| Age | Commit message (Collapse) | Author |
|---|
|
add support for ds2430, 1 page, 256bit (32bytes) eeprom
(family 0x14).
Tests done:
32 bytes dump:
x@y:~# hexdump -C -n 32 /sys/bus/w1/devices/14-00000158556e/eeprom
00000000 39 39 0a 00 00 36 0a ff ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
00000020
34 bytes dump: 32 only displayed
x@y:~# hexdump -C -n 34 /sys/bus/w1/devices/14-00000158556e/eeprom
00000000 39 39 0a 00 00 36 0a ff ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
00000020
pattern write:
x@y:~# echo 123456789 > /sys/bus/w1/devices/14-00000158556e/eeprom
x@y:~# hexdump -C -n 54 /sys/bus/w1/devices/14-00000158556e/eeprom
00000000 31 32 33 34 35 36 37 38 39 0a ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
00000020
specific address 1-byte write
x@y:~# dd if=/dev/zero of=/sys/bus/w1/devices/14-00000158556e/eeprom \
count=1 bs=1 seek=4
1+0 records in
1+0 records out
x@y:~# hexdump -C -n 54 /sys/bus/w1/devices/14-00000158556e/eeprom
00000000 31 32 33 34 00 36 37 38 39 0a ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
00000020
writing binary block
x@y:~# cat dump-128bytes.bin > /sys/bus/w1/devices/14-00000158556e/eeprom
cat: write error: File too large
x@y:~# cat dump-32bytes.bin > /sys/bus/w1/devices/14-00000158556e/eeprom
x@y:~# hexdump -C -n 54 /sys/bus/w1/devices/14-00000158556e/eeprom
00000000 10 0b 5b ff ff ff ff ff ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 40
00000020
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Link: https://lore.kernel.org/r/20191019204015.61474-1-angelo.dureghello@timesys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a 1-Wire slave driver to support DS250x EPROM deivces. This
slave driver attaches the devices to the NVMEM subsystem for
an easy in-kernel usage.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Link: https://lore.kernel.org/r/20190831082623.15627-3-tbogendoerfer@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
companion
This patch removes the w1 slave driver that used to register the w1 family
and instanciate a platform device at runtime. The code now lives in the
supply driver instead to avoid that level of indirection.
The old device name "ds2760-battery.0" is preserved, so userspace
applications can access the same virtual device nodes as before.
Note that because the w1 core does not currently have a framework for
suspend/resume, the driver now registers a PM notifier callback.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem patches
for 4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
All of these have been in linux-next for quite a while with no
reported issues"
* tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
VME: Return -EBUSY when DMA list in use
w1: keep balance of mutex locks and refcnts
MAINTAINERS: Update VME subsystem tree.
nvmem: sunxi-sid: add support for A64/H5's SID controller
nvmem: imx-ocotp: Update module description
nvmem: imx-ocotp: Enable i.MX7D OTP write support
nvmem: imx-ocotp: Add i.MX7D timing write clock setup support
nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function
nvmem: imx-ocotp: Add support for banked OTP addressing
nvmem: imx-ocotp: Pass parameters via a struct
nvmem: imx-ocotp: Restrict OTP write to IMX6 processors
nvmem: uniphier: add UniPhier eFuse driver
dt-bindings: nvmem: add description for UniPhier eFuse
nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset
nvmem: qfprom: fix different address space warnings of sparse
nvmem: mtk-efuse: fix different address space warnings of sparse
nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it
nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it
thunderbolt: tb: fix use after free in tb_activate_pcie_devices
MAINTAINERS: Add git tree for Thunderbolt development
...
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This subpatch adds a driver for the DS28E17 Onewire to I2C master bridge.
Signed-off-by: Jan Kandziora <jjj@gmx.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset changes from Sebastian Reichel:
"New chip/feature support:
- bq27xxx: support updating battery config from DT
- bq24190: support loading battery charge info from DT
- LTC2941: add LTC2942/LTC2944 support
- max17042: add ACPI support
- max1721x: new driver
Misc:
- Move bq27xxx w1 driver from w1 into power-supply subsystem
- Introduce power_supply_set_input_current_limit_from_supplier
- constify stuff
- some minor fixes"
* tag 'for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (39 commits)
power: supply: bq27xxx: enable writing capacity values for bq27421
power: supply: bq24190_charger: Get input_current_limit from our supplier
power: supply: bq24190_charger: Export 5V boost converter as regulator
power: supply: bq24190_charger: Add power_supply_battery_info support
power: supply: bq24190_charger: Add property system-minimum-microvolt
power: supply: bq24190_charger: Enable devicetree config
dt-bindings: power: supply: Add docs for TI BQ24190 battery charger
power: supply: bq27xxx: Remove duplicate chip data arrays
power: supply: bq27xxx: Enable data memory update for certain chips
power: supply: bq27xxx: Add chip IDs for previously shadowed chips
power: supply: bq27xxx: Create single chip data table
power: supply: bq24190_charger: Add ti,bq24192i to devicetree table
power: supply: bq24190_charger: Add input_current_limit property
power: supply: Add power_supply_set_input_current_limit_from_supplier helper
power: supply: max17042_battery: Fix compiler warning
power: supply: core: Delete two error messages for a failed memory allocation in power_supply_check_supplies()
power: supply: make device_attribute const
power: supply: max17042_battery: Fix ACPI interrupt issues
power: supply: max17042_battery: Add support for ACPI enumeration
power: supply: lp8788: Make several arrays static const * const
...
|
|
Add a one wire driver for the DS28E05 one wire slave chip. This chip
requires OverDrive support to talk to it.
Signed-off-by: Andrew Worsley <amworsley@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The HDQ interface driver should be in this folder just like the I2C
interface driver. Move this driver out of drivers/w1/slave and into
drivers/power/supply.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
Detailed information about support and provided sysfs files
in my next commit which creates a documentation file:
Documentation/w1/slaves/w1_ds2438
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds a driver for a DS2405 1-wire single-channel addressable switch.
The DS2405 can also work as a single-channel binary remote sensor.
This driver supports two attributes: "state" and "output" which are the
same attribute names as supported by existing DS2406, DS2408 and DS2413
drivers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some preliminary work at making use of this driver led me to implement
CRC-16 checks on read and write to deal with the occasional glitchiness of
the 1-Wire bus. The revised driver (attached) returns an I/O error if the
CRC check fails. When reading the chip's state, either you get a valid
indication or you get an I/O error. When changing its state, either the
change is successful or an I/O error is returned.
Signed-off-by: Scott Alfter <scott@alfter.us>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Also fixes some whitespace inconsistency in Kconfig and w1_family.h when
DS2408 chip support was added.
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Markus Franke <franm@hrz.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Renata Sayakhova <rsayakhova@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for the Maxim/Dallas DS2780 Stand-Alone Fuel Gauge IC.
It was suggested to combine this functionality with the current ds2782
driver. Unfortunately, I'm unable to commit the time to refactoring this
driver to that extent and I don't have a platform with the ds2782 part to
validate that there are no regression issues by adding this functionality.
[akpm@linux-foundation.org: use min_t()]
Signed-off-by: Clifton Barnes <cabarnes@indesign-llc.com>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This DS2408 w1 slave driver is not complete for all the features of the
chip, but its sufficient if you use it as a simple IO expander.
[randy.dunlap@oracle.com: fix w1_ds2408.c printk formats]
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Cc: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is a 1-wire/w1 DS2423 slave driver for reading the values from all 4
counters available DS2423 devices by using standard w1_slave file. In
ds2423 the counters are tied to ram pages 12-15 in and each of those
ram-pages. Each of these counter values (and asoociated ram page values)
are represented as a own line in w1_slave file. Driver has been tested on
mips and x86.
usage example:
cat /sys/bus/w1/devices/1d-00000009b964/w1_slave
00 02 00 00 00 00 00 00 00 6d 38 00 ff ff 00 00 fe ff 00 00 ff ff 00 00 ff
ff 00 00 ff ff 00 00 ff ff 00 00 ff ff 00 00 ff ff crc=YES c=2
00 02 00 00 00 00 00 00 00 e0 1f 00 ff ff 00 00 ff ff 00 00 ff ff 00 00 ff
ff 00 00 ff ff 00 00 ff ff 00 00 ff ff 00 00 ff ff crc=YES c=2
00 5a 0e 5f 18 00 00 00 00 0b 28 00 ff ff 00 00 ff ff 00 00 ff ff 00 00 ff
ff 00 00 ff ff 00 00 ff ff 00 00 ff ff 00 00 ff ff crc=YES c=408882778
00 05 00 00 00 00 00 00 00 8d 39 ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff crc=YES c=5
Patch includes also the documentation.
[randy.dunlap@oracle.com: fix ds2423 build, needs to select CRC16]
Signed-off-by: Mika Laitio <lamikr@pilppa.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Provide the BQ27000 slave interface driver.
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is W1 slave for ds2760 chip, found inside almost every HP iPaq and
HTC PDAs/phones.
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
CONFIG_W1_SLAVE_DS2433_CRC can be used directly, there's no reason for the
indirection of defining a different variable in the Makefile.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
into 'w1/slaves'
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
