| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Commit b82715fdd4a5407f56853b24d387d484dd9c3b5b introduces
a 'device' subdirectory under /sys/class/hwmon/hwmonX/ directory,
for the thermal_zone hwmon devices. And this results in different
handling by libsensors.
The problem is reported and discussed in this thread
http://marc.info/?l=linux-pm&m=138229306109596&w=2
This patch reverts commit b82715fdd4a5407f56853b24d387d484dd9c3b5b.
Reported-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
This patch changes the behavior of TI SoC thermal driver
when there is a PCB thermal zone.
Instead of reporting an error code when reading from
PCB temperature sensor fails, this patch will make
the driver attempt to compose the hotspot extrapolation
based on bandgap readings only.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
Exynos4412
The commit d0a0ce3e77c795258d47f9163e92d5031d0c5221 ("thermal: exynos: Add
missing definations and code cleanup") has removed setting of test MUX address
value at TMU configuration setting.
This field is not present on Exynos4210 and Exynos5 SoCs. However on Exynos4412
SoC it is required to set this field after reset because without it TMU shows
maximal available temperature, which causes immediate platform shutdown.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
Up till now Exynos5250 and Exynos4412 had the same definitions for TMU
data. Following commit changes that, by introducing separate
exynos4412_default_tmu_data structure.
Since Exynos4412 was chronologically first, the corresponding name for
TMU registers and default data was renamed.
Additionally, new SOC_ARCH_EXYNOS4412 type has been defined.
Moreover, the SOC_ARCH_EXYNOS name has been changed to SOC_ARCH_EXYNOS5250.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
exynos_report_trigger()
The commit 4de0bdaa9677d11406c9becb70c60887c957e1f0
("thermal: exynos: Add support for instance based register/unregister")
broke check for presence of therm_dev at global thermal zone in
exynos_report_trigger().
The resulting wrong test prevents thermal_zone_device_update() call, which
calls handlers for situation when trip points are passed.
Such behavior prevents thermal driver from proper reaction (when TMU interrupt
is raised) in a situation when overheating is detected at TMU hardware.
It turns out, that after exynos thermal subsystem redesign (at v3.12) this
check is not needed, since it is not possible to register thermal zone
without valid thermal device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
x86_pkg_temp receives thermal notifications via a callback from a
therm_throt driver, where thermal interrupts are processed.
This callback is pkg_temp_thermal_platform_thermal_notify. Here to
avoid multiple interrupts from cores in a package, we disable the
source and also set a variable to avoid scheduling delayed work function.
This variable is protected via spin_lock_irqsave. On one buggy platform,
we still receiving interrupts even if the source is disabled. This
can cause deadlock/lockdep warning, when interrupt is generated while under
spinlock in work function.
Change spin_lock to spin_lock_irqsave and spin_unlock to
spin_unlock_irqrestore as the data it is trying to protect can also
be modified in a notification call called from interrupt handler.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
This patch avoids NULL pointer accesses while unregistering
cpu cooling devices, in case a NULL pointer is received.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
When registering a thermal zone device using platform information
via bind_params, the thermal framework will always perform the
cdev binding using the lowest and highest limits (THERMAL_NO_LIMIT).
This patch changes the data structures so that it is possible
to inform what are the desired limits for each trip point
inside a bind_param. The way the binding is performed is also
changed so that it uses the new data structure.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
When registering a new thermal_device, the thermal framework
will always add a hwmon sysfs interface.
This patch adds a flag to make this behavior optional. Now
when registering a new thermal device, the caller can
optionally inform if hwmon interface is desirable. This can
be done by means of passing a thermal_zone_params.no_hwmon == true.
In order to keep same behavior as of today, all current
calls will by default create the hwmon interface.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-acpi@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: Zhang Rui <rui.zhang@intel.com>
Suggested-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
When creating virtual hwmon devices based out of thermal
zone devices, the virtual devices won't have parents.
This patch changes the code so that the parent of virtual
hwmon devices is the thermal zone device that they are
based of.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
In order to improve code organization, this patch
moves the hwmon sysfs support to a file named
thermal_hwmon. This helps to add extra support
for hwmon without scrambling the code.
In order to do this move, the hwmon list head is now
using its own locking. Before, the list used
the global thermal locking. Also, some minor changes
in the code were required, as recommended by checkpatch.pl.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
Commit 1cd1ecb6 ("thermal: exynos: Remove non DT based support")
cleaned up some non-DT code. However, there were few more things
needed for complete cleanup to make this driver DT only.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
NULL pointer was being dereferenced in its own error message.
Changed it to the correct device pointer.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
Fixes some trivial typos.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
Workaround to compute thermal trend even when update interval
is not set. This patch will ensure to compute the thermal trend
when bandgap counter delay is not set.
Signed-off-by: Ranganath Krishnan <ranganath@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
Set the bandgap mask counter_delay with the polling_delay value on
registering the thermal zone. This patch will ensure to get the
correct update interval for computing the thermal trend.
Signed-off-by: Ranganath Krishnan <ranganath@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
Initialize MPU, GPU, CORE, DSPEVE and IVA thermal sensors of DRA752 bandgap
with the counter delay mask.
Signed-off-by: Ranganath Krishnan <ranganath@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
|
|
In case the trend is not changing or when there is no
request for throttling, it is expected that the instance
would not change its requested target. This patch improves
the code implementation to cover for this expected behavior.
With current implementation, the instance will always
reset to cdev.cur_state, even in not expected cases,
like those mentioned above.
This patch changes the step_wise governor implementation
of get_target so that we accomplish:
(a) - default value will be current instance->target, so
we do not change the thermal instance target unnecessarily.
(b) - the code now it is clear about what is the intention.
There is a clear statement of what are the expected outcomes
(c) - removal of hardcoded constants, now it is put in use
the THERMAL_NO_TARGET macro.
(d) - variable names are also improved so that reader can
clearly understand the difference between instance cur target,
next target and cdev cur_state.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reported-by: Ruslan Ruslichenko <ruslan.ruslichenko@ti.com>
Signed-of-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
The cooling device only needs update on a new target state. Since we
already check old target in thermal_zone_trip_update(), we can do one
more check to see if it's a new target state. If not, we can reasonably
save some uncecesary code execution.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
|
|
cpufreq_thermal_notifier()
cpufreq_thermal_notifier() is to change the cpu's cpufreq in the allowed_cpus mask
when associated thermal-cpufreq cdev's cooling state is changed. It's a cpufreq policy
notifier handler and it will be triggered even if those cpus out of allowed_cpus has
changed freq policy.
cpufreq_thermal_notifier() checks the policy->cpu. If it belongs to allowed_cpus,
change max_freq(default to 0) to the desire cpufreq value and pass 0 and max_freq
to cpufreq_verify_within_limits() as cpufreq scope. But if not, do nothing and
max_freq will remain 0. This will cause the cpufreq scope to become 0~0. This
is not right. This patch is to return directly after finding cpu not belonging
to allowed_cpus.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
The error check is checking for a "base" mapped memory base
instead of "base_common". Fixing the same.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Enable automatic measurements at 10 Hz and use the alarm interrupt to react
more quickly to sudden temperature changes above the passive or critical
temperature trip points.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Set passive and critical trip point values depending on the maximum die
temperature stored in the OCOTP fuses. This allows higher trip points
for industrial and automotive rated i.MX6 SoCs.
Also allow to configure the passive trip point from userspace.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
TMU probe function now checks for a device tree defined regulator.
For compatibility reasons it is allowed to probe driver even without
this regulator defined.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch adds support for h/w mode calibration in the TMU controller.
Soc's like 5440 support this features. The h/w bits needed for calibration
setting are same as that of enum calibration_type.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch sets the second point trimming value according to the platform
data if the register value is 0.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch adds configuration data for exynos5440 soc. Also register
definations for the controller are added.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch modifies TMU controller to add changes needed to work with
exynos5440 platform. This sensor registers 3 instance of the tmu controller
with the thermal zone and hence reports 3 temperature output. This controller
supports upto five trip points. For critical threshold the driver uses the
core driver thermal framework for shutdown.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Jungseok Lee <jays.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch adds support to parse one more common set of TMU register. First
set of register belongs to each instance of TMU and second set belongs to
common TMU registers.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch uses the device pointer stored in the configuration structure
and converts to dev_* prints and devm API's.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch adds several features supported by TMU as bitfields.
This features varies across different SOC type and comparing
the features present in the TMU is more logical than comparing
the soc itself.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch adds support to handle multiple instances of the TMU controllers.
This is done by removing the static structure to register with the core thermal
and creating it dynamically for each instance of the TMU controller. The
interrupt is made shared type to handle shared interrupts. Now since the ISR needs
the core thermal framework to be registered so request_irq is moved after the core
registration is done.
Also the identifier of the TMU controller is extracted from device tree alias. This
will be used for TMU specific initialisation.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
Recently non DT support from Exynos platform is removed and hence
removing non DT support from the driver also. This will help in easy
maintainence.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This code simplifies the zone handling to use the trip information passed
by the TMU driver and not the hardcoded macros. This also helps in adding
more zone support.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch removes the error return in the bind/unbind routine
as the platform may not register any cpufreq cooling data.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch renames member private_data to driver_data of the thermal
zone registration structure as this item stores the driver related
data and uses it to call the driver related callbacks.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This code modifies the thermal driver to have multiple thermal zone
support by replacing the global thermal zone variable with device data
member of thermal_zone_device.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch uses the TMU status register to know the generated interrupts
and only clear them in the interrupt handler.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
TMU urgently sends active-high signal (thermal trip) to PMU, and thermal
tripping by hardware logic. Thermal tripping means that PMU cuts off the
whole power of SoC by controlling external voltage regulator.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch migrates the TMU register definition/bitfields to data file. This
is needed to support SoC's which use the same TMU controller but register
validity, offsets or bitfield may slightly vary across SOC's.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch adds entries min_efuse_value, max_efuse_value, default_temp_offset,
trigger_type, cal_type, trim_first_point, trim_second_point, max_trigger_level
trigger_enable in the TMU platform data structure. Also the driver is modified
to use the data passed by these new platform memebers instead of the constant
macros. All these changes helps in separating the SOC specific data part from
the TMU driver.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch adds some extra register bitfield definations and cleans
up the code to prepare for moving register macros and definations inside
the TMU data section. In this code cleanup the TMU enable bit is correctly used
as bit0 and bit1 is taken care which is reserve bit.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This code splits the exynos tmu driver code into SOC specific data parts.
This will simplify adding new SOC specific data to the same TMU controller.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch renames and moves include/linux/platform_data/exynos_thermal.h to
drivers/thermal/samsung/exynos_tmu.h. This file movement is needed as exynos
SOC's are not supporting non-DT based platforms and this file now just contains
exynos tmu driver related definations.
Also struct freq_clip_table is now moved to exynos_thermal_common.c as it fixes
the compilation issue occuring because now this new tmu header file is included
in tmu driver c file and not in the common thermal header file.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch renames exynos_thermal.c to exynos_tmu.c. This change is needed as
this file now just contains exynos tmu driver related codes and thermal zone
or cpufreq cooling registration related changes are not there anymore.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This code bifurcates exynos thermal implementation into common and sensor
specific parts. The common thermal code interacts with core thermal layer and
core cpufreq cooling parts and is independent of SOC specific driver. This
change is needed to cleanly add support for new TMU sensors.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch removes the dependency on CPU_THERMAL for compiling TMU driver.
This is useful for cases when only TMU controller needs to be initialised
without cpu cooling action.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
