| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
|
|
set_memory_* functions have moved to set_memory.h. Switch to this
explicitly.
Link: http://lkml.kernel.org/r/1488920133-27229-10-git-send-email-labbott@redhat.com
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In some SoCs, setting noreboot bit needs modification to
PMC GC registers. But not all PMC drivers allow other drivers
to memory map their GC region. This could create mem request
conflict in watchdog driver. So this patch adds facility to allow
PMC drivers to pass noreboot update function to watchdog
drivers via platform data.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
iTCO_wdt no_reboot_bit set/unset functions has lot of common code between
them. So merging these two functions into a single update function would
remove these unnecessary code duplications. This patch fixes this issue
by creating a no_reboot_bit update function to handle both set/unset
functions.
Also checking for iTCO version every time you make no_reboot_bit set/unset
call is inefficient and makes the code look complex. This can be improved
by performing this check once during device probe and selecting the
appropriate no_reboot_bit update function. This patch fixes this issue
by splitting the update function into multiple helper functions.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/watchdog/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
cc: Wim Van Sebroeck <wim@iguana.be>
cc: Zwane Mwaikambo <zwanem@gmail.com>
cc: linux-watchdog@vger.kernel.org
|
|
The retu watchdog calls into the respective mfd driver, but fails to
link if that is diabled:
drivers/watchdog/built-in.o: In function `retu_wdt_set_timeout':
ziirave_wdt.c:(.text+0x8c88): undefined reference to `retu_write'
ziirave_wdt.c:(.text+0x8c88): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `retu_write'
drivers/watchdog/built-in.o: In function `retu_wdt_start':
ziirave_wdt.c:(.text+0x8cc8): undefined reference to `retu_write'
ziirave_wdt.c:(.text+0x8cc8): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `retu_write'
This restores the dependency as it was before
Fixes: da2a68b3eb47 ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
When the db8500 watchdog is enabled without the PRCMU, we get a lot of
warnings about duplicate or missing helper functions:
In file included from drivers/watchdog/ux500_wdt.c:21:0:
include/linux/mfd/dbx500-prcmu.h:422:19: error: redefinition of 'prcmu_abb_read'
static inline int prcmu_abb_read(u8 slave, u8 reg, u8 *value, u8 size)
This restores the dependency as it was.
Fixes: da2a68b3eb47 ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
gcc-4.3 can't decide whether the constant value in
kempld_prescaler[PRESCALER_21] is built-time constant or
not, and gets confused by the logic in do_div():
drivers/watchdog/kempld_wdt.o: In function `kempld_wdt_set_stage_timeout':
kempld_wdt.c:(.text.kempld_wdt_set_stage_timeout+0x130): undefined reference to `__aeabi_uldivmod'
This adds a call to ACCESS_ONCE() to force it to not consider
it to be constant, and leaves the more efficient normal case
in place for modern compilers, using an #ifdef to annotate
why we do this hack.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Checking for timer expiration is done from the softirq TIMER_SOFTIRQ.
Since commit 4cd13c21b207 ("softirq: Let ksoftirqd do its job"),
pending softirqs are no longer always handled immediately, instead,
if there are pending softirqs, and ksoftirqd is in state TASK_RUNNING,
the handling of the softirqs are deferred, and are instead supposed
to be handled by ksoftirqd, when ksoftirqd gets scheduled.
If a user space process with a real-time policy starts to misbehave
by never relinquishing the CPU while ksoftirqd is in state TASK_RUNNING,
what will happen is that all softirqs will get deferred, while ksoftirqd,
which is supposed to handle the deferred softirqs, will never get to run.
To make sure that the watchdog is able to fire even when we do not get
to run softirqs, replace the timers with hrtimers.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The kempld watchdog driver requires the respective MFD driver:
drivers/watchdog/built-in.o: In function `kempld_wdt_probe':
kempld_wdt.c:(.text+0x5c78): undefined reference to `kempld_get_mutex'
kempld_wdt.c:(.text+0x5c84): undefined reference to `kempld_read8'
kempld_wdt.c:(.text+0x5c8e): undefined reference to `kempld_release_mutex'
kempld_wdt.c:(.text+0x5d1c): undefined reference to `kempld_read8'
kempld_wdt.c:(.text+0x5d2c): undefined reference to `kempld_write8'
This adds the Kconfig dependency back.
Fixes: da2a68b3eb47 ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Without CONFIG_OF, the driver fails to link:
drivers/watchdog/built-in.o: In function `bcm2835_power_off':
bcm2835_wdt.c:(.text+0x1946): undefined reference to `of_find_device_by_node'
This adds a new dependency, to allow the COMPILE_TEST check to succeed.
Fixes: da2a68b3eb47 ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The driver fails to link if ARM_AMBA is disabled:
drivers/watchdog/sp805_wdt.o: In function `sp805_wdt_driver_init':
sp805_wdt.c:(.init.text+0x4): undefined reference to `amba_driver_register'
It seems that the COMPILE_TEST was added in the wrong place, as there
is no architecture dependency, but a bus dependency. This moves
the dependency accordingly.
Fixes: da2a68b3eb47 ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver fails to link when CONFIG_I2C is disabled or a loadable module while
the watchdog is built-in:
drivers/watchdog/built-in.o: In function `menf21bmc_wdt_shutdown':
menf21bmc_wdt.c:(.text+0x9b44): undefined reference to `i2c_smbus_write_word_data'
menf21bmc_wdt.c:(.text+0x9b44): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `i2c_smbus_write_word_data'
This adds a Kconfig dependency for it, to enforce a valid configuration.
Fixes: da2a68b3eb47 ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Wtihout CONFIG_CS5535_MFGPT, the driver does not link right:
drivers/watchdog/built-in.o: In function `geodewdt_probe':
geodewdt.c:(.init.text+0xca3): undefined reference to `cs5535_mfgpt_alloc_timer'
geodewdt.c:(.init.text+0xcd4): undefined reference to `cs5535_mfgpt_write'
geodewdt.c:(.init.text+0xcef): undefined reference to `cs5535_mfgpt_toggle_event'
This adds back the dependency on this base driver.
Fixes: da2a68b3eb47 ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The wm831x watchdog driver can now be built without the wm831x mfd
driver, which results in a link error:
(.text+0x1a95c): undefined reference to `wm831x_set_bits'
(.text+0x1a95c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `wm831x_set_bits'
(.text+0x1a968): undefined reference to `wm831x_reg_lock'
(.text+0x1a968): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `wm831x_reg_lock'
(.text+0x1a9dc): undefined reference to `wm831x_reg_unlock'
(.text+0x1a9dc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `wm831x_reg_unlock'
This adds back the dependency that was removed. We can still build test
this driver on all architectures by enabling the MFD driver for it first.
Fixes: da2a68b3eb47 ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix typos and add the following to the scripts/spelling.txt:
partiton||partition
Link: http://lkml.kernel.org/r/1481573103-11329-7-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Functions marked static inline might not be inlined so a driver-specific
prefix for function name helps when looking through call backtrace.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Syscon is used not only on Exynos5 SoCs but also on Exynos3250,
Exynos4412 and ARMv8 versions (Exynos5433, Exynos7).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Replace the 'debug' module parameter and pr_info() with proper device
dynamic debug calls because this is the preferred and flexible way of
enabling debugging printks.
Also remove some obvious debug printks.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. However the interrupt itself was not cleared thus on
first hit, the system enters infinite interrupt handling loop.
On Odroid U3 (Exynos4412), when booted with s3c2410_wdt.soft_noboot=1
argument the console is flooded:
# killall -9 watchdog
[ 60.523760] s3c2410-wdt 10060000.watchdog: watchdog timer expired (irq)
[ 60.536744] s3c2410-wdt 10060000.watchdog: watchdog timer expired (irq)
Fix this by writing something to the WTCLRINT register to clear the
interrupt. The register WTCLRINT however appeared in S3C6410 so a new
watchdog quirk and flavor are needed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The CONFIG prefix from defines in the s3c2410_wdt.c might suggest that
these constants come from Kconfig.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
It occurred to me that the panic pretimeout governor will stall the
softdog, because it is purely software which simply breaks when the
kernel panics. Testing governors with the softdog on the other hand is
really useful, so make this feature a compile time option which nees to
be enabled explicitly. This also removes the overhead if pretimeout
support is not used because it will now be compiled away (saving ~10% on
ARM32).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch adds watchdog controller driver for ZTE's zx2967 family.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
When resuming for the deepest state on sama5d2, it is necessary to restore
MR as the registers are lost.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
.config is used to cache a part of WDT_MR at probe time and is not used
afterwards. Instead of doing that, actually cache MR and avoid reading it
every time it is modified.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Cleanup this driver and convert it to use the watchdog framework API.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
[groeck: Dropped initialization of static variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Cleanup this driver and remove the 200ms heartbeat timer. The core now
has the ability to handle the heartbeat.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
[groeck: Dropped 0-initialization of static variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Without this dependency, platforms not supporting PCI (such as m68k)
report the following build warning when building allmodconfig
or allyesconfig.
drivers/watchdog/rdc321x_wdt.c: In function 'rdc321x_wdt_ioctl':
./arch/m68k/include/asm/uaccess_mm.h:61:1: warning:
'value' may be used uninitialized in this function
Fixes: f4c3de659054 ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This add support for the Cortina systems Gemini (SL3516)
SoC watchdog.
I have tried to use all the right new kernel interfaces
and tested with busybox' "watchdog" command both to kick
and get timeouts and reboots.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Declare watchdog_ops structures as const as they are only stored in the
ops field of a watchdog_device structure. This field is of type const, so
watchdog_ops structures having this property can be made const too.
Done using Coccinelle:
@r disable optional_qualifier@
identifier x;
position p;
@@
static struct watchdog_ops x@p={...};
@ok@
struct watchdog_device w;
identifier r.x;
position p;
@@
w.ops=&x@p;
@bad@
position p != {r.p,ok.p};
identifier r.x;
@@
x@p
@depends on !bad disable optional_qualifier@
identifier r.x;
@@
+const
struct watchdog_ops x;
File size details before and after patching.
First line of every .o file shows the file size before patching
and second line shows the size after patching.
text data bss dec hex filename
1340 544 0 1884 75c drivers/watchdog/bcm_kona_wdt.o
1436 440 0 1876 754 drivers/watchdog/bcm_kona_wdt.o
1176 544 4 1724 6bc drivers/watchdog/digicolor_wdt.o
1272 440 4 1716 6b4 drivers/watchdog/digicolor_wdt.o
925 580 89 1594 63a drivers/watchdog/ep93xx_wdt.o
1021 476 89 1586 632 drivers/watchdog/ep93xx_wdt.o
4932 288 17 5237 1475 drivers/watchdog/s3c2410_wdt.o
5028 192 17 5237 1475 drivers/watchdog/s3c2410_wdt.o
1977 292 1 2270 8de drivers/watchdog/sama5d4_wdt.o
2073 196 1 2270 8de drivers/watchdog/sama5d4_wdt.o
1375 484 1 1860 744 drivers/watchdog/sirfsoc_wdt.o
1471 380 1 1852 73c drivers/watchdog/sirfsoc_wdt.o
Size remains the same for the files drivers/watchdog/diag288_wdt.o
drivers/watchdog/asm9260_wdt.o and drivers/watchdog/atlas7_wdt.o
The following .o files did not compile:
drivers/watchdog/sun4v_wdt.o, drivers/watchdog/sbsa_gwdt.o,
drivers/watchdog/rt2880_wdt.o, drivers/watchdog/booke_wdt.o
drivers/watchdog/mt7621_wdt.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Many watchdog drivers explicitly stop the watchdog when unregistering it.
While it is unclear if this is actually needed (the whatdog should not be
running at that time if it can be stopped), introduce a helper to
explicitly stop the watchdog in the watchdog core when unregistering it.
This helps reducing driver code size while retaining functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the watchdog_register_device
call with the devm_watchdog_register_device call. In addition, the
ebc_c384_wdt_remove function has been removed as no longer necessary due
to the use of the relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Use devm_watchdog_register_driver() to register watchdog device
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'val = e; return val;' with 'return e;'
- Replace 'if (e) return e; return 0;' with 'return e;'
- Drop assignments to otherwise unused variables
- Drop unused variables
- Drop remove function
- Drop dev_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'val = e; return val;' with 'return e;'
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop dev_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'goto l; ... l: return e;' with 'return e;'
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'goto l; ... l: return e;' with 'return e;'
- Replace 'val = e; return val;' with 'return e;'
- Drop assignments to otherwise unused variables
- Replace 'if (e) { return expr; }' with 'if (e) return expr;'
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
improvements
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
Other improvements as listed below.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Drop assignments to otherwise unused variables
- Replace of_iomap() with platform_get_resource() followed by
devm_ioremap_resource()
- Replace &pdev->dev with dev if 'struct device *dev' is a declared
variable
- Use devm_watchdog_register_driver() to register watchdog device
- Replace shutdown function with call to watchdog_stop_on_reboot()
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
improvements
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
Other improvements as listed below.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'goto l; ... l: return e;' with 'return e;'
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop unnecessary mutex_destroy() on allocated data
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Johannes Thumshirn <morbidrsa@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'goto l; ... l: return e;' with 'return e;'
- Replace 'val = e; return val;' with 'return e;'
- Drop assignments to otherwise unused variables
- Replace 'if (e) { return expr; }' with 'if (e) return expr;'
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
improvements
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
Other improvements as listed below.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace 'goto l; ... l: return e;' with 'return e;'
- Replace 'val = e; return val;' with 'return e;'
- Drop assignments to otherwise unused variables
- Replace 'if (e) { return expr; }' with 'if (e) return expr;'
- Drop remove function
- Replace of_iomap() with platform_get_resource() followed by
devm_ioremap_resource()
- Drop platform_set_drvdata()
- Replace &pdev->dev with dev if 'struct device *dev' is a declared
variable
- Use devm_watchdog_register_driver() to register watchdog device
- Replace shutdown function with call to watchdog_stop_on_reboot()
Acked-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
watchdog_stop_on_reboot
The shutdown function calls the stop function.
Call watchdog_stop_on_reboot() from probe instead.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Replace shutdown function with call to watchdog_stop_on_reboot()
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
improvements
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
Other improvements as listed below.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
- Replace shutdown function with call to watchdog_stop_on_reboot()
Cc: Carlo Caione <carlo@caione.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
improvements
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
Other improvements as listed below.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
- Replace shutdown function with call to watchdog_stop_on_reboot()
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use device managed functions to simplify error handling, reduce
source code size, improve readability, and reduce the likelyhood of bugs.
The conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts used
to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Drop assignments to otherwise unused variables
- Drop remove function
- Drop platform_set_drvdata()
- Use devm_watchdog_register_driver() to register watchdog device
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use a local dev variable instead of dereferencing pdev->dev several
times in the probe function to make the code easier to read.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Map resources using devm_ioremap_resource() to simplify error handling.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Enabling the clock before accessing chip registers and disabling it
afterwards does not really make sense and only adds complexity to
the driver. In addition to that, a comment int the driver suggests
that it does not serve a useful purpose either.
"The watchdog block is of course always clocked, the
clk_enable()/clk_disable() calls are mainly for performing reference
counting higher up in the clock hierarchy."
Just keep the clock enabled instead.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Checking if there is no error followed by a goto if there is one is
confusing. Reverse the logic.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
