| Age | Commit message (Collapse) | Author |
|---|
|
When we try to get an MSI cookie for a VFIO device, that can fail if
CONFIG_IOMMU_DMA is not set. In this case iommu_get_msi_cookie() returns
-ENODEV, and that should not be fatal.
Ignore that case and proceed with the initialisation.
This fixes VFIO with a platform device on the Calxeda Midway (no MSIs).
Fixes: f6810c15cf973f ("iommu/arm-smmu: Clean up early-probing workarounds")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Older versions of skiboot only provide a single value in the device
tree property "ibm,mmio-atsd", even when multiple Address Translation
Shoot Down (ATSD) registers are present. This prevents NVLink2 devices
(other than the first) from being used with vfio-pci because vfio-pci
expects to be able to assign a dedicated ATSD register to each NVLink2
device.
However, ATSD registers can be shared among devices. This change
allows vfio-pci to fall back to sharing the register at index 0 if
necessary.
Fixes: 7f92891778df ("vfio_pci: Add NVIDIA GV100GL [Tesla V100 SXM2] subdriver")
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
v5.7/vfio/next
|
|
The cleanup is getting a tad long.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
It currently results in messages like:
"vfio-pci 0000:03:00.0: vfio_pci: ..."
Which is quite a bit redundant.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
With the VF Token interface we can now expect that a vfio userspace
driver must be in collaboration with the PF driver, an unwitting
userspace driver will not be able to get past the GET_DEVICE_FD step
in accessing the device. We can now move on to actually allowing
SR-IOV to be enabled by vfio-pci on the PF. Support for this is not
enabled by default in this commit, but it does provide a module option
for this to be enabled (enable_sriov=1). Enabling VFs is rather
straightforward, except we don't want to risk that a VF might get
autoprobed and bound to other drivers, so a bus notifier is used to
"capture" VFs to vfio-pci using the driver_override support. We
assume any later action to bind the device to other drivers is
condoned by the system admin and allow it with a log warning.
vfio-pci will disable SR-IOV on a PF before releasing the device,
allowing a VF driver to be assured other drivers cannot take over the
PF and that any other userspace driver must know the shared VF token.
This support also does not provide a mechanism for the PF userspace
driver itself to manipulate SR-IOV through the vfio API. With this
patch SR-IOV can only be enabled via the host sysfs interface and the
PF driver user cannot create or remove VFs.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The VFIO_DEVICE_FEATURE ioctl is meant to be a general purpose, device
agnostic ioctl for setting, retrieving, and probing device features.
This implementation provides a 16-bit field for specifying a feature
index, where the data porition of the ioctl is determined by the
semantics for the given feature. Additional flag bits indicate the
direction and nature of the operation; SET indicates user data is
provided into the device feature, GET indicates the device feature is
written out into user data. The PROBE flag augments determining
whether the given feature is supported, and if provided, whether the
given operation on the feature is supported.
The first user of this ioctl is for setting the vfio-pci VF token,
where the user provides a shared secret key (UUID) on a SR-IOV PF
device, which users must provide when opening associated VF devices.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
If we enable SR-IOV on a vfio-pci owned PF, the resulting VFs are not
fully isolated from the PF. The PF can always cause a denial of service
to the VF, even if by simply resetting itself. The degree to which a PF
can access the data passed through a VF or interfere with its operation
is dependent on a given SR-IOV implementation. Therefore we want to
avoid a scenario where an existing vfio-pci based userspace driver might
assume the PF driver is trusted, for example assigning a PF to one VM
and VF to another with some expectation of isolation. IOMMU grouping
could be a solution to this, but imposes an unnecessarily strong
relationship between PF and VF drivers if they need to operate with the
same IOMMU context. Instead we introduce a "VF token", which is
essentially just a shared secret between PF and VF drivers, implemented
as a UUID.
The VF token can be set by a vfio-pci based PF driver and must be known
by the vfio-pci based VF driver in order to gain access to the device.
This allows the degree to which this VF token is considered secret to be
determined by the applications and environment. For example a VM might
generate a random UUID known only internally to the hypervisor while a
userspace networking appliance might use a shared, or even well know,
UUID among the application drivers.
To incorporate this VF token, the VFIO_GROUP_GET_DEVICE_FD interface is
extended to accept key=value pairs in addition to the device name. This
allows us to most easily deny user access to the device without risk
that existing userspace drivers assume region offsets, IRQs, and other
device features, leading to more elaborate error paths. The format of
these options are expected to take the form:
"$DEVICE_NAME $OPTION1=$VALUE1 $OPTION2=$VALUE2"
Where the device name is always provided first for compatibility and
additional options are specified in a space separated list. The
relation between and requirements for the additional options will be
vfio bus driver dependent, however unknown or unused option within this
schema should return error. This allow for future use of unknown
options as well as a positive indication to the user that an option is
used.
An example VF token option would take this form:
"0000:03:00.0 vf_token=2ab74924-c335-45f4-9b16-8569e5b08258"
When accessing a VF where the PF is making use of vfio-pci, the user
MUST provide the current vf_token. When accessing a PF, the user MUST
provide the current vf_token IF there are active VF users or MAY provide
a vf_token in order to set the current VF token when no VF users are
active. The former requirement assures VF users that an unassociated
driver cannot usurp the PF device. These semantics also imply that a
VF token MUST be set by a PF driver before VF drivers can access their
device, the default token is random and mechanisms to read the token are
not provided in order to protect the VF token of previous users. Use of
the vf_token option outside of these cases will return an error, as
discussed above.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
This currently serves the same purpose as the default implementation
but will be expanded for additional functionality.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Allow bus drivers to provide their own callback to match a device to
the user provided string.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
vfio_group_pin_pages() and vfio_group_unpin_pages() are introduced to
avoid inefficient search/check/ref/deref opertions associated with VFIO
group as those in each calling into vfio_pin_pages() and
vfio_unpin_pages().
VFIO group is taken as arg directly. The callers combine
search/check/ref/deref operations associated with VFIO group by calling
vfio_group_get_external_user()/vfio_group_get_external_user_from_dev()
beforehand, and vfio_group_put_external_user() afterwards.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
vfio_dma_rw will read/write a range of user space memory pointed to by
IOVA into/from a kernel buffer without enforcing pinning the user space
memory.
TODO: mark the IOVAs to user space memory dirty if they are written in
vfio_dma_rw().
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
external user calls vfio_group_get_external_user_from_dev() with a device
pointer to get the VFIO group associated with this device.
The VFIO group is checked to be vialbe and have IOMMU set. Then
container user counter is increased and VFIO group reference is hold
to prevent the VFIO group from disposal before external user exits.
when the external user finishes using of the VFIO group, it calls
vfio_group_put_external_user() to dereference the VFIO group and the
container user counter.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Since commit 7723f4c5ecdb ("driver core: platform: Add an error
message to platform_get_irq*()"), platform_get_irq() calls dev_err()
on an error. As we enumerate all interrupts until platform_get_irq()
fails, we now systematically get a message such as:
"vfio-platform fff51000.ethernet: IRQ index 3 not found" which is
a false positive.
Let's use platform_get_irq_optional() instead.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Cc: stable@vger.kernel.org # v5.3+
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Pull VFIO updates from Alex Williamson:
- Fix nvlink error path (Alexey Kardashevskiy)
- Update nvlink and spapr to use mmgrab() (Julia Lawall)
- Update static declaration (Ben Dooks)
- Annotate __iomem to fix sparse warnings (Ben Dooks)
* tag 'vfio-v5.6-rc1' of git://github.com/awilliam/linux-vfio:
vfio: platform: fix __iomem in vfio_platform_amdxgbe.c
vfio/mdev: make create attribute static
vfio/spapr_tce: use mmgrab
vfio: vfio_pci_nvlink2: use mmgrab
vfio/spapr/nvlink2: Skip unpinning pages on error exit
|
|
In order to provide a clearer, more symmetric API for pinning and
unpinning DMA pages. This way, pin_user_pages*() calls match up with
unpin_user_pages*() calls, and the API is a lot closer to being
self-explanatory.
Link: http://lkml.kernel.org/r/20200107224558.2362728-23-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
1. Change vfio from get_user_pages_remote(), to
pin_user_pages_remote().
2. Because all FOLL_PIN-acquired pages must be released via
put_user_page(), also convert the put_page() call over to
put_user_pages_dirty_lock().
Note that this effectively changes the code's behavior in
vfio_iommu_type1.c: put_pfn(): it now ultimately calls
set_page_dirty_lock(), instead of set_page_dirty(). This is probably
more accurate.
As Christoph Hellwig put it, "set_page_dirty() is only safe if we are
dealing with a file backed page where we have reference on the inode it
hangs off." [1]
[1] https://lore.kernel.org/r/20190723153640.GB720@lst.de
Link: http://lkml.kernel.org/r/20200107224558.2362728-20-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update VFIO to take advantage of the recently loosened restriction on
FOLL_LONGTERM with get_user_pages_remote(). Also, now it is possible to
fix a bug: the VFIO caller is logically a FOLL_LONGTERM user, but it
wasn't setting FOLL_LONGTERM.
Also, remove an unnessary pair of calls that were releasing and
reacquiring the mmap_sem. There is no need to avoid holding mmap_sem
just in order to call page_to_pfn().
Also, now that the the DAX check ("if a VMA is DAX, don't allow long
term pinning") is in the internals of get_user_pages_remote() and
__gup_longterm_locked(), there's no need for it at the VFIO call site. So
remove it.
Link: http://lkml.kernel.org/r/20200107224558.2362728-8-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Suggested-by: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The ioaddr should have __iomem marker on it, so add that to fix
the following sparse warnings:
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:33:44: warning: incorrect type in argument 2 (different address spaces)
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:33:44: expected void volatile [noderef] <asn:2> *addr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:33:44: got void *
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:34:33: warning: incorrect type in argument 1 (different address spaces)
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:34:33: expected void const volatile [noderef] <asn:2> *addr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:34:33: got void *
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:44:44: warning: incorrect type in argument 2 (different address spaces)
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:44:44: expected void volatile [noderef] <asn:2> *addr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:44:44: got void *
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:45:33: warning: incorrect type in argument 2 (different address spaces)
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:45:33: expected void volatile [noderef] <asn:2> *addr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:45:33: got void *
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:69:41: warning: incorrect type in argument 1 (different address spaces)
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:69:41: expected void *ioaddr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:69:41: got void [noderef] <asn:2> *ioaddr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:71:30: warning: incorrect type in argument 1 (different address spaces)
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:71:30: expected void *ioaddr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:71:30: got void [noderef] <asn:2> *ioaddr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:76:49: warning: incorrect type in argument 1 (different address spaces)
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:76:49: expected void *ioaddr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:76:49: got void [noderef] <asn:2> *ioaddr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:85:37: warning: incorrect type in argument 1 (different address spaces)
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:85:37: expected void *ioaddr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:85:37: got void [noderef] <asn:2> *ioaddr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:87:30: warning: incorrect type in argument 1 (different address spaces)
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:87:30: expected void *ioaddr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:87:30: got void [noderef] <asn:2> *ioaddr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:90:30: warning: incorrect type in argument 1 (different address spaces)
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:90:30: expected void *ioaddr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:90:30: got void [noderef] <asn:2> *ioaddr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:93:30: warning: incorrect type in argument 1 (different address spaces)
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:93:30: expected void *ioaddr
drivers/vfio/platform/reset/vfio_platform_amdxgbe.c:93:30: got void [noderef] <asn:2> *ioaddr
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Acked-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The create attribute is not exported, so make it
static to avoid the following sparse warning:
drivers/vfio/mdev/mdev_sysfs.c:77:1: warning: symbol 'mdev_type_attr_create' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Mmgrab was introduced in commit f1f1007644ff ("mm: add new mmgrab()
helper") and most of the kernel was updated to use it. Update a
remaining file.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@ expression e; @@
- atomic_inc(&e->mm_count);
+ mmgrab(e);
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Mmgrab was introduced in commit f1f1007644ff ("mm: add new mmgrab()
helper") and most of the kernel was updated to use it. Update a
remaining file.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@ expression e; @@
- atomic_inc(&e->mm_count);
+ mmgrab(e);
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The nvlink2 subdriver for IBM Witherspoon machines preregisters
GPU memory in the IOMMI API so KVM TCE code can map this memory
for DMA as well. This is done by mm_iommu_newdev() called from
vfio_pci_nvgpu_regops::mmap.
In an unlikely event of failure the data->mem remains NULL and
since mm_iommu_put() (which unregisters the region and unpins memory
if that was regular memory) does not expect mem=NULL, it should not be
called.
This adds a check to only call mm_iommu_put() for a valid data->mem.
Fixes: 7f92891778df ("vfio_pci: Add NVIDIA GV100GL [Tesla V100 SXM2] subdriver")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pull VFIO updates from Alex Williamson:
- Remove hugepage checks for reserved pfns (Ben Luo)
- Fix irq-bypass unregister ordering (Jiang Yi)
* tag 'vfio-v5.5-rc1' of git://github.com/awilliam/linux-vfio:
vfio/pci: call irq_bypass_unregister_producer() before freeing irq
vfio/type1: remove hugepage checks in is_invalid_reserved_pfn()
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
|
|
Since irq_bypass_register_producer() is called after request_irq(), we
should do tear-down in reverse order: irq_bypass_unregister_producer()
then free_irq().
Specifically free_irq() may release resources required by the
irqbypass del_producer() callback. Notably an example provided by
Marc Zyngier on arm64 with GICv4 that he indicates has the potential
to wedge the hardware:
free_irq(irq)
__free_irq(irq)
irq_domain_deactivate_irq(irq)
its_irq_domain_deactivate()
[unmap the VLPI from the ITS]
kvm_arch_irq_bypass_del_producer(cons, prod)
kvm_vgic_v4_unset_forwarding(kvm, irq, ...)
its_unmap_vlpi(irq)
[Unmap the VLPI from the ITS (again), remap the original LPI]
Signed-off-by: Jiang Yi <giangyi@amazon.com>
Cc: stable@vger.kernel.org # v4.4+
Fixes: 6d7425f109d26 ("vfio: Register/unregister irq_bypass_producer")
Link: https://lore.kernel.org/kvm/20191127164910.15888-1-giangyi@amazon.com
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
[aw: commit log]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
|
|
Each of these drivers has a copy of the same trivial helper function to
convert the pointer argument and then call the native ioctl handler.
We now have a generic implementation of that, so use it.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Currently, no hugepage split code can transfer the reserved bit
from head to tail during the split, so checking the head can't make
a difference in a racing condition with hugepage spliting.
The buddy wouldn't allow a driver to allocate an hugepage if any
subpage is reserved in the e820 map at boot, if any driver sets the
reserved bit of head page before mapping the hugepage in userland,
it needs to set the reserved bit in all subpages to be safe.
Signed-off-by: Ben Luo <luoben@linux.alibaba.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
After enabling CONFIG_IOMMU_DMA on X86 a new warning appears when
compiling vfio:
drivers/vfio/vfio_iommu_type1.c: In function ‘vfio_iommu_type1_attach_group’:
drivers/vfio/vfio_iommu_type1.c:1827:7: warning: ‘resv_msi_base’ may be used uninitialized in this function [-Wmaybe-uninitialized]
ret = iommu_get_msi_cookie(domain->domain, resv_msi_base);
~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The warning is a false positive, because the call to iommu_get_msi_cookie()
only happens when vfio_iommu_has_sw_msi() returned true. And that only
happens when it also set resv_msi_base.
But initialize the variable anyway to get rid of the warning.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Code that iterates over all standard PCI BARs typically uses
PCI_STD_RESOURCE_END. However, that requires the unusual test
"i <= PCI_STD_RESOURCE_END" rather than something the typical
"i < PCI_STD_NUM_BARS".
Add a definition for PCI_STD_NUM_BARS and change loops to use the more
idiomatic C style to help avoid fencepost errors.
Link: https://lore.kernel.org/r/20190927234026.23342-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190927234308.23935-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190916204158.6889-3-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # arch/s390/
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> # video/fbdev/
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> # pci/controller/dwc/
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> # scsi/pm8001/
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi/pm8001/
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # memstick/
|
|
This patch is a part of a series that extends kernel ABI to allow to pass
tagged user pointers (with the top byte set to something else other than
0x00) as syscall arguments.
vaddr_get_pfn() uses provided user pointers for vma lookups, which can
only by done with untagged pointers.
Untag user pointers in this function.
Link: http://lkml.kernel.org/r/87422b4d72116a975896f2b19b00f38acbd28f33.1563904656.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Will Deacon <will@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace PAGE_SHIFT + compound_order(page) with the new page_shift()
function. Minor improvements in readability.
[akpm@linux-foundation.org: fix build in tce_page_is_contained()]
Link: http://lkml.kernel.org/r/201907241853.yNQTrJWd%25lkp@intel.com
Link: http://lkml.kernel.org/r/20190721104612.19120-3-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull VFIO updates from Alex Williamson:
- Fix spapr iommu error case case (Alexey Kardashevskiy)
- Consolidate region type definitions (Cornelia Huck)
- Restore saved original PCI state on release (hexin)
- Simplify mtty sample driver interrupt path (Parav Pandit)
- Support for reporting valid IOVA regions to user (Shameer Kolothum)
* tag 'vfio-v5.4-rc1' of git://github.com/awilliam/linux-vfio:
vfio_pci: Restore original state on release
vfio/type1: remove duplicate retrieval of reserved regions
vfio/type1: Add IOVA range capability support
vfio/type1: check dma map request is within a valid iova range
vfio/spapr_tce: Fix incorrect tce_iommu_group memory free
vfio-mdev/mtty: Simplify interrupt generation
vfio: re-arrange vfio region definitions
vfio/type1: Update iova list on detach
vfio/type1: Check reserved region conflict and update iova list
vfio/type1: Introduce iova list and add iommu aperture validity check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"This is a bit late, partly due to me travelling, and partly due to a
power outage knocking out some of my test systems *while* I was
travelling.
- Initial support for running on a system with an Ultravisor, which
is software that runs below the hypervisor and protects guests
against some attacks by the hypervisor.
- Support for building the kernel to run as a "Secure Virtual
Machine", ie. as a guest capable of running on a system with an
Ultravisor.
- Some changes to our DMA code on bare metal, to allow devices with
medium sized DMA masks (> 32 && < 59 bits) to use more than 2GB of
DMA space.
- Support for firmware assisted crash dumps on bare metal (powernv).
- Two series fixing bugs in and refactoring our PCI EEH code.
- A large series refactoring our exception entry code to use gas
macros, both to make it more readable and also enable some future
optimisations.
As well as many cleanups and other minor features & fixups.
Thanks to: Adam Zerella, Alexey Kardashevskiy, Alistair Popple, Andrew
Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman Khandual,
Balbir Singh, Benjamin Herrenschmidt, Cédric Le Goater, Christophe
JAILLET, Christophe Leroy, Christopher M. Riedl, Christoph Hellwig,
Claudio Carvalho, Daniel Axtens, David Gibson, David Hildenbrand,
Desnes A. Nunes do Rosario, Ganesh Goudar, Gautham R. Shenoy, Greg
Kurz, Guerney Hunt, Gustavo Romero, Halil Pasic, Hari Bathini, Joakim
Tjernlund, Jonathan Neuschafer, Jordan Niethe, Leonardo Bras, Lianbo
Jiang, Madhavan Srinivasan, Mahesh Salgaonkar, Mahesh Salgaonkar,
Masahiro Yamada, Maxiwell S. Garcia, Michael Anderson, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Oliver
O'Halloran, Qian Cai, Ram Pai, Ravi Bangoria, Reza Arbab, Ryan Grimm,
Sam Bobroff, Santosh Sivaraj, Segher Boessenkool, Sukadev Bhattiprolu,
Thiago Bauermann, Thiago Jung Bauermann, Thomas Gleixner, Tom
Lendacky, Vasant Hegde"
* tag 'powerpc-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (264 commits)
powerpc/mm/mce: Keep irqs disabled during lockless page table walk
powerpc: Use ftrace_graph_ret_addr() when unwinding
powerpc/ftrace: Enable HAVE_FUNCTION_GRAPH_RET_ADDR_PTR
ftrace: Look up the address of return_to_handler() using helpers
powerpc: dump kernel log before carrying out fadump or kdump
docs: powerpc: Add missing documentation reference
powerpc/xmon: Fix output of XIVE IPI
powerpc/xmon: Improve output of XIVE interrupts
powerpc/mm/radix: remove useless kernel messages
powerpc/fadump: support holes in kernel boot memory area
powerpc/fadump: remove RMA_START and RMA_END macros
powerpc/fadump: update documentation about option to release opalcore
powerpc/fadump: consider f/w load area
powerpc/opalcore: provide an option to invalidate /sys/firmware/opal/core file
powerpc/opalcore: export /sys/firmware/opal/core for analysing opal crashes
powerpc/fadump: update documentation about CONFIG_PRESERVE_FA_DUMP
powerpc/fadump: add support to preserve crash data on FADUMP disabled kernel
powerpc/fadump: improve how crashed kernel's memory is reserved
powerpc/fadump: consider reserved ranges while releasing memory
powerpc/fadump: make crash memory ranges array allocation generic
...
|
|
Invalidating a TCE cache entry for each updated TCE is quite expensive.
This makes use of the new iommu_table_ops::xchg_no_kill()/tce_kill()
callbacks to bring down the time spent in mapping a huge guest DMA window.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190829085252.72370-4-aik@ozlabs.ru
|
|
'v5.4/vfio/connie-re-arrange-v2', 'v5.4/vfio/hexin-pci-reset-v3', 'v5.4/vfio/parav-mtty-uuid-v2' and 'v5.4/vfio/shameer-iova-list-v8' into v5.4/vfio/next
|
|
vfio_pci_enable() saves the device's initial configuration information
with the intent that it is restored in vfio_pci_disable(). However,
the commit referenced in Fixes: below replaced the call to
__pci_reset_function_locked(), which is not wrapped in a state save
and restore, with pci_try_reset_function(), which overwrites the
restored device state with the current state before applying it to the
device. Reinstate use of __pci_reset_function_locked() to return to
the desired behavior.
Fixes: 890ed578df82 ("vfio-pci: Use pci "try" reset interface")
Signed-off-by: hexin <hexin15@baidu.com>
Signed-off-by: Liu Qi <liuqi16@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
As we now already have the reserved regions list, just pass that into
vfio_iommu_has_sw_msi() fn.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
This allows the user-space to retrieve the supported IOVA
range(s), excluding any non-relaxable reserved regions. The
implementation is based on capability chains, added to
VFIO_IOMMU_GET_INFO ioctl.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
This checks and rejects any dma map request outside valid iova
range.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The @tcegrp variable is used in 1) a loop over attached groups
2) it stores a pointer to a newly allocated tce_iommu_group if 1) found
nothing. However the error handler does not distinguish how we got there
and incorrectly releases memory for a found+incompatible group.
This fixes it by adding another error handling case.
Fixes: 0bd971676e68 ("powerpc/powernv/npu: Add compound IOMMU groups")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Get a copy of iova list on _group_detach and try to update the list.
On success replace the current one with the copy. Leave the list as
it is if update fails.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
This retrieves the reserved regions associated with dev group and
checks for conflicts with any existing dma mappings. Also update
the iova list excluding the reserved regions.
Reserved regions with type IOMMU_RESV_DIRECT_RELAXABLE are
excluded from above checks as they are considered as directly
mapped regions which are known to be relaxable.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
This introduces an iova list that is valid for dma mappings. Make
sure the new iommu aperture window doesn't conflict with the current
one or with any existing dma mappings during attach.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
To permit batching of TLB flushes across multiple calls to the IOMMU
driver's ->unmap() implementation, introduce a new structure for
tracking the address range to be flushed and the granularity at which
the flushing is required.
This is hooked into the IOMMU API and its caller are updated to make use
of the new structure. Subsequent patches will plumb this into the IOMMU
drivers as well, but for now the gathering information is ignored.
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Commit add02cfdc9bc ("iommu: Introduce Interface for IOMMU TLB Flushing")
added three new TLB flushing operations to the IOMMU API so that the
underlying driver operations can be batched when unmapping large regions
of IO virtual address space.
However, the ->iotlb_range_add() callback has not been implemented by
any IOMMU drivers (amd_iommu.c implements it as an empty function, which
incurs the overhead of an indirect branch). Instead, drivers either flush
the entire IOTLB in the ->iotlb_sync() callback or perform the necessary
invalidation during ->unmap().
Attempting to implement ->iotlb_range_add() for arm-smmu-v3.c revealed
two major issues:
1. The page size used to map the region in the page-table is not known,
and so it is not generally possible to issue TLB flushes in the most
efficient manner.
2. The only mutable state passed to the callback is a pointer to the
iommu_domain, which can be accessed concurrently and therefore
requires expensive synchronisation to keep track of the outstanding
flushes.
Remove the callback entirely in preparation for extending ->unmap() and
->iotlb_sync() to update a token on the caller's stack.
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Pull VFIO updates from Alex Williamson:
- Static symbol cleanup in mdev samples (Kefeng Wang)
- Use vma help in nvlink code (Peng Hao)
- Remove unused code in mbochs sample (YueHaibing)
- Send uevents around mdev registration (Alex Williamson)
* tag 'vfio-v5.3-rc1' of git://github.com/awilliam/linux-vfio:
mdev: Send uevents around parent device registration
sample/mdev/mbochs: remove set but not used variable 'mdev_state'
vfio: vfio_pci_nvlink2: use a vma helper function
vfio-mdev/samples: make some symbols static
|
