summaryrefslogtreecommitdiff
path: root/drivers/usb/host/ohci.h
AgeCommit message (Collapse)Author
2010-10-22OHCI: work around for nVidia shutdown problemAlan Stern
This patch (as1417) fixes a problem affecting some (or all) nVidia chipsets. When the computer is shut down, the OHCI controllers continue to power the USB buses and evidently they drive a Reset signal out all their ports. This prevents attached devices from going to low power. Mouse LEDs stay on, for example, which is disconcerting for users and a drain on laptop batteries. The fix involves leaving each OHCI controller in the OPERATIONAL state during system shutdown rather than putting it in the RESET state. Although this nominally means the controller is running, in fact it's not doing very much since all the schedules are all disabled. However there is ongoing DMA to the Host Controller Communications Area, so the patch also disables the bus-master capability of all PCI USB controllers after the shutdown routine runs. The fix is applied only to nVidia-based PCI OHCI controllers, so it shouldn't cause problems on systems using other hardware. As an added safety measure, in case the kernel encounters one of these running controllers during boot, the patch changes quirk_usb_handoff_ohci() (which runs early on during PCI discovery) to reset the controller before anything bad can happen. Reported-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: David Brownell <david-b@pacbell.net> Tested-by: Pali Rohár <pali.rohar@gmail.com> CC: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-11-17USB: ohci: quirk AMD prefetch for USB 1.1 ISO transferLibin Yang
The following patch in the driver is required to avoid USB 1.1 device failures that may occur due to requests from USB OHCI controllers may be overwritten if the latency for any pending request by the USB controller is very long (in the range of milliseconds). Signed-off-by: Libin Yang <libin.yang@amd.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-17usb: remove code associated with !CONFIG_PPC_MERGEKumar Gala
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore remove the dead code associated with !CONFIG_PPC_MERGE. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-08-13USB: quirk PLL power down modeLibin Yang
On some AMD 700 series southbridges, ISO OUT transfers (such as audio playback through speakers) on the USB OHCI controller may be corrupted when an A-Link express power saving feature is active. PLL power down mode in conjunction with link power management feature L1 being enabled is the bad combination ... this patch prevents them from being enabled when ISO transfers are pending. Signed-off-by: Crane Cai <crane.cai@amd.com> Signed-off-by: Libin Yang <libin.yang@amd.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-08-13USB: Hook start_hnp into ohci structDmitry Baryshkov
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-08-13USB: ohci: make distrust_firmware a quirkDmitry Baryshkov
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01USB: convert ohci debug files to use debugfs instead of sysfsTony Jones
We should not have multiple line files in sysfs, this moves the data to debugfs instead, like the UHCI driver. Signed-off-by: Tony Jones <tonyj@suse.de> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12USB: add runtime frame_no quirk for big-endian OHCIValentine Barshak
Add OHCI big endian frame_no quirk. The frame_no value stored in the HCCA is a 16 bit field at a specific offset, but since not all CPUs can do 16-bit memory accesses it's used as a 32 bit field. And that's why big-endian OHCI must shift 16 bits ... unless the spec is not followed. Currently there's one MPC52xx platform that doesn't need the shift. This patch adds a new "big endian frame_no" quirk to control that at runtime. Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com> Acked-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12USB: OHCI handles more ZFMicro quirksMike Nuss
The ZF Micro OHCI controller exhibits unexpected behavior that seems to be related to high load. Under certain conditions, the controller will complete a TD, remove it from the endpoint's queue, and fail to add it to the donelist. This causes the endpoint to appear to stop responding. Worse, if the device is removed while in that state, OHCI will hang while waiting for the orphaned TD to complete. The situation is not recoverable without rebooting. This fix enhances the scope of the existing OHCI_QUIRK_ZFMICRO flag: 1. A watchdog routine periodically scans the OHCI structures to check for orphaned TDs. In these cases the TD is taken back from the controller and completed normally. 2. If a device is removed while the endpoint is hung but before the watchdog catches the situation, any outstanding TDs are taken back from the controller in the 'sanitize' phase. The ohci-hcd driver used to print "INTR_SF lossage" in this situation; this changes it to the universally accurate "ED unlink timeout". Other instances of this message presumably have different root causes. Both this Compaq quirk and a NEC quirk are now properly compiled out for non-PCI builds of this driver. Signed-off-by: Mike Nuss <mike@terascala.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12USB: Fix NEC OHCI chip silicon bugMichael Hanselmann
This patch fixes a silicon bug in some NEC OHCI chips. The bug appears at random times and is very, very difficult to reproduce. Without the following patch, Linux would shut the chip and its associated devices down. In Apple PowerBooks this leads to an unusable keyboard and mouse (SSH still working). The idea of restarting the chip is taken from public Darwin code. Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-09[PATCH] hci_{read,write}l() does force casts to wrong type for no reasonAl Viro
readl() et.al. expect iomem pointer, so WTF force-cast it to normal one??? Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-07USB: Fix OHCI warningBenjamin Herrenschmidt
This patch fixes a warning introduces by the split endian OHCI support patch on platforms that don't have readl_be/writel_be variants (though mostly harmless as those are called in an if (0) statement, but gcc still warns). Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07USB: Implement support for "split" endian OHCIBenjamin Herrenschmidt
This patch separates support for big endian MMIO register access and big endian descriptors in order to support the Toshiba SCC implementation which has big endian registers but little endian in-memory descriptors. It simplifies the access functions a bit in ohci.h while at it. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20USB: ohci whitespace/comment fixupsDavid Brownell
This is an OHCI cleanup patch ... it removes a lot of erroneous whitespace (space before tab, at end of line) as well as the obsolete inline changelog. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20USB: fix ohci.h over-use warningsJeff Garzik
When u132-hcd is built, it includes local header ohci.h, which appears to have been intended only for use by ohci-hcd. This throws warnings about functions which are defined and not used. The warnings thrown are because three small functions are implemented in the header, but not declared 'inline', a rather strange affair. Since these functions are small, let's go ahead and define them as 'inline', just like the inline functions surrounding them. This makes things more consistent, and kills the warnings. Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-28OHCI: add auto-stop supportAlan Stern
This patch (as790b) adds "autostop" support to ohci-hcd: the driver will automatically stop the host controller when no devices have been connected for at least one second. This feature is useful when the USB autosuspend facility isn't available, such as when CONFIG_USB_SUSPEND hasn't been set. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27USB: Dealias -110 code (more complete)Pete Zaitcev
The purpose of this patch is to split off the case when a device does not reply on the lower level (which is reported by HC hardware), and a case when the device accepted the request, but does not reply at upper level. This redefinition allows to diagnose issues easier, without asking the user if the -110 happened "immediately". The usbmon splits such cases already thanks to its timestamp, but it's not always available. I adjusted all drivers which I found affected (by searching for "urb"). Out of tree drivers may suffer a little bit, but I do not expect much breakage. At worst they may print a few messages. Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27USB: Properly unregister reboot notifier in case of failure in ehci hcdAleksey Gorelov
If some problem occurs during ehci startup, for instance, request_irq fails, echi hcd driver tries it best to cleanup, but fails to unregister reboot notifier, which in turn leads to crash on reboot/poweroff. The following patch resolves this problem by not using reboot notifiers anymore, but instead making ehci/ohci driver get its own shutdown method. For PCI, it is done through pci glue, for everything else through platform driver glue. One downside: sa1111 does not use platform driver stuff, and does not have its own shutdown hook, so no 'shutdown' is called for it now. I'm not sure if it is really necessary on that platform, though. Signed-off-by: Aleks Gorelov <dared1st@yahoo.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-10-28[PATCH] OHCI PM updatesDavid Brownell
This simplifies the OHCI root hub suspend logic: - Uses new usbcore root hub calls to make autosuspend work again: * Uses a newish usbcore root hub wakeup mechanism, making requests to khubd not keventd. * Uses an even newer sibling suspend hook. - Expect someone always made usbcore call ohci_hub_suspend() before bus glue fires; and that ohci_hub_resume() is only called after that bus glue ran. Previously, only CONFIG_USB_SUSPEND promised those things. (Includes updates to PCI and OMAP bus glue.) - Handle a not-noticed-before special case during resume from one of the swsusp snapshots when using "usb-handoff": the controller isn't left in RESET state. (A bug to fix in the usb-handoff code...) Also cleans up a minor debug printk glitch, and switches an mdelay over to an msleep (how did that stick around for so long?). Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> drivers/usb/host/ohci-dbg.c | 4 ---- drivers/usb/host/ohci-hcd.c | 2 +- drivers/usb/host/ohci-hub.c | 42 ++++++++++++------------------------------ drivers/usb/host/ohci-mem.c | 1 - drivers/usb/host/ohci-omap.c | 36 ++++++++++++------------------------ drivers/usb/host/ohci-pci.c | 40 ++++++++-------------------------------- drivers/usb/host/ohci.h | 1 - 7 files changed, 33 insertions(+), 93 deletions(-)
2005-09-12[PATCH] USB: OHCI relies less on NDP registerDavid Brownell
Some OHCI implementations have differences in the way the NDP register (in roothub_a) reports the number of ports present. This patch allows the platform specific code to optionally supply the number of ports. The driver just reads the value at init (if not supplied) instead of reading it every time its needed (except for an AMD756 bug workaround). It also sets the value correctly for the ARM pxa27x architecture. Signed-Off-By: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-06-27[PATCH] ohci-omap, sl811, dummy: remove hub_set_power_budgetAlan Stern
This patch changes the HCDs that used the old hub_set_power_budget call, making them use the new hcd->power_budget field instead. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-06-27[PATCH] USB: add reboot notifier to ohciDavid Brownell
Adds a reboot notifier to OHCI, mostly to benefit kexec; plus minor #include tweaks. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] USB: OHCI on Compaq Aramada 7400David Brownell
This adds a quirk to the OHCI driver that lets it work with an old Compaq implementation. It also removes some needless strings from the non-debug version of the driver. Signed-off-by: Chris Clayton <chris_clayton@f1internet.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-16Linux-2.6.12-rc2Linus Torvalds
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!