| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
"We only have a couple of fixes/cleanups for platform thermal drivers
this time.
Specifics:
- rcar thermal driver: avoid updating the thermal zone in case an IRQ
was triggered but the temperature didn't effectively change. From
Patrick Titiano.
- update the imx thermal driver' formula of converting thermal
sensor' raw date to real temperature in degree C. From Anson
Huang.
- trivial code cleanups of ti soc thermal and rcar thermal driver
from Jingoo Han and Patrick Titiano"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: rcar-thermal: update thermal zone only when temperature changes
thermal: rcar-thermal: fix same mask applied twice
thermal: ti-soc-thermal: Use SIMPLE_DEV_PM_OPS macro
thermal: imx: update formula for thermal sensor
|
|
Avoid updating the thermal zone in case an IRQ was triggered but the
temperature didn't effectively change.
Note this is not a driver issue.
Below is a captured debug trace illustrating the purpose of this patch:
out of 8 thermal zone updates, only 2 are actually necessary.
[ 41.120000] rcar_thermal_work(): cctemp=25000
[ 41.120000] rcar_thermal_work(): nctemp=30000
[ 41.120000] rcar_thermal_work(): temp is now 30000C, update thermal zone
[ 58.990000] rcar_thermal_work(): cctemp=30000
[ 58.990000] rcar_thermal_work(): nctemp=30000
[ 58.990000] rcar_thermal_work(): same temp, do not update thermal zone
[ 59.290000] rcar_thermal_work(): cctemp=30000
[ 59.290000] rcar_thermal_work(): nctemp=30000
[ 59.290000] rcar_thermal_work(): same temp, do not update thermal zone
[ 59.590000] rcar_thermal_work(): cctemp=30000
[ 59.590000] rcar_thermal_work(): nctemp=30000
[ 59.590000] rcar_thermal_work(): same temp, do not update thermal zone
[ 59.890000] rcar_thermal_work(): cctemp=30000
[ 59.890000] rcar_thermal_work(): nctemp=30000
[ 59.890000] rcar_thermal_work(): same temp, do not update thermal zone
[ 60.190000] rcar_thermal_work(): cctemp=30000
[ 60.190000] rcar_thermal_work(): nctemp=30000
[ 60.190000] rcar_thermal_work(): same temp, do not update thermal zone
[ 60.490000] rcar_thermal_work(): cctemp=30000
[ 60.490000] rcar_thermal_work(): nctemp=30000
[ 60.490000] rcar_thermal_work(): same temp, do not update thermal zone
[ 60.790000] rcar_thermal_work(): cctemp=30000
[ 60.790000] rcar_thermal_work(): nctemp=35000
[ 60.790000] rcar_thermal_work(): temp is now 35000C, update thermal zone
I suspect this may be due to sensor sampling accuracy / fluctuation,
but no formal proof.
Signed-off-by: Patrick Titiano <ptitiano@baylibre.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Mask is already applied preceding the if statement.
Remove the second mask.
Signed-off-by: Patrick Titiano <ptitiano@baylibre.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Thermal sensor used to need two calibration points which are
in fuse map to get a slope for converting thermal sensor's raw
data to real temperature in degree C. Due to the chip calibration
limitation, hardware team provides an universal formula to get
real temperature from internal thermal sensor raw data:
Slope = 0.4297157 - (0.0015976 * 25C fuse);
Update the formula, as there will be no hot point calibration
data in fuse map from now on.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CPU hotplug notifiers registration fixes from Rafael Wysocki:
"The purpose of this single series of commits from Srivatsa S Bhat
(with a small piece from Gautham R Shenoy) touching multiple
subsystems that use CPU hotplug notifiers is to provide a way to
register them that will not lead to deadlocks with CPU online/offline
operations as described in the changelog of commit 93ae4f978ca7f ("CPU
hotplug: Provide lockless versions of callback registration
functions").
The first three commits in the series introduce the API and document
it and the rest simply goes through the users of CPU hotplug notifiers
and converts them to using the new method"
* tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
net/iucv/iucv.c: Fix CPU hotplug callback registration
net/core/flow.c: Fix CPU hotplug callback registration
mm, zswap: Fix CPU hotplug callback registration
mm, vmstat: Fix CPU hotplug callback registration
profile: Fix CPU hotplug callback registration
trace, ring-buffer: Fix CPU hotplug callback registration
xen, balloon: Fix CPU hotplug callback registration
hwmon, via-cputemp: Fix CPU hotplug callback registration
hwmon, coretemp: Fix CPU hotplug callback registration
thermal, x86-pkg-temp: Fix CPU hotplug callback registration
octeon, watchdog: Fix CPU hotplug callback registration
oprofile, nmi-timer: Fix CPU hotplug callback registration
intel-idle: Fix CPU hotplug callback registration
clocksource, dummy-timer: Fix CPU hotplug callback registration
drivers/base/topology.c: Fix CPU hotplug callback registration
acpi-cpufreq: Fix CPU hotplug callback registration
zsmalloc: Fix CPU hotplug callback registration
scsi, fcoe: Fix CPU hotplug callback registration
scsi, bnx2fc: Fix CPU hotplug callback registration
scsi, bnx2i: Fix CPU hotplug callback registration
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
|
|
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the thermal x86-pkg-temp code by using this latter form of callback
registration.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch does a cleanup about the thermal zone govenor,
setting and make the following rule.
1. For thermal zone devices that are registered w/o tz->tzp,
they can use the default thermal governor only.
2. For thermal zone devices w/ governor name specified in
tz->tzp->governor_name, we will use the default govenor
if the governor specified is not available at the moment,
and update tz->governor when the matched governor is registered.
This also fixes a problem that OF registered thermal zones
are running with no governor.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Javi Merino <javi.merino@arm.com>
|
|
In initialization, if the cooling device is initialized at
max cooling state, and the thermal zone temperature is below
the first trip point, then the cooling state can't be updated
to the right state, untill the first trip point be triggered.
To fix this issue, allow first update of cooling device state
during registration, initialized "updated" device field as
"false" (instead of "true").
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Commit beeb5a1e (thermal: rcar-thermal: Enable driver compilation with COMPILE_TEST)
broke build on archs wihout io memory.
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/thermal/rcar_thermal.c:404: undefined reference to `devm_ioremap_resource'
drivers/thermal/rcar_thermal.c:426: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
The thermal zone type should not include an instance number. Otherwise
each zone is considered a different type and the thermal-to-hwmon
bridge fails to group them all in a single hwmon device.
I also changed the type to "x86_pkg_temp", because "pkg" was too
generic, and other thermal drivers use an underscore, not a dash, as
a separator. Or maybe "cpu_pkg_temp" would be better?
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
The temperature value reported by x86_pkg_temp_thermal is already
reported by the coretemp driver. So, do not expose this thermal zone
as a hwmon device, because it would be redundant.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
With the move of kirkwood into mach-mvebu, drivers Kconfig need
tweeking to allow the kirkwood specific drivers to be built.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
"This time, the biggest change is the work of representing hardware
thermal properties in device tree infrastructure.
This work includes the introduction of a device tree bindings for
describing the hardware thermal behavior and limits, and also a parser
to read and interpret the data, and build thermal zones and thermal
binding parameters. It also contains three examples on how to use the
new representation on sensor devices, using three different drivers to
accomplish it. One driver is in thermal subsystem, the TI SoC
thermal, and the other two drivers are in hwmon subsystem.
Actually, this would be the first step of the complete work because we
still need to check other potential drivers to be converted and then
validate the proposed API. But the reason why I include it in this
pull request is that, first, this change does not hurt any others
without using this approach, second, the principle and concept of this
change would not break after converting the remaining drivers. BTW,
as you can see, there are several points in this change that do not
belong to thermal subsystem. Because it has been suggested by Guenter
R that in such cases, it is recommended to send the complete series
via one single subsystem.
Specifics:
- representing hardware thermal properties in device tree
infrastructure
- fix a regression that the imx thermal driver breaks system suspend.
- introduce ACPI INT3403 thermal driver to retrieve temperature data
from the INT3403 ACPI device object present on some systems.
- introduce debug statement for thermal core and step_wise governor.
- assorted fixes and cleanups for thermal core, cpu cooling, exynos
thrmal, intel powerclamp and imx thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: remove const flag from .ops of imx thermal
Thermal: update thermal zone device after setting emul_temp
intel_powerclamp: Fix cstate counter detection.
thermal: imx: add necessary clk operation
Thermal cpu cooling: return error if no valid cpu frequency entry
thermal: fix cpu_cooling max_level behavior
thermal: rcar-thermal: Enable driver compilation with COMPILE_TEST
thermal: debug: add debug statement for core and step_wise
thermal: imx_thermal: add module device table
drivers: thermal: Mark function as static in x86_pkg_temp_thermal.c
thermal:samsung: fix compilation warning
thermal: imx: correct suspend/resume flow
thermal: exynos: fix error return code
Thermal: ACPI INT3403 thermal driver
MAINTAINERS: add thermal bindings entry in thermal domain
arm: dts: make OMAP4460 bandgap node to belong to OCP
arm: dts: make OMAP443x bandgap node to belong to OCP
arm: dts: add cooling properties on omap5 cpu node
arm: dts: add omap5 thermal data
arm: dts: add omap5 CORE thermal data
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
|
|
Exynos4412)
This patch provides auto disable/enable operation for boost. It uses already
present thermal infrastructure to provide BOOST hysteresis.
The TMU data is modified to work properly with or without BOOST.
Hence, the two first trip points with corresponding clip frequencies are
adjusted.
The first one is reduced from 85 to 70 degrees and the clip frequency is
increased to 1.4 GHz from 800 MHz. This trip point is in fact responsible
for providing BOOST hysteresis. When temperature exceeds 70 deg, the maximal
non BOOST frequency for Exynos4412 is imposed.
Since the first trigger level has been "stolen" for BOOST, the second one
needs to be a compromise for the previously used two for non BOOST
configuration. The 95 deg with modified clip freq (to 400 MHz) should provide
a good balance between cooling down the overheated device and throughput on
an acceptable level.
Two last trigger levels are not modified since, they cause platform shutdown
on emergency overheat to happen.
The third trip point passage results in SW managed shut down of the system.
If the last trip point is crossed, the PMU HW generates the power off
signal.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The only valid use of preempt_enable_no_resched() is if the very next
line is schedule() or if we know preemption cannot actually be enabled
by that statement due to known more preempt_count 'refs'.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: rjw@rjwysocki.net
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: rui.zhang@intel.com
Cc: jacob.jun.pan@linux.intel.com
Cc: Mike Galbraith <bitbucket@online.de>
Cc: hpa@zytor.com
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: lenb@kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-zcfvacdlvlr63qmnn5i58vuj@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
|
|
As per previous changes on thermal framework API,
registering a new thermal zone does not require
a const thermal zone ops.
Thus, this patch removes the flag from imx thermal zone ops.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
|
|
This patch is to update thermal zone device after setting emul_temp
in order to make governor work according to input temperature immediately.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Having all zero cstate count doesn't necesserily mean the cstate
counter is no functional.
Signed-off-by: Yuxuan Shui <yshuiv7@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Thermal sensor needs pll3_usb_otg when measuring temperature,
otherwise the temperature read will be incorrect, so need to
enable this clk before sensor working, for alarm function,
as hardware will take measurement periodically, so we should
keep this clk always on once alarm function is enabled.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
into next
|
|
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
As per Documentation/thermal/sysfs-api.txt, max_level
is an index, not a counter. Thus, in case a CPU has
3 valid frequencies, max_level is expected to be 2, for instance.
The current code makes max_level == number of valid frequencies,
which is bogus. This patch fix the cpu_cooling device by
ranging max_level properly.
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
This helps increasing build testing coverage.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
To ease debugging thermal problem, add these dynamic debug statements
so that user do not need rebuild kernel to see these info.
Based on a patch from Zhang Rui for debugging on bugzilla:
https://bugzilla.kernel.org/attachment.cgi?id=98671
A sample output after we turn on dynamic debug with the following cmd:
# echo 'module thermal_sys +fp' > /sys/kernel/debug/dynamic_debug/control
is like:
[ 355.147627] update_temperature: thermal thermal_zone0: last_temperature=52000, current_temperature=55000
[ 355.147636] thermal_zone_trip_update: thermal thermal_zone0: Trip1[type=1,temp=79000]:trend=2,throttle=0
[ 355.147644] get_target_state: thermal cooling_device8: cur_state=0
[ 355.147647] thermal_zone_trip_update: thermal cooling_device8: old_target=-1, target=-1
[ 355.147652] get_target_state: thermal cooling_device7: cur_state=0
[ 355.147655] thermal_zone_trip_update: thermal cooling_device7: old_target=-1, target=-1
[ 355.147660] get_target_state: thermal cooling_device6: cur_state=0
[ 355.147663] thermal_zone_trip_update: thermal cooling_device6: old_target=-1, target=-1
[ 355.147668] get_target_state: thermal cooling_device5: cur_state=0
[ 355.147671] thermal_zone_trip_update: thermal cooling_device5: old_target=-1, target=-1
[ 355.147678] thermal_zone_trip_update: thermal thermal_zone0: Trip2[type=0,temp=90000]:trend=1,throttle=0
[ 355.147776] get_target_state: thermal cooling_device0: cur_state=0
[ 355.147783] thermal_zone_trip_update: thermal cooling_device0: old_target=-1, target=-1
[ 355.147792] thermal_zone_trip_update: thermal thermal_zone0: Trip3[type=0,temp=80000]:trend=1,throttle=0
[ 355.147845] get_target_state: thermal cooling_device1: cur_state=0
[ 355.147849] thermal_zone_trip_update: thermal cooling_device1: old_target=-1, target=-1
[ 355.147856] thermal_zone_trip_update: thermal thermal_zone0: Trip4[type=0,temp=70000]:trend=1,throttle=0
[ 355.147904] get_target_state: thermal cooling_device2: cur_state=0
[ 355.147908] thermal_zone_trip_update: thermal cooling_device2: old_target=-1, target=-1
[ 355.147915] thermal_zone_trip_update: thermal thermal_zone0: Trip5[type=0,temp=60000]:trend=1,throttle=0
[ 355.147963] get_target_state: thermal cooling_device3: cur_state=0
[ 355.147967] thermal_zone_trip_update: thermal cooling_device3: old_target=-1, target=-1
[ 355.147973] thermal_zone_trip_update: thermal thermal_zone0: Trip6[type=0,temp=55000]:trend=1,throttle=1
[ 355.148022] get_target_state: thermal cooling_device4: cur_state=0
[ 355.148025] thermal_zone_trip_update: thermal cooling_device4: old_target=-1, target=1
[ 355.148036] thermal_cdev_update: thermal cooling_device4: zone0->target=1
[ 355.169279] thermal_cdev_update: thermal cooling_device4: set to state 1
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Add the module device table declaration so the module can be loaded
automatically at boot time.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Mark function sys_set_trip_temp() as static in x86_pkg_temp_thermal.c
because it is not used outside this file.
This eliminates the following warning in x86_pkg_temp_thermal.c:
drivers/thermal/x86_pkg_temp_thermal.c:218:5: warning: no previous prototype for ‘sys_set_trip_temp’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
This patch fixes a compilation warning.
warning: passing argument 5 of 'thermal_zone_device_register' discards 'const'
qualifier from pointer target type [enabled by default]
include/linux/thermal.h:270:29: note: expected 'struct thermal_zone_device_ops *'
but argument is of type 'const struct thermal_zone_device_ops *'
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Fixes regression introduced by:
commit 37713a1e8e4c1a1067ad4c99296f78d3c82ed9c4
Author: Philipp Zabel <p.zabel@pengutronix.de>
Date: Thu Aug 1 18:33:12 2013 +0200
thermal: imx: implement thermal alarm interrupt handling
The commit 37713a1e8e4 makes imx thermal sensor always powered up as alarm
function is enabled, but the suspend callback of imx thermal returns
success only if thermal sensor is powered down, so it will always returns
fail hence break system's suspend, this patch disables imx thermal sensor
before suspend and re-enable it after resume.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
The ACPI INT3403 device objects present on some systems can be used to retrieve
temperature data from thermal sensors. Add a driver registering each INT3403
device object as a thermal zone device and exposing its _TMP, PATx and GTSH
method via the standard thermal control interface under /sys/class/thermal/.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
People seem to delight in writing wrong and broken mwait idle routines;
collapse the lot.
This leaves mwait_play_dead() the sole remaining user of __mwait() and
new __mwait() users are probably doing it wrong.
Also remove __sti_mwait() as its unused.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jacob Jun Pan <jacob.jun.pan@linux.intel.com>
Cc: Mike Galbraith <bitbucket@online.de>
Cc: Len Brown <lenb@kernel.org>
Cc: Rui Zhang <rui.zhang@intel.com>
Acked-by: Rafael Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20131212141654.616820819@infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
This patch improves the ti-soc-thermal driver by adding the
support to build the thermal zones based on DT nodes.
The driver will have two options now to build the thermal
zones. The first option is the zones originally coded
in this driver. So, the driver behavior will be same
if there is no DT node describing the zones. The second
option, when it is found a DT node with thermal data,
will used the common infrastructure to build the thermal
zone and bind its cooling devices.
In case the driver loads thermal data using the legacy
mode, this driver still adds to the system
a cpufreq cooling device. Loading the thermal data from
DT, the driver assumes someone else will add the cpufreq
cooling device, like the cpufreq driver.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch introduces an API to register cpufreq cooling device
based on device tree node.
The registration via device tree node differs from normal
registration due to the fact that it is needed to fill
the device_node structure in order to be able to match
the cooling devices with trip points.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch adds a new API to allow registering cooling devices
in the thermal framework derived from device tree nodes.
This API links the cooling device with the device tree node
so that binding with thermal zones is possible, given
that thermal zones are pointing to cooling device
device tree nodes.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch introduces a device tree bindings for
describing the hardware thermal behavior and limits.
Also a parser to read and interpret the data and feed
it in the thermal framework is presented.
This patch introduces a thermal data parser for device
tree. The parsed data is used to build thermal zones
and thermal binding parameters. The output data
can then be used to deploy thermal policies.
This patch adds also documentation regarding this
API and how to define tree nodes to use
this infrastructure.
Note that, in order to be able to have control
on the sensor registration on the DT thermal zone,
it was required to allow changing the thermal zone
.get_temp callback. For this reason, this patch
also removes the 'const' modifier from the .ops
field of thermal zone devices.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
This patch changes the thermal core driver to allow
registration of thermal zones without the .get_temp callback.
The idea behind this change is to allow lazy registration
of sensor callbacks.
The thermal zone will be disabled whenever the ops
does not contain a .get_temp callback. The sysfs interface
will be returning -EINVAL on any temperature read operation.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
|
|
Register generic netlink multicast groups as an array with
the family and give them contiguous group IDs. Then instead
of passing the global group ID to the various functions that
send messages, pass the ID relative to the family - for most
families that's just 0 because the only have one group.
This avoids the list_head and ID in each group, adding a new
field for the mcast group ID offset to the family.
At the same time, this allows us to prevent abusing groups
again like the quota and dropmon code did, since we can now
check that a family only uses a group it owns.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This doesn't really change anything, but prepares for the
next patch that will change the APIs to pass the group ID
within the family, rather than the global group ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
"This time we only have a few changes as there are no soc thermal
changes from Eduardo. The only big change is the introduction of
TMON, a tool to help visualize, tune, and test the thermal subsystem.
The rest is mostly cleanups and fixes all over.
Specifics:
- introduce TMON, a tool base on thermal sysfs I/F. It can be used
to visualize, tune and test the thermal subsystem.
- fix a zone/cooling device binding problem, when both thermal zone
bind parameters and .bind() callback are available"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
tools/thermal: Introduce tmon, a tool for thermal subsystem
thermal: Fix binding problem when there is thermal zone params
thermal: cpu_cooling: fix return value check in cpufreq_cooling_register()
Thermal: Check for validity before doing kfree
thermal/intel_powerclamp: Add newer CPU models
Thermal: Tidy up error handling in powerclamp_init
thermal: Kconfig: cosmetic fixes
ACPI/thermal : Remove zone disabled warning
typo in drivers/thermal/Kconfig: lpatform instead of platform
|
|
|
|
The thermal zone params can be used to set governor
to specific thermal governor for thermal zone device.
But if the thermal zone params has only governor name
without thermal bind params, then the thermal zone device
will not be binding to cooling device. Because tz->ops->bind
operator is not invoked in bind_tz() and bind_cdev() when
there is thermal zone params.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jinyoung Park <jinyoungp@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
