| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some remaining USB fixes for 4.13-rc1. They were originally
scheduled for 4.12-final, but I didn't send them to you in time.
Because of that, they were in a separate branch from the larger USB
set of patches, so here they are in a separate pull request.
Nothing major here a all, just three small patches:
- some usb-serial new device ids
- xhci bugfix for some crazy AMD hardware
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Limit USB2 port wake support for AMD Promontory hosts
USB: serial: qcserial: new Sierra Wireless EM7305 device ID
USB: serial: option: add two Longcheer device ids
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The big ticket items here are the rework of suspend-to-idle in order
to add proper support for power button wakeup from it on recent Dell
laptops and the rework of interfaces exporting the current CPU
frequency on x86.
In addition to that, support for a few new pieces of hardware is
added, the PCI/ACPI device wakeup infrastructure is simplified
significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
bus locking infrastructure.
Also, there are some functional improvements for intel_pstate, tools
updates and small fixes and cleanups all over.
Specifics:
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for the
Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that can
wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which allows
the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of RCU
which doesn't allow sleeping in the read-side critical sections,
but which in turn is expected to be allowed by the IRQ bus locking
infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance" P-state
selection algorithm is in use by making it avoid registering
scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in intel_pstate
by changing the values that correspond to different symbolic hint
names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
driver and clean up the sfi, exynos5440 and intel_pstate drivers
(Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski)"
* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
PM: hibernate: constify attribute_group structures.
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
PM / Domains: Fix missing default_power_down_ok comment
PM / Domains: Fix unsafe iteration over modified list of domains
PM / Domains: Fix unsafe iteration over modified list of domain providers
PM / Domains: Fix unsafe iteration over modified list of device links
PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
PM / Domains: Call driver's noirq callbacks
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
PM / QoS: constify *_attribute_group.
PM / AVS: rockchip-io: add io selectors and supplies for rk3228
powercap/RAPL: prevent overridding bits outside of the mask
PM / sysfs: Constify attribute groups
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big patchset of USB and PHY driver updates for 4.13-rc1.
On the PHY side, they decided to move files around to "make things
easier" in their tree. Hopefully that wasn't a mistake, but in
linux-next testing, we haven't had any reported problems.
There's the usual set of gadget and xhci and musb updates in here as
well, along with a number of smaller updates for a raft of different
USB drivers. Full details in the shortlog, nothing really major.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (173 commits)
Add USB quirk for HVR-950q to avoid intermittent device resets
USB hub_probe: rework ugly goto-into-compound-statement
usb: host: ohci-pxa27x: Handle return value of clk_prepare_enable
USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
usbip: Fix uninitialized variable bug in vhci
usb: core: read USB ports from DT in the usbport LED trigger driver
dt-bindings: leds: document new trigger-sources property
usb: typec: ucsi: Add ACPI driver
usb: typec: Add support for UCSI interface
usb: musb: compress return logic into one line
USB: serial: propagate late probe errors
USB: serial: refactor port endpoint setup
usb: musb: tusb6010_omap: Convert to DMAengine API
ARM: OMAP2+: DMA: Add slave map entries for 24xx external request lines
usb: musb: tusb6010: Handle DMA TX completion in DMA callback as well
usb: musb: tusb6010_omap: Allocate DMA channels upfront
usb: musb: tusb6010_omap: Create new struct for DMA data/parameters
usb: musb: tusb6010_omap: Use one musb_ep_select call in tusb_omap_dma_program
usb: musb: tusb6010: Add MUSB_G_NO_SKB_RESERVE to quirks
usb: musb: Add quirk to avoid skb reserve in gadget mode
...
|
|
Pull uuid subsystem from Christoph Hellwig:
"This is the new uuid subsystem, in which Amir, Andy and I have started
consolidating our uuid/guid helpers and improving the types used for
them. Note that various other subsystems have pulled in this tree, so
I'd like it to go in early.
UUID/GUID summary:
- introduce the new uuid_t/guid_t types that are going to replace the
somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS and
libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)"
* tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid: (34 commits)
ACPI: hns_dsaf_acpi_dsm_guid can be static
mmc: sdhci-pci: make guid intel_dsm_guid static
uuid: Take const on input of uuid_is_null() and guid_is_null()
thermal: int340x_thermal: fix compile after the UUID API switch
thermal: int340x_thermal: Switch to use new generic UUID API
acpi: always include uuid.h
ACPI: Switch to use generic guid_t in acpi_evaluate_dsm()
ACPI / extlog: Switch to use new generic UUID API
ACPI / bus: Switch to use new generic UUID API
ACPI / APEI: Switch to use new generic UUID API
acpi, nfit: Switch to use new generic UUID API
MAINTAINERS: add uuid entry
tmpfs: generate random sb->s_uuid
scsi_debug: switch to uuid_t
nvme: switch to uuid_t
sysctl: switch to use uuid_t
partitions/ldm: switch to use uuid_t
overlayfs: use uuid_t instead of uuid_be
fs: switch ->s_uuid to uuid_t
ima/policy: switch to use uuid_t
...
|
|
* acpi-pm:
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
ACPI / sleep: EC-based wakeup from suspend-to-idle on recent systems
platform: x86: intel-hid: Wake up the system from suspend-to-idle
platform: x86: intel-vbtn: Wake up the system from suspend-to-idle
ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle
platform/x86: Add driver for ACPI INT0002 Virtual GPIO device
PCI / PM: Restore PME Enable if skipping wakeup setup
PM / sleep: Print timing information if debug is enabled
ACPI / PM: Clean up device wakeup enable/disable code
ACPI / PM: Change log level of wakeup-related message
USB / PCI / PM: Allow the PCI core to do the resume cleanup
ACPI / PM: Run wakeup notify handlers synchronously
Conflicts:
drivers/base/power/main.c
|
|
Merge 'uuid-types' from git://git.infradead.org/users/hch/uuid.git
|
|
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The run_wake flag in struct dev_pm_info is used to indicate whether
or not the device is capable of generating remote wakeup signals at
run time (or in the system working state), but the distinction
between runtime remote wakeup and system wakeup signaling has always
been rather artificial. The only practical reason for it to exist
at the core level was that ACPI and PCI treated those two cases
differently, but that's not the case any more after recent changes.
For this reason, get rid of the run_wake flag and, when applicable,
use device_set_wakeup_capable() and device_can_wakeup() instead of
device_set_run_wake() and device_run_wake(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
For AMD Promontory xHCI host, although you can disable USB 2.0 ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
This will disable wake on connect, disconnect and overcurrent on
AMD Promontory USB2 ports
[checkpatch cleanup and commit message reword -Mathias]
Cc: <stable@vger.kernel.org>
Cc: Tsai Nicholas <nicholas.tsai@amd.com>
Signed-off-by: Jiahau Chang <Lars_Chang@asmedia.com.tw>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the USB fixes in here.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
finish_td() could be called with a skip option to bypass most of the
function and only call xhci_td_cleanup() at the end.
Remove this skip option and call xhci_td_cleanup() directly instead
when needed
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Get rid of stopped_stream member in virtual endpoint structure as
it is only used in one case when cleaning a halted endpoint.
Pass it as function parameter instead.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Most transfer events have a TRB pointer indicating which TRB caused
the event.
In the case of streams, transfer events such as
USB Transaction error may have its TRB pointer set to zero.
driver won't know which stream or what TRB on that stream caused
the error, but it can issue a soft reset to recover the transfer.
A soft reset will clear the host side halt of the endpoint without
clearing Data toggle or sequence number, and let the transfer
continue from where it halted.
see xhci section 4.12 streams and 4.6.8.2 soft retry.
USB Transaction errors with a zero TRB pointer are seen with
UAS usb devices.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add soft reset support to cleanup_halted_endpoint().
using soft reset will prevent it from setting a new dequeue pointer to
start the transfer from. Let it continue where it halted.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci supports soft retry recovery when the host halted the host side of an
endopint but the connected USB device is not aware of the halt.
In this case xhci needs to issue a reset endopint command with a TSP
(Transfer State Preserve) flag set which preserves the Data toggle
and Sequence number of the endpoint.
This feature is needed to handle a few special transfer event types
such as USB Transaction error that don't always point to a causing TRB.
see xhci 4.6.8.1 for more details
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Parse the transfer event first, and remove duplicate debugging
code.
Reorder completion codes according to endpoint state.
No functional changes
We are not handling some transfer events correcly and need to
clean up this before fixing it
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Anurag Kumar Vulisha reported several issues with xhci endpoint
ring caching.
31 Rings are cached per device before a ring is freed.
These cached rings are not used as default if a new ring is needed.
They are only used if the driver fails to allocate memory for a ring.
The current ring cache is more a reason to why we run out memory than a
help when we actually do so.
Anurag Kumar Vulisha tried to use cached rings as a first option and
found new issues with cached ring initialization.
Cached rings were first zeroed and then manually reinitialized with link
trbs etc, but forgetting to set some important bits like cycle toggle bit.
Remove the ring cache completely as it's a faulty premature optimization
eating memory
Reported-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Tested-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When plugging an USB webcam I see the following message:
[106385.615559] xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[106390.583860] handle_tx_event: 913 callbacks suppressed
With this patch applied, I get no more printing of this message.
Cc: <stable@vger.kernel.org>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xHCI host controllers can have both USB 3.1 and 3.0 extended speed
protocol lists. If the USB3.1 speed is parsed first and 3.0 second then
the minor revision supported will be overwritten by the 3.0 speeds and
the USB3 roothub will only show support for USB 3.0 speeds.
This was the case with a xhci controller with the supported protocol
capability listed below.
In xhci-mem.c, the USB 3.1 speed is parsed first, the min_rev of usb3_rhub
is set as 0x10. And then USB 3.0 is parsed. However, the min_rev of
usb3_rhub will be changed to 0x00. If USB 3.1 device is connected behind
this host controller, the speed of USB 3.1 device just reports 5G speed
using lsusb.
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
00 01 08 00 00 00 00 00 40 00 00 00 00 00 00 00 00
10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20 02 08 10 03 55 53 42 20 01 02 00 00 00 00 00 00 //USB 3.1
30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40 02 08 00 03 55 53 42 20 03 06 00 00 00 00 00 00 //USB 3.0
50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60 02 08 00 02 55 53 42 20 09 0E 19 00 00 00 00 00 //USB 2.0
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
This patch fixes the issue by only owerwriting the minor revision if
it is higher than the existing one.
[reword commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: YD Tseng <yd_tseng@asmedia.com.tw>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This driver is no longer needed and can be removed. The reason why
it's safe to remove this driver is that most omap devices don't have a
USB low-speed or full-speed compatible PHY installed and configured
with drivers/mfd/omap-usb-host.c. This means that devices like
beagleboard and pandaboard need to use a high-speed USB hub in order
to use devices like keyboard and mice.
Currently the only known configured for a full-speed PHY is the
mdm6600 modem on droid 4 and I've verified it works just fine with
ohci-platform.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With the runtime PM implemented for ohci-platform driver, we can
now support omap3 and later OHCI by adding one device tree
property.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is needed in preparation of adding support for omap3 and
later OHCI. The runtime PM will only do something on platforms
that implement it.
Cc: devicetree@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Start using ktime_* compare functions to make the code backportable.
Now that may be a bit tricky due to recent change of ktime_t.
Signed-off-by: Mariusz Skamra <mariuszx.skamra@intel.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add xhci_get_hw_deq() helper to retrieve the hardware dequeue pointer an
endpoint or stream stopped on.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The values for the new dequeue segment, new dequeue pointer and new cycle
state are needed for manually moving the xHC ring dequeue pointer.
These are conveniently stored in a xhci_dequeue_state structure.
stream support was added later and stream_id was carried
as a function parameter.
Move the stream_id to the xhci_dequeue_state structure instead.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When xHC is asked to stop an endpoint it will save the position it
stopped on in the endpoint or stream context.
xhci driver needs to know if the controller stopped on the exact same
TRB that the driver was asked to cancel as it then needs to move past
the TD instead of turning the TD to no-op TRBs.
xhci driver used to get the stopped position from a "stopped" transfer
event before the stop endpoint command completed, but if the ring
is already stopped, or in a halted or error state this event is missing.
Get the stopped position from the endpoint or stream context instead
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We no longer keep track of where we stopped in a stopped_td pointer.
We get the ring dequeue pointer from the endpoint or stream context
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Aspeed 2400/2500 families have a variant of UHCI which requires
some quirks to the driver to work:
- The register offsets are different. We add a remapping helper.
- All accesses have to be done via 32-bit loads and stores. We
force all accessors to use readl/writel. This is of no consequence
for reads as we never read "in the middle" of a register. For writes
it also works fine as the registers only actually implement the bits
we try to write (16-bit for the registers accessed with writew and
8-bit for the register accessed with writeb), so always using a
32-bit write will have no negative effect. We never do partial writes.
- The resume detect interrupt is broken
- The number of ports is (optionally) provided via the device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
--
v2. Remove the bulk of the #ifdef's
drivers/usb/host/Kconfig | 6 ++++-
drivers/usb/host/uhci-hcd.c | 17 +++++++++++---
drivers/usb/host/uhci-hcd.h | 51 ++++++++++++++++++++++++++++++++++++++++
drivers/usb/host/uhci-platform.c | 22 ++++++++++++++++-
4 files changed, 91 insertions(+), 5 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the USB fixes in here as well to handle testing and merge
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() returns an error code, but the xhci-plat driver
ignores it and always returns -ENODEV. This is not correct, and
prevents -EPROBE_DEFER from being propagated properly.
CC: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In 4.11 TRB completion codes were renamed to match spec.
Completion codes for command ring stopped and endpoint stopped
were mixed, leading to failures while handling a stopped command ring.
Use the correct completion code for command ring stopped events.
Fixes: 0b7c105a04ca ("usb: host: xhci: rename completion codes to match spec")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no reason to restrict allocations to the first 16MB ISA DMA
addresses.
It is causing problems in a virtualization setup with enabled IOMMU
(x86_64). The result is that USB is not working in the VM.
CC: <stable@vger.kernel.org>
Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With threaded interrupts, bottom-half handlers are called with
interrupts enabled. Therefore they can't safely use spin_lock(); they
have to use spin_lock_irqsave(). Lockdep warns about a violation
occurring in xhci_irq():
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
4.11.0-rc8-dbg+ #1 Not tainted
---------------------------------------------------------
swapper/7/0 just changed the state of lock:
(&(&ehci->lock)->rlock){-.-...}, at: [<ffffffffa0130a69>]
ehci_hrtimer_func+0x29/0xc0 [ehci_hcd]
but this lock took another, HARDIRQ-unsafe lock in the past:
(hcd_urb_list_lock){+.....}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(hcd_urb_list_lock);
local_irq_disable();
lock(&(&ehci->lock)->rlock);
lock(hcd_urb_list_lock);
<Interrupt>
lock(&(&ehci->lock)->rlock);
*** DEADLOCK ***
no locks held by swapper/7/0.
the shortest dependencies between 2nd lock and 1st lock:
-> (hcd_urb_list_lock){+.....} ops: 252 {
HARDIRQ-ON-W at:
__lock_acquire+0x602/0x1280
lock_acquire+0xd5/0x1c0
_raw_spin_lock+0x2f/0x40
usb_hcd_unlink_urb_from_ep+0x1b/0x60 [usbcore]
xhci_giveback_urb_in_irq.isra.45+0x70/0x1b0 [xhci_hcd]
finish_td.constprop.60+0x1d8/0x2e0 [xhci_hcd]
xhci_irq+0xdd6/0x1fa0 [xhci_hcd]
usb_hcd_irq+0x26/0x40 [usbcore]
irq_forced_thread_fn+0x2f/0x70
irq_thread+0x149/0x1d0
kthread+0x113/0x150
ret_from_fork+0x2e/0x40
This patch fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Bart Van Assche <bart.vanassche@sandisk.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to xHCI spec Figure 30: Interrupt Throttle Flow Diagram
If PCI Message Signaled Interrupts (MSI or MSI-X) are enabled,
then the assertion of the Interrupt Pending (IP) flag in Figure 30
generates a PCI Dword write. The IP flag is automatically cleared
by the completion of the PCI write.
the MSI enabled HCs don't need to clear interrupt pending bit, but
hcd->irq = 0 doesn't equal to MSI enabled HCD. At some Dual-role
controller software designs, it sets hcd->irq as 0 to avoid HCD
requesting interrupt, and they want to decide when to call usb_hcd_irq
by software.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to xHCI ch4.20 Scratchpad Buffers, the Scratchpad
Buffer needs to be zeroed.
...
The following operations take place to allocate
Scratchpad Buffers to the xHC:
...
b. Software clears the Scratchpad Buffer to '0'
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel Denverton microserver is Atom based and need the PME and CAS quirks
as well.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't access any members of a URB after giving it back.
URB might be freed by then already.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove unnecessary null check. udev->tt cannot ever be NULL when this
section of code runs.
Addresses-Coverity-ID: 100828
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the new define for the maximum number of SuperSpeed ports instead of
a constant when allocating xHCI root hubs.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure do drop the reference taken to the companion device during
resume.
Fixes: d4d75128b8fd ("usb: host: ehci-platform: fix usb 1.1 device is not connected in system resume")
Cc: stable <stable@vger.kernel.org> # 4.11
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If multiple endpoints on a single device have pending IN URBs and one
endpoint times out due to NAKs (perfectly legal), select a different
endpoint URB to try.
The existing code only checked to see another device address has pending
URBs and ignores other IN endpoints on the current device address. This
leads to endpoints never getting serviced if one endpoint is using NAK as
a flow control method.
Fixes: 5d3043586db4 ("usb: r8a66597-hcd: host controller driver for R8A6659")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The timeout for BULK packets was 300ms which is a long time if other
endpoints or devices are waiting for their turn. Changing it to 50ms
greatly increased the overall performance for multi-endpoint devices.
Fixes: 5d3043586db4 ("usb: r8a66597-hcd: host controller driver for R8A6659")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The #ifdef is slightly wrong as it doesn't cover the xhci_priv_resume_quirk()
function, causing a harmless warning:
drivers/usb/host/xhci-plat.c:58:12: error: 'xhci_priv_resume_quirk' defined but not used [-Werror=unused-function]
static int xhci_priv_resume_quirk(struct usb_hcd *hcd)
A simpler way to do this correctly is to use __maybe_unused annotations
that let the compiler silently drop the functions when there is no
reference.
Fixes: b0c69b4bace3 ("usb: host: plat: Enable xHCI plat runtime PM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Print correct command ring address using 'val_64'.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We already have sp_array to store each scratch buffer address for xHC,
it doesn't need another sp_dma_buffers array to store it.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Using correct specification chapter reference for DCBAAP
(Device Context Base Address Array Pointer).
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the modern API to request MSI or MSI-X interrupts, which allows us to
get rid of the msix_entries array, as well as cleaning up the cleanup
code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch sets resume_quirk() for R-Car controllers to re-download
the firmware in resume timing. Otherwise, if the controller's power
is down in suspend timing, the firmware in the controller goes away,
and then the controller doesn't work after resume.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
