Age | Commit message (Collapse) | Author |
|
The geni serial driver had the rather sketchy hack in it where it
would adjust the number of bytes per RX FIFO word from 4 down to 1 if
it detected that CONFIG_CONSOLE_POLL was enabled (for kgdb) and this
was a console port (defined by the kernel directing output to this
port via the "console=" command line argument).
The problem with that sketchy hack is that it's possible to run kgdb
over a serial port even if it isn't used for console.
Let's avoid the hack by simply handling the 4-bytes-per-FIFO word case
for kdb. We'll have to have a (very small) cache but that should be
fine.
A nice side effect of this patch is that an agetty (or similar)
running on this port is less likely to drop characters. We'll
have roughly 4 times the RX FIFO depth than we used to now.
NOTE: the character cache here isn't shared between the polling API
and the non-polling API. That means that, technically, the polling
API could eat a few extra bytes. This doesn't seem to pose a huge
problem in reality because we'll only get several characters per FIFO
word if those characters are all received at nearly the same time and
we don't really expect non-kgdb characters to be sent to the same port
as kgdb at the exact same time we're exiting kgdb.
ALSO NOTE: we still have the sketchy hack for setting the number of
bytes per TX FIFO word in place, but that one is less bad. kgdb
doesn't have any problem with this because it always just sends 1 byte
at a time and waits for it to finish. The TX FIFO hack is only really
needed for console output. In any case, a future patch will remove
that hack, too.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200626125844.1.I8546ecb6c5beb054f70c5302d1a7293484212cd1@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The comment near to uart_port_spin_lock_init() says:
Ensure that the serial console lock is initialised early.
If this port is a console, then the spinlock is already initialised.
and there is nothing about enabled or disabled consoles. The commit
a3cb39d258ef ("serial: core: Allow detach and attach serial device
for console") made a change, which follows the comment, and also to
prevent reinitialisation of the lock in use, when user detaches and
attaches back the same console device. But this change discovers
another issue, that uart_add_one_port() tries to access a spin lock
that now may be uninitialised. This happens when a driver expects
the serial core to register a console on its behalf. In this case
we must initialise a spin lock before use.
Fixes: a3cb39d258ef ("serial: core: Allow detach and attach serial device for console")
Reported-by: Marc Zyngier <maz@kernel.org>
Reported-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20200706214903.56148-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver calls ioremap() in probe, but it misses calling iounmap() in
probe's error handler and remove.
Add the missed calls to fix it.
Fixes: 47d37d6f94cc ("serial: Add auart driver for i.MX23/28")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200709135608.68290-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
serial core expects the spinlock to be initialized by the controller
driver for serial console, this patch makes sure the spinlock is
initialized, fixing the below issue:
[ 0.865928] BUG: spinlock bad magic on CPU#0, swapper/0/1
[ 0.865945] lock: sci_ports+0x0/0x4c80, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[ 0.865955] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.8.0-rc1+ #112
[ 0.865961] Hardware name: HopeRun HiHope RZ/G2H with sub board (DT)
[ 0.865968] Call trace:
[ 0.865979] dump_backtrace+0x0/0x1d8
[ 0.865985] show_stack+0x14/0x20
[ 0.865996] dump_stack+0xe8/0x130
[ 0.866006] spin_dump+0x6c/0x88
[ 0.866012] do_raw_spin_lock+0xb0/0xf8
[ 0.866023] _raw_spin_lock_irqsave+0x80/0xa0
[ 0.866032] uart_add_one_port+0x3a4/0x4e0
[ 0.866039] sci_probe+0x504/0x7c8
[ 0.866048] platform_drv_probe+0x50/0xa0
[ 0.866059] really_probe+0xdc/0x330
[ 0.866066] driver_probe_device+0x58/0xb8
[ 0.866072] device_driver_attach+0x6c/0x90
[ 0.866078] __driver_attach+0x88/0xd0
[ 0.866085] bus_for_each_dev+0x74/0xc8
[ 0.866091] driver_attach+0x20/0x28
[ 0.866098] bus_add_driver+0x14c/0x1f8
[ 0.866104] driver_register+0x60/0x110
[ 0.866109] __platform_driver_register+0x40/0x48
[ 0.866119] sci_init+0x2c/0x34
[ 0.866127] do_one_initcall+0x88/0x428
[ 0.866137] kernel_init_freeable+0x2c0/0x328
[ 0.866143] kernel_init+0x10/0x108
[ 0.866150] ret_from_fork+0x10/0x18
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: a3cb39d258ef ("serial: core: Allow detach and attach serial device for console")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1593618100-2151-1-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tty TIOCL_SETSEL ioctl allocates a memory buffer big enough for text
selection area. The maximum allowed console size is
VC_RESIZE_MAXCOL * VC_RESIZE_MAXROW == 32767*32767 == ~1GB and typical
MAX_ORDER is set to allow allocations lot less than than (circa 16MB).
So it is quite possible to trigger huge allocation (and syzkaller just
did that) which is going to fail (which is fine) with a backtrace in
mm/page_alloc.c at WARN_ON_ONCE(!(gfp_mask & __GFP_NOWARN)) and
this may trigger panic (if panic_on_warn is enabled) and
leak kernel addresses to dmesg.
This passes __GFP_NOWARN to kmalloc_array to avoid unnecessary user-
triggered WARN_ON. Note that the error is not ignored and
the warning is still printed.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Link: https://lore.kernel.org/r/20200617070444.116704-1-aik@ozlabs.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support of generic DT binding for annoucing RTS/CTS lines. The initial
binding 'st,hw-flow-control' is not needed anymore since generic binding
is available, but is kept for backward compatibility.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/20200520133932.30441-3-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix typo: "tigger" --> "trigger"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Link: https://lore.kernel.org/r/20200609160249.31329-1-f.suligoi@asem.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 2ae11c46d5fdc46cb396e35911c713d271056d35.
It turned out to break the ultra96-rev1, e.g., which uses uart1 as
serial0 (and stdout-path = "serial0:115200n8").
Fixes: 2ae11c46d5fd ("tty: xilinx_uartps: Fix missing id assignment to the console")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f4092727-d8f5-5f91-2c9f-76643aace993@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 8e20fc391711 ("serial_core: Move sysrq functions from header
file") converted the inline sysrq helpers to exported functions which
are now called for every received character, interrupt and break signal
also on systems without CONFIG_MAGIC_SYSRQ_SERIAL instead of being
optimised away by the compiler.
Inlining these helpers again also avoids the function call overhead when
CONFIG_MAGIC_SYSRQ_SERIAL is enabled (e.g. when the port is not used as
a console).
Fixes: 8e20fc391711 ("serial_core: Move sysrq functions from header file")
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/20200610152232.16925-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit da9a5aa3402db0ff3b57216d8dbf2478e1046cae.
In order to ease backporting a fix for a sysrq regression, revert this
rewrite which was since added on top.
The other sysrq helpers now bail out early when sysrq is not enabled;
it's better to keep that pattern here as well.
Note that the __releases() attribute won't be needed after the follow-on
fix either.
Fixes: da9a5aa3402d ("serial: core: Refactor uart_unlock_and_check_sysrq()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200610152232.16925-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200618122952.88265-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618123320.88612-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618122744.88204-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618122024.87170-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618095144.73852-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In commit a4912303ac6f ("serial: kgdboc: Allow earlycon initialization
to be deferred") it looks like Daniel really took Linus's new
suggestion about not needing to wrap at 80 columns to heart and he
jammed two full lines of comments into one line. Either that or he
just somehow accidentally deleted a carriage return when doing final
edits on the patch. In either case let's make it look prettier.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200602124044.1.Iee31247bc080d42a02e167454b1225a1b4283705@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since dev_err() calls can lead to synchronous writes to another serial
console these calls can provide significant latency during irq-handling
in tegra_uart_isr(). With this latency another interrupt is likely to
apper during handling of the first interrupt, which might lock up the
kernel completely.
These errors are reported to the error counters so converting the
dev_err() to dev_dbg() is appropriate.
Signed-off-by: Randolph Maaßen <gaireg@gaireg.de>
Link: https://lore.kernel.org/r/20200605145714.9964-1-gaireg@gaireg.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
get_num_ports returns -ENODEV, and the result is stored in int, so it
should not be unsigned. Zero ports does not seem to make sense, so
make that check consistent.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Link: https://lore.kernel.org/r/20200606151146.GA10940@amd
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop the recently added gpio include from the serial-core header in
favour of a forward declaration and instead include the gpio header only
where needed.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200610155121.14014-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix kernel-doc warnings in serial_core.c:
../drivers/tty/serial/serial_core.c:3300: warning: Function parameter or member 'port' not described in 'uart_get_rs485_mode'
../drivers/tty/serial/serial_core.c:3300: warning: Excess function parameter 'dev' description in 'uart_get_rs485_mode'
../drivers/tty/serial/serial_core.c:3300: warning: Excess function parameter 'rs485conf' description in 'uart_get_rs485_mode'
Fixes: c150c0f362c1 ("serial: Allow uart_get_rs485_mode() to return errno")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/e170db8e-5c8b-27ac-79a4-81b96ac0ca2d@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The formula for the baud rate is
baud rate = "baud clock / ((OSR+1) × SBR)
Algorithm used in function lpuart32_serial_setbrg() only changes
the SBR. Even with maxmum value put in, OSR stays at 0x7 and the
lowest baud rate would be ~ 2600 bps
Update the algorithm to allow driver operation at 1200,2400 or 600 bps
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Link: https://lore.kernel.org/r/1593170434-13524-1-git-send-email-vabhav.sharma@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ARRAY_SIZE() is the number of elements but we want the number of
bytes so sizeof() is more appropriate. Fortunately, it's the same
thing here because this is an array of u8 so this doesn't change
runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200624132744.GD9972@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
devm_gpiod_get_index() doesn't return NULL but -ENOENT when the
requested GPIO doesn't exist, leading to the following messages:
[ 2.742468] gpiod_direction_input: invalid GPIO (errorpointer)
[ 2.748147] can't set direction for gpio #2: -2
[ 2.753081] gpiod_direction_input: invalid GPIO (errorpointer)
[ 2.758724] can't set direction for gpio #3: -2
[ 2.763666] gpiod_direction_output: invalid GPIO (errorpointer)
[ 2.769394] can't set direction for gpio #4: -2
[ 2.774341] gpiod_direction_input: invalid GPIO (errorpointer)
[ 2.779981] can't set direction for gpio #5: -2
[ 2.784545] ff000a20.serial: ttyCPM1 at MMIO 0xfff00a20 (irq = 39, base_baud = 8250000) is a CPM UART
Use devm_gpiod_get_index_optional() instead.
At the same time, handle the error case and properly exit
with an error.
Fixes: 97cbaf2c829b ("tty: serial: cpm_uart: Convert to use GPIO descriptors")
Cc: stable@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/694a25fdce548c5ee8b060ef6a4b02746b8f25c0.1591986307.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a spelling mistake in a comment. Fix it.
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20200617105907.7143-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make the code slightly more readable by removing unneeded line breaks,
adding missing line breaks and white spaces. This also fixes few strict
checkpatch suggestions:
CHECK: spaces preferred around that '-' (ctx:VxV)
CHECK: Unbalanced braces around else statement
CHECK: Lines should not end with a '('
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200617152856.18086-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In kgdb context, calling console handlers aren't safe due to locks used
in those handlers which could in turn lead to a deadlock. Although, using
oops_in_progress increases the chance to bypass locks in most console
handlers but it might not be sufficient enough in case a console uses
more locks (VT/TTY is good example).
Currently when a driver provides both polling I/O and a console then kdb
will output using the console. We can increase robustness by using the
currently active polling I/O driver (which should be lockless) instead
of the corresponding console. For several common cases (e.g. an
embedded system with a single serial port that is used both for console
output and debugger I/O) this will result in no console handler being
used.
In order to achieve this we need to reverse the order of preference to
use dbg_io_ops (uses polling I/O mode) over console APIs. So we just
store "struct console" that represents debugger I/O in dbg_io_ops and
while emitting kdb messages, skip console that matches dbg_io_ops
console in order to avoid duplicate messages. After this change,
"is_console" param becomes redundant and hence removed.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/1591264879-25920-5-git-send-email-sumit.garg@linaro.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
|
|
Use the 'common' foo_console_setup() naming scheme. There are 71
foo_console_setup() callbacks and only one foo_setup_console().
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20200619172240.754910-1-sergey.senozhatsky@gmail.com
|
|
For unifying console ->setup() handling, which is poorly documented,
return error code, rather than non-zero arbitrary number.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20200618164751.56828-5-andriy.shevchenko@linux.intel.com
|
|
For unifying console ->setup() handling, which is poorly documented,
return error code, rather than non-zero arbitrary number.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20200618164751.56828-4-andriy.shevchenko@linux.intel.com
|
|
For unifying console ->setup() handling, which is poorly documented,
return error code, rather than non-zero arbitrary number.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20200618164751.56828-3-andriy.shevchenko@linux.intel.com
|
|
geni serial needs to express a perforamnce state requirement on CX
powerdomain depending on the frequency of the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/1592222564-13556-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Get the interconnect paths for Uart based Serial Engine device
and vote according to the baud rate requirement of the driver.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1592908737-7068-5-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
QUP core clock is shared among all the SE drivers present on particular
QUP wrapper, the system will reset(unclocked access) if earlycon used after
QUP core clock is put to 0 from other SE drivers before real console comes
up.
As earlycon can't vote for it's QUP core need, to fix this add ICC
support to common/QUP wrapper driver and put vote for QUP core from
probe on behalf of earlycon and remove vote during earlycon exit call.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1592908737-7068-3-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
We can also thaw non-block file systems. Remove the CONFIG_BLOCK in
sysrq.c after making the prototype available unconditionally.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The vmemdup_user() function has no 2-factor argument form. Use array_size()
to check for the overflow.
Signed-off-by: Denis Efremov <efremov@linux.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20200603102804.2110817-1-efremov@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Synchronize with others and check perm directly in vt_k_ioctl.
We do not need to pass perm to do_fontx_ioctl and do_unimap_ioctl then.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-38-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's too long to be inlined.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-37-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This also eliminates the ifdeffery by using if and __is_defined.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-36-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's too long to be inlined.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-35-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's too long to be inlined.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-34-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's too long to be inlined.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-33-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We create a new vt_io_ioctl here and move there all the IO ioctls. This
makes vt_ioctl significantly smaller.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-32-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We create a new vt_k_ioctl here and move there all the K* ioctls. This
makes vt_ioctl significantly smaller.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-31-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
They were used for the first parameter of put_user. But put_user accepts
constants in the parameter and also determines the type only by the
second parameter. So we can safely drop these helpers and simplify the
code a bit.
Including the removal of set_int label.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-30-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is still a leftover from BKL, when we locked it around vt_ioctl's
code. We can return instead of breaks in the switch loop. And we can
return in case of errors too. This allows for sifting of the code to the
left in some cases.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-29-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All the attributes are bools, so do a simple shift instead of tests and
constants as bool is either 0 or 1.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-28-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There were too many parentheses in invert_screen, remove them and align
the code in invert_screen a bit.
No functional change intended.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-27-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We defined macros for all the magic constants in the previous patch. So
let us use the macro in the code now.
No functional change intended.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-usb@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Acked-by: Helge Deller <deller@gmx.de>
Link: https://lore.kernel.org/r/20200615074910.19267-26-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The cursor code used to use magic constants, ANDs, ORs, and some macros.
Redefine all this to make some sense.
In particular:
* Drop CUR_DEFAULT, which is CUR_UNDERLINE. CUR_DEFAULT was used only
for cur_default variable initialization, so use CUR_UNDERLINE there to
make obvious what's the default.
* Drop CUR_HWMASK. Instead, define CUR_SIZE() which explains it more.
And use it all over the places.
* Define few more masks and bits which will be used in next patches
instead of magic constants.
* Define CUR_MAKE to build up cursor value.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Link: https://lore.kernel.org/r/20200615074910.19267-25-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Format add_softcursor according to CodingStyle. Until now, it was a mess
of letters.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200615074910.19267-24-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|