summaryrefslogtreecommitdiff
path: root/drivers/tty/serial/8250
AgeCommit message (Collapse)Author
2015-01-09tty: serial: 8250: drop owner assignment from platform_driversWolfram Sang
This platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-09serial: 8250: add support for ACPI-probed serial port for X-Gene platformFeng Kan
Enable APM X-Gene SoC serial port functionality when using ACPI table to initialize serial port. Signed-off-by: Feng Kan <fkan@apm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-09serial: 8250_dma: terminate transfer explicitly when timeoutAndy Shevchenko
There is no need to terminate transfer in the __dma_rx_complete() since it's called at the end of transfer. Special case when serial timeout occurs is handled separately where we have to terminate transfer. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-09serial: omap_8250: Fix RTS handling, part BPeter Hurley
Because the OMAP3 UART ignores MCR[1] (RTS) in autoRTS mode, autoRTS mode must not be enabled unless RTS is set (or port->mctrl & TIOCM_RTS, which is equivalent). Fixes premature raising of RTS in omap_8250_set_termios() -- RTS was raised even before UART mode was selected. Fixes raise of RTS after port has been shutdown; omap_8250_pm() re-enabled RTS after omap_8250_shutdown(). Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-09serial: omap_8250: Fix RTS handlingPeter Hurley
The OMAP3 UART ignores MCR[1] (ie., UART_MCR_RTS) when in autoRTS mode (UPF_HARD_FLOW + CRTSCTS). This makes it impossible for either the serial core or userspace to manually flow control the sender. Disable autoRTS mode when RTS is lowered and restore the previous mode when RTS is raised. Note that the OMAP3 UART provides no mechanism for switching from autoRTS mode without corrupting incoming data; to access the necessary register, the line control settings must be set to 8-e-2 and thus any data received during that time will be interpreted with those settings. This corruption has been observed in practice. Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-09tty: serial: 8250: omap: add ttySx console if the user didn'tSebastian Andrzej Siewior
This patch invokes add_preferred_console() with ttyS based on ttyO arguments if the user didn't specify it on its own. This ensures that the user will see the kernel booting on his serial console in case he forgot to update the command line. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-19tty: 8250_omap: Replace CONFIG_PM_RUNTIME with CONFIG_PMRafael J. Wysocki
The 8250_omap serial driver is a new user of CONFIG_PM_RUNTIME. However, after commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks depending on CONFIG_PM_RUNTIME may now be changed to depend on CONFIG_PM. Replace CONFIG_PM_RUNTIME with CONFIG_PM in 8250_omap.c. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-18Merge tag 'pm+acpi-3.19-rc1-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull more ACPI and power management updates from Rafael Wysocki: "These are regression fixes (leds-gpio, ACPI backlight driver, operating performance points library, ACPI device enumeration messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device PM), some cleanups in the operating performance points (OPP) framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of minor intel_pstate driver changes, a new MAINTAINERS entry for it and an ACPI fan driver change needed for better support of thermal management in user space. Specifics: - Fix a regression in leds-gpio introduced by a recent commit that inadvertently changed the name of one of the properties used by the driver (Fabio Estevam). - Fix a regression in the ACPI backlight driver introduced by a recent fix that missed one special case that had to be taken into account (Aaron Lu). - Drop the level of some new kernel messages from the ACPI core introduced by a recent commit to KERN_DEBUG which they should have used from the start and drop some other unuseful KERN_ERR messages printed by ACPI (Rafael J Wysocki). - Revert an incorrect commit modifying the cpupower tool (Prarit Bhargava). - Fix two regressions introduced by recent commits in the OPP library and clean up some existing minor issues in that code (Viresh Kumar). - Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the tree (or drop it where that can be done) in order to make it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf Hansson, Ludovic Desroches). There will be one more "CONFIG_PM_RUNTIME removal" batch after this one, because some new uses of it have been introduced during the current merge window, but that should be sufficient to finally get rid of it. - Make the ACPI EC driver more robust against race conditions related to GPE handler installation failures (Lv Zheng). - Prevent the ACPI device PM core code from attempting to disable GPEs that it has not enabled which confuses ACPICA and makes it report errors unnecessarily (Rafael J Wysocki). - Add a "force" command line switch to the intel_pstate driver to make it possible to override the blacklisting of some systems in that driver if needed (Ethan Zhao). - Improve intel_pstate code documentation and add a MAINTAINERS entry for it (Kristen Carlson Accardi). - Make the ACPI fan driver create cooling device interfaces witn names that reflect the IDs of the ACPI device objects they are associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B"). That's necessary for user space thermal management tools to be able to connect the fans with the parts of the system they are supposed to be cooling properly. From Srinivas Pandruvada" * tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits) MAINTAINERS: add entry for intel_pstate ACPI / video: update the skip case for acpi_video_device_in_dod() power / PM: Eliminate CONFIG_PM_RUNTIME NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM ACPI / EC: Fix unexpected ec_remove_handlers() invocations Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()" tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c PM: Remove the SET_PM_RUNTIME_PM_OPS() macro mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro PM / Kconfig: Replace PM_RUNTIME with PM in dependencies ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM ACPI / PM: Do not disable wakeup GPEs that have not been enabled ACPI / utils: Drop error messages from acpi_evaluate_reference() ...
2014-12-14Merge tag 'driver-core-3.19-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core update from Greg KH: "Here's the set of driver core patches for 3.19-rc1. They are dominated by the removal of the .owner field in platform drivers. They touch a lot of files, but they are "simple" changes, just removing a line in a structure. Other than that, a few minor driver core and debugfs changes. There are some ath9k patches coming in through this tree that have been acked by the wireless maintainers as they relied on the debugfs changes. Everything has been in linux-next for a while" * tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits) Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries" fs: debugfs: add forward declaration for struct device type firmware class: Deletion of an unnecessary check before the function call "vunmap" firmware loader: fix hung task warning dump devcoredump: provide a one-way disable function device: Add dev_<level>_once variants ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries ath: use seq_file api for ath9k debugfs files debugfs: add helper function to create device related seq_file drivers/base: cacheinfo: remove noisy error boot message Revert "core: platform: add warning if driver has no owner" drivers: base: support cpu cache information interface to userspace via sysfs drivers: base: add cpu_device_create to support per-cpu devices topology: replace custom attribute macros with standard DEVICE_ATTR* cpumask: factor out show_cpumap into separate helper function driver core: Fix unbalanced device reference in drivers_probe driver core: fix race with userland in device_add() sysfs/kernfs: make read requests on pre-alloc files use the buffer. sysfs/kernfs: allow attributes to request write buffer be pre-allocated. fs: sysfs: return EGBIG on write if offset is larger than file size ...
2014-12-13tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PMRafael J. Wysocki
After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks depending on CONFIG_PM_RUNTIME may now be changed to depend on CONFIG_PM. Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under drivers/tty/. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-25serial: 8250: don't attempt a trylock if in sysrqRabin Vincent
Attempting to use SysRq via the 8250 serial port with spin lock debugging on on a uniprocessor system results in the following splat: SysRq : BUG: spinlock trylock failure on UP on CPU#0, swapper/0 lock: serial8250_ports+0x0/0x8c0, .magic: dead4ead, .owner: swapper/0, .owner_cpu: 0 CPU: 0 PID: 0 Comm: swapper Not tainted 3.18.0-rc4+ #37 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014 ffffffff8245ba00 ffffffff81628b28 ffffffff812c8d27 ffffffff81628b48 ffffffff8106812e ffffffff8245ba00 ffffffff814e22ed ffffffff81628b68 ffffffff810681a6 0000000000000000 0000000000000000 ffffffff81628b88 Call Trace: <IRQ> [<ffffffff812c8d27>] dump_stack+0x19/0x1b [<ffffffff8106812e>] spin_dump+0x7e/0xd0 [<ffffffff810681a6>] spin_bug+0x26/0x30 [<ffffffff8106843c>] do_raw_spin_trylock+0x4c/0x60 [<ffffffff812cdb1d>] _raw_spin_trylock+0x1d/0x60 [<ffffffff812336d8>] serial8250_console_write+0x68/0x190 [<ffffffff811eb0b0>] ? sprintf+0x40/0x50 [<ffffffff8106ab5e>] call_console_drivers.constprop.11+0x9e/0xf0 [<ffffffff8106b276>] console_unlock+0x3e6/0x490 [<ffffffff8106b595>] vprintk_emit+0x275/0x530 [<ffffffff812c869a>] printk+0x4d/0x4f [<ffffffff8121e612>] __handle_sysrq+0x62/0x1b0 [<ffffffff8121e5b5>] ? __handle_sysrq+0x5/0x1b0 [<ffffffff8121ebc6>] handle_sysrq+0x26/0x30 [<ffffffff81233157>] serial8250_rx_chars+0x1d7/0x250 [<ffffffff812338bb>] serial8250_handle_irq+0x7b/0x90 [<ffffffff812338f3>] serial8250_default_handle_irq+0x23/0x30 [<ffffffff812318b3>] serial8250_interrupt+0x63/0xe0 [<ffffffff8106d80e>] handle_irq_event_percpu+0x4e/0x200 [<ffffffff8106da01>] handle_irq_event+0x41/0x70 [<ffffffff810701ee>] ? handle_edge_irq+0x1e/0x110 [<ffffffff8107026e>] handle_edge_irq+0x9e/0x110 [<ffffffff810041c2>] handle_irq+0x22/0x40 [<ffffffff812d096e>] do_IRQ+0x4e/0xf0 [<ffffffff812cf4ed>] common_interrupt+0x6d/0x6d <EOI> [<ffffffff8100acbf>] ? default_idle+0x1f/0xd0 [<ffffffff8100acbd>] ? default_idle+0x1d/0xd0 [<ffffffff8100b61f>] arch_cpu_idle+0xf/0x20 [<ffffffff8105c1db>] cpu_startup_entry+0x25b/0x360 [<ffffffff812c726e>] rest_init+0xbe/0xd0 [<ffffffff816a4dcb>] start_kernel+0x339/0x346 [<ffffffff816a4495>] x86_64_start_reservations+0x2a/0x2c [<ffffffff816a4589>] x86_64_start_kernel+0xf2/0xf6 HELP : loglevel(0-9) reboot(b) crash(c) show-all-locks(d) te... Before ebade5e833eda30 ("serial: 8250: Clean up the locking for -rt") this was handled by not even attempting to try the lock if port->sysrq, since it is known to be taken by the interrupt handler; see https://bugzilla.kernel.org/show_bug.cgi?id=6716#c1. Restore that behavior. Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-25serial: Fix io address assign flow with Fintek PCI-to-UART ProductPeter Hung
The original driver fixed the io address with 0xe000+idx*8, but real io address assigned from BIOS is dynamically from read PCI configure space 0x24, 0x20, 0x1c. The Fintek F81504/F81508/F81512 maybe malfunction without this patch and malfunction surely when more then 1 PCI card. Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-25serial: 8250_dw: Use 64-bit access for OCTEON.David Daney
Although the existing code appears to work on most hardware, the hardware designers tell us that 8-bit access to the registers is not guaranteed to be reliable. Also the OCTEON simulation environments prohibit 8-bit accesses. For these reasons, we use __raw_readq/__raw_writeq for OCTEON. This code is protected with #ifdef CONFIG_64BIT so it still builds under configurations lacking readq/writeq. We can get rid of the #ifdef __BIG_ENDIAN, as under 64-bit accesses, OCTEON is byte order invariant. Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-25tty: serial: 8250: omap: line is unsigned, don't check < 0Sebastian Andrzej Siewior
Dan Carpenter reported: |drivers/tty/serial/8250/8250_omap.c:1025 omap8250_probe() |warn: unsigned 'up.port.line' is never less than zero. |1025 if (up.port.line < 0) { I (wrongly) assumed that line is an int and compiler didn't complain nor did sparse. Since of_alias_get_id() and pdev->id can get negative I check for the error via ret variable. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial: 8250_core: actually limit char reads to max_countFrans Klaver
In serial8250_rx_chars(), max_count is set to 256. Due to the post-decrement operator used in the while() condition, the maximum number of iterations actually 257. This is not a problem, but it is mildly surprising if you're debugging. Use pre-decrement instead. Signed-off-by: Frans Klaver <frans.klaver@xsens.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial: 8250_dma: no need to set tx_err twiceAndy Shevchenko
In the serial8250_tx_dma() the tx_err flag is set in case of error. Thus, there is no need to repeat this in __dma_tx_complete(). Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial: 8250_dma: call serial8250_tx_dma unconditionallyAndy Shevchenko
Since we have the same check inside the function we may drop it away in __dma_tx_complete(). Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial/8250: Remove obsolete handling of rs485 ioctlsRicardo Ribalda Delgado
There is no more users for this functions. All the 8250 drivers are using the rs485 handler on serial_core instead. Reviewed-by: Alan Cox <alan@linux.intel.com> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Alan Cox <alan@linux.intel.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-068250/fintek: Use rs485 handler from serial_coreRicardo Ribalda Delgado
In order to remove the handler for rs485 ioctls on serial_8250, all the drivers must use the implementation on serial_core. Reviewed-by: Alan Cox <alan@linux.intel.com> Cc: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial/8250: Copy RS485 fields to serial_coreRicardo Ribalda Delgado
Initialize recently added rs485 fields on serial_core Reviewed-by: Alan Cox <alan@linux.intel.com> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Alan Cox <alan@linux.intel.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial: 8250: sparse warning of incorrect typeSudip Mukherjee
fixed a sparse warning in 8250_core.c : incorrect type in assignment (different address spaces) the warning was because an unsigned char pointer was being assigned to a pointer of unsigned char __iomem type . Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06parport: Add support for the WCH382 2S/1P multi-IO cardSergej Pupykin
WCH382 is a PCI-E card with 1 LPT and 2 DB9 COM ports detected as Serial controller: Device 1c00:3250 (rev 10) (prog-if 05 [16850]) Signed-off-by: Sergej Pupykin <ml@sergej.pp.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial: Test/disable MSIs if switching from N_PPSPeter Hurley
Switching to the N_PPS line discipline may require enabling modem status interrupts; conversely switching from N_PPS may require disabling modem status interrupts. Affected drivers: 8250 amba-pl010 atmel Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Russell King <linux@arm.linux.org.uk> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial: Take uart port lock for direct *_enable_ms()Peter Hurley
Three UART drivers (8250, atmel & amba-pl010) directly call their enable_ms() method; the uart port lock must be acquired before any h/w programming. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial: core: Pass termios to set_ldisc() notificationsPeter Hurley
UART drivers which enable modem status interrupts when switching to N_PPS line discipline need to determine if modem status interrupts should be disabled when switching from N_PPS. Specifically, the set_ldisc() notification needs to evaluate UART_ENABLE_MS() which requires termios->c_cflag. Convert in-tree UART drivers to new interface. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial: 8250_dw: get index of serial line from DT aliasesJulien CHAUVEAU
Get index of serial line from device tree using function of_alias_get_id(). If no alias is found, the 8250 core takes care of incrementing the line number. Signed-off-by: Julien CHAUVEAU <julien.chauveau@neo-technologies.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial: 8250_pci: Check mapping in pci_ni8430_initAaron Sierra
Check the return value of ioremap_nocache to make sure we got a valid mapping. Signed-off-by: Aaron Sierra <asierra@xes-inc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial: 8250_pci: Handle devices mapped above 4 GiBAaron Sierra
Several init/setup functions passed the PCI BAR resource start address to ioremap_nocache() via an unsigned long. This caused address truncation for a 32-bit device mapped above 4 GiB (i.e. the CPU interacts with the device via a translated address), which resulted in a kernel panic. This patch replaces all of the instances of intermediate variable use with pci_ioremap_bar() to ensure the full resource_size_t start address is used and that ioremap_nocache() is still called. The kernel panic (Exar XR17V358 PCIe device on a Freescale P2020 SBC): Machine check in kernel mode. Caused by (from MCSR=10008): Bus - Read Data Bus Error Oops: Machine check, sig: 7 [#1] SMP NR_CPUS=2 X-ES P2020 Modules linked in: CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.14.15-xes_r2-00002-g560e401 #978 task: bf850000 ti: bffee000 task.ti: bf84c000 NIP: 80318e10 LR: 80319ecc CTR: 80318dfc REGS: bffeff10 TRAP: 0204 Not tainted (3.14.15-xes_r2-00002-g560e401) MSR: 00021000 <CE,ME> CR: 20adbe42 XER: 00000000 DEAR: c1058001 ESR: 00000000 GPR00: 00000000 bf84db30 bf850000 80cb4af8 00000001 00000000 80000007 80000000 GPR08: bf837c9c c1058001 00000001 00000000 80000007 00000000 80002a10 00000000 GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 80cb0000 80c72dc4 GPR24: 80cb4900 fffffffe 00029000 00000001 bf8c11e8 ffffffea 80c72ce4 80cb4af8 NIP [80318e10] mem_serial_in+0x14/0x28 LR [80319ecc] serial8250_config_port+0x160/0xe38 Call Trace: [bf84db30] [80319d94] serial8250_config_port+0x28/0xe38 (unreliable) [bf84db60] [80315e3c] uart_add_one_port+0x148/0x3a4 [bf84dbf0] [8031bf40] serial8250_register_8250_port+0x2dc/0x3c8 [bf84dc20] [8032111c] pciserial_init_ports+0xd4/0x1c0 [bf84dd50] [803212f8] pciserial_init_one+0xf0/0x224 [bf84dd90] [802d8ff4] local_pci_probe+0x34/0x8c [bf84dda0] [802d92c8] pci_device_probe+0x84/0xa0 [bf84ddc0] [80329ee0] driver_probe_device+0xac/0x26c [bf84dde0] [8032a15c] __driver_attach+0xbc/0xc0 [bf84de00] [80328388] bus_for_each_dev+0x90/0xcc [bf84de30] [80329cd0] driver_attach+0x24/0x34 [bf84de40] [80328e28] bus_add_driver+0x104/0x1fc [bf84de60] [8032a8c8] driver_register+0x70/0x138 [bf84de70] [802d93c0] __pci_register_driver+0x48/0x58 [bf84de80] [8077e0e4] serial_pci_driver_init+0x24/0x34 [bf84de90] [80002228] do_one_initcall+0x34/0x1b0 [bf84df00] [80764294] kernel_init_freeable+0x138/0x1e8 [bf84df30] [80002a24] kernel_init+0x14/0x108 [bf84df40] [8000ef94] ret_from_kernel_thread+0x5c/0x64 Instruction dump: 800800c4 7d290214 39290001 7c0004ac 7ca049ae 7c0004ac 4e800020 88030035 81230008 7c840030 7d292214 7c0004ac <88690000> 0c030000 4c00012c 5463063e ---[ end trace e3c16443b5d573c6 ]--- Signed-off-by: Aaron Sierra <asierra@xes-inc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06tty: serial: Fix mediatek UART driver setting baudrate issueEddie Huang
In mtk8250_set_termios function, calculating quot value can not be zero, otherwise, using DIV_ROUND_CLOSEST(port->uartclk, quot * baud) will fail due to divisor is zero. Signed-off-by: Eddie Huang <eddie.huang@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial: ralink: adds Mediatek MT7620 serialJohn Crispin
Add the config symbol for Mediatek MT7620 SoC to the SERIAL_8250_RT288X dependencies. Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-06serial: of: add a PORT_RT2880 definitionJohn Crispin
The Ralink RT2880 SoC and its successors have an internal 8250 core. This core needs the same quirks applied as the AMD AU1xxx uart. In addition to these quirks, the ports memory region is only 0x100 unlike the AU1xxx which has a size of 0x1000. Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05serial: 8250_em: Remove out-of-memory messagePeter Hurley
devm_kzalloc() already warns if allocation fails; remove duplicate message. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05serial: hp300: Remove obsolete commentsPeter Hurley
setup_serial_console() is obsolete and has been superseded by early_serial_setup() which is called at the end of the function. The IA64 arch does not call this function; only the m68k arch setup calls this function. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05tty: serial: 8250_mtk: Fix quot calculationMatthias Brugger
The calculation of value quot for highspeed register set to three was wrong. This patch fixes the calculation so that the serial port for baudrates bigger then 576000 baud is working correctly. Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05serial: 8250_dw: Add DMA support for non-ACPI platformsRay Jui
The dma pointer under struct uart_8250_port is currently left unassigned for non-ACPI platforms. It should be pointing to the dma member in struct dw8250_data like how it was done for ACPI, so the core 8250 code will try to request for DMA when registering the port If DMA is not enabled in device tree, request DMA will fail and the driver will fall back to PIO Signed-off-by: Ray Jui <rjui@broadcom.com> Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com> Reviewed-by: Scott Branden <sbranden@broadcom.com> Tested-by: Scott Branden <sbranden@broadcom.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05tty: serial: 8250: omap: add dma supportSebastian Andrzej Siewior
This patch adds the required pieces to 8250-OMAP UART driver for DMA support. The TX burst size is set to 1 so we can send an arbitrary amount of bytes. The RX burst is currently set to 48 which means we receive an DMA interrupt every 48 bytes and have to reprogram everything. Less bytes in the RX-FIFO mean that no DMA transfer will happen and the UART will send a RX-timeout _or_ RDI event at which point the FIFO will be manually purged. There is a workaround for TX-DMA on AM33xx where we put the first byte into the FIFO to kick start the DMA process. Haven't seen this problem on OMAP36xx (beagle board xm) or DRA7xx. On AM375x there is "Usage Note 2.7: UART: Cannot Acknowledge Idle Requests in Smartidle Mode When Configured for DMA Operations" in the errata document. This problem persists even after disabling DMA in the UART and will be addressed in the HWMOD. v10: - delay update_registers() from set_termios() until TX-DMA is done. It has been reported / proved that invoking update_registers() while TX-DMA is in progress may stall the DMA operation and it won't finish. - use the new omap DMA-TX-RX hooks and DMA only interrupt routine. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05tty: serial: 8250: omap: add custom irq handlingSebastian Andrzej Siewior
We have (or will have) custom DMA callbacks in the omap driver due to the different behaviour in the RX and TX case. To make this work we need a few changes in the IRQ handler to invoke the rx_handler again after the "manual" mode or retry the tx_handler again before falling back to the manual mode. Heikki didn't want to see the extra hacks in the generic / default irq handler and Peter wasn't too happy about an OMAP-only IRQ handler. The way I planned it is to use this extra IRQ routine only in DMA case. If Peter dislike this approach then I hope Heikki doesn't block changes in the default IRQ handler :) Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05tty: serial: 8250_omap: add custom DMA-RX callbackSebastian Andrzej Siewior
The omap needs a DMA request pending right away. If it is enqueued once the bytes are in the FIFO then nothing will happen and the FIFO will be later purged via RX-timeout interrupt. This patch enqueues RX-DMA request on completion but not if it was aborted on error. The first enqueue will happen in the driver in startup. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05tty: serial: 8250_omap: add custom DMA-TX callbackSebastian Andrzej Siewior
This patch provides mostly a copy of serial8250_tx_dma() + __dma_tx_complete() with the following extensions: - DMA bug At least on AM335x the following problem exists: Even if the TX FIFO is empty and a TX transfer is programmed (and started) the UART does not trigger the DMA transfer. After $TRESHOLD number of bytes have been written to the FIFO manually the UART reevaluates the whole situation and decides that now there is enough room in the FIFO and so the transfer begins. This problem has not been seen on DRA7 or beagle board xm (OMAP3). I am not sure if this is UART-IP core specific or DMA engine. The workaround is to use a threshold of one byte, program the DMA transfer minus one byte and then to put the first byte into the FIFO to kick start the transfer. - support for runtime PM RPM is enabled on start_tx(). We can't disable RPM on DMA complete callback because there is still data in the FIFO which is being sent. We have to wait until the FIFO is empty before we disable it. For this to happen we fake a TX sent error and enable THRI. Once the FIFO is empty we receive an interrupt and since the TTY-buffer is still empty we "put RPM" via __stop_tx(). Should it been filed then in the start_tx() path we should program the DMA transfer and remove the error flag and the THRI bit. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05tty: serial: 8250: allow to use custom DMA implementationSebastian Andrzej Siewior
The OMAP has a few corner cases where it needs a share of kindness of affection to do the right thing. Heikki Krogerus suggested that instead adding the quirks into the default DMA implementation, OMAP could get its own copy of the function. And Alan suggested the same thing so here we go. This patch provides callbacks for custom TX/RX DMA implementation. If there are not setup / used, then the default (current) implementation is used. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05tty: serial: 8250_dma: keep own book keeping about RX transfersSebastian Andrzej Siewior
After dmaengine_terminate_all() has been invoked then both DMA drivers (edma and omap-dma) do not invoke dma_cookie_complete() to mark the transfer as complete. This dma_cookie_complete() is performed by the Synopsys DesignWare driver which is probably the only one that is used by omap8250-dma and hence don't see following problem… …which is that once a RX transfer has been terminated then following query of channel status reports DMA_IN_PROGRESS (again: the actual transfer has been canceled, there is nothing going on anymore). This means that serial8250_rx_dma() never enqueues another DMA transfer because it (wrongly) assumes that there is a transer already pending. Vinod Koul refuses to accept a patch which adds this dma_cookie_complete() to both drivers and so dmaengine_tx_status() would report DMA_COMPLETE instead (and behave like the Synopsys DesignWare driver already does). He argues that I am not allowed to use the cookie to query the status and that the driver already cleaned everything up after the invokation of dmaengine_terminate_all(). To end this I add a bookkeeping whether or not a RX-transfer has been started to the 8250-dma code. It has already been done for the TX side. *Now* we learn about the RX status based on our bookkeeping and don't need dmaengine_tx_status() for this anymore. Cc: vinod.koul@intel.com Reviewed-by: Tony Lindgren <tony@atomide.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05tty: serial: 8250_dma: handle error on TX submitSebastian Andrzej Siewior
Right now it is possible that serial8250_tx_dma() fails and returns -EBUSY. The caller (serial8250_start_tx()) will then enable UART_IER_THRI which will generate an interrupt once the TX FIFO is empty. In serial8250_handle_irq() nothing will happen because up->dma is set and so serial8250_tx_chars() won't be invoked. We end up with plenty of interrupts and some "too much work for irq" output. This patch introduces dma_tx_err in struct uart_8250_port to signal that the last invocation of serial8250_tx_dma() failed so we can fill the TX FIFO manually. Should the next invocation of serial8250_start_tx() succeed then the dma_tx_err flag along with the THRI bit is removed and DMA only usage may continue. Reviewed-by: Tony Lindgren <tony@atomide.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05tty: serial: Add 8250-core based omap driverSebastian Andrzej Siewior
This patch provides a 8250-core based UART driver for the internal OMAP UART. The long term goal is to provide the same functionality as the current OMAP uart driver and DMA support. I tried to merge omap-serial code together with the 8250-core code. There should should be hardly a noticable difference. The trigger levels are different compared to omap-serial: - omap serial TX: Interrupt comes after TX FIFO has room for 16 bytes. TX of 4096 bytes in one go results in 256 interrupts RX: Interrupt comes after there is on byte in the FIFO. RX of 4096 bytes results in 4096 interrupts. - this driver TX: Interrupt comes once the TX FIFO is empty. TX of 4096 bytes results in 65 interrupts. That means there will be gaps on the line while the driver reloads the FIFO. RX: Interrupt comes once there are 48 bytes in the FIFO or less over "longer" time frame. We have 1 / 11520 * 10^3 * 16 => 1.38… ms 1.38ms to react and purge the FIFO on 115200,8N1. Since the other driver fired after each byte it had ~5.47ms time to react. This _may_ cause problems if one relies on no missing bytes and has no flow control. On the other hand we get only 85 interrupts for the same amount of data. It has been only tested as console UART on am335x-evm, dra7-evm and beagle bone. I also did some longer raw-transfers to meassure the load. The device name is ttyS based instead of ttyO. If a ttyO based node name is required please ask udev for it. If both driver are activated (this and omap-serial) then this serial driver will take control over the device due to the link order v9…v10: - Tony noticed that omap3 won't show anything after waking up from core off. In v9 I reworked the register restore and set IER to 0 by accident. This went unnoticed because start_tx usually sets ier (either due to DMA bug or due to TX-complete IRQ). - dropped EFR and SLEEP from capabilities. We do have both but nobody should touch it. We already handle SLEEP ourself. - make the private copy of the registers (like EFR) u8 instead u32 - drop MDR1 & DL[ML] reset in restore registers. Does not look required it is set to the required value later. - update MDR1 & SCR only if changed. - set MDR1 as the last thing. The errata says that we should setup everything before MDR1 set. - avoid div by 0 in omap_8250_get_divisor() if baud rate gets very large (Frans Klaver fixed the same thing omap-serial) - drop "is in early stage" from Kconfig. v8…v9: - less on a file seems to hang the am335x after a while. I believe I introduce this bug a while ago since I can reproduce this prior to v8. Fixed by redoing the omap8250_restore_regs() v7…v8: - redo the register write. There is now one function for that which is used from set_termios() and runtime-resume. - drop PORT_OMAP_16750 and move the setup to the omap file. We have our own set termios function anyway (Heikki Krogerus) - use MEM instead of MEM32. TRM of AM/DM37x says that 32bit access on THR might result in data abort. We only need 32bit access in the errata function which is before we use 8250's read function so it doesn't matter. v4…v7: - change trigger levels after some tests with raw transfers. v3…v4: - drop RS485 support - wire up ->throttle / ->unthrottle v2…v3: - wire up startup & shutdown for wakeup-irq handling. - RS485 handling (well the core does). v1…v2: - added runtime PM. Could somebody could please double check this? - added omap_8250_set_termios() Reviewed-by: Tony Lindgren <tony@atomide.com> Tested-by: Tony Lindgren <tony@atomide.com> Tested-by: Frans Klaver <frans.klaver@xsens.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05tty: serial: 8250: make serial8250_console_setup() non _initSebastian Andrzej Siewior
if I boot with console=ttyS0 and the omap driver is module I end up with | console [ttyS0] disabled | omap8250 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a 8250 | Unable to handle kernel paging request at virtual address c07a9de0 | Modules linked in: 8250_omap(+) | CPU: 0 PID: 908 Comm: modprobe Not tainted 3.17.0-rc5+ #1593 | PC is at serial8250_console_setup+0x0/0xc8 | LR is at register_console+0x13c/0x3a4 | [<c0078788>] (register_console) from [<c02d0340>] (uart_add_one_port+0x3cc/0x420) | [<c02d0340>] (uart_add_one_port) from [<c02d38a4>] (serial8250_register_8250_port+0x298/0x39c) | [<c02d38a4>] (serial8250_register_8250_port) from [<bf006274>] (omap8250_probe+0x218/0x3dc [8250_omap]) | [<bf006274>] (omap8250_probe [8250_omap]) from [<c02e3424>] (platform_drv_probe+0x2c/0x5c) | [<c02e3424>] (platform_drv_probe) from [<c02e1eac>] (driver_probe_device+0x104/0x228) … | [<c009fa48>] (SyS_init_module) from [<c000e6e0>] (ret_fast_syscall+0x0/0x30) | Code: 7823603b f8314620 051b3013 491ed416 (44792204) because serial8250_console_setup() is already gone. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05tty: serial: 8250: Fix wording in runtime-PM commentsSebastian Andrzej Siewior
Frans reworded the two comments with better English for better understanding. His review hit the mailing list after the patch got applied so here is an incremental update. Reported-by: Frans Klaver <frans.klaver@xsens.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-058250_pci: Added driver for Endrun Technologies PTP PCIe card.Mike Skoog
Added recognition of EndRun Technologies PCIe PTP slave card and setup two ttySx ports for communication with the card for retrieval of PTP based time and to communicate with the card's Linux OS. Signed-off-by: Mike Skoog <mskoog@endruntechnologies.com> Signed-off-by: Mike Korreng <mkorreng@endruntechnologies.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05tty: serial: 8250_core: restore the LCR register in set_sleepSudhir Sreedharan
In ST16650V2 based serial uarts, while initalizing the PM state, LCR registers are being initialized to 0 in serial8250_set_sleep(). If console port is already initialized and being used, this will throws garbage in the console. Signed-off-by: Sudhir Sreedharan <ssreedharan@mvista.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Tested-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-20tty: serial: 8250: drop owner assignment from platform_driversWolfram Sang
A platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-18Merge branch 'for-linus' of git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds
Pull slave-dmaengine updates from Vinod Koul: "For dmaengine contributions we have: - designware cleanup by Andy - my series moving device_control users to dmanegine_xxx APIs for later removal of device_control API - minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma etc" * 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits) serial: atmel: add missing dmaengine header dmaengine: remove FSLDMA_EXTERNAL_START dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method carma-fpga: move to fsl_dma_external_start() carma-fpga: use dmaengine_xxx() API dmaengine: freescale: add and export fsl_dma_external_start() dmaengine: add dmaengine_prep_dma_sg() helper video: mx3fb: use dmaengine_terminate_all() API serial: sh-sci: use dmaengine_terminate_all() API net: ks8842: use dmaengine_terminate_all() API mtd: sh_flctl: use dmaengine_terminate_all() API mtd: fsmc_nand: use dmaengine_terminate_all() API V4L2: mx3_camer: use dmaengine_pause() API dmaengine: coh901318: use dmaengine_terminate_all() API pata_arasan_cf: use dmaengine_terminate_all() API dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause() dmaengine: dw: export probe()/remove() and Co to users dmaengine: dw: enable and disable controller when needed dmaengine: dw: always export dw_dma_{en,dis}able dmaengine: dw: introduce dw_dma_on() helper ...
2014-10-08Merge tag 'tty-3.18-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial driver updates from Greg KH: "Here's the big tty/serial driver patchset for 3.18-rc1. Lots of little things in here, some good work from Peter Hurley on the tty core, and in lots of drivers. There are also lots of other driver updates in here as well, full details in the changelogs. All have been in the linux-next tree for a while" * tag 'tty-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (99 commits) Revert "serial/core: Initialize the console pm state" tty: serial: 8250: use 32bit variable for rpm_tx_active tty: serial: msm: Add earlycon support serial/core: Initialize the console pm state serial: asc: Conditionally use readl_relaxed (COMPILE_TEST) serial: of-serial: add PM suspend/resume support m68k: AMIGA_BUILTIN_SERIAL should depend on TTY asm/uapi: Add definition of TIOC[SG]RS485 tty/metag_da: Add console_poll module parameter serial: 8250_pci: remove rts_n override from Baytrail quirk serial: cadence: Add generic earlycon support serial: imx: change the wait even to interruptiable serial: imx: terminate the RX DMA when the UART is suspending serial: imx: fix throttle/unthrottle callbacks for hardware assisted flow control serial: 8250: Add Quark X1000 to 8250_pci.c tty: omap-serial: pull out calculation from baud_is_mode16 tty: omap-serial: fix division by zero xen_hvc: no reason to write the type key on xenstore tty: serial: 8250_core: remove UART_IER_RDI in serial8250_stop_rx() tty: serial: 8250_core: use the ->line argument as a hint in serial8250_find_match_or_unused() ...
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-02 05:40:31 +0000