summaryrefslogtreecommitdiff
path: root/drivers/usb/core
AgeCommit message (Collapse)Author
2014-09-29usb: rename phy to usb_phy in HCDAntoine Tenart
The USB PHY member of the HCD structure is renamed to 'usb_phy' and modifications are done in all drivers accessing it. This is in preparation to adding the generic PHY support. Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> [Sergei: added missing 'drivers/usb/misc/lvstest.c' file, resolved rejects, updated changelog.] Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-29usb: core: return -ENOTSUPP for all targeted hostsPeter Chen
The current code only returns -ENOTSUPP for OTG host, but in fact, embedded host also needs to returns -ENOTSUPP if the peripheral is not at TPL. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-28usb: core: log higher level message on malformed LANGID descriptorScot Doyle
Commit 0cce2eda19923e5e5ccc8b042dec5af87b3ffad0 USB: fix LANGID=0 regression defaults to a langid of 0x0409 if it's not properly implemented by the device. Explain with a higher level error message what this means. Signed-off-by: Scot Doyle <lkml14@scotdoyle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-25usb: Add LED triggers for USB activityMichal Sojka
With this patch, USB activity can be signaled by blinking a LED. There are two triggers, one for activity on USB host and one for USB gadget. Both triggers should work with all host/device controllers. Tested only with musb. Performace: I measured performance overheads on ARM Cortex-A8 (TI AM335x) running on 600 MHz. Duration of usb_led_activity(): - with no LED attached to the trigger: 2 ± 1 µs - with one GPIO LED attached to the trigger: 2 ± 1 µs or 8 ± 2 µs (two peaks in histogram) Duration of functions calling usb_led_activity() (with this patch applied and no LED attached to the trigger): - __usb_hcd_giveback_urb(): 10 - 25 µs - usb_gadget_giveback_request(): 2 - 6 µs Signed-off-by: Michal Sojka <sojka@merica.cz> Acked-by: Felipe Balbi <balbi@ti.com> Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23usb: hub: allow to process more usb hub events in parallelPetr Mladek
It seems that only choose_devnum() was not ready to process more hub events at the same time. All should be fine if we take bus->usb_address0_mutex there. It will make sure that more devnums will not be chosen for the given bus and the related devices at the same time. Signed-off-by: Petr Mladek <pmladek@suse.cz> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23usb: hub: rename khubd to hub_wq in documentation and commentsPetr Mladek
USB hub has started to use a workqueue instead of kthread. Let's update the documentation and comments here and there. This patch mostly just replaces "khubd" with "hub_wq". There are only few exceptions where the whole sentence was updated. These more complicated changes can be found in the following files: Documentation/usb/hotplug.txt drivers/net/usb/usbnet.c drivers/usb/core/hcd.c drivers/usb/host/ohci-hcd.c drivers/usb/host/xhci.c Signed-off-by: Petr Mladek <pmladek@suse.cz> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23usb: hub: rename usb_kick_khubd() to usb_kick_hub_wq()Petr Mladek
USB hub started to use a workqueue instead of kthread. Let's make it clear from the function names. Signed-off-by: Petr Mladek <pmladek@suse.cz> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23usb: hub: convert khubd into workqueuePetr Mladek
There is no need to have separate kthread for handling USB hub events. It is more elegant to use the workqueue framework. The workqueue is allocated as freezable because the original thread was freezable as well. Also it is allocated as ordered because the code is not ready for parallel processing of hub events, see choose_devnum(). struct usb_hub is passed via the work item. Therefore we do not need hub_event_list. Also hub_thread() is not longer needed. It would call only hub_event(). The rest of the code did manipulate the kthread and it is handled by the workqueue framework now. kick_khubd is renamed to kick_hub_wq() to make the function clear. And the protection against races is done another way, see below. hub_event_lock has been removed. It cannot longer be used to protect struct usb_hub between hub_event() and hub_disconnect(). Instead we need to get hub->kref already in kick_hub_wq(). The lock is not really needed for the other scenarios as well. queue_work() returns whether it succeeded. We could revert the needed operations accordingly. This is enough to avoid duplicity and inconsistencies. Yes, the removed lock causes that there is not longer such a strong synchronization between scheduling the work and manipulating hub->disconnected. But kick_hub_wq() must never be called together with hub_disconnect() otherwise even the original code would have failed. Any callers are responsible for this. Therefore the only problem is that hub_disconnect() could be called in parallel with hub_event(). But this was possible even in the past. struct usb_hub is still guarded by hub->kref and released in hub_events() when needed. Note that the source file is still full of the obsolete "khubd" strings. Let's remove them in a follow up patch. This patch already is complex enough. Thanks a lot Alan Stern <stern@rowland.harvard.edu> for code review, many useful tips and guidance. Also thanks to Tejun Heo <tj@kernel.org> for hints how to allocate the workqueue. Signed-off-by: Petr Mladek <pmladek@suse.cz> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23usb: hub: rename hub_events() to hub_event() and handle only one event therePetr Mladek
We would like to convert khubd kthread to a workqueue. As a result hub_events() will handle only one event per call. In fact, we could do this already now because there is another cycle in hub_thread(). It calls hub_events() until hub_event_list is empty. This patch renames the function to hub_event(), removes the while cycle, and renames the goto targets from loop* to out*. When touching the code, it fixes also formatting of dev_err() and dev_dbg() calls to make checkpatch.pl happy :-) Signed-off-by: Petr Mladek <pmladek@suse.cz> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23usb: hub: keep hub->dev reference all the time when struct usb_hub livesPetr Mladek
This is just a small optimization of the fix from the commit c605f3cdff53a743f6 ("usb: hub: take hub->hdev reference when processing from eventlist). We do not need to take the reference for each event. Instead we could get it when struct usb_hub is allocated and put it when it is released. By other words, we could handle it the same way as the reference for hub->intfdev. The motivation is that it will make the life easier when switching from khubd kthread to a workqueue. Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Petr Mladek <pmladek@suse.cz> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23USB: Add device quirk for ASUS T100 Base Station keyboardLu Baolu
This full-speed USB device generates spurious remote wakeup event as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result, Linux can't enter system suspend and S0ix power saving modes once this keyboard is used. This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk. With this quirk set, wakeup capability will be ignored during device configure. This patch could be back-ported to kernels as old as 2.6.39. Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23usb: Fixed a few typosMickael Maison
Fixed typos in comments of various drivers/usb files Signed-off-by: Mickael Maison <mickael.maison@gmail.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23usb: core: Kconfig: TPL should apply for both OTG and EHPeter Chen
Update configuration for USB_OTG_WHITELIST, any targeted hosts (non PC-hosts) can have TPL (Targered Peripheral List). Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23usb: core: TPL should apply for both OTG and EHPeter Chen
According to On-The-Go and Embedded Host Supplement to the USB Revision 2.0 Specification, the targeted hosts (non-PC hosts) include both embedded hosts and otg, and each targeted host product defines the set of supported peripherals on a TPL (Targeted Peripheral List). So, TPL should apply for both OTG and embedded host, and the otg support is not a must for embedded host. The TPL support feature will only be effect when CONFIG_USB_OTG_WHITELIST has been chosen and hcd->tpl_support flag is set, it can avoid the enumeration fails problem for the user who chooses CONFIG_USB_OTG_WHITELIST wrongly. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23USB: quirks: enable device-qualifier quirk for Elan TouchscreenJohan Hovold
Enable device-qualifier quirk for Elan Touchscreen, which often fails to handle requests for the device_descriptor. Note that the device sometimes do respond properly with a Request Error (three times as USB core retries), but usually fails to respond at all. When this happens any further descriptor requests also fails, for example: [ 1528.688934] usb 2-7: new full-speed USB device number 4 using xhci_hcd [ 1530.945588] usb 2-7: unable to read config index 0 descriptor/start: -71 [ 1530.945592] usb 2-7: can't read configurations, error -71 This has been observed repeating for over a minute before eventual successful enumeration. Reported-by: Drew Von Spreecken <drewvs@gmail.com> Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23USB: core: add device-qualifier quirkJohan Hovold
Add new quirk for devices that cannot handle requests for the device_qualifier descriptor. A USB-2.0 compliant device must respond to requests for the device_qualifier descriptor (even if it's with a request error), but at least one device is known to misbehave after such a request. Suggested-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-10usb: hub: take hub->hdev reference when processing from eventlistJoe Lawrence
During surprise device hotplug removal tests, it was observed that hub_events may try to call usb_lock_device on a device that has already been freed. Protect the usb_device by taking out a reference (under the hub_event_lock) when hub_events pulls it off the list, returning the reference after hub_events is finished using it. Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com> Suggested-by: David Bulkow <david.bulkow@stratus.com> for using kref Suggested-by: Alan Stern <stern@rowland.harvard.edu> for placement Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-08-27USB: fix build error with CONFIG_PM_RUNTIME disabledGreg Kroah-Hartman
commit bdd405d2a528 ("usb: hub: Prevent hub autosuspend if usbcore.autosuspend is -1") causes a build error if CONFIG_PM_RUNTIME is disabled. Fix that by doing a simple #ifdef guard around it. Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: Roger Quadros <rogerq@ti.com> Cc: Michael Welling <mwelling@emacinc.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-08-26usb: hub: Prevent hub autosuspend if usbcore.autosuspend is -1Roger Quadros
If user specifies that USB autosuspend must be disabled by module parameter "usbcore.autosuspend=-1" then we must prevent autosuspend of USB hub devices as well. commit 596d789a211d introduced in v3.8 changed the original behaivour and stopped respecting the usbcore.autosuspend parameter for hubs. Fixes: 596d789a211d "USB: set hub's default autosuspend delay as 0" Cc: [3.8+] <stable@vger.kernel.org> Signed-off-by: Roger Quadros <rogerq@ti.com> Tested-by: Michael Welling <mwelling@emacinc.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-08-19usb: core: fix below build warningPeter Chen
linux-2.6/drivers/usb/core/hub.c: In function 'usb_disconnect': linux-2.6/drivers/usb/core/hub.c:2110: warning: 'hub' may be used uninitialized in this function linux-2.6/drivers/usb/core/hub.c:2111: warning: 'port1' may be used uninitialized in this function Signed-off-by: Peter Chen <peter.chen@freescale.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-08-19usbcore: Fix wrong device in an error message in hub_port_connect()Takashi Iwai
The commit [5ee0f803cc3a: usbcore: don't log on consecutive debounce failures of the same port] added the check of the reliable port, but it also replaced the device argument to dev_err() wrongly, which leads to a NULL dereference. This patch restores the right device, port_dev->dev. Also, since dev_err() itself shows the port number, reduce the port number shown in the error message, essentially reverting to the state before the commit 5ee0f803cc3a. [The fix suggested by Hannes, and the error message cleanup suggested by Alan Stern] Fixes: 5ee0f803cc3a ('usbcore: don't log on consecutive debounce failures of the same port') Reported-by: Hannes Reinecke <hare@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-08-04Merge tag 'usb-3.17-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB updates from Greg KH: "Here is the big USB driver update for 3.17-rc1. Loads of gadget driver changes in here, including some big file movements to make things easier to manage over time. There's also the usual xhci and uas driver updates, and a handful of other changes in here. The changelog has the full details. All of these have been in linux-next for a while" * tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (211 commits) USB: devio: fix issue with log flooding uas: Log a warning when we cannot use uas because the hcd lacks streams uas: Only complain about missing sg if all other checks succeed xhci: Add missing checks for xhci_alloc_command failure xhci: Rename Asrock P67 pci product-id to EJ168 xhci: Blacklist using streams on the Etron EJ168 controller uas: Limit qdepth to 32 when connected over usb-2 uwb/whci: use correct structure type name in sizeof usb-core bInterval quirk USB: serial: ftdi_sio: Add support for new Xsens devices USB: serial: ftdi_sio: Annotate the current Xsens PID assignments usb: chipidea: debug: fix sparse non static symbol warnings usb: ci_hdrc_imx doc: fsl,usbphy is required usb: ci_hdrc_imx: Return -EINVAL for missing USB PHY usb: core: allow zero packet flag for interrupt urbs usb: lvstest: Fix sparse warnings generated by kbuild test bot USB: core: hcd-pci: free IRQ before disabling PCI device when shutting down phy: miphy365x: Represent each PHY channel as a DT subnode phy: miphy365x: Provide support for the MiPHY356x Generic PHY phy: miphy365x: Add Device Tree bindings for the MiPHY365x ...
2014-08-01USB: devio: fix issue with log floodingOliver Neukum
usbfs allows user space to pass down an URB which sets URB_SHORT_NOT_OK for output URBs. That causes usbcore to log messages without limit for a nonsensical disallowed combination. The fix is to silently drop the attribute in usbfs. The problem is reported to exist since 3.14 https://www.virtualbox.org/ticket/13085 Signed-off-by: Oliver Neukum <oneukum@suse.de> CC: stable@vger.kernel.org Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-08-01usb-core bInterval quirkJames P Michels III
This patch adds a usb quirk to support devices with interupt endpoints and bInterval values expressed as microframes. The quirk causes the parse endpoint function to modify the reported bInterval to a standards conforming value. There is currently code in the endpoint parser that checks for bIntervals that are outside of the valid range (1-16 for USB 2+ high speed and super speed interupt endpoints). In this case, the code assumes the bInterval is being reported in 1ms frames. As well, the correction is only applied if the original bInterval value is out of the 1-16 range. With this quirk applied to the device, the bInterval will be accurately adjusted from microframes to an exponent. Signed-off-by: James P Michels III <james.p.michels@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-22usb: core: allow zero packet flag for interrupt urbsAmit Virdi
Section 4.4.7.2 "Interrupt Transfer Bandwidth Requirements" of the USB3.0 spec says: A zero-length data payload is a valid transfer and may be useful for some implementations. So, extend the logic of allowing URB_ZERO_PACKET to interrupt urbs too. Otherwise, the kernel throws warning of BOGUS transfer flags. Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-22USB: core: hcd-pci: free IRQ before disabling PCI device when shutting downJiang Liu
The assigned IRQ should be freed before calling pci_disable_device() when shutting down system, otherwise it will cause following warning. [ 568.879482] ------------[ cut here ]------------ [ 568.884236] WARNING: CPU: 1 PID: 3300 at /home/konrad/ssd/konrad/xtt-i386/bootstrap/linux-usb/fs/proc/generic.c:521 remove_proc_entry+0x165/0x170() [ 568.897846] remove_proc_entry: removing non-empty directory 'irq/16', leaking at least 'ohci_hcd:usb4' [ 568.907430] Modules linked in: dm_multipath dm_mod iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi libcrc32c crc32c_generic sg sd_mod crct10dif_generic crc_t10dif crct10dif_common radeon fbcon tileblit ttm font bitblit softcursor ata_generic ahci libahci drm_kms_helper skge r8169 libata mii scsi_mod wmi acpi_cpufreq [ 568.938539] CPU: 1 PID: 3300 Comm: init Tainted: G W 3.16.0-rc5upstream-01651-g03b9189 #1 [ 568.947946] Hardware name: ECS A780GM-A Ultra/A780GM-A Ultra, BIOS 080015 04/01/2010 [ 568.956008] 00000209 ed0f1cd0 c1617946 c175403c ed0f1d00 c1090c3f c1754084 ed0f1d2c [ 568.964068] 00000ce4 c175403c 00000209 c11f22a5 c11f22a5 f755e8c0 ed0f1d78 f755e90d [ 568.972128] ed0f1d18 c1090cde 00000009 ed0f1d10 c1754084 ed0f1d2c ed0f1d60 c11f22a5 [ 568.980194] Call Trace: [ 568.982715] [<c1617946>] dump_stack+0x48/0x60 [ 568.987294] [<c1090c3f>] warn_slowpath_common+0x7f/0xa0 [ 569.003887] [<c1090cde>] warn_slowpath_fmt+0x2e/0x30 [ 569.009092] [<c11f22a5>] remove_proc_entry+0x165/0x170 [ 569.014476] [<c10da6ca>] unregister_irq_proc+0xaa/0xc0 [ 569.019858] [<c10d582f>] free_desc+0x1f/0x60 [ 569.024346] [<c10d58aa>] irq_free_descs+0x3a/0x80 [ 569.029283] [<c10d9e9d>] irq_dispose_mapping+0x2d/0x50 [ 569.034666] [<c1078fd3>] mp_unmap_irq+0x73/0xa0 [ 569.039423] [<c107196b>] acpi_unregister_gsi_ioapic+0x2b/0x40 [ 569.045431] [<c107180f>] acpi_unregister_gsi+0xf/0x20 [ 569.050725] [<c1339cad>] acpi_pci_irq_disable+0x4b/0x50 [ 569.056196] [<c14daa38>] pcibios_disable_device+0x18/0x20 [ 569.061848] [<c130123d>] do_pci_disable_device+0x4d/0x60 [ 569.067410] [<c13012b7>] pci_disable_device+0x47/0xb0 [ 569.077814] [<c14800b1>] usb_hcd_pci_shutdown+0x31/0x40 [ 569.083285] [<c1304b19>] pci_device_shutdown+0x19/0x50 [ 569.088667] [<c13fda64>] device_shutdown+0x14/0x120 [ 569.093777] [<c10ac29d>] kernel_restart_prepare+0x2d/0x30 [ 569.099429] [<c10ac41e>] kernel_restart+0xe/0x60 [ 569.109028] [<c10ac611>] SYSC_reboot+0x191/0x220 [ 569.159269] [<c10ac6ba>] SyS_reboot+0x1a/0x20 [ 569.163843] [<c161c718>] sysenter_do_call+0x12/0x16 [ 569.168951] ---[ end trace ccc1ec4471c289c9 ]--- Tested-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-18USB: Fix persist resume of some SS USB devicesPratyush Anand
Problem Summary: Problem has been observed generally with PM states where VBUS goes off during suspend. There are some SS USB devices which take longer time for link training compared to many others. Such devices fail to reconnect with same old address which was associated with it before suspend. When system resumes, at some point of time (dpm_run_callback-> usb_dev_resume->usb_resume->usb_resume_both->usb_resume_device-> usb_port_resume) SW reads hub status. If device is present, then it finishes port resume and re-enumerates device with same address. If device is not present then, SW thinks that device was removed during suspend and therefore does logical disconnection and removes all the resource allocated for this device. Now, if I put sufficient delay just before root hub status read in usb_resume_device then, SW sees always that device is present. In normal course(without any delay) SW sees that no device is present and then SW removes all resource associated with the device at this port. In the latter case, after sometime, device says that hey I am here, now host enumerates it, but with new address. Problem had been reproduced when I connect verbatim USB3.0 hard disc with my STiH407 XHCI host running with 3.10 kernel. I see that similar problem has been reported here. https://bugzilla.kernel.org/show_bug.cgi?id=53211 Reading above it seems that bug was not in 3.6.6 and was present in 3.8 and again it was not present for some in 3.12.6, while it was present for few others. I tested with 3.13-FC19 running at i686 desktop, problem was still there. However, I was failed to reproduce it with 3.16-RC4 running at same i686 machine. I would say it is just a random observation. Problem for few devices is always there, as I am unable to find a proper fix for the issue. So, now question is what should be the amount of delay so that host is always able to recognize suspended device after resume. XHCI specs 4.19.4 says that when Link training is successful, port sets CSC bit to 1. So if SW reads port status before successful link training, then it will not find device to be present. USB Analyzer log with such buggy devices show that in some cases device switch on the RX termination after long delay of host enabling the VBUS. In few other cases it has been seen that device fails to negotiate link training in first attempt. It has been reported till now that few devices take as long as 2000 ms to train the link after host enabling its VBUS and RX termination. This patch implements a 2000 ms timeout for CSC bit to set ie for link training. If in a case link trains before timeout, loop will exit earlier. This patch implements above delay, but only for SS device and when persist is enabled. So, for the good device overhead is almost none. While for the bad devices penalty could be the time which it take for link training. But, If a device was connected before suspend, and was removed while system was asleep, then the penalty would be the timeout ie 2000 ms. Results: Verbatim USB SS hard disk connected with STiH407 USB host running 3.10 Kernel resumes in 461 msecs without this patch, but hard disk is assigned a new device address. Same system resumes in 790 msecs with this patch, but with old device address. Cc: <stable@vger.kernel.org> Signed-off-by: Pratyush Anand <pratyush.anand@st.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-18usb-core: Remove Fix mes in file hcd.cNicholas Krause
I am removing two fix mes in this file as after dicussing then it seems there is no reason to check against Null for usb_device as it can never be NULL and this is check is therefore not needed. Signed-off-by: Nicholas Krause <xerofoify@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-18usbcore: don't log on consecutive debounce failures of the same portOliver Neukum
Some laptops have an internal port for a BT device which picks up noise when the kill switch is used, but not enough to trigger printk_rlimit(). So we shouldn't log consecutive faults of this kind. Signed-off-by: Oliver Neukum <oneukum@suse.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17usb: Check if port status is equal to RxDetectGavin Guo
When using USB 3.0 pen drive with the [AMD] FCH USB XHCI Controller [1022:7814], the second hotplugging will experience the USB 3.0 pen drive is recognized as high-speed device. After bisecting the kernel, I found the commit number 41e7e056cdc662f704fa9262e5c6e213b4ab45dd (USB: Allow USB 3.0 ports to be disabled.) causes the bug. After doing some experiments, the bug can be fixed by avoiding executing the function hub_usb3_port_disable(). Because the port status with [AMD] FCH USB XHCI Controlleris [1022:7814] is already in RxDetect (I tried printing out the port status before setting to Disabled state), it's reasonable to check the port status before really executing hub_usb3_port_disable(). Fixes: 41e7e056cdc6 (USB: Allow USB 3.0 ports to be disabled.) Signed-off-by: Gavin Guo <gavin.guo@canonical.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17USB: Add EXPORT_SYMBOL for usb_alloc_devPratyush Anand
usb_alloc_dev is used by lvstest driver now which can be built as module. Therefore export usb_alloc_dev symbol. Signed-off-by: Pratyush Anand <pratyush.anand@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17USB: shutdown all URBs after controller deathAlan Stern
When a host controller dies, we don't need to wait for a driver to time out. We can shut down its URBs immediately. Without this change, we can end up waiting 30 seconds for a mass-storage transfer to time out. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-11USB: add reset resume quirk for usb3503Joonyoung Shim
The usb device will autoresume from choose_wakeup() if it is autosuspended with the wrong wakeup setting, but below errors occur because usb3503 misc driver will switch to standby mode when suspended. As add USB_QUIRK_RESET_RESUME, it can stop setting wrong wakeup from autosuspend_check(). [ 7.734717] usb 1-3: reset high-speed USB device number 3 using exynos-ehci [ 7.854658] usb 1-3: device descriptor read/64, error -71 [ 8.079657] usb 1-3: device descriptor read/64, error -71 [ 8.294664] usb 1-3: reset high-speed USB device number 3 using exynos-ehci [ 8.414658] usb 1-3: device descriptor read/64, error -71 [ 8.639657] usb 1-3: device descriptor read/64, error -71 [ 8.854667] usb 1-3: reset high-speed USB device number 3 using exynos-ehci [ 9.264598] usb 1-3: device not accepting address 3, error -71 [ 9.374655] usb 1-3: reset high-speed USB device number 3 using exynos-ehci [ 9.784601] usb 1-3: device not accepting address 3, error -71 [ 9.784838] usb usb1-port3: device 1-3 not suspended yet Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09usb: force warm reset to break link re-connect livelockDan Williams
Resuming a powered down port sometimes results in the port state being stuck in the training sequence. hub 3-0:1.0: debounce: port 1: total 2000ms stable 0ms status 0x2e0 port1: can't get reconnection after setting port power on, status -110 hub 3-0:1.0: port 1 status 0000.02e0 after resume, -19 usb 3-1: can't resume, status -19 hub 3-0:1.0: logical disconnect on port 1 In the case above we wait for the port re-connect timeout of 2 seconds and observe that the port status is USB_SS_PORT_LS_POLLING (although it is likely toggling between this state and USB_SS_PORT_LS_RX_DETECT). This is indicative of a case where the device is failing to progress the link training state machine. It is resolved by issuing a warm reset to get the hub and device link state machines back in sync. hub 3-0:1.0: debounce: port 1: total 2000ms stable 0ms status 0x2e0 usb usb3: port1 usb_port_runtime_resume requires warm reset hub 3-0:1.0: port 1 not warm reset yet, waiting 50ms usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd After a reconnect timeout when we expect the device to be present, force a warm reset of the device. Note that we can not simply look at the link status to determine if a warm reset is required as any of the training states USB_SS_PORT_LS_POLLING, USB_SS_PORT_LS_RX_DETECT, or USB_SS_PORT_LS_COMP_MOD are valid states that do not indicate the need for warm reset by themselves. Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: Vincent Palatin <vpalatin@chromium.org> Cc: Lan Tianyu <tianyu.lan@intel.com> Cc: Ksenia Ragiadakou <burzalodowa@gmail.com> Cc: Vivek Gautam <gautam.vivek@samsung.com> Cc: Douglas Anderson <dianders@chromium.org> Cc: Felipe Balbi <balbi@ti.com> Cc: Sunil Joshi <joshi@samsung.com> Cc: Hans de Goede <hdegoede@redhat.com> Acked-by: Julius Werner <jwerner@chromium.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09usb: allow lpm (en/dis)able only if device is atleast in default statePratyush Anand
When a USB device is disconnected, usb_unbind_interface is called, which tries to enable and disable LPM. usb_enable_lpm also try to send a control command SET SEL to the device. Since device is already disconnected, therefore it does not make sense to execute usb_(en/dis)able_lpm. This patch returns from usb_(en/dis)able_lpm, if device was not in default state atleast. Signed-off-by: Pratyush Anand <pratyush.anand@st.com> Tested-by: Aymen Bouattay <aymen.bouattay@st.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-17usb: fix hub-port pm_runtime_enable() vs runtime pm transitionsDan Williams
Commit 9262c19d14c4 "usb: disable port power control if not supported in wHubCharacteristics" gated enabling runtime pm for usb_port devices on whether the parent hub supports power control, which causes a regression. The port must still be allowed to carry out runtime pm callbacks and receive a -EAGAIN or -EBUSY result. Otherwise the usb_port device will transition to the pm error state and trigger the same for the child usb_device. Prior to the offending commit usb_hub_create_port_device() arranged for runtime pm to be disabled is dev_pm_qos_expose_flags() failed. Instead, force the default state of PM_QOS_FLAG_NO_POWER_OFF flag to be set prior to enabling runtime pm. If that policy can not be set then fail registration. Report: http://marc.info/?l=linux-usb&m=140290586301336&w=2 Fixes: 9262c19d14c4 ("usb: disable port power control if not supported in wHubCharacteristics") Reported-by: Bjørn Mork <bjorn@mork.no> Reported-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-17usb: quiet peer failure warning, disable poweroffDan Williams
In the case where platform firmware has specified conflicting values for port locations it is confusing and otherwise not helpful to throw a backtrace. Instead, include enough information to determine that firmware has done something wrong and globally disable port poweroff. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-17usb: improve "not suspended yet" message in hub_suspend()Dan Williams
Reading through a recent bug report [1], Alan notes: "Dan, the warning message in hub_suspend() should mention that the child device isn't suspended yet." ...update the warning from: "usb usb3-port4: not suspended yet" ...to: "usb usb3-port4: device 3-4: not suspended yet" [1]: http://marc.info/?l=linux-usb&m=140290586301336&w=2 Reported-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-17usb: fix ->update_hub_device() vs hdev->maxchildDan Williams
Commit d8521afe3586 "usb: assign default peer ports for root hubs" delayed marking a hub valid (set hdev->maxchild) until it had been fully configured and to enable the publishing of valid hubs to be serialized by usb_port_peer_mutex. However, xhci_update_hub_device() in some cases depends on hdev->maxchild already being set. Do the minimal fix and move it after the setting of hdev->maxchild. Cc: Mathias Nyman <mathias.nyman@linux.intel.com> Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu> Tested-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-08Merge branch 'next' (accumulated 3.16 merge window patches) into masterLinus Torvalds
Now that 3.15 is released, this merges the 'next' branch into 'master', bringing us to the normal situation where my 'master' branch is the merge window. * accumulated work in next: (6809 commits) ufs: sb mutex merge + mutex_destroy powerpc: update comments for generic idle conversion cris: update comments for generic idle conversion idle: remove cpu_idle() forward declarations nbd: zero from and len fields in NBD_CMD_DISCONNECT. mm: convert some level-less printks to pr_* MAINTAINERS: adi-buildroot-devel is moderated MAINTAINERS: add linux-api for review of API/ABI changes mm/kmemleak-test.c: use pr_fmt for logging fs/dlm/debug_fs.c: replace seq_printf by seq_puts fs/dlm/lockspace.c: convert simple_str to kstr fs/dlm/config.c: convert simple_str to kstr mm: mark remap_file_pages() syscall as deprecated mm: memcontrol: remove unnecessary memcg argument from soft limit functions mm: memcontrol: clean up memcg zoneinfo lookup mm/memblock.c: call kmemleak directly from memblock_(alloc|free) mm/mempool.c: update the kmemleak stack trace for mempool allocations lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations mm: introduce kmemleak_update_trace() mm/kmemleak.c: use %u to print ->checksum ...
2014-06-02usb: hub_handle_remote_wakeup() only exists for CONFIG_PM=yStephen Rothwell
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27usb: resume child device when port is powered onDan Williams
Unconditionally wake up the child device when the power session is recovered. This addresses the following scenarios: 1/ The device may need a reset on power-session loss, without this change port power-on recovery exposes khubd to scenarios that usb_port_resume() is set to handle. Prior to port power control the only time a power session would be lost is during dpm_suspend of the hub. In that scenario usb_port_resume() is guaranteed to be called prior to khubd running for that port. With this change we wakeup the child device as soon as possible (prior to khubd running again for this port). Although khubd has facilities to wake a child device it will only do so if the portstatus / portchange indicates a suspend state. In the case of port power control we are not coming from a hub-port-suspend state. This implementation simply uses pm_request_resume() to wake the device and relies on the port_dev->status_lock to prevent any collisions between khubd and usb_port_resume(). 2/ This mechanism rate limits port power toggling. The minimum port power on/off period is now gated by the child device suspend/resume latency. Empirically this mitigates devices downgrading their connection on perceived instability of the host connection. This ratelimiting is really only relevant to port power control testing, but it is a nice side effect of closing the above race. Namely, the race of khubd for the given port running while a usb_port_resume() event is pending. 3/ Going forward we are finding that power-session recovery requires warm-resets (http://marc.info/?t=138659232900003&r=1&w=2). This mechanism allows for warm-resets to be requested at the same point in the resume path for hub dpm_suspend power session losses, or port rpm_suspend power session losses. 4/ If the device *was* disconnected the only time we'll know for sure is after a failed resume, so it's necessary for usb_port_runtime_resume() to expedite a usb_port_resume() to clean up the removed device. The reasoning for this is "least surprise" for the user. Turning on a port means that hotplug detection is again enabled for the port, it is surprising that devices that were removed while the port was off are not disconnected until they are attempted to be used. As a user "why would I try to use a device I removed from the system?" 1, 2, and 4 are not a problem in the system dpm_resume() case because, although the power-session is lost, khubd is frozen until after device resume. For the rpm_resume() case pm_request_resume() is used to request re-validation of the device, and if it happens to collide with a khubd run we rely on the port_dev->status_lock to synchronize those operations. Besides testing, the primary scenario where this mechanism is expected to be triggered is when the user changes the port power policy (control/pm_qos_no_poweroff, or power/control). Each time power is enabled want to revalidate the child device, where the revalidation is handled by usb_port_resume(). Given that this arranges for port_dev->child to be de-referenced in usb_port_runtime_resume() we need to make sure not to collide with usb_disconnect() that frees the usb_device. To this end we hold the port active with the "child_usage" reference across the disconnect event. Subsequently, the need to access hub->child_usage_bits lead to the creation of hub_disconnect_children() to remove any ambiguity of which "hub" is being acted on in usb_disconnect() (prompted-by sharp eyes from Alan). Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27usb: hub_handle_remote_wakeup() depends on CONFIG_PM_RUNTIME=yDan Williams
Per Alan: "You mean from within hub_handle_remote_wakeup()? That routine will never get called if CONFIG_PM_RUNTIME isn't enabled, because khubd never sees wakeup requests if they arise during system suspend. In fact, that routine ought to go inside the "#ifdef CONFIG_PM_RUNTIME" portion of hub.c, along with the other suspend/resume code." Suggested-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27usb: introduce port status lockDan Williams
In general we do not want khubd to act on port status changes that are the result of in progress resets or USB runtime PM operations. Specifically port power control testing has been able to trigger an unintended disconnect in hub_port_connect_change(), paraphrasing: if ((portstatus & USB_PORT_STAT_CONNECTION) && udev && udev->state != USB_STATE_NOTATTACHED) { if (portstatus & USB_PORT_STAT_ENABLE) { /* Nothing to do */ } else if (udev->state == USB_STATE_SUSPENDED && udev->persist_enabled) { ... } else { /* Don't resuscitate */; } } ...by falling to the "Don't resuscitate" path or missing USB_PORT_STAT_CONNECTION because usb_port_resume() was in the middle of modifying the port status. So, we want a new lock to hold off khubd for a given port while the child device is being suspended, resumed, or reset. The lock ordering rules are now usb_lock_device() => usb_lock_port(). This is mandated by the device core which may hold the device_lock on the usb_device before invoking usb_port_{suspend|resume} which in turn take the status_lock on the usb_port. We attempt to hold the status_lock for the duration of a port_event() run, and drop/re-acquire it when needing to take the device_lock. The lock is also dropped/re-acquired during hub_port_reconnect(). This patch also deletes hub->busy_bits as all use cases are now covered by port PM runtime synchronization or the port->status_lock and it pushes down usb_device_lock() into usb_remote_wakeup(). Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27usb: synchronize port poweroff and khubdDan Williams
If a port is powered-off, or in the process of being powered-off, prevent khubd from operating on it. Otherwise, the following sequence of events leading to an unintended disconnect may occur: Events: (0) <set pm_qos_no_poweroff to '0' for port1> (1) hub 2-2:1.0: hub_resume (2) hub 2-2:1.0: port 1: status 0301 change 0000 (3) hub 2-2:1.0: state 7 ports 4 chg 0002 evt 0000 (4) hub 2-2:1.0: port 1, power off status 0000, change 0000, 12 Mb/s (5) usb 2-2.1: USB disconnect, device number 5 Description: (1) hub is resumed before sending a ClearPortFeature request (2) hub_activate() notices the port is connected and sets hub->change_bits for the port (3) hub_events() starts, but at the same time the port suspends (4) hub_connect_change() sees the disabled port and triggers disconnect Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27usb: refactor port handling in hub_events()Dan Williams
In preparation for synchronizing port handling with pm_runtime transitions refactor port handling into its own subroutine. We expect that clearing some status flags will be required regardless of the port state, so handle those first and group all non-trivial actions at the bottom of the routine. This also splits off the bottom half of hub_port_connect_change() into hub_port_reconnect() in prepartion for introducing a port->status_lock. hub_port_reconnect() will expect the port lock to not be held while hub_port_connect_change() expects to enter with it held. Other cleanups include: 1/ reflowing to 80 columns 2/ replacing redundant usages of 'hub->hdev' with 'hdev' 3/ consolidate clearing of ->change_bits() in hub_port_connect_change 4/ consolidate calls to usb_reset_device Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27usb: usb3 ports do not support FEAT_C_ENABLEDan Williams
The port pm_runtime implementation unconditionally clears FEAT_C_ENABLE after clearing PORT_POWER, but the bit is reserved on usb3 hub ports. We expect khubd to be prevented from running because the port state is not RPM_ACTIVE, so we need to clear any errors for usb2 ports. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27usb: don't clear FEAT_C_ENABLE on usb_port_runtime_resume failureDan Williams
Three reasons: 1/ It's an invalid operation on usb3 ports 2/ There's no guarantee of when / if a usb2 port has entered an error state relative to PORT_POWER request 3/ The port is active / powered at this point, so khubd will clear it as a matter of course Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27usb: block suspension of superspeed port while hispeed peer is activeDan Williams
ClearPortFeature(PORT_POWER) on a usb3 port places the port in either a DSPORT.Powered-off-detect / DSPORT.Powered-off-reset loop, or the DSPORT.Powered-off state. There is no way to ensure that RX terminations will persist in this state, so it is possible a device will degrade to its usb2 connection. Prevent this by blocking power-off of a usb3 port while its usb2 peer is active, and powering on a usb3 port before its usb2 peer. By default the latency between peer power-on events is 0. In order for the device to not see usb2 active while usb3 is still powering up inject the hub recommended power_on_good delay. In support of satisfying the power_on_good delay outside of hub_power_on() refactor the places where the delay is consumed to call a new hub_power_on_good_delay() helper. Finally, because this introduces several new checks for whether a port is_superspeed, cache that disctinction at port creation so that we don't need to keep looking up the parent hub device. Acked-by: Alan Stern <stern@rowland.harvard.edu> [alan]: add a 'superspeed' flag to the port Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27usb: make usb_port flags atomic, rename did_runtime_put to child_usageDan Williams
We want to manipulate ->did_runtime_put in usb_port_runtime_resume(), but we don't want that to collide with other updates. Move usb_port flags to new port-bitmap fields in usb_hub. "did_runtime_put" is renamed "child_usage_bits" to reflect that it is strictly standing in for the fact that usb_devices are not the device_model children of their parent port. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>