| Age | Commit message (Collapse) | Author |
|---|
|
Replication logic for an overlay depends on the color mode in which it is
configured and the video port width of the manager it is connected to.
video port width now held in dss_lcd_mgr_config in the manager's private
data in APPLY. Use this instead of referring to the omap_dss_device connected to
the manager.
Replication is enabled in the case of TV manager, the video_port_width is set to
a default value of 24 for TV manager.
Make the replication checking an overlay function since it's more of an overlay
characteristic than a display characteristic.
Signed-off-by: Archit Taneja <archit@ti.com>
|
|
The support for LCD3 manager has been added into the manager module. LCD3 panel
has registers as DISPC_CONTROL3 and DISPC_CONFIG3 just like those in LCD and
LCD2 panels. These registers control the Display Controller (DISPC) module for
LCD3 output. The three LCDs support Display Serial Interface (DSI), Remote Frame
Buffer Interface (RFBI) and Parallel CMOS Output Interface (DPI). These LCDs can
be connected through parallel output interface using DISPC and RFBI or DPI. For
serial interface DSS uses DSI.
The LCD3 panel, just like LCD and LCD2 panels, has a clock switch in DSS_CTRL
register which has been enabled. The clock switch chooses between DSS_CLK and
DPLL_DSI1_C_CLK1 as source for LCD3_CLK. New IRQs as DISPC_IRQ_VSYNC3,
DISPC_IRQ_FRAMEDONE3, DISPC_IRQ_ACBIAS_COUNT_STAT3 and DISPC_IRQ_SYNC_LOST3 have
been added specific to the new manager.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
We have two almost the same enums: omap_channel and
omap_dss_overlay_managers. omap_channel is used almost everywhere, and
omap_channel assigns explicit values to the enum values which are needed
for proper operation.
omap_dss_overlay_managers is only used in one place, so it's easy to
remove it, which is what this patch does.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
TILER is a block in OMAP4's DMM which lets DSS fetch frames in a rotated manner.
Physical memory can be mapped to a portion of OMAP's system address space called
TILER address space. The TILER address space is split into 8 views. Each view
represents a rotated or mirrored form of the mapped physical memory. When a
DISPC overlay's base address is programmed to one of these views, the TILER
fetches the pixels according to the orientation of the view. A view is further
split into 4 containers, each container holds elements of a particular size.
Rotation can be achieved at the granularity of elements in the container. For
more information on TILER, refer to the Memory Subsytem section in OMAP4 TRM.
Rotation type TILER has been added which is used to exploit the capabilities of
these 8 views for performing various rotations.
When fetching from addresses mapped to TILER space, the DISPC DMA can fetch
pixels in either 1D or 2D bursts. The fetch depends on which TILER container we
are accessing. Accessing 8, 16 and 32 bit sized containers requires 2D bursts,
and page mode sized containers require 1D bursts.
The DSS2 user is expected to provide the Tiler address of the view that it is
interested in. This is passed to the paddr and p_uv_addr parameters in
omap_overlay_info. It is also expected to provide the stride value based on the
view's orientation and container type, this should be passed to the screen_width
parameter of omap_overlay_info. In calc_tiler_rotation_offset screen_width is
used to calculate the required row_inc for DISPC. x_predecim and y_predecim are
also used to calculate row_inc and pix_inc thereby adding predecimation support
for TILER.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
In order to check the validity of overlay and manager info, there was a need to
use the omap_dss_device struct to get the panel resolution. The manager's
private data in APPLY now contains the manager timings. Hence, we don't need to
rely on the display resolution any more.
Pass the manager's timings in private data to dss_mgr_check(). Remove the need
to pass omap_dss_device structs in the functions which check for the validity
of overlay and manager parameters.
Signed-off-by: Archit Taneja <archit@ti.com>
|
|
The functions dss_ovl_simple_check() and dss_mgr_simple_check() are not
really part of the apply mechanism, and can be moved to overlay.c and
manager.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The functions dss_ovl_check, dss_mgr_check_zorder, dss_mgr_check in
apply.c are not really part of the apply mechanism, and can be moved to
overlay.c and manager.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
struct omap_overlayr contains info and info_dirty fields, both of which
should be internal to apply.c.
This patch moves those fields into ovl_priv data, and names them
user_info and user_info_dirty.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Overlays are currently enabled and disabled with a boolean in the struct
omap_overlay_info. The overlay info is set with ovl->set_overlay_info(),
and made into use with mgr->apply().
This doesn't work properly, as the enable/disable status may affect also
other overlays, for example when using fifo-merge. Thus the enabling and
disabling of the overlay needs to be done outside the normal overlay
configuration.
This patch achieves that by doing the following things:
1) Add function pointers to struct omap_overlay: enable(), disable() and
is_enabled(). These are used to do the obvious. The functions may block.
2) Move the "enabled" field from struct omap_overlay to ovl_priv_data.
3) Add a new route for settings to be applied to the HW, called
"extra_info". The status of the normal info and extra_info are tracked
separately.
The point here is to allow the normal info to be changed and
applied in non-blocking matter, whereas the extra_info can only be
changed when holding the mutex. This makes it possible to, for example,
set the overlay enable flag, apply it, and wait until the HW has taken
the flag into use.
This is not possible if the enable flag would be in the normal info, as
a new value for the flag could be set at any time from the users of
omapdss.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
DSS currently tries to check that the given overlay and overlay manager
settings are acceptable, but the code does not work quite properly.
Things may change between the check and the actual use of the settings.
Furthermore, the following patches will rewrite how settings are
configured and managed, and trying to keep the (broken) settings
checking working during the rewrite would be very difficult.
This patch removes the checking code, and a working version of checking
will be added back after the settings rewrite has been done.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
apply.c will handle the management of dispc in the future patches. This
patch moves overlay related functions to apply.c so that they will have
access to the private data and functions of apply.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Current way of handling overlay-manager links is a bit strange: each
manager has a static array, containing pointers to all the overlays
(even those used by other managers). The overlays contain a pointer to
the manager being used.
This patch makes the system a bit saner: each manager has a linked list
of overlays, and only the overlays linked to that manager are in the
list.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Overlays are stored in a linked list. There's no need for this list, as
an array would do just as fine.
This patch changes the code to use an array for overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
There's an unnecessary wrapper function, dss_ovl_wait_for_go(), which
does nothing else than call dss_mgr_wait_for_go_ovl(). The
dss_ovl_wait_for_go() function can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Some old example code has been left lying around. Remove the example
code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add zorder support on OMAP4, this feature allows deciding the visibility order
of the overlays based on the zorder value provided as an overlay info parameter
or a sysfs attribute of the overlay object.
Use the overlay cap OMAP_DSS_OVL_CAP_ZORDER to determine whether zorder is
supported for the overlay or not. Use dss feature FEAT_ALPHA_FREE_ZORDER
if the caps are not available.
Ensure that all overlays that are enabled and connected to the same manager
have different zorders. Swapping zorders of 2 enabled overlays currently
requires disabling one of the overlays.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add support for VIDEO3 pipeline on OMAP4:
- Add VIDEO3 pipeline information in dss_features and omapdss.h
- Add VIDEO3 pipeline register coefficients in dispc.h
- Create a new overlay structure corresponding to VIDEO3.
- Make changes in dispc.c for VIDEO3
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Use strtobool and kstrto* functions when parsing sysfs inputs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add OMAP_DSS_OVL_CAP_GLOBAL_ALPHA and OMAP_DSS_OVL_CAP_PRE_MULT_ALPHA to
overlay capabilities. Use these instead of FEAT_GLOBAL_ALPHA,
FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA in code.
Remove FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA which are no
longer used. FEAT_GLOBAL_ALPHA is still used to decide if the HW has
global alpha register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
|
|
Add support to define overlay capabilities into dss_features. The
features are set to overlay->caps at initialization time.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
|
|
Remove support for non-DISPC overlays and overlay managers.
The support to possibly have non-DISPC overlays and managers was made to
make it possible to use CPU and/or sDMA to update RFBI or DSI command
mode displays. It is ok to remove the support, because:
- No one has used the feature.
- Display update without DISPC is very slow, so it is debatable if the
update would even be usable.
- Removal cleans up code.
- If such a feature is needed later, it is better implemented outside
omapdss driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
|
|
Currently when changing the manager of an overlay, set_manager() directly
calls dispc to set the overlay's destination.
Change this to be more in line with other overlay configurations, and
this will also remove the need to have dispc clocks enabled when calling
set_manager().
A new field is added to overlay struct, "manager_changed". This is
similar to "display_changed" field in manager struct, and is used to
inform apply that the manager has changed and thus write to the
registers is needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Use PM runtime and HWMOD support to handle enabling and disabling of DSS
modules.
Each DSS module will have get and put functions which can be used to
enable and disable that module. The functions use pm_runtime and hwmod
opt-clocks to enable the hardware.
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
OMAP2 doesn't have CPR, PRELOAD nor FIR_COEF_V registers. Add new
feature definitions for those, and check the feature before accessing
those registers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Convert simple/strict_strto* functions to kstrto* functions. Only simple
cases are converted.
simple_strto* uses are still left to places where it is used to parse
numbers from a list of numbers. These need some other solution than
kstrto*.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The sleep workaround for the problem described in the comment doesn't
really work. This patch removes the workaround, and improves the comment
about the bug, and proposes an userspace workaround.
omap_dss_set_manager() is called 6 times when loading omapdss and
omapfb, which means that 40ms * 6 = 240ms was spent sleeping when
booting up.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Adding display type HDMI in dss_features, overlay and the manager so that
HDMI type of display will be recognized.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
enum dss_clock structure is replaced with generic names that
could be used across OMAP2420, 2430, 3xxx, 44xx platforms.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
overlay manager.
A panel connects to one of the overlay managers of DSS through some interface block.
On OMAP4, specifying the type of the display is not sufficient to conclude which manager
the panel should be connected to.
Hence, a new member 'channel' is introduced in omap_dss_device structure to determine
which manager the panel uses. The dss_recheck_connections() called in dss_driver_probe()
uses this channel parameter to set the correct manager to the corresponding omap_dss_device.
The channel parameter is used only once to ensure the correct managers are set for each
panel. The parameter dssdev->manager->id will take care of ensuring that the panel and
then the interface driver configures the correct DISPC channel.
Also, add a new Overlay Manager in manager.c, make other changes needed for LCD2 channel.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Enable dss to process color formats with pre-mulitplied alpha.
With this we can have alpha values defined for each pixel
and hence can have different blending values for each pixel.
sysfs entry has been created for this and pre-multiplied alpha
support is turned off by default.
Signed-off-by: Sudeep Basavaraj <sudeep.basavaraj@ti.com>
Signed-off-by: Rajkumar N <rajkumar.nagarajan@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Calls init functions of dss_features during dss_probe, and the following
features are made omapxxxx independent:
- number of managers, overlays
- supported color modes for each overlay
- supported displays for each manager
- global aplha, and restriction of global alpha for video1 pipeline
- The register field ranges : FIRHINC, FIRVINC, FIFOHIGHTHRESHOLD
FIFOLOWTHRESHOLD and FIFOSIZE
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
The function overlay_manager_store currently fails if the sysfs input is a
prefix string of an existing overlay manager name. This occurs because strncmp
compares the two strings only till the length of the input sysfs string. So a
sysfs input "lcd" will match manager name "lcd2" which is incorrect behavior.
The use of sysfs_streq here will prevent this false positive match to occur.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Move get_resolution() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Add more core files to DSS2.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
