summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2013-10-03atl1e: enable support for NETIF_F_RXALL and NETIF_F_RXCRC featuresAndrea Merello
This patch allows (optionally, via ethtool) the atl1e NIC to: - Receive bad frames (runt, bad-fcs, etc..) - Receive full frames without stripping the FCS. This has been tested on my board by injecting runt and bad-fcs frames with a FPGA-based device. The particular scenario of receiving very short frames (<4 bytes) without passing FCS to the upper layer has been also tested: This could be potentially dangerous because the driver performs a 4 byte subtraction on the frame length, but I finally have NOT added anything to avoid this because it seems the NIC always discards frames so much short.. If someone still have some reason to worry about this, please tell me.. I will add an explicit SW check.. Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-03wireless: rt2x00: rt2800usb: add new devicesXose Vazquez Perez
0411,0241 RT5572 BUFFALO WI-U2-300D Wireless LAN Adapter 0789,0170 RT3572 Logitec LAN-W300AN/U2 0846,9013 RT3573 NETGEAR Adaptador USB Inalambrico Movistar 0df6,006e RT3573 Sitecom WiFi USB adapter N900 2001,3c1f RT3573 D-Link DWA-162 Wireless N900 Dual Band Adapter 2001,3c20 RT5372 D-Link DWA-140 Wireless N USB Adapter(rev.D) 2001,3c21 RT5572 D-Link DWA-160 Xtreme N Dual Band USB Adapter(rev.C) 2001,3c22 RT5372 D-Link DWA-132 Wireless N USB Adapter(rev.B) 2001,3c23 RT5372 D-Link GO-USB-N300 Wireless N Easy USB Adapter 2019,ab29 ? Planex GW-USMirco300 20f4,724a RT5572 TRENDnet N600 Wireless Dual Band USB Adapter Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: users@rt2x00.serialmonkey.com Cc: linux-wireless@vger.kernel.org Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: rtl8188ee: Convert driver to use new ↵Larry Finger
rtl_phy_scan_operation_backup() routine Now that rtl_phy_scan_operation_backup() exists, convert rtl8188ee to use it. Routine rtl88e_phy_scan_operation_backup() is no longer used and is removed. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: rtl8723ae: Convert driver to use new ↵Larry Finger
rtl_phy_scan_operation_backup() routine Now that rtl_phy_scan_operation_backup() exists, convert rtl8723ae to use it. Routine rtl8723ae_phy_scan_operation_backup() is no longer used and is removed. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: rtl8192ce: Convert driver to use new ↵Larry Finger
rtl_phy_scan_operation_backup() routine Now that rtl_phy_scan_operation_backup() exists, convert rtl8192de to use it. Routine rtl92d_phy_scan_operation_backup() is no longer used and is removed. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: rtl8192c: Remove rtl8192c_phy_scan_operation_backup()Larry Finger
Drivers rtl8192ce and rtl8192cu no longer rely on this routine. It is removed. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: rtl8192ce: Convert driver to use new ↵Larry Finger
rtl_phy_scan_operation_backup() routine Now that rtl_phy_scan_operation_backup() exists, convert rtl8192ce to use it. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: rtl8192cu: Convert to use new rtl_phy_scan_operation_backup() routineLarry Finger
Now that the routine exists in driver rtlwifi, convert rtl8192cu to use it. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: Implement a common rtl_phy_scan_operation_backup() routineLarry Finger
Several of the drivers supported by rtlwifi individually implement the same routine that supports scans. As a first step, create this routine in driver rtlwifi. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: Remove all remaining references to variable 'noise' in rtl_stats structLarry Finger
This completes removal of all places that reference variable 'noise' in the rtl_stats struct. The definition of the struct is unchanged. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: rtl8188ee: Fix smatch warning in rtl8188ee/hw.cLarry Finger
Smatch lists the following: CHECK drivers/net/wireless/rtlwifi/rtl8188ee/hw.c drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:149 _rtl88ee_set_fw_clock_on() info: ignoring unreachable code. drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:149 _rtl88ee_set_fw_clock_on() info: ignoring unreachable code. This info message is the result of a real error due to a missing break statement in a "while (1)" loop. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [3.10+] Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: Fix smatch warnings in usb.cLarry Finger
Smatch displays the following: CHECK drivers/net/wireless/rtlwifi/usb.c drivers/net/wireless/rtlwifi/usb.c:458 _rtl_usb_rx_process_agg() warn: assigning (-98) to unsigned variable 'stats.noise' drivers/net/wireless/rtlwifi/usb.c:503 _rtl_usb_rx_process_noagg() warn: assigning (-98) to unsigned variable 'stats.noise' drivers/net/wireless/rtlwifi/usb.c:596 _rtl_rx_get_padding() info: ignoring unreachable code. drivers/net/wireless/rtlwifi/usb.c:596 _rtl_rx_get_padding() info: ignoring unreachable code. The variable 'stats.noise' is not used, thus the initializers are removed. The unreachable code info is fixed by including the appropriate section inside #ifdef .. #endif constructions. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: Fix smatch warning in pci.cLarry Finger
Smatch reports the following: CHECK drivers/net/wireless/rtlwifi/pci.c drivers/net/wireless/rtlwifi/pci.c:739 _rtl_pci_rx_interrupt() warn: assigning (-98) to unsigned variable 'stats.noise' The variable 'stats.noise' is not used. That initializer is removed. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: rtl8192_common: Fix smatch errors and warnings in rtl8192c/dm_common.cLarry Finger
Smatch lists the following: CHECK drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:551 rtl92c_dm_pwdb_monitor() info: ignoring unreachable code. drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:551 rtl92c_dm_pwdb_monitor() info: ignoring unreachable code. drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:870 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:870 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:882 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:883 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:891 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:892 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2 The unreachable code message is fixed by deleting the code that follows a return. The errors are fixed by increasing the size of txpwr_level. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: rtl8192cu: Fix smatch warning in rtl8192cu/trx.cLarry Finger
Smatch lists the following: CHECK drivers/net/wireless/rtlwifi/rtl8192cu/trx.c drivers/net/wireless/rtlwifi/rtl8192cu/trx.c:367 _rtl_rx_process() warn: assigning (-98) to unsigned variable 'stats.noise' This variable is unused, thus the initializer is removed, as well as a comment referring to that variable. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: rtl8192de: Fix smatch warnings in rtl8192de/hw.cLarry Finger
Smatch lists the following: CHECK drivers/net/wireless/rtlwifi/rtl8192de/hw.c drivers/net/wireless/rtlwifi/rtl8192de/hw.c:1200 rtl92de_set_qos() info: ignoring unreachable code. drivers/net/wireless/rtlwifi/rtl8192de/hw.c:1200 rtl92de_set_qos() info: ignoring unreachable code. The dead code is deleted. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rtlwifi: rtl8192du: Fix smatch errors in /rtl8192de/dm.cLarry Finger
Smatch lists the following: CHECK drivers/net/wireless/rtlwifi/rtl8192de/dm.c drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1054 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'ofdm_index' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1056 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'ofdm_index' 2 <= 2 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1126 rtl92d_dm_txpower_tracking_callback_thermalmeter() debug: remove_pools: nr_children over 4000 (4596). (rtlpriv->dbg.global_debuglevel merged) drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1126 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1129 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1132 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1135 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1138 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1141 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1144 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1147 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1151 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1154 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1157 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1160 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1163 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1166 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1169 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1172 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255 This patch fixes several off-by-one errors. It also removes a comment referencing variable 'noise' in the rts_stats struct. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03rt2800: add support for radio chip RF3070Stanislaw Gruszka
Add support for new RF chip ID: 3070. It seems to be the same as 5370, maybe vendor just put wrong value on the eeprom, but add this id anyway since devices with it showed on the marked. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03brcmfmac: rework rx path bus interfaceArend van Spriel
The brcmfmac has common and bus specific part. The rx function api was using sk_buff_head. Changed to sk_buff instead. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03brcmfmac: Use fw filename and nvram based of devid for sdio.Hante Meuleman
SDIO firmware download routines uses one name for firmware file and nvram file for all sdio devices. This is not user friendly. Use fw filename and nvram filename based upon chip id and revision. Reported-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03brcmfmac: fix sparse error 'bad constant expression'Arend van Spriel
The definition of BRCMF_EVENTING_MASK_LEN results in a sparse error message .../fweh.c:331:22: error: bad constant expression .../fweh.c:388:22: error: bad constant expression .../dhd_common.c:256:22: error: bad constant expression This is caused by the use of roundup() in BRCMF_EVENTING_MASK_LEN and it is used to allocate an array variable on the stack. Better use DIV_ROUND_UP() macro. Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03brcmfmac: reserve memory for bus layer in sk_buff::cbFranky Lin
Bus layer need to share sk_buff::cb with firmware signal feature. Reserve necessary memory so they won't overwrite each other. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03brcmfmac: add valid core index check in related functionsFranky Lin
Perform a valid check for core index to avoid illegal address access. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03brcmfmac: add BCM4339 SDIO interface supportFranky Lin
BCM4339 is an a/b/g/n/ac 1x1 WiFi chip. This patch adds support for it through SDIO interface. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03brcmfmac: sync firmware event listFranky Lin
Update event list to keep sync with firmware development. Use calculated event mask length instead of hard-coded value. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03Merge branch 'for-upstream' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
2013-10-03Merge tag 'for-linville-20131001' of git://github.com/kvalo/athJohn W. Linville
2013-10-03Merge branch 'for-linville' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/luca/wl12xx
2013-10-03Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
2013-10-033com: Fix drivers/net/ethernet/3com/Kconfig references to PCMCIA and 3c515Matthew Whitehead
The Vortex driver works with PCI and Cardbus devices, not PCMCIA. There never was an EISA 3c515 card, only ISA, so remove that option. Signed-off-by: Matthew Whitehead <tedheadster@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-03net: myri10ge: Change variable type to boolPeter Senna Tschudin
There is the rc variable on both myri10ge_ss_lock_napi and myri10ge_ss_lock_poll functions. In both cases rc is only assigned the values true and false. Both functions already return bool. Change rc type to bool. The simplified semantic patch that find this problem is as follows (http://coccinelle.lip6.fr/): @exists@ type T; identifier b; @@ - T + bool b = ...; ... when any b = \(true\|false\) Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-03net: bnx2x: Change variable type to boolPeter Senna Tschudin
The variable rc is only assigned the values true and false. The function bnx2x_prev_is_path_marked already returns bool. Change rc type to bool. The simplified semantic patch that find this problem is as follows (http://coccinelle.lip6.fr/): @exists@ type T; identifier b; @@ - T + bool b = ...; ... when any b = \(true\|false\) Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-03net: atl1c: Change variable type to boolPeter Senna Tschudin
The variable ret is only assigned the values true and false. The function atl1c_read_eeprom already returns bool. Change ret type to bool. The simplified semantic patch that find this problem is as follows (http://coccinelle.lip6.fr/): @exists@ type T; identifier b; @@ - T + bool b = ...; ... when any b = \(true\|false\) Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-03bonding: modify the old and add new xmit hash policiesNikolay Aleksandrov
This patch adds two new hash policy modes which use skb_flow_dissect: 3 - Encapsulated layer 2+3 4 - Encapsulated layer 3+4 There should be a good improvement for tunnel users in those modes. It also changes the old hash functions to: hash ^= (__force u32)flow.dst ^ (__force u32)flow.src; hash ^= (hash >> 16); hash ^= (hash >> 8); Where hash will be initialized either to L2 hash, that is SRCMAC[5] XOR DSTMAC[5], or to flow->ports which should be extracted from the upper layer. Flow's dst and src are also extracted based on the xmit policy either directly from the buffer or by using skb_flow_dissect, but in both cases if the protocol is IPv6 then dst and src are obtained by ipv6_addr_hash() on the real addresses. In case of a non-dissectable packet, the algorithms fall back to L2 hashing. The bond_set_mode_ops() function is now obsolete and thus deleted because it was used only to set the proper hash policy. Also we trim a pointer from struct bonding because we no longer need to keep the hash function, now there's only a single hash function - bond_xmit_hash that works based on bond->params.xmit_policy. The hash function and skb_flow_dissect were suggested by Eric Dumazet. The layer names were suggested by Andy Gospodarek, because I suck at semantics. Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02ath10k: wmi: Convert use of 6 to ETH_ALENJoe Perches
Use the appropriate define instead of 6. Signed-off-by: Joe Perches <joe@perches.com> Noticed-by: Julia Lawall <julia.lawall@lip6.fr> via spatch script Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02net: mv643xx_eth: fix missing device_node for port devicesSebastian Hesselbarth
DT-based mv643xx_eth probes and creates platform_devices for the port devices on its own. To allow fixups for ports based on the device_node, we need to set .of_node of the corresponding device with the correct node. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02net: mv643xx_eth: fix orphaned statistics timer crashSebastian Hesselbarth
The periodic statistics timer gets started at port _probe() time, but is stopped on _stop() only. In a modular environment, this can cause the timer to access already deallocated memory, if the module is unloaded without starting the eth device. To fix this, we add the timer right before the port is started, instead of at _probe() time. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02net: mv643xx_eth: update statistics timer from timer context onlySebastian Hesselbarth
Each port driver installs a periodic timer to update port statistics by calling mib_counters_update. As mib_counters_update is also called from non-timer context, we should not reschedule the timer there but rather move it to timer-only context. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02net:drivers/net: Miscellaneous conversions to ETH_ALENJoe Perches
Convert the memset/memcpy uses of 6 to ETH_ALEN where appropriate. Also convert some struct definitions and u8 array declarations of [6] to ETH_ALEN. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02igb: Avoid uninitialized advertised variable in eee_set_curAndi Kleen
eee_get_cur assumes that the output data is already zeroed. It can read-modify-write the advertised field: if (ipcnfg & E1000_IPCNFG_EEE_100M_AN) 2594 edata->advertised |= ADVERTISED_100baseT_Full; This is ok for the normal ethtool eee_get call, which always zeroes the input data before. But eee_set_cur also calls eee_get_cur and it did not zero the input field. Later on it then compares agsinst the field, which can contain partial stack garbage. Zero the input field in eee_set_cur() too. Cc: jeffrey.t.kirsher@intel.com Cc: netdev@vger.kernel.org Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02net: calxedaxgmac: determine number of address filters at runtimeRob Herring
Highbank and Midway xgmac h/w have different number of MAC address filter registers with 7 and 31, respectively. Highbank has been wrong, so fix it and detect the number of filter registers at run-time. Unfortunately, the version register is the same on both SOCs, so simply test if write to the last filter register will take a value. It always reads as 0 if not. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02net: calxedaxgmac: add uc and mc filter addresses in promiscuous modeRob Herring
Even in promiscuous mode, we need to add filter addresses for correct operation. This fixes silent failures when using a bridge and adding addresses using the "bridge fdb add" command. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02net: calxedaxgmac: fix clearing of old filter addressesRob Herring
In commit 2ee68f621af280 (net: calxedaxgmac: fix various errors in xgmac_set_rx_mode), a fix to clean-up old address entries was added. However, the loop to zero out the entries failed to increment the register address resulting in only 1 entry getting cleared. Fix this to correctly use the loop index. Also, the end of the loop condition was off by 1 and should have been <= rather than <. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02connector: use 'size' everywhere in cn_netlink_send()Mathias Krause
We calculated the size for the netlink message buffer as size. Use size in the memcpy() call as well instead of recalculating it. Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02connector: use nlmsg_len() to check message lengthMathias Krause
The current code tests the length of the whole netlink message to be at least as long to fit a cn_msg. This is wrong as nlmsg_len includes the length of the netlink message header. Use nlmsg_len() instead to fix this "off-by-NLMSG_HDRLEN" size check. Cc: stable@vger.kernel.org # v2.6.14+ Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02proc connector: fix info leaksMathias Krause
Initialize event_data for all possible message types to prevent leaking kernel stack contents to userland (up to 20 bytes). Also set the flags member of the connector message to 0 to prevent leaking two more stack bytes this way. Cc: stable@vger.kernel.org # v2.6.15+ Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02isdn: eicon: free pointer after using it in log msg in ↵Jesper Juhl
divas_um_idi_delete_entity() Not really a problem, but nice IMHO; the Coverity static analyzer complains that we use the pointer 'e' after it has been freed, so move the freeing below the final use, even if that use is just using the value of the pointer and not actually dereferencing it. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02xen-netfront: convert to GRO APIWei Liu
Anirban was seeing netfront received MTU size packets, which downgraded throughput. The following patch makes netfront use GRO API which improves throughput for that case. Signed-off-by: Wei Liu <wei.liu2@citrix.com> Cc: Anirban Chakraborty <abchak@juniper.net> Cc: Ian Campbell <ian.campbell@citrix.com> Acked-by: Konrad Wilk <konrad.wilk@oracle.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02tg3: use phylib when robo switch is in useHauke Mehrtens
When a switch is connected as a PHY to the MAC driven by tg3, use phylib and provide the phy address to tg3 from the sprom. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02tg3: add support a phy at an address different than 01Hauke Mehrtens
When phylib was in use tg3 only searched at address 01 on the mdio bus and did not work with any other address. On the BCM4705 SoCs the switch is connected as a PHY behind the MAC driven by tg3 and it is at PHY address 30 in most cases. This is a preparation patch to allow support for such switches. phy_addr is set to TG3_PHY_MII_ADDR for all devices, which are using phylib, so this should not change any behavior. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-23 08:54:06 +0000