| Age | Commit message (Collapse) | Author |
|---|
|
USBTMC devices are required to have a bulk-in and a bulk-out endpoint,
but the driver failed to verify this, something which could lead to the
endpoint addresses being taken from uninitialised memory.
Make sure to zero all private data as part of allocation, and add the
missing endpoint sanity check.
Note that this also addresses a more recently introduced issue, where
the interrupt-in-presence flag would also be uninitialised whenever the
optional interrupt-in endpoint is not present. This in turn could lead
to an interrupt urb being allocated, initialised and submitted based on
uninitialised values.
Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.")
Fixes: 5b775f672cc9 ("USB: add USB test and measurement class driver")
Cc: stable <stable@vger.kernel.org> # 2.6.28
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by
qcserial due to a USB VID/PID conflict with an existing Acer
device.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The DSPS glue calls del_timer_sync() in its musb_platform_disable()
implementation, which requires the caller to not hold a lock. But
musb_remove() calls musb_platform_disable() will musb->lock held. This
could causes spinlock deadlock.
So change musb_remove() to call musb_platform_disable() without holds
musb->lock. This doesn't impact the musb_platform_disable implementation
in other glue drivers.
root@am335x-evm:~# modprobe -r musb-dsps
[ 126.134879] musb-hdrc musb-hdrc.1: remove, state 1
[ 126.140465] usb usb2: USB disconnect, device number 1
[ 126.146178] usb 2-1: USB disconnect, device number 2
[ 126.416985] musb-hdrc musb-hdrc.1: USB bus 2 deregistered
[ 126.423943]
[ 126.425525] ======================================================
[ 126.431997] [ INFO: possible circular locking dependency detected ]
[ 126.438564] 4.11.0-rc1-00003-g1557f13bca04-dirty #77 Not tainted
[ 126.444852] -------------------------------------------------------
[ 126.451414] modprobe/778 is trying to acquire lock:
[ 126.456523] (((&glue->timer))){+.-...}, at: [<c01b8788>] del_timer_sync+0x0/0xd0
[ 126.464403]
[ 126.464403] but task is already holding lock:
[ 126.470511] (&(&musb->lock)->rlock){-.-...}, at: [<bf30b7f8>] musb_remove+0x50/0x1
30 [musb_hdrc]
[ 126.479965]
[ 126.479965] which lock already depends on the new lock.
[ 126.479965]
[ 126.488531]
[ 126.488531] the existing dependency chain (in reverse order) is:
[ 126.496368]
[ 126.496368] -> #1 (&(&musb->lock)->rlock){-.-...}:
[ 126.502968] otg_timer+0x80/0xec [musb_dsps]
[ 126.507990] call_timer_fn+0xb4/0x390
[ 126.512372] expire_timers+0xf0/0x1fc
[ 126.516754] run_timer_softirq+0x80/0x178
[ 126.521511] __do_softirq+0xc4/0x554
[ 126.525802] irq_exit+0xe8/0x158
[ 126.529735] __handle_domain_irq+0x58/0xb8
[ 126.534583] __irq_usr+0x54/0x80
[ 126.538507]
[ 126.538507] -> #0 (((&glue->timer))){+.-...}:
[ 126.544636] del_timer_sync+0x40/0xd0
[ 126.549066] musb_remove+0x6c/0x130 [musb_hdrc]
[ 126.554370] platform_drv_remove+0x24/0x3c
[ 126.559206] device_release_driver_internal+0x14c/0x1e0
[ 126.565225] bus_remove_device+0xd8/0x108
[ 126.569970] device_del+0x1e4/0x308
[ 126.574170] platform_device_del+0x24/0x8c
[ 126.579006] platform_device_unregister+0xc/0x20
[ 126.584394] dsps_remove+0x14/0x30 [musb_dsps]
[ 126.589595] platform_drv_remove+0x24/0x3c
[ 126.594432] device_release_driver_internal+0x14c/0x1e0
[ 126.600450] driver_detach+0x38/0x6c
[ 126.604740] bus_remove_driver+0x4c/0xa0
[ 126.609407] SyS_delete_module+0x11c/0x1e4
[ 126.614252] __sys_trace_return+0x0/0x10
Fixes: ea2f35c01d5ea ("usb: musb: Fix sleeping function called from invalid context for hdrc glue")
Cc: <stable@vger.kernel.org> #4.9+
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Cleanly iounmap the pointer in error and exit paths.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The CPPI 4.1 driver polls register to workaround the premature TX
interrupt issue, but it causes audio playback underrun when triggered in
Isoch transfers.
Isoch doesn't do back-to-back transfers, the TX should be done by the
time the next transfer is scheduled. So skip this polling workaround for
Isoch transfer.
Fixes: a655f481d83d6 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt")
Cc: <stable@vger.kernel.org> #4.1+
Reported-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.
The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms. It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies. The generic config code does not
catch this case because the 64ms is considered a sane enough value.
This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
This specifically fixes the NULL-pointer dereference when probing HWA HC
devices.
Fixes: df3654236e31 ("wusb: add the Wire Adapter (WA) core")
Cc: stable <stable@vger.kernel.org> # 2.6.28
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Note that the endpoint access that causes the NULL-deref is currently
only used for debugging purposes during probe so the oops only happens
when dynamic debugging is enabled. This means the driver could be
rewritten to continue to accept device with only two endpoints, should
such devices exist.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should the probed device lack endpoints.
Note that this driver does not bind to any devices by default.
Fixes: ce21bfe603b3 ("USB: Add LVS Test device driver")
Cc: stable <stable@vger.kernel.org> # 3.17
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a number of different USB fixes for 4.11-rc2.
Seems like there were a lot of unresolved issues that people have been
finding for this subsystem, and a bunch of good security auditing
happening as well from Johan Hovold. There's the usual batch of gadget
driver fixes and xhci issues resolved as well.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
usb: host: xhci-plat: Fix timeout on removal of hot pluggable xhci controllers
usb: host: xhci-dbg: HCIVERSION should be a binary number
usb: xhci: remove dummy extra_priv_size for size of xhci_hcd struct
usb: xhci-mtk: check hcc_params after adding primary hcd
USB: serial: digi_acceleport: fix OOB-event processing
MAINTAINERS: usb251xb: remove reference inexistent file
doc: dt-bindings: usb251xb: mark reg as required
usb: usb251xb: dt: add unit suffix to oc-delay and power-on-time
usb: usb251xb: remove max_{power,current}_{sp,bp} properties
usb-storage: Add ignore-residue quirk for Initio INIC-3619
USB: iowarrior: fix NULL-deref in write
USB: iowarrior: fix NULL-deref at probe
usb: phy: isp1301: Add OF device ID table
usb: ohci-at91: Do not drop unhandled USB suspend control requests
USB: serial: safe_serial: fix information leak in completion handler
USB: serial: io_ti: fix information leak in completion handler
USB: serial: omninet: drop open callback
USB: serial: omninet: fix reference leaks at open
USB: serial: io_ti: fix NULL-deref in interrupt callback
usb: dwc3: gadget: make to increment req->remaining in all cases
...
|
|
Fix typos and add the following to the scripts/spelling.txt:
disble||disable
disbled||disabled
I kept the TSL2563_INT_DISBLED in /drivers/iio/light/tsl2563.c
untouched. The macro is not referenced at all, but this commit is
touching only comment blocks just in case.
Link: http://lkml.kernel.org/r/1481573103-11329-20-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Upstream commit 98d74f9ceaef ("xhci: fix 10 second timeout on removal of
PCI hotpluggable xhci controllers") fixes a problem with hot pluggable PCI
xhci controllers which can result in excessive timeouts, to the point where
the system reports a deadlock.
The same problem is seen with hot pluggable xhci controllers using the
xhci-plat driver, such as the driver used for Type-C ports on rk3399.
Similar to hot-pluggable PCI controllers, the driver for this chip
removes the xhci controller from the system when the Type-C cable is
disconnected.
The solution for PCI devices works just as well for non-PCI devices
and avoids the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to xHCI spec, HCIVERSION containing a BCD encoding
of the xHCI specification revision number, 0100h corresponds
to xHCI version 1.0. Change "100" as "0x100".
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 04abb6de2825 ("xhci: Read and parse new xhci
1.1 capability register")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
because hcd_priv_size is already size of xhci_hcd struct,
extra_priv_size is not needed anymore for MTK and tegra drivers.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
hcc_params is set in xhci_gen_setup() called from usb_add_hcd(),
so checks the Maximum Primary Stream Array Size in the hcc_params
register after adding primary hcd.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.11-rc2
Here's a fix for a digi_acceleport regression in -rc1, and some fixes
for long-standing issues in three other drivers, including a
NULL-pointer dereference and a couple of information leaks that could be
triggered by a malicious device.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
A recent change claimed to fix an off-by-one error in the OOB-port
completion handler, but instead introduced such an error. This could
specifically led to modem-status changes going unnoticed, effectively
breaking TIOCMGET.
Note that the offending commit fixes a loop-condition underflow and is
marked for stable, but should not be backported without this fix.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2d380889215f ("USB: serial: digi_acceleport: fix OOB data sanity check")
Cc: stable <stable@vger.kernel.org> # v2.6.30
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename oc-delay-* to oc-delay-us and make it expect a time value.
Furthermore add -ms suffix to power-on-time. There changes were
suggested by Rob Herring in https://lkml.org/lkml/2017/2/15/1283.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the max_{power,current}_{sp,bp} properties of the usb251xb driver
from devicetree. This is done to simplify the dt bindings as requested
by Rob Herring in https://lkml.org/lkml/2017/2/15/1283. If those
properties are ever needed by somebody they can be enabled again easily.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This USB-SATA bridge chip is used in a StarTech enclosure for
optical drives.
Without the quirk MakeMKV fails during the key exchange with an
installed BluRay drive:
> Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED'
> occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:2'
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to verify that we have the required interrupt-out endpoint for
IOWarrior56 devices to avoid dereferencing a NULL-pointer in write
should a malicious device lack such an endpoint.
Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to check for the required interrupt-in endpoint to avoid
dereferencing a NULL-pointer should a malicious device lack such an
endpoint.
Note that a fairly recent change purported to fix this issue, but added
an insufficient test on the number of endpoints only, a test which can
now be removed.
Fixes: 4ec0ef3a8212 ("USB: iowarrior: fix oops with malicious USB descriptors")
Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In patch 2e2aa1bc7eff90ecm, USB suspend and wakeup control requests are
passed to SFR_OHCIICR register. If a processor does not have such a
register, this hub control request will be dropped.
If no such a SFR register is available, all USB suspend control requests
will now be processed using ohci_hub_control()
(like before patch 2e2aa1bc7eff90ecm.)
Tested on an Atmel AT91SAM9G20 with an on-board TI TUSB2046B hub chip
If the last USB device is unplugged from the USB hub, the hub goes into
sleep and will not wakeup when an USB devices is inserted.
Fixes: 2e2aa1bc7eff90ec ("usb: ohci-at91: Forcibly suspend ports while USB suspend")
Signed-off-by: Jelle Martijn Kok <jmkok@youcom.nl>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that could be triggered by a malicious device.
This avoids leaking up to 56 bytes from after the URB transfer buffer to
user space.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that can be triggered by a malicious device.
This avoids leaking 128 kB of memory content from after the URB transfer
buffer to user space.
Fixes: 8c209e6782ca ("USB: make actual_length in struct urb field u32")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Remove the now redundant open callback and let core call the generic
handler for us instead.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This driver needlessly took another reference to the tty on open, a
reference which was then never released on close. This lead to not just
a leak of the tty, but also a driver reference leak that prevented the
driver from being unloaded after a port had once been opened.
Fixes: 4a90f09b20f4 ("tty: usb-serial krefs")
Cc: stable <stable@vger.kernel.org> # 2.6.28
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Fix a NULL-pointer dereference in the interrupt callback should a
malicious device send data containing a bad port number by adding the
missing sanity check.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Sometimes, we might get a completion for a TRB which is left with HWO
bit. Even in these cases, we should increment req->remaining to
properly report total transferred size. I noticed this while debuggin
a separate problem seen with MSC tests from USBCV. Sometimes we would
erroneously report a completion for a 512-byte transfer when, in
reality, we transferred 0 bytes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In the function scan_dma_completions() there is a reusage of tmp
variable. That coused a wrong value being used in some case when
reading a short packet terminated transaction from an endpoint,
in 2 concecutive reads.
This was my logic for the patch:
The req->td->dmadesc equals to 0 iff:
-- There was a transaction ending with a short packet, and
-- The read() to read it was shorter than the transaction length, and
-- The read() to complete it is longer than the residue.
I believe this is true from the printouts of various cases,
but I can't be positive it is correct.
Entering this if, there should be no more data in the endpoint
(a short packet terminated the transaction).
If there is, the transaction wasn't really done and we should exit and
wait for it to finish entirely. That is the inner if.
That inner if should never happen, but it is there to be on the safe
side. That is why it is marked with the comment /* paranoia */.
The size of the data available in the endpoint is ep->dma->dmacount
and it is read to tmp.
This entire clause is based on my own educated guesses.
If we passed that inner if without breaking in the original code,
than tmp & DMA_BYTE_MASK_COUNT== 0.
That means we will always pass dma bytes count of 0 to dma_done(),
meaning all the requested bytes were read.
dma_done() reports back to the upper layer that the request (read())
was done and how many bytes were read.
In the original code that would always be the request size,
regardless of the actual size of the data.
That did not make sense to me at all.
However, the original value of tmp is req->td->dmacount,
which is the dmacount value when the request's dma transaction was
finished. And that is a much more reasonable value to report back to
the caller.
To recreate the problem:
Read from a bulk out endpoint in a loop, 1024 * n bytes in each
iteration.
Connect the PLX to a host you can control.
Send to that endpoint 1024 * n + x bytes,
such that 0 < x < 1024 * n and (x % 1024) != 0
You would expect the first read() to return 1024 * n
and the second read() to return x.
But you will get the first read to return 1024 * n
and the second one to return 1024 * n.
That is true for every positive integer n.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Raz Manor <Raz.Manor@valens.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
A call usb_put_phy(udc->transceiver) must be tested for a valid pointer.
Use an already existing test for usb_unregister_notifier call.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reported-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We need to break from all cases if we want to treat
each one of them separately.
Reported-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Fixes: d2728fb3e01f ("usb: dwc3: omap: Pass VBUS and ID events transparently")
Cc: <stable@vger.kernel.org> #v4.8+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
On TI platforms (dra7, am437x), the DWC3_DSTS_DEVCTRLHLT bit is not set
after the device controller is stopped via DWC3_DCTL_RUN_STOP.
If we don't disconnect and stop the gadget, it stops working after a
system resume with the trace below.
There is no point in preventing gadget disconnect and gadget stop during
system suspend/resume as we're going to suspend in any case, whether
DEVCTRLHLT timed out or not.
[ 141.727480] ------------[ cut here ]------------
[ 141.732349] WARNING: CPU: 1 PID: 2135 at drivers/usb/dwc3/gadget.c:2384 dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3]
[ 141.744299] Modules linked in: usb_f_ss_lb g_zero libcomposite xhci_plat_hcd xhci_hcd usbcore dwc3 evdev udc_core m25p80 usb_common spi_nor snd_soc_davinci_mcasp snd_soc_simple_card snd_soc_edma snd_soc_tlv3e
[ 141.792163] CPU: 1 PID: 2135 Comm: irq/456-dwc3 Not tainted 4.10.0-rc8 #1138
[ 141.799547] Hardware name: Generic DRA74X (Flattened Device Tree)
[ 141.805940] [<c01101b4>] (unwind_backtrace) from [<c010c31c>] (show_stack+0x10/0x14)
[ 141.814066] [<c010c31c>] (show_stack) from [<c04a0918>] (dump_stack+0xac/0xe0)
[ 141.821648] [<c04a0918>] (dump_stack) from [<c013708c>] (__warn+0xd8/0x104)
[ 141.828955] [<c013708c>] (__warn) from [<c0137164>] (warn_slowpath_null+0x20/0x28)
[ 141.836902] [<c0137164>] (warn_slowpath_null) from [<bf27784c>] (dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3])
[ 141.848329] [<bf27784c>] (dwc3_stop_active_transfer.constprop.4 [dwc3]) from [<bf27ab14>] (__dwc3_gadget_ep_disable+0x64/0x528 [dwc3])
[ 141.861034] [<bf27ab14>] (__dwc3_gadget_ep_disable [dwc3]) from [<bf27c27c>] (dwc3_gadget_ep_disable+0x3c/0xc8 [dwc3])
[ 141.872280] [<bf27c27c>] (dwc3_gadget_ep_disable [dwc3]) from [<bf23b428>] (usb_ep_disable+0x11c/0x18c [udc_core])
[ 141.883160] [<bf23b428>] (usb_ep_disable [udc_core]) from [<bf342774>] (disable_ep+0x18/0x54 [usb_f_ss_lb])
[ 141.893408] [<bf342774>] (disable_ep [usb_f_ss_lb]) from [<bf3437b0>] (disable_endpoints+0x18/0x50 [usb_f_ss_lb])
[ 141.904168] [<bf3437b0>] (disable_endpoints [usb_f_ss_lb]) from [<bf343814>] (disable_source_sink+0x2c/0x34 [usb_f_ss_lb])
[ 141.915771] [<bf343814>] (disable_source_sink [usb_f_ss_lb]) from [<bf329a9c>] (reset_config+0x48/0x7c [libcomposite])
[ 141.927012] [<bf329a9c>] (reset_config [libcomposite]) from [<bf329afc>] (composite_disconnect+0x2c/0x54 [libcomposite])
[ 141.938444] [<bf329afc>] (composite_disconnect [libcomposite]) from [<bf23d7dc>] (usb_gadget_udc_reset+0x10/0x34 [udc_core])
[ 141.950237] [<bf23d7dc>] (usb_gadget_udc_reset [udc_core]) from [<bf276d70>] (dwc3_gadget_reset_interrupt+0x64/0x698 [dwc3])
[ 141.962022] [<bf276d70>] (dwc3_gadget_reset_interrupt [dwc3]) from [<bf27952c>] (dwc3_thread_interrupt+0x618/0x1a3c [dwc3])
[ 141.973723] [<bf27952c>] (dwc3_thread_interrupt [dwc3]) from [<c01a7ce8>] (irq_thread_fn+0x1c/0x54)
[ 141.983215] [<c01a7ce8>] (irq_thread_fn) from [<c01a7fbc>] (irq_thread+0x120/0x1f0)
[ 141.991247] [<c01a7fbc>] (irq_thread) from [<c015ba14>] (kthread+0xf8/0x138)
[ 141.998641] [<c015ba14>] (kthread) from [<c01078f0>] (ret_from_fork+0x14/0x24)
[ 142.006213] ---[ end trace b4ecfe9f175b9a9c ]---
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This reverts commit ac670a3a650b899fc020b81f63e810d06015b865.
This introduce bug we already fixed in
commit 53642399aa71 ("usb: gadget: f_fs: Fix wrong check on reserved1 wof OS_DESC_EXT_COMPAT")
Next FFS (adb) SS enumeration fail with Windows OS.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
'kbuf' is allocated just a few lines above using 'memdup_user()'.
If the 'if (dev->buf)' test fails, this memory is never released.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The debug output now contains the wrong variable, as seen from the compiler
warning:
drivers/usb/gadget/udc/atmel_usba_udc.c: In function 'usba_ep_enable':
drivers/usb/gadget/udc/atmel_usba_udc.c:632:550: error: 'ept_cfg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
DBG(DBG_ERR, "%s: EPT_CFG = 0x%lx (maxpacket = %lu)\n",
This changes the debug output the same way as the other code.
Fixes: 741d2558bf0a ("usb: gadget: udc: atmel: Update endpoint allocation scheme")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The utmi mode is unsigned according the dt-bindings.
Fix sparse issue (-Wtypesign):
drivers/usb/dwc3/dwc3-omap.c:391:50: warning: incorrect type in argument 3 (different signedness)
drivers/usb/dwc3/dwc3-omap.c:391:50: expected unsigned int [usertype] *out_value
drivers/usb/dwc3/dwc3-omap.c:391:50: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When binding a gadget to a device, "name" is stored in gi->udc_name, but
this does not happen when unregistering and the string is leaked.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When the user does device unbind and rebind test, the kernel will
show below dump due to usb_gadget memory region is dirty after unbind.
Clear usb_gadget region for every new probe.
root@imx6qdlsolo:/sys/bus/platform/drivers/dummy_udc# echo dummy_udc.0 > bind
[ 102.523312] kobject (eddd78b0): tried to init an initialized object, something is seriously wrong.
[ 102.532447] CPU: 0 PID: 734 Comm: sh Not tainted 4.10.0-rc7-00872-g1b2b8e9 #1298
[ 102.539866] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[ 102.545717] Backtrace:
[ 102.548225] [<c010d090>] (dump_backtrace) from [<c010d338>] (show_stack+0x18/0x1c)
[ 102.555822] r7:ede34000 r6:60010013 r5:00000000 r4:c0f29418
[ 102.561512] [<c010d320>] (show_stack) from [<c040c2a4>] (dump_stack+0xb4/0xe8)
[ 102.568764] [<c040c1f0>] (dump_stack) from [<c040e6d4>] (kobject_init+0x80/0x9c)
[ 102.576187] r10:0000001f r9:eddd7000 r8:eeaf8c10 r7:eddd78a8 r6:c177891c r5:c0f3b060
[ 102.584036] r4:eddd78b0 r3:00000000
[ 102.587641] [<c040e654>] (kobject_init) from [<c05359a4>] (device_initialize+0x28/0xf8)
[ 102.595665] r5:eebc4800 r4:eddd78a8
[ 102.599268] [<c053597c>] (device_initialize) from [<c05382ac>] (device_register+0x14/0x20)
[ 102.607556] r7:eddd78a8 r6:00000000 r5:eebc4800 r4:eddd78a8
[ 102.613256] [<c0538298>] (device_register) from [<c0668ef4>] (usb_add_gadget_udc_release+0x8c/0x1ec)
[ 102.622410] r5:eebc4800 r4:eddd7860
[ 102.626015] [<c0668e68>] (usb_add_gadget_udc_release) from [<c0669068>] (usb_add_gadget_udc+0x14/0x18)
[ 102.635351] r10:0000001f r9:eddd7000 r8:eddd788c r7:bf003770 r6:eddd77f8 r5:eddd7818
[ 102.643198] r4:eddd785c r3:eddd7b24
[ 102.646834] [<c0669054>] (usb_add_gadget_udc) from [<bf003428>] (dummy_udc_probe+0x170/0x1c4 [dummy_hcd])
[ 102.656458] [<bf0032b8>] (dummy_udc_probe [dummy_hcd]) from [<c053d114>] (platform_drv_probe+0x54/0xb8)
[ 102.665881] r10:00000008 r9:c1778960 r8:bf004128 r7:fffffdfb r6:bf004128 r5:eeaf8c10
[ 102.673727] r4:eeaf8c10
[ 102.676293] [<c053d0c0>] (platform_drv_probe) from [<c053b160>] (driver_probe_device+0x264/0x474)
[ 102.685186] r7:00000000 r6:00000000 r5:c1778960 r4:eeaf8c10
[ 102.690876] [<c053aefc>] (driver_probe_device) from [<c05397c4>] (bind_store+0xb8/0x14c)
[ 102.698994] r10:eeb3bb4c r9:ede34000 r8:0000000c r7:eeaf8c44 r6:bf004128 r5:c0f3b668
[ 102.706840] r4:eeaf8c10
[ 102.709402] [<c053970c>] (bind_store) from [<c0538ca8>] (drv_attr_store+0x28/0x34)
[ 102.716998] r9:ede34000 r8:00000000 r7:ee3863c0 r6:ee3863c0 r5:c0538c80 r4:c053970c
[ 102.724776] [<c0538c80>] (drv_attr_store) from [<c029c930>] (sysfs_kf_write+0x50/0x54)
[ 102.732711] r5:c0538c80 r4:0000000c
[ 102.736313] [<c029c8e0>] (sysfs_kf_write) from [<c029be84>] (kernfs_fop_write+0x100/0x214)
[ 102.744599] r7:ee3863c0 r6:eeb3bb40 r5:00000000 r4:00000000
[ 102.750287] [<c029bd84>] (kernfs_fop_write) from [<c0222dd8>] (__vfs_write+0x34/0x120)
[ 102.758231] r10:00000000 r9:ede34000 r8:c0108bc4 r7:0000000c r6:ede35f80 r5:c029bd84
[ 102.766077] r4:ee223780
[ 102.768638] [<c0222da4>] (__vfs_write) from [<c0224678>] (vfs_write+0xa8/0x170)
[ 102.775974] r9:ede34000 r8:c0108bc4 r7:ede35f80 r6:01861cb0 r5:ee223780 r4:0000000c
[ 102.783743] [<c02245d0>] (vfs_write) from [<c0225498>] (SyS_write+0x4c/0xa8)
[ 102.790818] r9:ede34000 r8:c0108bc4 r7:0000000c r6:01861cb0 r5:ee223780 r4:ee223780
[ 102.798595] [<c022544c>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
[ 102.806188] r7:00000004 r6:b6e83d58 r5:01861cb0 r4:0000000c
Fixes: 90fccb529d24 ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Xiaolong Ye <xiaolong.ye@intel.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This reverts commit 4fbac5206afd01b717d4bdc58793d471f3391b4b.
This commit breaks g_webcam when used with uvc-gadget [1].
The user space application (e.g. uvc-gadget) is responsible for
sending response to UVC class specific requests on control endpoint
in uvc_send_response() in uvc_v4l2.c.
The bad commit was causing a duplicate response to be sent with
incorrect response data thus causing UVC probe to fail at the host
and broken control transfer endpoint at the gadget.
[1] - git://git.ideasonboard.org/uvc-gadget.git
Cc: <stable@vger.kernel.org> # v4.9+
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
A recent change claimed to fix an off-by-one error in the OOB-port
completion handler, but instead introduced such an error. This could
specifically led to modem-status changes going unnoticed, effectively
breaking TIOCMGET.
Note that the offending commit fixes a loop-condition underflow and is
marked for stable, but should not be backported without this fix.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2d380889215f ("USB: serial: digi_acceleport: fix OOB data sanity
check")
Cc: stable <stable@vger.kernel.org> # v2.6.30: 2d380889215f
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
If request was already started, this means we had to
stop the transfer. With that we also need to ignore
all TRBs used by the request, however TRBs can only
be modified after completion of END_TRANSFER
command. So what we have to do here is wait for
END_TRANSFER completion and only after that jump
over TRBs by clearing HWO and incrementing dequeue
pointer.
Note that we have 2 possible types of transfers
here:
i) Linear buffer request
ii) SG-list based request
SG-list based requests will have r->num_pending_sgs
set to a valid number (> 0). Linear requests,
normally use a single TRB.
For each of these two cases, if r->unaligned flag is
set, one extra TRB has been used to align transfer
size to wMaxPacketSize.
All of these cases need to be taken into
consideration so we don't mess up our TRB ring
pointers.
Tested-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
If we're dealing with SuperSpeed endpoints, we need
to make sure to pass along the companion descriptor
and initialize fields needed by the Gadget
API. Eventually, f_fs.c should be converted to use
config_ep_by_speed() like all other functions,
though.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Some gadget drivers are bad, bad boys. We notice
that ADB was passing bad Burst Size which caused top
bits of param0 to be overwritten which confused DWC3
when running this command.
In order to avoid future issues, we're going to make
sure values passed by macros are always safe for the
controller. Note that ADB still needs a fix to *not*
pass bad values.
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Mohamed Abbas <mohamed.abbas@intel.com>
Sugested-by: Adam Andruszak <adam.andruszak@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs sendmsg updates from Al Viro:
"More sendmsg work.
This is a fairly separate isolated stuff (there's a continuation
around lustre, but that one was too late to soak in -next), thus the
separate pull request"
* 'work.sendmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ncpfs: switch to sock_sendmsg()
ncpfs: don't mess with manually advancing iovec on send
ncpfs: sendmsg does *not* bugger iovec these days
ceph_tcp_sendpage(): use ITER_BVEC sendmsg
afs_send_pages(): use ITER_BVEC
rds: remove dead code
ceph: switch to sock_recvmsg()
usbip_recv(): switch to sock_recvmsg()
iscsi_target: deal with short writes on the tx side
[nbd] pass iov_iter to nbd_xmit()
[nbd] switch sock_xmit() to sock_{send,recv}msg()
[drbd] use sock_sendmsg()
|
|
related APIs from <linux/sched.h> to <linux/sched/task.h>
But first update usage sites with the new header dependency.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Update the .c files that depend on these APIs.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
