summaryrefslogtreecommitdiff
path: root/drivers/usb
AgeCommit message (Collapse)Author
2014-01-13usb: chipidea: put hw_phymode_configure before ci_usb_phy_initChris Ruehl
hw_phymode_configure configures the PORTSC registers and allow the following phy_inits to operate on the right parameters. This fix a problem where the UPLI (ISP1504) could not be detected, because the Viewport was not available and read the viewport return 0's only. Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-13usb: chipidea: Fix Internal error: : 808 [#1] ARM related to STS flagChris Ruehl
* init the sts flag to 0 (missed) * fix write the real bit not sts value * Set PORTCS_STS and DEVLC_STS only if sts = 1 [Peter Chen: This one and the next patch fix the problem occurred imx27 and imx31, and imx27 and imx31 usb support are enabled until 3.14, so these two patches isn't needed for -stable] Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-13usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28Peter Chen
Due to imx28 needs ARM swp instruction for writing, we set CI_HDRC_IMX28_WRITE_FIX for imx28. This patch is needed for stable tree 3.11+ Cc: stable@vger.kernel.org Cc: robert.hodaszi@digi.com Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-13usb: chipidea: add freescale imx28 special write register methodPeter Chen
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB register error issue", All USB register write operations must use the ARM SWP instruction. So, we implement special hw_write and hw_test_and_clear for imx28. Discussion for it at below: http://marc.info/?l=linux-usb&m=137996395529294&w=2 This patch is needed for stable tree 3.11+. Cc: stable@vger.kernel.org Cc: robert.hodaszi@digi.com Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-13usb: ehci: add freescale imx28 special write register methodPeter Chen
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB register error issue", All USB register write operations must use the ARM SWP instruction. So, we implement a special ehci_write for imx28. Discussion for it at below: http://marc.info/?l=linux-usb&m=137996395529294&w=2 Without this patcheset, imx28 works unstable at high AHB bus loading. If the bus loading is not high, the imx28 usb can work well at the most of time. There is a IC errata for this problem, usually, we consider IC errata is a problem not a new feature, and this workaround is needed for that, so we need to add them to stable tree 3.11+. Cc: stable@vger.kernel.org Cc: robert.hodaszi@digi.com Signed-off-by: Peter Chen <peter.chen@freescale.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-13usb: core: check for valid id_table when using the RefId featureWolfram Sang
When implementing the RefId feature, it was missed that id_tables can be NULL under special circumstances. Bail out in that case. Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-13Move DWC2 driver out of stagingPaul Zimmerman
The DWC2 driver should now be in good enough shape to move out of staging. I have stress tested it overnight on RPI running mass storage and Ethernet transfers in parallel, and for several days on our proprietary PCI-based platform. Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-12usb: cdc-wdm: resp_count can be 0 even if WDM_READ is setBjørn Mork
Do not decrement resp_count if it's already 0. We set resp_count to 0 when the device is closed. The next open and read will try to clear the WDM_READ flag if there was leftover data in the read buffer. This fix is necessary to prevent resubmitting the read URB in a tight loop because resp_count becomes negative. The bug can easily be triggered from userspace by not reading all data in the read buffer, and then closing and reopening the chardev. Fixes: 8dd5cd5395b9 ("usb: cdc-wdm: avoid hanging on zero length reads") Cc: <stable@vger.kernel.org> # 3.13 Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-12usb: core: bail out if user gives an unknown RefId when using new_idWolfram Sang
If users use the new RefId feature of new_id, give them an error message if they provided an unknown reference. That helps detecting typos. Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-12Merge branch 'acpi-hotplug'Rafael J. Wysocki
* acpi-hotplug: ACPI / scan: ACPI device object sysfs attribute for _STA evaluation ACPI / hotplug / driver core: Handle containers in a special way ACPI / hotplug: Add demand_offline hotplug profile flag ACPI / bind: Move acpi_get_child() to drivers/ide/ide-acpi.c ACPI / bind: Pass struct acpi_device pointer to acpi_bind_one() ACPI / bind: Rework struct acpi_bus_type ACPI / bind: Redefine acpi_preset_companion() ACPI / bind: Redefine acpi_get_child() PCI / ACPI: Use acpi_find_child_device() for child devices lookup ACPI / bind: Simplify child device lookups ACPI / scan: Use direct recurrence for device hierarchy walks ACPI: Introduce acpi_set_device_status() ACPI / hotplug: Drop unfinished global notification handling routines ACPI / hotplug: Rework generic code to handle suprise removals ACPI / hotplug: Move container-specific code out of the core ACPI / hotplug: Make ACPI PCI root hotplug use common hotplug code ACPI / hotplug: Introduce common hotplug function acpi_device_hotplug() ACPI / hotplug: Do not fail bus and device checks for disabled hotplug ACPI / scan: Add acpi_device objects for all device nodes in the namespace ACPI / scan: Define non-empty device removal handler
2014-01-12Merge branch 'acpi-cleanup'Rafael J. Wysocki
* acpi-cleanup: (22 commits) ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment. ACPI / tables: Check if id is NULL in acpi_table_parse() ACPI / proc: Include appropriate header file in proc.c ACPI / EC: Remove unused functions and add prototype declaration in internal.h ACPI / dock: Include appropriate header file in dock.c ACPI / PCI: Include appropriate header file in pci_link.c ACPI / PCI: Include appropriate header file in pci_slot.c ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c ACPI / NVS: Include appropriate header file in nvs.c ACPI / OSL: Mark the function acpi_table_checksum() as static ACPI / processor: initialize a variable to silence compiler warning ACPI / processor: use ACPI_COMPANION() to get ACPI device ACPI: correct minor typos ACPI / sleep: Drop redundant acpi_disabled check ACPI / dock: Drop redundant acpi_disabled check ACPI / table: Replace '1' with specific error return values ACPI: remove trailing whitespace ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h> SFI / ACPI: Fix warnings reported during builds with W=1 ... Conflicts: drivers/acpi/nvs.c drivers/hwmon/asus_atk0110.c
2014-01-12USB: fsl-mph-dr-of: adjust for OF based clock lookupGerhard Sittig
after device tree based clock lookup became available, the peripheral driver need no longer construct clock names which include the component index -- remove the "usb%d_clk" template, always use "ipg" instead Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-usb@vger.kernel.org Signed-off-by: Gerhard Sittig <gsi@denx.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2014-01-10usb: core: allow a reference device for new_idWolfram Sang
Often, usb drivers need some driver_info to get a device to work. To have access to driver_info when using new_id, allow to pass a reference vendor:product tuple from which new_id will inherit driver_info. Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-10usb: core: add sanity checks when using bInterfaceClass with new_idWolfram Sang
Check if that field is actually used and if so, bail out if it exeeds a u8. Make it also future-proof by not requiring "exactly three" parameters in new_id, but simply "more than two". Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-09Merge branch 'qcom/drivers' into next/driversOlof Johansson
* qcom/drivers: tty: serial: Limit msm_serial_hs driver to platforms that use it mmc: msm_sdcc: Limit driver to platforms that use it usb: phy: msm: Move mach dependent code to platform data Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-09usb: phy: msm: Move mach dependent code to platform dataIvan T. Ivanov
This patch fix compilation error when driver is compiled in multi-platform builds. drivers/built-in.o: In function `msm_otg_link_clk_reset': ./drivers/usb/phy/phy-msm-usb.c:314: undefined reference to `clk_reset' ./drivers/usb/phy/phy-msm-usb.c:318: undefined reference to `clk_reset' Use platform data supplied reset handlers and adjust error messages reported when reset sequence fail. This is an intermediate step before adding support for reset framework and newer targets. Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> Acked-by: David Brown <davidb@codeaurora.org> Cc: Daniel Walker <dwalker@fifo99.com> Acked-by: Felipe Balbi <balbi@ti.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-08USB: image: correct spelling mistake in commentRahul Bedarkar
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-08USB: c67x00: correct spelling mistakes in commentsRahul Bedarkar
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-08usb: delete non-required instances of include <linux/init.h>Paul Gortmaker
None of these files are actually using any __init type directives and hence don't need to include <linux/init.h>. Most are just a left over from __devinit and __cpuinit removal, or simply due to code getting copied from one driver to the next. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-08usb:hub set hub->change_bits when over-current happensShen Guang
When we are doing compliance test with xHCI, we found that if we enable CONFIG_USB_SUSPEND and plug in a bad device which causes over-current condition to the root port, software will not be noticed. The reason is that current code don't set hub->change_bits in hub_activate() when over-current happens, and then hub_events() will not check the port status because it thinks nothing changed. If CONFIG_USB_SUSPEND is disabled, the interrupt pipe of the hub will report the change and set hub->event_bits, and then hub_events() will check what events happened.In this case over-current can be detected. Signed-off-by: Shen Guang <shenguang10@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-08Revert "usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28"Greg Kroah-Hartman
This reverts commit 30666249eae3b04875d514dea557d1ab1468c006, as it depended on a previous patch that I rejected, causing a build error here. Sorry about that. Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: Peter Chen <peter.chen@freescale.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-08xhci: Set scatter-gather limit to avoid failed block writes.Sarah Sharp
Commit 35773dac5f862cb1c82ea151eba3e2f6de51ec3e "usb: xhci: Link TRB must not occur within a USB payload burst" attempted to fix an issue found with USB ethernet adapters, and inadvertently broke USB storage devices. The patch attempts to ensure that transfers never span a segment, and rejects transfers that have more than 63 entries (or possibly less, if some entries cross 64KB boundaries). usb-storage limits the maximum transfer size to 120K, and we had assumed the block layer would pass a scatter-gather list of 4K entries, resulting in no more than 31 sglist entries: http://marc.info/?l=linux-usb&m=138498190419312&w=2 That assumption was wrong, since we've seen the driver reject a write that was 218 sectors long (of probably 512 bytes each): Jan 1 07:04:49 jidanni5 kernel: [ 559.624704] xhci_hcd 0000:00:14.0: Too many fragments 79, max 63 ... Jan 1 07:04:58 jidanni5 kernel: [ 568.622583] Write(10): 2a 00 00 06 85 0e 00 00 da 00 Limit the number of scatter-gather entries to half a ring segment. That should be margin enough in case some entries cross 64KB boundaries. Increase the number of TRBs per segment from 64 to 256, which should result in ring segments fitting on a 4K page. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: jidanni@jidanni.org References: http://bugs.debian.org/733907 Fixes: 35773dac5f86 ('usb: xhci: Link TRB must not occur within a USB payload burst') Cc: stable <stable@vger.kernel.org> # 3.12
2014-01-08xhci: Avoid infinite loop when sg urb requires too many trbsBen Hutchings
Currently prepare_ring() returns -ENOMEM if the urb won't fit into a single ring segment. usb_sg_wait() treats this error as a temporary condition and will keep retrying until something else goes wrong. The number of retries should be limited in usb_sg_wait(), but also prepare_ring() should not return an error code that suggests it might be worth retrying. Change it to -EINVAL. Reported-by: jidanni@jidanni.org References: http://bugs.debian.org/733907 Fixes: 35773dac5f86 ('usb: xhci: Link TRB must not occur within a USB payload burst') Cc: stable <stable@vger.kernel.org> # 3.12 Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-01-07usb: gadget: remove unused variable in gr_queue_int()Wei Yongjun
The variable 'dev' is initialized but never used otherwise, so remove the unused variable. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07usb: gadget: s3c-hsotg: remove duplicated include from s3c-hsotg.cWei Yongjun
Remove duplicated include. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: ftdi_sio: added CS5 quirk for broken smartcard readersColin Leitner
Genuine FTDI chips support only CS7/8. A previous fix in commit 8704211f65a2 ("USB: ftdi_sio: fixed handling of unsupported CSIZE setting") enforced this limitation and reported it back to userspace. However, certain types of smartcard readers depend on specific driver behaviour that requests 0 data bits (not 5) to change into a different operating mode if CS5 has been set. This patch reenables this behaviour for all FTDI devices. Tagged to be added to stable, because it affects a lot of users of embedded systems which rely on these readers to work properly. Cc: stable <stable@vger.kernel.org> Reported-by: Heinrich Siebmanns <H.Siebmanns@t-online.de> Tested-by: Heinrich Siebmanns <H.Siebmanns@t-online.de> Signed-off-by: Colin Leitner <colin.leitner@gmail.com> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28Peter Chen
Due to imx28 needs ARM swp instruction for writing, we set CI_HDRC_IMX28_WRITE_FIX for imx28. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07usb: chipidea: mark register map as "const" and convert to u8Marc Kleine-Budde
This patch makes the controller register map ci_regs_nolpm and ci_regs_lpm as "const". Further, as all offset fit into a single byte, the type is changed from uintptr_t to u8. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07usb: chipidea: move malloced regmap directly into struct hw_bankMarc Kleine-Budde
Without this patch a seperate chunk of memory is allocated for the regmap array. As the regmap is always used it makes no sense to allocate a seperate memory block for it, this patch moves the regmap array directly into the struct hw_bank. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: wusbcore: fix up coding style issues in wa-nep.cRahul Bedarkar
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: wusbcore: fix up coding style issues in wa-rpipe.cRahul Bedarkar
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: wusbcore: fix up coding style issues in wusbhc.c and wusbhc.hRahul Bedarkar
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: wusbcore: fix up line break coding style issues in mmc.cRahul Bedarkar
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: wusbcore: fix up line break coding style issues in security.cRahul Bedarkar
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: wusbcore: fix up line break coding style issues in wa-hc.hRahul Bedarkar
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: wusbcore: fix up minor coding style issues in cbaf.cRahul Bedarkar
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: wusbcore: correct spelling mistakes in comments and error stringRahul Bedarkar
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: core: correct spelling mistakes in comments and warningRahul Bedarkar
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: c67x00: move URB private data allocation from under spinlockMax Filippov
This fixes the following warning: BUG: sleeping function called from invalid context at mm/slub.c:940 in_atomic(): 1, irqs_disabled(): 1, pid: 17, name: khubd CPU: 0 PID: 17 Comm: khubd Not tainted 3.12.0-00004-g938dd60-dirty #1 __might_sleep+0xbe/0xc0 kmem_cache_alloc_trace+0x36/0x170 c67x00_urb_enqueue+0x5c/0x254 usb_hcd_submit_urb+0x66e/0x724 usb_submit_urb+0x2ac/0x308 usb_start_wait_urb+0x2c/0xb8 usb_control_msg+0x8c/0xa8 hub_port_init+0x191/0x718 hub_thread+0x804/0xe14 kthread+0x72/0x78 ret_from_kernel_thread+0x8/0xc Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Peter Korsgaard <peter@korsgaard.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: c67x00: add proper delays to HPI read/writeMax Filippov
According to CY7C67300 specification HPI read and write cycle duration Tcyc must be at least 6T long, where T is 1/48MHz, which is 125ns. Without this delay fast host processor cannot write to chip registers. Add proper ndelay to hpi_{read,write}_reg. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Peter Korsgaard <peter@korsgaard.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: fix race between hub_disconnect and recursively_mark_NOTATTACHEDAlan Stern
There is a race in the hub driver between hub_disconnect() and recursively_mark_NOTATTACHED(). This race can be triggered if the driver is unbound from a device at the same time as the bus's root hub is removed. When the race occurs, it can cause an oops: BUG: unable to handle kernel NULL pointer dereference at 0000015c IP: [<c16d5fb0>] recursively_mark_NOTATTACHED+0x20/0x60 Call Trace: [<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60 [<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60 [<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60 [<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60 [<c16d6082>] usb_set_device_state+0x92/0x120 [<c16d862b>] usb_disconnect+0x2b/0x1a0 [<c16dd4c0>] usb_remove_hcd+0xb0/0x160 [<c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50 [<c1704efc>] ehci_mid_remove+0x1c/0x30 [<c1704f26>] ehci_mid_stop_host+0x16/0x30 [<c16f7698>] penwell_otg_work+0xd28/0x3520 [<c19c945b>] ? __schedule+0x39b/0x7f0 [<c19cdb9d>] ? sub_preempt_count+0x3d/0x50 [<c125e97d>] process_one_work+0x11d/0x3d0 [<c19c7f4d>] ? mutex_unlock+0xd/0x10 [<c125e0e5>] ? manage_workers.isra.24+0x1b5/0x270 [<c125f009>] worker_thread+0xf9/0x320 [<c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50 [<c125ef10>] ? rescuer_thread+0x2b0/0x2b0 [<c1264ac4>] kthread+0x94/0xa0 [<c19d0f77>] ret_from_kernel_thread+0x1b/0x28 [<c1264a30>] ? kthread_create_on_node+0xc0/0xc0 One problem is that recursively_mark_NOTATTACHED() uses the intfdata value and hub->hdev->maxchild while hub_disconnect() is clearing them. Another problem is that it uses hub->ports[i] while the port device is being released. To fix this race, we need to hold the device_state_lock while hub_disconnect() changes the values. (Note that usb_disconnect() and hub_port_connect_change() already acquire this lock at similar critical times during a USB device's life cycle.) We also need to remove the port devices after maxchild has been set to 0, instead of before. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: "Du, Changbin" <changbinx.du@intel.com> Tested-by: "Du, Changbin" <changbinx.du@intel.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07USB: fix: ohci-at91 mismerge build errorArnd Bergmann
After commit 99f14bd4d1 "Merge 3.13-rc5 into usb-next" (in linux-next as of today), I'm getting this error building any at91 kernel: drivers/usb/host/ohci-at91.c: In function 'usb_hcd_at91_probe': drivers/usb/host/ohci-at91.c:190:4: error: label 'err' used but not defined goto err; ^ drivers/usb/host/ohci-at91.c: At top level: drivers/usb/host/ohci-at91.c:206:2: warning: data definition has no type or storage class [enabled by default] at91_stop_hc(pdev); ^ ... The problem is obviously a mismerge between two unrelated changes that resulted in missing opening braces. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Boris BREZILLON <b.brezillon@overkiz.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07treewide: fix comments and printk msgsMasanari Iida
This patch fixed several typo in printk from various part of kernel source. Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2014-01-03USB: oti6858: switch to generic TIOCMIWAIT implementationJohan Hovold
Switch to the generic TIOCMIWAIT implementation. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-03USB: oti6858: only wake up MSR queue on changesJohan Hovold
Only wake up MSR wait queue on actual modem-status changes. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-03USB: ch341: clean up interrupt handlerJohan Hovold
Clean up interrupt completion handler somewhat. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-03USB: ch341: switch to generic TIOCMIWAIT implementationJohan Hovold
Switch to the generic TIOCMIWAIT implementation which does not suffer from the races involved when using the deprecated sleep_on functions. Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-03USB: ch341: only wake up MSR queue on changesJohan Hovold
Only wake up MSR wait queue on actual modem-status changes. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-03USB: ch341: fix ignored TIOCMIWAIT maskJohan Hovold
Make sure the TIOCMIWAIT mask is always honoured. The CH341 interrupt status has a multiple-status changed flag which indicates that multiple status changes has occurred since last interrupt event. Unfortunately, if the final status is the same, there appears to be no way to determine which signal(s) has changed (an even number of times). This means that the multiple-status flag should not be used in TIOCMIWAIT as it leads to the signal mask argument being ignored (e.g. TIOCMIWAIT could return if DSR changes twice, even though the user only cares about carrier changes). Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-03USB: ch341: clean up line-status handlingJohan Hovold
Clean up line-status handling. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-05 00:51:32 +0000