timeout to 640ms from 100ms
- EHL voltage level display fixes
- TGL DGL PHY fix
- gvt - MI_ATOMIC cmd parser fix, CFL non-priv warning
- CI spotted deadlock fix
- EHL port D programming fix
amdgpu:
- VRAM lost fixes on BACO for CI/VI
- navi14 DC fixes
- misc SR-IOV, gfx10 fixes
- XGMI fixes for arcturus
- SRIOV fixes
amdkfd:
- KFD on ppc64le enabled
- page table optimisations
radeon:
- fix for r1xx/2xx register checker.
tegra:
- displayport regression fixes
- DMA API regression fixes
mgag200:
- fix devices that can't scanout except at 0 addr
omap:
- fix dma_addr refcounting"
* tag 'drm-next-2019-12-06' of git://anongit.freedesktop.org/drm/drm: (100 commits)
drm/dp_mst: Correct the bug in drm_dp_update_payload_part1()
drm/omap: fix dma_addr refcounting
drm/tegra: Run hub cleanup on ->remove()
drm/tegra: sor: Make the +5V HDMI supply optional
drm/tegra: Silence expected errors on IOMMU attach
drm/tegra: vic: Export module device table
drm/tegra: sor: Implement system suspend/resume
drm/tegra: Use proper IOVA address for cursor image
drm/tegra: gem: Remove premature import restrictions
drm/tegra: gem: Properly pin imported buffers
drm/tegra: hub: Remove bogus connection mutex check
ia64: agp: Replace empty define with do while
agp: Add bridge parameter documentation
agp: remove unused variable num_segments
agp: move AGPGART_MINOR to include/linux/miscdevice.h
agp: remove unused variable size in agp_generic_create_gatt_table
drm/dp_mst: Fix build on systems with STACKTRACE_SUPPORT=n
drm/radeon: fix r1xx/r2xx register checker for POT textures
drm/amdgpu: fix GFX10 missing CSIB set(v3)
drm/amdgpu: should stop GFX ring in hw_fini
...
|
|
Pull more block and io_uring updates from Jens Axboe:
"I wasn't expecting this to be so big, and if I was, I would have used
separate branches for this. Going forward I'll be doing separate
branches for the current tree, just like for the next kernel version
tree. In any case, this contains:
- Series from Christoph that fixes an inherent race condition with
zoned devices and revalidation.
- null_blk zone size fix (Damien)
- Fix for a regression in this merge window that caused busy spins by
sending empty disk uevents (Eric)
- Fix for a regression in this merge window for bfq stats (Hou)
- Fix for io_uring creds allocation failure handling (me)
- io_uring -ERESTARTSYS send/recvmsg fix (me)
- Series that fixes the need for applications to retain state across
async request punts for io_uring. This one is a bit larger than I
would have hoped, but I think it's important we get this fixed for
5.5.
- connect(2) improvement for io_uring, handling EINPROGRESS instead
of having applications needing to poll for it (me)
- Have io_uring use a hash for poll requests instead of an rbtree.
This turned out to work much better in practice, so I think we
should make the switch now. For some workloads, even with a fair
amount of cancellations, the insertion sort is just too expensive.
(me)
- Various little io_uring fixes (me, Jackie, Pavel, LimingWu)
- Fix for brd unaligned IO, and a warning for the future (Ming)
- Fix for a bio integrity data leak (Justin)
- bvec_iter_advance() improvement (Pavel)
- Xen blkback page unmap fix (SeongJae)
The major items in here are all well tested, and on the liburing side
we continue to add regression and feature test cases. We're up to 50
topic cases now, each with anywhere from 1 to more than 10 cases in
each"
* tag 'for-linus-20191205' of git://git.kernel.dk/linux-block: (33 commits)
block: fix memleak of bio integrity data
io_uring: fix a typo in a comment
bfq-iosched: Ensure bio->bi_blkg is valid before using it
io_uring: hook all linked requests via link_list
io_uring: fix error handling in io_queue_link_head
io_uring: use hash table for poll command lookups
io-wq: clear node->next on list deletion
io_uring: ensure deferred timeouts copy necessary data
io_uring: allow IO_SQE_* flags on IORING_OP_TIMEOUT
null_blk: remove unused variable warning on !CONFIG_BLK_DEV_ZONED
brd: warn on un-aligned buffer
brd: remove max_hw_sectors queue limit
xen/blkback: Avoid unmapping unmapped grant pages
io_uring: handle connect -EINPROGRESS like -EAGAIN
block: set the zone size in blk_revalidate_disk_zones atomically
block: don't handle bio based drivers in blk_revalidate_disk_zones
block: allocate the zone bitmaps lazily
block: replace seq_zones_bitmap with conv_zones_bitmap
block: simplify blkdev_nr_zones
block: remove the empty line at the end of blk-zoned.c
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
memory: tegra: Fixes for v5.5-rc1
This contains a fix for a kernel panic that can occur on suspend if EMC
timings are not available in device tree.
* tag 'tegra-for-5.5-memory-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
memory: tegra30-emc: Fix panic on suspend
Link: https://lore.kernel.org/r/20191204130753.3614278-1-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
soc/tegra: Fixes for v5.5-rc1
Fixes a regression for wake events on Tegra194 caused by the Tegra210
support that was added in v5.5-rc1 as well as wrong reset sources and
levels on Tegra194.
* tag 'tegra-for-5.5-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Add reset sources and levels on Tegra194
soc/tegra: pmc: Add missing IRQ callbacks on Tegra194
soc/tegra: pmc: Use lower-case for hexadecimal literals
Link: https://lore.kernel.org/r/20191204130753.3614278-2-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
cpufreq: tegra: Changes for v5.5-rc1
Implements support for suspend/resume on Tegra124.
* tag 'tegra-for-5.5-cpufreq' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
cpufreq: tegra124: Add suspend and resume support
Link: https://lore.kernel.org/r/20191204130753.3614278-3-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few ti-sysc related fixes for v5.5 merge window
Just few minor changes that can be merged when suitable, but would
be good to have these in v5.5-rc1 to remove dependencies between branches
for more changes later on in v5.6:
- Add quirk handling for AESS (Audio Engine Sub System)
- We want to drop the useless gptimer option for omap4 as there are local
timers
- A minor error path handling improvment for sysc_child_add_named_clock()
that will make further patching a bit easier
* tag 'omap-for-v5.5/ti-sysc-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Adjust exception handling in sysc_child_add_named_clock()
ARM: OMAP2+: Drop useless gptimer option for omap4
bus: ti-sysc: Add module enable quirk for audio AESS
Link: https://lore.kernel.org/r/pull-1574273726-31367@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-next
- Includes gvt-next-fixes-2019-12-02 pull
- Fixes for CI spotted eadlock and a race condition in GEM contexts
- Fix for EHL port D programming
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191205092412.GA8089@jlahtine-desk.ger.corp.intel.com
|
|
sock_fprog_kern::len is in units of struct sock_filter, not bytes.
Fixes: 3e859adf3643 ("compat_ioctl: unify copy-in of ppp filters")
Reported-by: syzbot+eb853b51b10f1befa0b7@syzkaller.appspotmail.com
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, when set VF VLAN with command "ip link set <pf name>
vf <vf id> vlan <vlan id>", the VF ID 0 is handled as PF incorrectly,
which should be the first VF. This patch fixes it.
Fixes: 21e043cd8124 ("net: hns3: fix set port based VLAN for PF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, hns3_nic_maybe_stop_tx() uses skb_copy() to linearize a
SKB if the BD num required by the SKB does not meet the hardware
limitation, and it linearizes the SKB by allocating a new linearized SKB
and freeing the old SKB, if hns3_nic_maybe_stop_tx() returns -EBUSY
because there are no enough space in the ring to send the linearized
skb to hardware, the sch_direct_xmit() still hold reference to old SKB
and try to retransmit the old SKB when dev_hard_start_xmit() return
TX_BUSY, which may cause use after freed problem.
This patch fixes it by using __skb_linearize() to linearize the
SKB in hns3_nic_maybe_stop_tx().
Fixes: 51e8439f3496 ("net: hns3: add 8 BD limit for tx flow")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is timing window between ring_space checking and
netif_stop_subqueue when transmiting a SKB, and the TX BD
cleaning may be executed during the time window, which may
caused TX queue not restarted problem.
This patch fixes it by rechecking the ring_space after
netif_stop_subqueue to make sure TX queue is restarted.
Also, the ring->next_to_clean is updated even when pkts is
zero, because all the TX BD cleaned may be non-SKB, so it
needs to check if TX queue need to be restarted.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for NET_SWITCHDEV
Replace "select NET_SWITCHDEV" vs "depends on NET_SWITCHDEV" to fix Kconfig
warning with CONFIG_COMPILE_TEST=y
WARNING: unmet direct dependencies detected for NET_SWITCHDEV
Depends on [n]: NET [=y] && INET [=n]
Selected by [y]:
- TI_CPSW_SWITCHDEV [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && (ARCH_DAVINCI || ARCH_OMAP2PLUS || COMPILE_TEST [=y])
because TI_CPSW_SWITCHDEV blindly selects NET_SWITCHDEV even though
INET is not set/enabled, while NET_SWITCHDEV depends on INET.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This brings in the mainline tree right after armsoc contents was merged
this release cycle, so that we can re-run savedefconfig, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull ceph updates from Ilya Dryomov:
"The two highlights are a set of improvements to how rbd read-only
mappings are handled and a conversion to the new mount API (slightly
complicated by the fact that we had a common option parsing framework
that called out into rbd and the filesystem instead of them calling
into it).
Also included a few scattered fixes and a MAINTAINERS update for rbd,
adding Dongsheng as a reviewer"
* tag 'ceph-for-5.5-rc1' of git://github.com/ceph/ceph-client:
libceph, rbd, ceph: convert to use the new mount API
rbd: ask for a weaker incompat mask for read-only mappings
rbd: don't query snapshot features
rbd: remove snapshot existence validation code
rbd: don't establish watch for read-only mappings
rbd: don't acquire exclusive lock for read-only mappings
rbd: disallow read-write partitions on images mapped read-only
rbd: treat images mapped read-only seriously
rbd: introduce RBD_DEV_FLAG_READONLY
rbd: introduce rbd_is_snap()
ceph: don't leave ino field in ceph_mds_request_head uninitialized
ceph: tone down loglevel on ceph_mdsc_build_path warning
rbd: update MAINTAINERS info
ceph: fix geting random mds from mdsmap
rbd: fix spelling mistake "requeueing" -> "requeuing"
ceph: make several helper accessors take const pointers
libceph: drop unnecessary check from dispatch() in mon_client.c
|
|
In cited commit, when prio tag mode is enabled, FTE creation fails
due to missing group with valid match criteria.
Hence,
(a) create prio tag group metadata_prio_tag_grp when prio tag is
enabled with match criteria for vlan push FTE.
(b) Rename metadata_grp to metadata_allmatch_grp to reflect its purpose.
Also when priority tag is enabled, delete metadata settings after
deleting ingress rules, which are using it.
Tide up rest of the ingress config code for unnecessary labels.
Fixes: 10652f39943e ("net/mlx5: Refactor ingress acl configuration")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When setting speed to 100G via ethtool (AN is set to off), only 25G*4 is
configured while the user, who has an advanced HW which supports
extended PTYS, expects also 50G*2 to be configured.
With this patch, when extended PTYS mode is available, configure
PTYS via extended fields.
Fixes: 4b95840a6ced ("net/mlx5e: Fix matching of speed to PRM link modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add a missing value in translation of PTYS ext_eth_proto_oper to its
corresponding speed. When ext_eth_proto_oper bit 10 is set, ethtool
shows unknown speed. With this fix, ethtool shows speed is 100G as
expected.
Fixes: a08b4ed1373d ("net/mlx5: Add support to ext_* fields introduced in Port Type and Speed register")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
It could be neigh update flow took a refcount on peer flow so
sometimes we cannot release peer flow even if parent flow is
being freed now.
Fixes: 5a7e5bcb663d ("net/mlx5e: Extend tc flow struct with reference counter")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Flows are allocated with kzalloc() so free with kfree().
Fixes: 04de7dda7394 ("net/mlx5e: Infrastructure for duplicated offloading of TC flows")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
SFF 8472 eeprom length is 512 bytes. Fix module info return value to
support 512 bytes read.
Fixes: ace329f4ab3b ("net/mlx5e: ethtool, Remove unsupported SFP EEPROM high pages query")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When the user changes prio2buffer mapping while global pause is
enabled, mlx5 driver incorrectly sets all active buffers
(buffer that has at least one priority mapped) to lossy.
Solution:
If global pause is enabled, set all the active buffers to lossless
in prio2buffer command.
Also, add error message when buffer size is not enough to meet
xoff threshold.
Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Cited patch changed (channel index, tc) => (TXQ index) mapping to be a
static one, in order to keep indices consistent when changing number of
channels or TCs.
For 32 channels (OOB) and 8 TCs, real num of TXQs is 256.
When reducing the amount of channels to 8, the real num of TXQs will be
changed to 64.
This indices method is buggy:
- Channel #0, TC 3, the TXQ index is 96.
- Index 8 is not valid, as there is no such TXQ from driver perspective
(As it represents channel #8, TC 0, which is not valid with the above
configuration).
As part of driver's select queue, it calls netdev_pick_tx which returns an
index in the range of real number of TXQs. Depends on the return value,
with the examples above, driver could have returned index larger than the
real number of tx queues, or crash the kernel as it tries to read invalid
address of SQ which was not allocated.
Fix that by allocating sequential TXQ indices, and hold a new mapping
between (channel index, tc) => (real TXQ index). This mapping will be
updated as part of priv channels activation, and is used in
mlx5e_select_queue to find the selected queue index.
The existing indices mapping (channel_tc2txq) is no longer needed, as it
is used only for statistics structures and can be calculated on run time.
Delete its definintion and updates.
Fixes: 8bfaf07f7806 ("net/mlx5e: Present SW stats when state is not opened")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The cio layer's intparm logic does not align itself well with how qeth
manages cmd IOs. When an active IO gets terminated via halt/clear, the
corresponding IRQ's intparm does not reflect the cmd buffer but rather
the intparm that was passed to ccw_device_halt() / ccw_device_clear().
This behaviour was recently clarified in
commit b91d9e67e50b ("s390/cio: fix intparm documentation").
As a result, qeth_irq() currently doesn't cancel a cmd that was
terminated via halt/clear. This primarily causes us to leak
card->read_cmd after the qeth device is removed, since our IO path still
holds a refcount for this cmd.
For qeth this means that we need to keep track of which IO is pending on
a device ('active_cmd'), and use this as the intparm when calling
halt/clear. Otherwise qeth_irq() can't match the subsequent IRQ to its
cmd buffer.
Since we now keep track of the _expected_ intparm, we can also detect
any mismatch; this would constitute a bug somewhere in the lower layers.
In this case cancel the active cmd - we effectively "lost" the IRQ and
should not expect any further notification for this IO.
Fixes: 405548959cc7 ("s390/qeth: add support for dynamically allocated cmds")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the RX path builds non-linear skbs, the packet headers can
currently spill over into page fragments. Depending on the packet type
and what fields we need to access in the headers, this could cause us
to go past the end of skb->data.
So for non-linear packets, copy precisely the length of the necessary
headers ('linear_len') into skb->data.
And don't copy more, upper-level protocols will peel whatever additional
packet headers they need.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depending on a packet's type, the RX path needs to access fields in the
packet headers and thus requires a minimum packet length.
Enforce this length when building the skb.
On the other hand a single runt packet is no reason to drop the whole
RX buffer. So just skip it, and continue processing on the next packet.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 2b3e88ea6528 ("net: phy: improve phy state checking")
phy_start_aneg() expects phy state to be >= PHY_UP. Call phy_start()
before calling phy_start_aneg() during probe so that autonegotiation
is initiated.
As phy_start() takes care of calling phy_start_aneg(), drop the explicit
call to phy_start_aneg().
Network fails without this patch on Octeon TX.
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ARM Device-tree updates from Olof Johansson:
"As always, the bulk of updates. Some of the news this cycle:
New SoC descriptions:
- Broadcom BCM2711
- Amlogic Meson A1 and G12
- Freescale S32V234
- Marvell Armada AP807/AP807-quad and CP115
- Realtek RTD1293 and RTD1296
- Rockchip RK3308
New boards and platforms:
- Allwinner: NanoPi Duo2
- Amlogic: Ugoos am6
- Atmel at91: Overkiz Kizbox2/4
- Broadcom: RPi4, Luxul XWC-2000
- Marvell: New Espressobin flavor
- NXP: i.MX8MN LPDDR4 EVK, i.MX8QXP Colibri, S32V234 EVB, Netronix
E60K02 and Kobo Clara HD, Kontron N6311 and N6411, OPOS6UL and
OPOS6ULDev
- Renesas: Salvator-XS
- Rockchip: Beelink A1 (rk3308), rk3308 eval boards, rk3399-roc-pc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (653 commits)
ARM: dts: logicpd-torpedo: Disable USB Host
arm: dts: mt6323: add keys, power-controller, rtc and codec
arm64: dts: mt8183: add systimer0 device node
dt-bindings: mediatek: update bindings for MT8183 systimer
arm64: dts: rockchip: fix sdmmc detection on boot on rk3328-roc-cc
arm64: dts: rockchip: Split rk3399-roc-pc for with and without mezzanine board.
arm64: dts: rockchip: Add Beelink A1
dt-bindings: ARM: rockchip: Add Beelink A1
arm64: dts: rockchip: Add RK3328 audio pipelines
arm64: dts: ti: k3-j721e-common-proc-board: Add USB ports
arm64: dts: ti: k3-j721e-main: add USB controller nodes
ARM: dts: aspeed-g6: Add timer description
ARM: dts: aspeed: ast2600evb: Enable i2c buses
ARM: dts: at91: add a dts and dtsi file for kizbox2 based boards
dt-bindings: arm: at91: Document Kizbox2-2 board binding
arm64: dts: meson-gx: fix i2c compatible
arm64: dts: meson-gx: cec node should be disabled by default
arm64: dts: meson-g12b-odroid-n2: add missing amlogic, s922x compatible
arm64: dts: meson-gxm: fix gpu irq order
arm64: dts: meson-g12a: fix gpu irq order
...
|
