| Age | Commit message (Collapse) | Author |
|---|
|
The following fixes are done for tcc sysfs interface:
- TCC is 6 bits only from bit 29-24
- TCC of 0 is valid
- When BIT(31) is set, this register is read only
- Check for invalid tcc value
- Error for negative values
Fixes: fdf4f2fb8e899 ("drivers: thermal: processor_thermal_device: Export sysfs interface for TCC offset")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: stable@vger.kernel.org
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210628215803.75038-1-srinivas.pandruvada@linux.intel.com
|
|
Fix smatch warnings:
drivers/thermal/intel/int340x_thermal/processor_thermal_device_pci.c:258 proc_thermal_pci_probe() warn: missing error code 'ret'
Use PTR_ERR to return failure of thermal_zone_device_register().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210628183232.62877-1-srinivas.pandruvada@linux.intel.com
|
|
Add a new PCI driver which register a thermal zone and allows to get
notification for threshold violation by a RW trip point. These
notifications are delivered from the device using MSI based
interrupt.
The main difference between this new PCI driver and the existing
one is that the temperature and trip points directly use PCI
MMIO instead of using ACPI methods.
This driver registers a thermal zone "TCPU_PCI" in addition to the
legacy processor thermal device, which uses ACPI companion device
to set name, temperature and trips.
This driver is enabled for AlderLake.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210525204811.3793651-3-srinivas.pandruvada@linux.intel.com
|
|
Remove enumeration part from the processor_thermal_device to two
different modules. One for ACPI and one for PCI:
ACPI enumeration: int3401_thermal
PCI part: processor_thermal_device_pci_legacy
The current processor_thermal_device now just implements interface
functions to be used by the ACPI and PCI enumeration module. This is
done by:
1. Make functions proc_thermal_add() and proc_thermal_remove() non static
and export them for usage in other processor_thermal_device_pci_legacy.c
and in int3401_thermal.c.
2. Move the sysfs file creation for TCC offset and power limit attribute
group to the proc_thermal_add() from the individual enumeration callbacks
for PCI and ACPI.
3. Create new interface functions proc_thermal_mmio_add() and
proc_thermal_mmio_remove() which will be called from the
processor_thermal_device_pci_legacy module.
4. Export proc_thermal_resume(), so that it can be used by power
management callbacks.
5. Remove special check for double enumeration as it never happens.
While here, fix some cleanup on error conditions in proc_thermal_add().
No functional changes are expected with this change.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210525204811.3793651-2-srinivas.pandruvada@linux.intel.com
|
|
Switch to use find_first_zero_bit() instead of open-coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210618153451.89246-1-andriy.shevchenko@linux.intel.com
|
|
Export additional attributes:
ddr_data_rate (RO) : Show current DDR (Double Data Rate) data rate.
rfi_restriction (RW) : Show or set current state for RFI (Radio
Frequency Interference) protection.
These attributes use mailbox commands to get/set information. Here
command codes are:
0x0007: Read RFI restriction
0x0107: Read DDR data rate
0x0008: Write RFI restriction
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210517061441.1921901-3-srinivas.pandruvada@linux.intel.com
|
|
Export the mailbox interface to be used by other modules. Also change
command id and response from u8 to u32 data type.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210517061441.1921901-2-srinivas.pandruvada@linux.intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"A bunch of x86/urgent stuff accumulated for the last two weeks so
lemme unload it to you.
It should be all totally risk-free, of course. :-)
- Fix out-of-spec hardware (1st gen Hygon) which does not implement
MSR_AMD64_SEV even though the spec clearly states so, and check
CPUID bits first.
- Send only one signal to a task when it is a SEGV_PKUERR si_code
type.
- Do away with all the wankery of reserving X amount of memory in the
first megabyte to prevent BIOS corrupting it and simply and
unconditionally reserve the whole first megabyte.
- Make alternatives NOP optimization work at an arbitrary position
within the patched sequence because the compiler can put
single-byte NOPs for alignment anywhere in the sequence (32-bit
retpoline), vs our previous assumption that the NOPs are only
appended.
- Force-disable ENQCMD[S] instructions support and remove
update_pasid() because of insufficient protection against FPU state
modification in an interrupt context, among other xstate horrors
which are being addressed at the moment. This one limits the
fallout until proper enablement.
- Use cpu_feature_enabled() in the idxd driver so that it can be
build-time disabled through the defines in disabled-features.h.
- Fix LVT thermal setup for SMI delivery mode by making sure the APIC
LVT value is read before APIC initialization so that softlockups
during boot do not happen at least on one machine.
- Mark all legacy interrupts as legacy vectors when the IO-APIC is
disabled and when all legacy interrupts are routed through the PIC"
* tag 'x86_urgent_for_v5.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sev: Check SME/SEV support in CPUID first
x86/fault: Don't send SIGSEGV twice on SEGV_PKUERR
x86/setup: Always reserve the first 1M of RAM
x86/alternative: Optimize single-byte NOPs at an arbitrary position
x86/cpufeatures: Force disable X86_FEATURE_ENQCMD and remove update_pasid()
dmaengine: idxd: Use cpu_feature_enabled()
x86/thermal: Fix LVT thermal setup for SMI delivery mode
x86/apic: Mark _all_ legacy interrupts when IO/APIC is missing
|
|
There are machines out there with added value crap^WBIOS which provide an
SMI handler for the local APIC thermal sensor interrupt. Out of reset,
the BSP on those machines has something like 0x200 in that APIC register
(timestamps left in because this whole issue is timing sensitive):
[ 0.033858] read lvtthmr: 0x330, val: 0x200
which means:
- bit 16 - the interrupt mask bit is clear and thus that interrupt is enabled
- bits [10:8] have 010b which means SMI delivery mode.
Now, later during boot, when the kernel programs the local APIC, it
soft-disables it temporarily through the spurious vector register:
setup_local_APIC:
...
/*
* If this comes from kexec/kcrash the APIC might be enabled in
* SPIV. Soft disable it before doing further initialization.
*/
value = apic_read(APIC_SPIV);
value &= ~APIC_SPIV_APIC_ENABLED;
apic_write(APIC_SPIV, value);
which means (from the SDM):
"10.4.7.2 Local APIC State After It Has Been Software Disabled
...
* The mask bits for all the LVT entries are set. Attempts to reset these
bits will be ignored."
And this happens too:
[ 0.124111] APIC: Switch to symmetric I/O mode setup
[ 0.124117] lvtthmr 0x200 before write 0xf to APIC 0xf0
[ 0.124118] lvtthmr 0x10200 after write 0xf to APIC 0xf0
This results in CPU 0 soft lockups depending on the placement in time
when the APIC soft-disable happens. Those soft lockups are not 100%
reproducible and the reason for that can only be speculated as no one
tells you what SMM does. Likely, it confuses the SMM code that the APIC
is disabled and the thermal interrupt doesn't doesn't fire at all,
leading to CPU 0 stuck in SMM forever...
Now, before
4f432e8bb15b ("x86/mce: Get rid of mcheck_intel_therm_init()")
due to how the APIC_LVTTHMR was read before APIC initialization in
mcheck_intel_therm_init(), it would read the value with the mask bit 16
clear and then intel_init_thermal() would replicate it onto the APs and
all would be peachy - the thermal interrupt would remain enabled.
But that commit moved that reading to a later moment in
intel_init_thermal(), resulting in reading APIC_LVTTHMR on the BSP too
late and with its interrupt mask bit set.
Thus, revert back to the old behavior of reading the thermal LVT
register before the APIC gets initialized.
Fixes: 4f432e8bb15b ("x86/mce: Get rid of mcheck_intel_therm_init()")
Reported-by: James Feeney <james@nurealm.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lkml.kernel.org/r/YKIqDdFNaXYd39wz@zn.tnic
|
|
After commit 81ad4276b505 ("Thermal: Ignore invalid trip points") all
user_space governor notifications via RW trip point is broken in intel
thermal drivers. This commits marks trip_points with value of 0 during
call to thermal_zone_device_register() as invalid. RW trip points can be
0 as user space will set the correct trip temperature later.
During driver init, x86_package_temp and all int340x drivers sets RW trip
temperature as 0. This results in all these trips marked as invalid by
the thermal core.
To fix this initialize RW trips to THERMAL_TEMP_INVALID instead of 0.
Cc: <stable@vger.kernel.org>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210430122343.1789899-1-srinivas.pandruvada@linux.intel.com
|
|
On Intel processors, the core frequency can be reduced below OS request,
when the current temperature reaches the TCC (Thermal Control Circuit)
activation temperature.
The default TCC activation temperature is specified by
MSR_IA32_TEMPERATURE_TARGET. However, it can be adjusted by specifying an
offset in degrees C, using the TCC Offset bits in the same MSR register.
This patch introduces a cooling devices driver that utilizes the TCC
Offset feature. The bigger the current cooling state is, the lower the
effective TCC activation temperature is, so that the processors can be
throttled earlier before system critical overheats.
Note that, on different platforms, the behavior might be different on
how fast the setting takes effect, and how much the CPU frequency is
reduced.
This patch has been tested on a KabyLake mobile platform from me, and also
on a CometLake platform from Doug.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210412125901.12549-1-rui.zhang@intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Use the newly introduced 'hot' and 'critical' ops for the acpi
thermal driver (Daniel Lezcano)
- Remove the notify ops as it is no longer used (Daniel Lezcano)
- Remove the 'forced passive' option and the unused bind/unbind
functions (Daniel Lezcano)
- Remove the THERMAL_TRIPS_NONE and the code cleanup around this macro
(Daniel Lezcano)
- Rework the delays to make them pre-computed instead of computing them
again and again at each polling interval (Daniel Lezcano)
- Remove the pointless 'thermal_zone_device_reset' function (Daniel
Lezcano)
- Use the critical and hot ops to prevent an unexpected system shutdown
on int340x (Kai-Heng Feng)
- Make the cooling device state private to the thermal subsystem
(Daniel Lezcano)
- Prevent to use not-power-aware actor devices with the power allocator
governor (Lukasz Luba)
- Remove 'zx' and 'tango' support along with the corresponding
platforms (Arnd Bergman)
- Fix several issues on the Omap thermal driver (Tony Lindgren)
- Add support for adc-tm5 PMIC thermal monitor for Qcom platforms
(Dmitry Baryshkov)
- Fix an initialization loop in the adc-tm5 (Colin Ian King)
- Fix a return error check in the cpufreq cooling device (Viresh Kumar)
* tag 'thermal-v5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (26 commits)
thermal: cpufreq_cooling: freq_qos_update_request() returns < 0 on error
thermal: qcom: Fix comparison with uninitialized variable channels_available
thermal: qcom: add support for adc-tm5 PMIC thermal monitor
dt-bindings: thermal: qcom: add adc-thermal monitor bindings
thermal: ti-soc-thermal: Use non-inverted define for omap4
thermal: ti-soc-thermal: Simplify polling with iopoll
thermal: ti-soc-thermal: Fix stuck sensor with continuous mode for 4430
thermal: ti-soc-thermal: Skip pointless register access for dra7
thermal/drivers/zx: Remove zx driver
thermal/drivers/tango: Remove tango driver
thermal: power allocator: fail binding for non-power actor devices
thermal/core: Make cooling device state change private
thermal: intel: pch: Fix unexpected shutdown at critical temperature
thermal: int340x: Fix unexpected shutdown at critical temperature
thermal/core: Remove pointless thermal_zone_device_reset() function
thermal/core: Remove ms based delay fields
thermal/core: Use precomputed jiffies for the polling
thermal/core: Precompute the delays from msecs to jiffies
thermal/core: Remove unused macro THERMAL_TRIPS_NONE
thermal/core: Remove THERMAL_TRIPS_NONE test
...
|
|
This functionality has nothing to do with MCE, move it to the thermal
framework and untangle it from MCE.
Requested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lkml.kernel.org/r/20210202121003.GD18075@zn.tnic
|
|
Like previous patch, the intel_pch_thermal device is not in ACPI
ThermalZone namespace, so a critical trip doesn't mean shutdown.
Override the default .critical callback to prevent surprising thermal
shutdoown.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201221172345.36976-2-kai.heng.feng@canonical.com
|
|
We are seeing thermal shutdown on Intel based mobile workstations, the
shutdown happens during the first trip handle in
thermal_zone_device_register():
kernel: thermal thermal_zone15: critical temperature reached (101 C), shutting down
However, we shouldn't do a thermal shutdown here, since
1) We may want to use a dedicated daemon, Intel's thermald in this case,
to handle thermal shutdown.
2) For ACPI based system, _CRT doesn't mean shutdown unless it's inside
ThermalZone namespace. ACPI Spec, 11.4.4 _CRT (Critical Temperature):
"... If this object it present under a device, the device’s driver
evaluates this object to determine the device’s critical cooling
temperature trip point. This value may then be used by the device’s
driver to program an internal device temperature sensor trip point."
So a "critical trip" here merely means we should take a more aggressive
cooling method.
As int340x device isn't present under ACPI ThermalZone, override the
default .critical callback to prevent surprising thermal shutdown.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201221172345.36976-1-kai.heng.feng@canonical.com
|
|
Add ACPI IDs for thermal drivers for Alder Lake support.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201117194802.503337-1-srinivas.pandruvada@linux.intel.com
|
|
Change "Burusty" to "bursty".
Reported-by: Michael Larabel <Michael@phoronix.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210213324.2113041-1-srinivas.pandruvada@linux.intel.com
|
|
Use macro for temperature calculation
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210124801.13850-1-sumeet.r.pawnikar@intel.com
|
|
Added processor thermal device mail box interface for workload hints
setting. These hints will give indication to hardware to better manage
power and thermals. The supported hints are:
idle
semi_active
burusty
sustained
battery_life
For example when the system is on battery, the hardware can be less
aggressive in power ramp up.
This will create an attribute group at
/sys/bus/pci/devices/0000:00:04.0/workload_request
This folder contains two attributes:
workload_available_types : (RO): This shows available workload types
workload_type: (RW) : Allows to set and get current workload type
setting
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-4-srinivas.pandruvada@linux.intel.com
|
|
Add support for RFIM (Radio Frequency Interference Mitigation) support
via processor thermal PCI device. This drivers allows adjustment of
FIVR (Fully Integrated Voltage Regulator) and DDR (Double Data Rate)
frequencies to avoid RF interference with WiFi and 5G.
Switching voltage regulators (VR) generate radiated EMI or RFI at the
fundamental frequency and its harmonics. Some harmonics may interfere
with very sensitive wireless receivers such as Wi-Fi and cellular that
are integrated into host systems like notebook PCs. One of mitigation
methods is requesting SOC integrated VR (IVR) switching frequency to a
small % and shift away the switching noise harmonic interference from
radio channels. OEM or ODMs can use the driver to control SOC IVR
operation within the range where it does not impact IVR performance.
DRAM devices of DDR IO interface and their power plane can generate EMI
at the data rates. Similar to IVR control mechanism, Intel offers a
mechanism by which DDR data rates can be changed if several conditions
are met: there is strong RFI interference because of DDR; CPU power
management has no other restriction in changing DDR data rates;
PC ODMs enable this feature (real time DDR RFI Mitigation referred to as
DDR-RFIM) for Wi-Fi from BIOS.
This change exports two folders under /sys/bus/pci/devices/0000:00:04.0.
One folder "fivr" contains all attributes exposed for controling FIVR
features. The other folder "dvfs" contains all attributes for DDR
features.
Changes done to implement:
- New module for rfim interfaces
- Two new per processor features for DDR and FIVR
- Enable feature for Tiger Lake (FIVR only) and Alder Lake
The attributes exposed and explanation:
FIVR attributes
vco_ref_code_lo (RW): The VCO reference code is an 11-bit field and
controls the FIVR switching frequency. This is the 3-bit LSB field.
vco_ref_code_hi (RW): The VCO reference code is an 11-bit field and
controls the FIVR switching frequency. This is the 8-bit MSB field.
spread_spectrum_pct (RW): Set the FIVR spread spectrum clocking
percentage
spread_spectrum_clk_enable (RW): Enable/disable of the FIVR spread
spectrum clocking feature
rfi_vco_ref_code (RW): This field is a read only status register which
reflects the current FIVR switching frequency
fivr_fffc_rev (RW): This field indicated the revision of the FIVR HW.
DVFS attributes
rfi_restriction_run_busy (RW): Request the restriction of specific DDR
data rate and set this value 1. Self reset to 0 after operation.
rfi_restriction_err_code (RW): Values: 0 :Request is accepted, 1:Feature
disabled, 2: the request restricts more points than it is allowed
rfi_restriction_data_rate_Delta (RW): Restricted DDR data rate for RFI
protection: Lower Limit
rfi_restriction_data_rate_Base (RW): Restricted DDR data rate for RFI
protection: Upper Limit
ddr_data_rate_point_0 (RO): DDR data rate selection 1st point
ddr_data_rate_point_1 (RO): DDR data rate selection 2nd point
ddr_data_rate_point_2 (RO): DDR data rate selection 3rd point
ddr_data_rate_point_3 (RO): DDR data rate selection 4th point
rfi_disable (RW): Disable DDR rate change feature
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-3-srinivas.pandruvada@linux.intel.com
|
|
Added AlderLake PCI device id to support processor thermal driver. Reuse
the feature set (just includes RAPL) from previous generations.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-2-srinivas.pandruvada@linux.intel.com
|
|
The Processor Thermal PCI device supports multiple features. Currently
we export only RAPL. But we need more features from this device exposed
for Tiger Lake and Alder Lake based platforms. So re-structure the
current MMIO interface, so that more features can be added cleanly.
No functional changes are expected with this change.
Changes done in this patch:
- Using PCI_DEVICE_DATA(), hence names of defines changed
- Move RAPL MMIO code to its own module
- Move the RAPL MMIO offsets to RAPL MMIO module
- Adjust Kconfig dependency of PROC_THERMAL_MMIO_RAPL
- Per processor driver data now contains the supported features
- Moved all the common data structures and defines to a common header
file
- This new header file contains all the processor_thermal_* interfaces
- Based on the features supported the module interface is called
- Each module atleast provides one add and one remove function
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-1-srinivas.pandruvada@linux.intel.com
|
|
The reference to acpi_gbl_FADT causes a build error when ACPI is not
enabled. Fix by making that conditional on CONFIG_ACPI.
../drivers/thermal/intel/intel_pch_thermal.c: In function 'pch_wpt_suspend':
../drivers/thermal/intel/intel_pch_thermal.c:217:8: error: 'acpi_gbl_FADT' undeclared (first use in this function); did you mean 'acpi_get_type'?
if (!(acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0))
^~~~~~~~~~~~~
Fixes: ef63b043ac86 ("thermal: intel: pch: fix S0ix failure due to PCH temperature above threshold")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Amit Kucheria <amitk@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201117023807.8266-1-rdunlap@infradead.org
|
|
I noticed that I couldn't read the PCH temperature on my workstation
(C620 series chipset, w/ 2x Xeon Gold 5215 CPUs) directly, but had to go
through IPMI. Looking at the data sheet, it looks to me like the
existing intel PCH thermal driver should work without changes for
Lewisburg.
I suspect there's some other PCI IDs missing. But I hope somebody at
Intel would have an easier time figuring that out than I...
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/lkml/20200115184415.1726953-1-andres@anarazel.de/
Signed-off-by: Andres Freund <andres@anarazel.de>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201113204916.1144907-1-andres@anarazel.de
|
|
When system tries to enter S0ix suspend state, just after active load
scenarios, it fails due to PCH current temperature is higher than set
threshold.
This patch introduces delay loop mechanism that allows PCH temperature
to go down below threshold during suspend so it won't fail to enter S0ix.
Add delay loop timeout and count as module parameters for user to tune it,
if required based on system design. This change notifies the different
warning messages like when PCH temperature above the threshold and
executing delay loop. Also, notify the messages when it success or
failure for S0ix entry.
Previously out of 1000 runs around 3 to 5 times it might fail to enter
S0ix just after heavy workload. With this change, S0ix failures reduced
as PCH cools down below threshold.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201106170633.20838-1-sumeet.r.pawnikar@intel.com
|
|
When firmware requests keep alive response, send an event to user space
to confirm by using imok sysfs entry.
Create a new sysf entry called "imok". User space can write an integer,
which results in execution of IMOK ACPI method of INT3400 thermal zone
device. This results in sending response to firmware request for keep
alive.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200915223650.406046-4-srinivas.pandruvada@linux.intel.com
|
|
When we receive ACPI notification for OEM variable change pass the
notification to user space handler. This will avoid polling for
OEM variable change from user space.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200915223650.406046-2-srinivas.pandruvada@linux.intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add support to enable/disable the thermal zones resulting on core
code and drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events,
temperature and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian
Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz
Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
* tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (40 commits)
thermal: intel: intel_pch_thermal: Add Cannon Lake Low Power PCH support
thermal: mediatek: Add tsensor support for V2 thermal system
thermal: mediatek: Prepare to add support for other platforms
thermal: Update power allocator and devfreq cooling to SPDX licensing
MAINTAINERS: update entry to thermal governors file name prefixing
thermal: core: Add thermal zone enable/disable notification
thermal: qcom: tsens-v0_1: Add support for MSM8939
dt-bindings: tsens: qcom: Document MSM8939 compatible
thermal: core: Fix thermal zone lookup by ID
thermal: int340x: processor_thermal: fix: update Jasper Lake PCI id
thermal: imx8mm: Support module autoloading
thermal: ti-soc-thermal: Fix reversed condition in ti_thermal_expose_sensor()
MAINTAINERS: Add maintenance information for IPA
thermal: rcar_gen3_thermal: Do not shadow thcode variable
dt-bindings: thermal: Get rid of thermal.txt and replace references
thermal: core: Move initialization after core initcall
thermal: netlink: Improve the initcall ordering
net: genetlink: Move initialization to core_initcall
thermal: rcar_gen3_thermal: Add r8a774e1 support
thermal/drivers/clock_cooling: Remove clock_cooling code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
|
|
Add LP (Low Power) PCH id for Cannon Lake (CNL) based platforms.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1596097503-27924-1-git-send-email-sumeet.r.pawnikar@intel.com
|
|
Update PCI device id for Jasper Lake processor thermal device.
With this proc_thermal driver is getting loaded and processor
thermal functionality works on Jasper Lake system.
Fixes: f64a6583d3f5 ("thermal: int340x: processor_thermal: Add Jasper Lake support")
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1595577146-1221-1-git-send-email-sumeet.r.pawnikar@intel.com
|
|
Downgrade "Unsupported event" message from dev_err to dev_dbg to avoid
flooding with this message on some platforms.
Cc: stable@vger.kernel.org # v5.4+
Suggested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Alex Hung <alex.hung@canonical.com>
[ rzhang: fix typo in changelog ]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200615223957.183153-1-alex.hung@canonical.com
|
|
Starting from commit "thermal/int340x_thermal: Don't require IDSP to
exist", priv->current_uuid_index is initialized to -1. This value may
be passed to int3400_thermal_run_osc() from int3400_thermal_set_mode,
contributing to page fault when accessing int3400_thermal_uuids array
at index -1.
This commit adds a check on uuid value to int3400_thermal_run_osc.
Fixes: 8d485da0ddee ("thermal/int340x_thermal: Don't require IDSP to exist")
Signed-off-by: Bartosz Szczepanek <bsz@semihalf.com>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
[ rzhang: Add Fixes tag ]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200708134613.131555-1-bsz@semihalf.com
|
|
set_mode() is only called when tzd's mode is about to change. Actual
setting is performed in thermal_core, in thermal_zone_device_set_mode().
The meaning of set_mode() callback is actually to notify the driver about
the mode being changed and giving the driver a chance to oppose such
change.
To better reflect the purpose of the method rename it to change_mode()
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-12-andrzej.p@collabora.com
|
|
Setting polling_delay is now done at thermal_core level (by not polling
DISABLED devices), so no need to repeat this code.
int340x: Checking for an impossible enum value is unnecessary.
acpi/thermal: It only prints debug messages.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-11-andrzej.p@collabora.com
|
|
Some thermal zone devices never change their state, so they should be
always enabled.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-9-andrzej.p@collabora.com
|
|
Use thermal_zone_device_{en|dis}able() and thermal_zone_device_is_enabled().
Consequently, all set_mode() implementations in drivers:
- can stop modifying tzd's "mode" member,
- shall stop taking tzd's lock, as it is taken in the helpers
- shall stop calling thermal_zone_device_update() as it is called in the
helpers
- can assume they are called when the mode truly changes, so checks to
verify that can be dropped
Not providing set_mode() by a driver no longer prevents the core from
being able to set tzd's mode, so the relevant check in mode_store() is
removed.
Other comments:
- acpi/thermal.c: tz->thermal_zone->mode will be updated only after we
return from set_mode(), so use function parameter in thermal_set_mode()
instead, no need to call acpi_thermal_check() in set_mode()
- thermal/imx_thermal.c: regmap writes and mode assignment are done in
thermal_zone_device_{en|dis}able() and set_mode() callback
- thermal/intel/intel_quark_dts_thermal.c: soc_dts_{en|dis}able() are a
part of set_mode() callback, so they don't need to modify tzd->mode, and
don't need to fall back to the opposite mode if unsuccessful, as the return
value will be propagated to thermal_zone_device_{en|dis}able() and
ultimately tzd's member will not be changed in thermal_zone_device_set_mode().
- thermal/of-thermal.c: no need to set zone->mode to DISABLED in
of_parse_thermal_zones() as a tzd is kzalloc'ed so mode is DISABLED anyway
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-8-andrzej.p@collabora.com
|
|
get_mode() is now redundant, as the state is stored in struct
thermal_zone_device.
Consequently the "mode" attribute in sysfs can always be visible, because
it is always possible to get the mode from struct tzd.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-6-andrzej.p@collabora.com
|
|
Prepare for eliminating get_mode().
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-5-andrzej.p@collabora.com
|
|
Prepare for storing mode in struct thermal_zone_device.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-3-andrzej.p@collabora.com
|
|
Because SCHED_FIFO is a broken scheduler model (see previous patches)
take away the priority field, the kernel can't possibly make an
informed decision.
Effectively no change.
Cc: rafael.j.wysocki@intel.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
|
|
The IDSP method doesn't appear to exist on the most recent Intel platforms:
instead, the IDSP data is included in the GDDV blob. Since we probably
don't want to decompress and parse that in-kernel, just allow any UUID to
be written if IDSP is missing.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
[ rzhang: fix checkpatch warning in changelog ]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200414020953.255364-3-matthewgarrett@google.com
|
|
The platform vendor may expose an array of OEM-specific values to be used
in determining DPTF policy. These are obtained via the ODVP method, and
then simply exposed in sysfs. In addition, they are updated when a
notification is received or when the DPTF policy is changed by userland.
Conflicts:
drivers/thermal/intel/int340x_thermal/int3400_thermal.c
Signed-off-by: Matthew Garrett <mjg59@google.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200414020953.255364-2-matthewgarrett@google.com
|
|
Implementing DPTF properly requires making use of firmware-provided
information associated with the INT3400 device. Calling GDDV provides a
buffer of information which userland can then interpret to determine
appropriate DPTF policy.
Conflicts:
drivers/thermal/intel/int340x_thermal/int3400_thermal.c
Signed-off-by: Matthew Garrett <mjg59@google.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200414020953.255364-1-matthewgarrett@google.com
|
|
int3400_thermal_ops is used inside int3400_thermal_probe() only after
the assignments, which can just as well be made statically at struct's
initizer.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200414180105.20042-2-andrzej.p@collabora.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Convert tsens configuration DT binding to yaml (Rajeshwari)
- Add interrupt support on the rcar sensor (Niklas Söderlund)
- Add a new Spreadtrum thermal driver (Baolin Wang)
- Add thermal binding for the fsl scu board, a new API to retrieve the
sensor id bound to the thermal zone and i.MX system controller sensor
(Anson Huang))
- Remove warning log when a deferred probe is requested on Exynos
(Marek Szyprowski)
- Add the thermal monitoring unit support for imx8mm with its DT
bindings (Anson Huang)
- Rephrase the Kconfig text for clarity (Linus Walleij)
- Use the gpio descriptor for the ti-soc-thermal (Linus Walleij)
- Align msg structure to 4 bytes for i.MX SC, fix the Kconfig
dependency, add the __may_be unused annotation for PM functions and
the COMPILE_TEST option for imx8mm (Anson Huang)
- Fix a dependency on regmap in Kconfig for qoriq (Yuantian Tang)
- Add DT binding and support for the rcar gen3 r8a77961 and improve the
error path on the rcar init function (Niklas Söderlund)
- Cleanup and improvements for the tsens Qcom sensor (Amit Kucheria)
- Improve code by removing lock and caching values in the rcar thermal
sensor (Niklas Söderlund)
- Cleanup in the qoriq drivers and add a call to
imx_thermal_unregister_legacy_cooling in the removal function (Anson
Huang)
- Remove redundant 'maxItems' in tsens and sprd DT bindings (Rob
Herring)
- Change the thermal DT bindings by making the cooling-maps optional
(Yuantian Tang)
- Add Tiger Lake support (Sumeet Pawnikar)
- Use scnprintf() for avoiding potential buffer overflow (Takashi Iwai)
- Make pkg_temp_lock a raw_spinlock_t(Clark Williams)
- Fix incorrect data types by changing them to signed on i.MX SC (Anson
Huang)
- Replace zero-length array with flexible-array member (Gustavo A. R.
Silva)
- Add support for i.MX8MP in the driver and in the DT bindings (Anson
Huang)
- Fix return value of the cpufreq_set_cur_state() function (Willy
Wolff)
- Remove abusing and scary WARN_ON in the cpufreq cooling device
(Daniel Lezcano)
- Fix build warning of incorrect argument type reported by sparse on
imx8mm (Anson Huang)
- Fix stub for the devfreq cooling device (Martin Blumenstingl)
- Fix cpu idle cooling documentation (Sergey Vidishev)
* tag 'thermal-v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (52 commits)
Documentation: cpu-idle-cooling: Fix diagram for 33% duty cycle
thermal: devfreq_cooling: inline all stubs for CONFIG_DEVFREQ_THERMAL=n
thermal: imx8mm: Fix build warning of incorrect argument type
thermal/drivers/cpufreq_cooling: Remove abusing WARN_ON
thermal/drivers/cpufreq_cooling: Fix return of cpufreq_set_cur_state
thermal: imx8mm: Add i.MX8MP support
dt-bindings: thermal: imx8mm-thermal: Add support for i.MX8MP
thermal: qcom: tsens.h: Replace zero-length array with flexible-array member
thermal: imx_sc_thermal: Fix incorrect data type
thermal: int340x_thermal: Use scnprintf() for avoiding potential buffer overflow
thermal: int340x: processor_thermal: Add Tiger Lake support
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
dt-bindings: thermal: make cooling-maps property optional
dt-bindings: thermal: qcom-tsens: Remove redundant 'maxItems'
dt-bindings: thermal: sprd: Remove redundant 'maxItems'
thermal: imx: Calling imx_thermal_unregister_legacy_cooling() in .remove
thermal: qoriq: Sort includes alphabetically
thermal: qoriq: Use devm_add_action_or_reset() to handle all cleanups
thermal: rcar_thermal: Remove lock in rcar_thermal_get_current_temp()
thermal: rcar_thermal: Do not store ctemp in rcar_thermal_priv
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Additional ACPI updates.
These update the ACPICA code in the kernel to the 20200326 upstream
revision, fix an ACPI-related CPU hotplug deadlock on x86, update
Intel Tiger Lake device IDs in some places, add a new ACPI backlight
blacklist entry, update the "acpi_backlight" kernel command line
switch documentation and clean up a CPPC library routine.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20200326
including:
* Fix for a typo in a comment field (Bob Moore)
* acpiExec namespace init file fixes (Bob Moore)
* Addition of NHLT to the known tables list (Cezary Rojewski)
* Conversion of PlatformCommChannel ASL keyword to PCC (Erik
Kaneda)
* acpiexec cleanup (Erik Kaneda)
* WSMT-related typo fix (Erik Kaneda)
* sprintf() utility function fix (John Levon)
* IVRS IVHD type 11h parsing implementation (Michał Żygowski)
* IVRS IVHD type 10h reserved field name fix (Michał Żygowski)
- Fix ACPI-related CPU hotplug deadlock on x86 (Qian Cai)
- Fix Intel Tiger Lake ACPI device IDs in several places (Gayatri
Kammela)
- Add ACPI backlight blacklist entry for Acer Aspire 5783z (Hans de
Goede)
- Fix documentation of the "acpi_backlight" kernel command line
switch (Randy Dunlap)
- Clean up the acpi_get_psd_map() CPPC library routine (Liguang
Zhang)"
* tag 'acpi-5.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86: ACPI: fix CPU hotplug deadlock
thermal: int340x_thermal: fix: Update Tiger Lake ACPI device IDs
platform/x86: intel-hid: fix: Update Tiger Lake ACPI device ID
ACPI: Update Tiger Lake ACPI device IDs
ACPI: video: Use native backlight on Acer Aspire 5783z
ACPI: video: Docs update for "acpi_backlight" kernel parameter options
ACPICA: Update version 20200326
ACPICA: Fixes for acpiExec namespace init file
ACPICA: Add NHLT table signature
ACPICA: WSMT: Fix typo, no functional change
ACPICA: utilities: fix sprintf()
ACPICA: acpiexec: remove redeclaration of acpi_gbl_db_opt_no_region_support
ACPICA: Change PlatformCommChannel ASL keyword to PCC
ACPICA: Fix IVRS IVHD type 10h reserved field name
ACPICA: Implement IVRS IVHD type 11h parsing
ACPICA: Fix a typo in a comment field
ACPI: CPPC: clean up acpi_get_psd_map()
|
|
Tiger Lake's new unique ACPI device IDs for Intel thermal driver are not
valid because of missing 'C' in the IDs. Fix the IDs by updating them.
After the update, the new IDs should now look like
INT1040 --> INTC1040
INT1043 --> INTC1043
Fixes: 9b1b5535dfc9 ("thermal: int340x_thermal: Add Tiger Lake ACPI device IDs")
Cc: 5.6+ <stable@vger.kernel.org> # 5.6+
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"The main changes in this cycle were:
Kernel side changes:
- A couple of x86/cpu cleanups and changes were grandfathered in due
to patch dependencies. These clean up the set of CPU model/family
matching macros with a consistent namespace and C99 initializer
style.
- A bunch of updates to various low level PMU drivers:
* AMD Family 19h L3 uncore PMU
* Intel Tiger Lake uncore support
* misc fixes to LBR TOS sampling
- optprobe fixes
- perf/cgroup: optimize cgroup event sched-in processing
- misc cleanups and fixes
Tooling side changes are to:
- perf {annotate,expr,record,report,stat,test}
- perl scripting
- libapi, libperf and libtraceevent
- vendor events on Intel and S390, ARM cs-etm
- Intel PT updates
- Documentation changes and updates to core facilities
- misc cleanups, fixes and other enhancements"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (89 commits)
cpufreq/intel_pstate: Fix wrong macro conversion
x86/cpu: Cleanup the now unused CPU match macros
hwrng: via_rng: Convert to new X86 CPU match macros
crypto: Convert to new CPU match macros
ASoC: Intel: Convert to new X86 CPU match macros
powercap/intel_rapl: Convert to new X86 CPU match macros
PCI: intel-mid: Convert to new X86 CPU match macros
mmc: sdhci-acpi: Convert to new X86 CPU match macros
intel_idle: Convert to new X86 CPU match macros
extcon: axp288: Convert to new X86 CPU match macros
thermal: Convert to new X86 CPU match macros
hwmon: Convert to new X86 CPU match macros
platform/x86: Convert to new CPU match macros
EDAC: Convert to new X86 CPU match macros
cpufreq: Convert to new X86 CPU match macros
ACPI: Convert to new X86 CPU match macros
x86/platform: Convert to new CPU match macros
x86/kernel: Convert to new CPU match macros
x86/kvm: Convert to new CPU match macros
x86/perf/events: Convert to new CPU match macros
...
|
|
The pkg_temp_lock spinlock is acquired in the thermal vector handler which
is truly atomic context even on PREEMPT_RT kernels.
The critical sections are tiny, so change it to a raw spinlock.
Signed-off-by: Clark Williams <williams@redhat.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191008110021.2j44ayunal7fkb7i@linutronix.de
|
